Evaluation of alkali flooding combined with intermittent flow in carbonate reservoir

The majority of carbonate reservoir is oil-wet, which is an unfavorable condition for oil production. Generally, the total oil recovery after both primary and secondary recovery in an oil-wet reservoir is low. The amount of producible oil by enhanced oil recovery techniques is still large. Alkali substances are proven to be able to reverse rock wettability from oil-wet to water-wet, which is a favorable condition for oil production. However, the wettability reversal mechanism would require a noneconomical aging period to reach the maximum reversal condition. An intermittent flow with the optimum pausing period is then combined with alkali flooding (combination technique) to increase the wettability reversal mechanism and as a consequence, oil recovery is improved. The aims of this study are to evaluate the efficiency of the combination technique and to study the parameters that affect this method. In order to implement alkali flooding, reservoir rock and fluid properties were gathered, e.g. interfacial tension of fluids, rock wettability, etc. The flooding efficiency curves are obtained from core flooding and used as a major criterion for evaluation the performance of technique. The combination technique improves oil recovery when the alkali concentration is lower than 1% wt. (where the wettability reversal mechanism is dominant). The soap plug (that appears when high alkali concentration is used) is absent in this combination as seen from no drop of production rate. Moreover, the use of low alkali concentration limits alkali loss. This combination probably improves oil recovery also in the fractured carbonate reservoirs in which oil is uneconomically produced. The results from the current study indicate that the combination technique is an option that can improve the production of carbonate reservoirs. And a less quantity of alkali is consumed in the process.

Determinação das formas de nitrogênio e nitrogênio total em rochas-reservatório de petróleo por destilação com arraste de vapor e método do indofenol

Several extraction procedures are described for the determination of exchangeable and fixed ammonium, nitrate + nitrite, total exchangeable nitrogen and total nitrogen in certified reference soils and petroleum reservoir rock samples by steam distillation and indophenol method. After improvement of the original distillation system, an increase in worker safety, a reduction in time consumption, a decrease of 73% in blank value and an analysis without ammonia loss, which could possibly occur, were achieved. The precision (RSD < 8%, n = 3) and the detection limit (9 mg kg-1 NH4+-N) are better than those of published procedures.

Seismic activity triggered by water wells in the Parana Basin, Brazil

Triggered seismicity is commonly associated with deep water reservoirs or injection wells where water is injected at high pressure into the reservoir rock. However, earth tremors related solely to the opening of groundwater wells are extremely rare. Here we present a clear case of seismicity induced by pore-pressure changes following the drilling of water wells that exploit a confined aquifer in the intracratonic Parana Basin of southeastern Brazil. Since 2004, shallow seismic activity, with magnitudes up to 2.9 and intensities V MM, has been observed near deep wells (120-200 m) that were drilled in early 2003 near the town of Bebedouro. The wells were drilled for irrigation purposes, cross a sandstone layer about 60-80 m thick and extract water from a confined aquifer in fractured zones between basalt flow layers. Seismic activity, mainly event swarms, has occurred yearly since 2004, mostly during the rainy season when the wells are not pumped. During the dry season when the wells are pumped almost continuously, the activity is very low. A seismographic network, installed in March 2005, has located more than 2000 microearthquakes. The events are less than 1 km deep (mostly within the 0.5 km thick basalt layer) and cover an area roughly 1.5 km x 5 km across. The seismicity generally starts in a small area and expands to larger distances with an equivalent hydraulic diffusivity ranging from 0.06 to 0.6 m(2)/s. Geophysical and geothermal logging of several wells in the area showed that water from the shallow sandstone aquifer enters the well at the top and usually forms waterfalls. The waterfalls flow down the sides of the wells and feed the confined, fractured aquifer in the basalt layer at the bottom. Two seismic areas are observed: the main area surrounds several wells that are pumped continuously during the dry season, and a second area near another well (about 10 km from the first area) that is not used for irrigation and not pumped regularly. The main area displays cyclic annual activity, but the second area does not. We explain the earthquake swarms as being triggered by pore pressure diffusion in the fractured basalt layer due to additional pressure from the newly connected surface aquifer. This reaches critically prestressed areas up to a few kilometers away from the wells. During periods of continuous pumping, the reduction of pore pressure in the confined aquifer stops the seismic activity. Our study suggests that this kind of activity may be more common than previously thought and implies that many other cases of small tremors associated with the drilling of water wells may have gone unnoticed.

Análise gráfica de estruturas porosas sobre a ótica da estereologia

In this work we developed a computer simulation program for physics porous structures based on programming language C + + using a Geforce 9600 GT with the PhysX chip, originally developed for video games. With this tool, the ability of physical interaction between simulated objects is enlarged, allowing to simulate a porous structure, for example, reservoir rocks and structures with high density. The initial procedure for developing the simulation is the construction of porous cubic structure consisting of spheres with a single size and with varying sizes. In addition, structures can also be simulated with various volume fractions. The results presented are divided into two parts: first, the ball shall be deemed as solid grains, ie the matrix phase represents the porosity, the second, the spheres are considered as pores. In this case the matrix phase represents the solid phase. The simulations in both cases are the same, but the simulated structures are intrinsically different. To validate the results presented by the program, simulations were performed by varying the amount of grain, the grain size distribution and void fraction in the structure. All results showed statistically reliable and consistent with those presented in the literature. The mean values and distributions of stereological parameters measured, such as intercept linear section of perimeter area, sectional area and mean free path are in agreement with the results obtained in the literature for the structures simulated. The results may help the understanding of real structures.

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process

Estudo hidrogeológico do aqüífero Tubarão na área de afloramento da porção central do Estado de São Paulo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação automática da porosidade e zoneamento de perfis através da rede neural artificial competitiva

Duas das mais importantes atividades da interpretação de perfis para avaliação de reservatórios de hidrocarbonetos são o zoneamento do perfil (log zonation) e o cálculo da porosidade efetiva das rochas atravessadas pelo poço. O zoneamento é a interpretação visual do perfil para identificação das camadas reservatório e, consequentemente, dos seus limites verticais, ou seja, é a separação formal do perfil em rochas reservatório e rochas selante. Todo procedimento de zoneamento é realizado de forma manual, valendo-se do conhecimento geológico-geofísico e da experiência do intérprete, na avaliação visual dos padrões (características da curva do perfil representativa de um evento geológico) correspondentes a cada tipo litológico específico. O cálculo da porosidade efetiva combina tanto uma atividade visual, na identificação dos pontos representativos de uma particular rocha reservatório no perfil, como a escolha adequada da equação petrofísica que relaciona as propriedades físicas mensuradas da rocha com sua porosidade. A partir do conhecimento da porosidade, será estabelecido o volume eventualmente ocupado por hidrocarboneto. Esta atividade, essencial para a qualificação de reservatórios, requer muito do conhecimento e da experiência do intérprete de perfil para a efetiva avaliação da porosidade efetiva, ou seja, a porosidade da rocha reservatório, isenta do efeito da argila sobre a medida das propriedades físicas da mesma. Uma forma eficiente de automatizar estes procedimentos e auxiliar o geofísico de poço nestas atividades, que particularmente demandam grande dispêndio de tempo, é apresentado nesta dissertação, na forma de um novo perfil, derivado dos perfis tradicionais de porosidade, que apresenta diretamente o zoneamento. Pode-se destacar neste novo perfil as profundidades do topo e da base das rochas reservatório e das rochas selante, escalonado na forma de porosidade efetiva, denominado perfil de porosidade efetiva zoneado. A obtenção do perfil de porosidade efetiva zoneado é baseado no projeto e execução de várias arquiteturas de rede neural artificial, do tipo direta, com treinamento não supervisionado e contendo uma camada de neurônios artificiais, do tipo competitivo. Estas arquiteturas são projetadas de modo a simular o comportamento do intérprete de perfil, quando da utilização do gráfico densidade-neutrônico, para as situações de aplicabilidade do modelo arenito-folhelho. A aplicabilidade e limitações desta metodologia são avaliadas diretamente sobre dados reais, oriundos da bacia do Lago Maracaibo (Venezuela).

Fácies e associação de fácies da formação Pirambóia na região de Descalvado/SP

The Pirambóia Formation is a lithostratigraphic unit of the Paraná Basin, positioned between the Corumbataí (lower) and Botucatu (upper) Formations on the eastern edge of the basin. This unit is focused by many studies due to its great importance as an essential component in the Guarani Aquifer System (SAG) and the petroleum system “Irati-Pirambóia”, as excellent reservoirs. The Pirambóia Formation is historically the subject of several controversies on issues like age, contact relationships with the upper unit and depositional paleoenvironment. Despite these aspects, the Pirambóia Formation is commonly taken to be of Triassic age and is considered a product of wet aeolian systems, with plenty of wet interdunes and subordinate fluvial facies. In this work, by using techniques such as facies analysis, depositional architecture and facies association, facies of this unit were characterized and their depositional paleoenvironment was inferred particularly in Jundu Mining, region of Descalvado in northeastern São Paulo. Techniques such as grain size and petrographic analyses, aimed to characterize this unit as a potential reservoir rock. Five facies were described for the Pirambóia Formation in the studied region: St, Sh, Sm, Sr and Gt facies, generated by sedimentary processes of the bottom load type, mostly under low flow regime (with exception for the Sh facies, which is formed by upper flow regime processes). In addition to that, four facies associations were recognized from the architectural elements, primarily contained within the main channel: complex channel bars, composed by foreset macroforms (FM), sandy bedforms (SB) and gravel bars and bedforms (GB); flood deposits, constituted by laminated sand sheets (LS); deposits of hyperconcentrated flows and eolian deposits. It was interpreted that the Pirambóia Formation in Descalvado (SP) is the record of the sedimentation of braided rivers, with dunes and interdunes deposits...

Caracterização dos reservatórios do grupo Macaé no Campo de Garoupa - Bacia de Campos - por meio de interpretação sísmica e perfis de poço

The study area is the Garoupa Field, located 75 km from the coast of Rio de Janeiro in bathymetric elevation of 125 m and it is the first important offshore discovery of the Campos Basin with hydrocarbon production in the Albian carbonates. The high significance of carbonate rock reservoirs for the global oil industry and its degree of complexity, combined with the fact that the Garoupa Field is a mature field, make this research project interesting to develop a re-exploratory vision of the study area. The objective of this paper is to characterize the physical properties of the Macae Group reservoirs in the Garoupa Field through well correlation techniques, petrophysical analysis and seismic interpretation (3D), in order to evaluate qualitatively and quantitatively the response of geophysical data to the presence of carbonate rock reservoirs. From the analysis of well profiles (gamma ray, resistivity, density and sonic) it was possible to identify six reservoir levels in the Quissamã Formation. As a result, the reservoirs have good correlation between the wells in the Garoupa Field and show lateral facies variation. In the seismic interpretation, structural contour maps were generated in time (ms) from the top of the Macae Group and two horizons that correspond to the reservoir levels. These maps show that the oil producing area of this field is a structural high located at the west of the interpreted seismic cube, and it was classified as a rollover limited by lateral faults forming a horst. The seismic attribute maps show a good response to the reservoirs of the Garoupa Field because they are associated with amplitude anomalies, verified by the correlation between the physical properties of the reservoir rock and seismic data through cross plots, with emphasis in a linear correlation between the resistivity profile and the values of Maximum Absolute Amplitude and RMS Amplitude attributes

Caracterização da distribuição física dos dolomitos do membro Búzios no Campo de Badejo - Bacia de Campos

In the region of Badejo oil Ffeld (Campos Basin) lies an Lower Albian dolomitic layer that shows reservoir rock and seal conditions, among others and, it is occasionally karstified. This work applies geostatistical techniques of ordinary and indicatior kriging, in an attempt to determine a method that assists the analysis of different scenarios offered for petroleum drilling from a quantitative point of view this fact is justified, because there are different visions and strategies that would be adopted under different dolomite conditions (stable - low porosity and high density; reservoir - high porosity and medium density; instable - high porosity and low dentisty). The main objective is a methodological introduction that has not been tested in dolomites before aiming to characterize the distribution of the three conditions described above by ordinary and indicatior kriging, which was based on the obtained data from the dolomite layer identification through well logs interpretation and correlation, followed by seismic interpretation. In addition, it was generated structural contour maps, based on 2D and 3D seismic data interpretation, and then, seismic attributes maps were calculated, in order to transform them into pseudo-density maps, i.e., maps that correlate the density values with the attribute values. As primary results, structural contour maps and seismic attributes were obtained and ordinary and indicatior kriging maps were done, on which it is possible to interpret the distribution of the main reservoir and risk probability for drilling of exploration wells obtaining trends N35E and N10W direction for areas of stability or reservoir levels, while the central part of the map presents a higher risk for loss of drilling fluid. The cut-off values levels were based on the values of first and third quartiles of cumulative histogram (instable and stable zones, respectively), as well as the reservoir level was set as the interval...

Análise computacional de imagens de lâminas delgadas na predição dos parâmetros hidráulicos porosidade e condutividade hidráulica do aquífero Barreiras-RN

The understanding of the occurrence and flow of groundwater in the subsurface is of fundamental importance in the exploitation of water, just like knowledge of all associated hydrogeological context. These factors are primarily controlled by geometry of a certain pore system, given the nature of sedimentary aquifers. Thus, the microstructural characterization, as the interconnectivity of the system, it is essential to know the macro properties porosity and permeability of reservoir rock, in which can be done on a statistical characterization by twodimensional analysis. The latter is being held on a computing platform, using image thin sections of reservoir rock, allowing the prediction of the properties effective porosity and hydraulic conductivity. For Barreiras Aquifer to obtain such parameters derived primarily from the interpretation of tests of aquifers, a practice that usually involves a fairly complex logistics in terms of equipment and personnel required in addition to high cost of operation. Thus, the analysis and digital image processing is presented as an alternative tool for the characterization of hydraulic parameters, showing up as a practical and inexpensive method. This methodology is based on a flowchart work involving sampling, preparation of thin sections and their respective images, segmentation and geometric characterization, three-dimensional reconstruction and flow simulation. In this research, computational image analysis of thin sections of rocks has shown that aquifer storage coefficients ranging from 0,035 to 0,12 with an average of 0,076, while its hydrogeological substrate (associated with the top of the carbonate sequence outcropping not region) presents effective porosities of the order of 2%. For the transport regime, it is evidenced that the methodology presents results below of those found in the bibliographic data relating to hydraulic conductivity, mean values of 1,04 x10-6 m/s, with fluctuations between 2,94 x10-6 m/s and 3,61x10-8 m/s, probably due to the larger scale study and the heterogeneity of the medium studied.

Estudo da influência de sistemas microemulsionados na molhabilidade de arenitos e na recuperação avançada de petróleo

Sandstone-type reservoir rocks are commonly responsible for oil accumulation. The wettability is an important parameter for the physical properties of the container, since it interferes in characteristics such as relative permeability to the aqueous phase, residual oil distribution in the reservoir, operating characteristics with waterflood and recovery of crude oil. This study applied different types of microemulsion systems - MES - in sandstone reservoirs and evaluated their influences on wettability and residual oil recovery. For this purpose, four microemulsion were prepared by changing the nature of ionic surfactants (ionic and nonionic). Microemulsions could then be characterized by surface tension analysis, density, particle diameter and viscosity in the temperature range 30° C to 70° C. The studied oil was described as light and the sandstone rock was derived from the Botucatu formation. The study of the influence of microemulsion systems on sandstone wettability was performed by contact angle measurements using as parameters the rock treatment time with the MES and the time after the brine surface contact by checking the angle variation behavior. In the study results, the rock was initially wettable to oil and had its wettability changed to mixed wettability after treatment with MES, obtaining preference for water. Regarding rock-MES contact time, it was observed that the rock wettability changed more when the contact time between the surface and the microemulsion systems was longer. It was also noted only a significant reduction for the first 5 minutes of interaction between the treated surface and brine. The synthesized anionic surfactant, commercial cationic, commercial anionic and commercial nonionic microemulsion systems presented the best results, respectively. With regard to enhanced oil recovery performance, all systems showed a significant percentage of recovered oil, with the anionic systems presenting the best results. A percentage of 80% recovery was reached, confirming the wettability study results, which pointed the influence of this property on the interaction of fluids and reservoir rock, and the ability of microemulsion systems to perform enhanced oil recovery in sandstone reservoirs.

Estudo da influência de sistemas microemulsionados na molhabilidade de arenitos e na recuperação avançada de petróleo

Sandstone-type reservoir rocks are commonly responsible for oil accumulation. The wettability is an important parameter for the physical properties of the container, since it interferes in characteristics such as relative permeability to the aqueous phase, residual oil distribution in the reservoir, operating characteristics with waterflood and recovery of crude oil. This study applied different types of microemulsion systems - MES - in sandstone reservoirs and evaluated their influences on wettability and residual oil recovery. For this purpose, four microemulsion were prepared by changing the nature of ionic surfactants (ionic and nonionic). Microemulsions could then be characterized by surface tension analysis, density, particle diameter and viscosity in the temperature range 30° C to 70° C. The studied oil was described as light and the sandstone rock was derived from the Botucatu formation. The study of the influence of microemulsion systems on sandstone wettability was performed by contact angle measurements using as parameters the rock treatment time with the MES and the time after the brine surface contact by checking the angle variation behavior. In the study results, the rock was initially wettable to oil and had its wettability changed to mixed wettability after treatment with MES, obtaining preference for water. Regarding rock-MES contact time, it was observed that the rock wettability changed more when the contact time between the surface and the microemulsion systems was longer. It was also noted only a significant reduction for the first 5 minutes of interaction between the treated surface and brine. The synthesized anionic surfactant, commercial cationic, commercial anionic and commercial nonionic microemulsion systems presented the best results, respectively. With regard to enhanced oil recovery performance, all systems showed a significant percentage of recovered oil, with the anionic systems presenting the best results. A percentage of 80% recovery was reached, confirming the wettability study results, which pointed the influence of this property on the interaction of fluids and reservoir rock, and the ability of microemulsion systems to perform enhanced oil recovery in sandstone reservoirs.

Análise gráfica de estruturas porosas sobre a ótica da estereologia

In this work we developed a computer simulation program for physics porous structures based on programming language C + + using a Geforce 9600 GT with the PhysX chip, originally developed for video games. With this tool, the ability of physical interaction between simulated objects is enlarged, allowing to simulate a porous structure, for example, reservoir rocks and structures with high density. The initial procedure for developing the simulation is the construction of porous cubic structure consisting of spheres with a single size and with varying sizes. In addition, structures can also be simulated with various volume fractions. The results presented are divided into two parts: first, the ball shall be deemed as solid grains, ie the matrix phase represents the porosity, the second, the spheres are considered as pores. In this case the matrix phase represents the solid phase. The simulations in both cases are the same, but the simulated structures are intrinsically different. To validate the results presented by the program, simulations were performed by varying the amount of grain, the grain size distribution and void fraction in the structure. All results showed statistically reliable and consistent with those presented in the literature. The mean values and distributions of stereological parameters measured, such as intercept linear section of perimeter area, sectional area and mean free path are in agreement with the results obtained in the literature for the structures simulated. The results may help the understanding of real structures.

Wind Monitoring of the Saylorville and Red Rock Reservoir Bridges with Remote, Cellular-Based Notifications, May 2012

Following a high wind event on January 24, 2006, at least five people claimed to have seen or felt the superstructure of the Saylorville Reservoir Bridge in central Iowa moving both vertically and laterally. Since that time, the Iowa Department of Transportation (DOT) contracted with the Bridge Engineering Center at Iowa State University to design and install a monitoring system capable of providing notification of the occurrence of subsequent high wind events. In subsequent years, a similar system was installed on the Red Rock Reservoir Bridge to provide the same wind monitoring capabilities and notifications to the Iowa DOT. The objectives of the system development and implementation are to notify personnel when the wind speed reaches a predetermined threshold such that the bridge can be closed for the safety of the public, correlate structural response with wind-induced response, and gather historical wind data at these structures for future assessments. This report describes the two monitoring systems, their components, upgrades, functionality, and limitations, and results from one year of wind data collection at both bridges.