Avaliação da remoção de sedimentos pela operação de nivelamento de estradas florestais

The forest roads construction inevitably causes environmental impacts to adjacent ecosystems and streams. Also the routine activities of roads maintenance may similarly cause environmental impacts of about the same magnitude. The material scraped from the roadway by the motor grader is usually distributed along the roadsides, from where it may easily be washed out toward the streams. Therefore, quantifying the amount of sediments removed during road maintenance activities may provide important information of this stream sedimentation potential. For this purpose, three forest roads were divided in 30 m long segments, marked with leveled stakes. A nylon thread was then stretched across the leveled stakes and the distance from the nylon thread to the road surface was measured before and after the mechanical scraping of the road. The average removal of sediments was of 2,13 cm. Considering the mean density of soil 1,6 g cm -3, the average removal of sediments was of 341 t ha -1 of road. Considering still a 3,9 m wide and 150 m long road as an example, the total amount of removed sediments would be around 19,9 t. Road maintenance, therefore, must be well planned in order to avoid or minimize stream sedimentation.

A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

Diffusion of the synthetic pyrethroid permethrin into bed-sediments

Bed-sediments are a sink for many micro-organic contaminants in aquatic environments. The impact of toxic contaminants on benthic fauna often depends on their spatial distribution, and the fate of the parent compounds and their metabolites. The distribution of a synthetic pyrethroid, permethrin, a compound known to be toxic to aquatic invertebrates, was studied using river bed-sediments in lotic flume channels. trans/cis-Permethrin diagnostic ratios were used to quantify the photoisomerization of the trans isomer in water. Rates were affected by the presence of sediment particles and colloids when compared to distilled water alone. Two experiments in dark/light conditions with replicate channels were undertaken using natural sediment, previously contaminated with permethrin, to examine the effect of the growth of an algal biofilm at the sediment-water interface on diffusive fluxes of permethrin into the sediment. After 42 days, the bulk water was removed, allowing a fine sectioning of the sediment bed (i.e., every mm down to 5 mm and then 5-10 mm, then every 10 mm down to 50 mm). Permethrin was detected in all cases down to a depth of 5-10 mm, in agreement with estimates by the Millington and Quirk model, and measurements of concentrations in pore water produced a distribution coefficient (K-d) for each section, High K-d's were observed for the top layers, mainly as a result of high organic matter and specific surface area. Concentrations in the algal biofilm measured at the end of the experiment under light conditions, and increases in concentration in the top 1 mm of the sediment, demonstrated that algal/bacterial biofilm material was responsible for high K-d's at the sediment surface, and for the retardation of permethrin diffusion. This specific partition of permethrin to fine sediment particles and algae may enhance its threat to benthic invertebrates. In addition,the analysis of trans/cis-permethrin isomer ratios in sediment showed greater losses of trans-permethrin in the experiment under light conditions, which may have also resulted from enhanced biological activity at the sediment surface.

A preliminary investigation of the release of oil from contaminated clays and other fine-grained sediments during consolidation

Fine-grained sediments on land, or in a freshwater or marine environment, may become contaminated with a wide range of pollutants including hydrocarbons. This paper is concerned with preliminary studies of the mobilization and transportation of hydrocarbons, during the process of consolidation, to adjacent sediments or water bodies. A modified Rowe Cell was used to measure the consolidation properties of prepared kaolinite and bentonite clay-water slurries, with and without the addition of oil, along with hydrocarbon-bearing drill-cuttings samples taken from the sea-bed adjacent to two North Sea oil-well platforms. The consolidation properties of the kaolinite and bentonite clay slurries were little altered by the addition of oil, which was present at concentrations of between 8073 and 59 572 mg kg(-1). During each consolidation stage, samples of the expelled pore-fluids were collected and analysed for oil content. These values were very low in comparison with the original oil concentration in the samples and changed little between each consolidation stage. Analysis of the slurry samples both before and after consolidation confirms that, proportionally, little oil is removed as a result of consolidation. The implication of these results is that, for the range of samples tested, the very high hydraulic gradients and particle rearrangements that occur during the process of consolidation are capable of releasing only proportionally small amounts of oil bound to the fine-grained clay and silt particles.

Analysis of wall plasters and natural sediments from the Neolithic town of Çatalhöyük (Turkey) by a range of analytical techniques

Wall plaster sequences from the Neolithic town of Çatalhöyük have been analysed and compared to three types of natural sediment found in the vicinity of the site, using a range of analytical techniques. Block samples containing the plaster sequences were removed from the walls of several different buildings on the East Mound. Sub-samples were examined by IR spectroscopy, X-ray diffraction and X-ray fluorescence to determine the overall mineralogical and elemental composition, whilst thin sections were studied using optical polarising microscopy, IR Microscopy and Environmental Scanning Electron Microscopy with Energy Dispersive X-ray analysis. The results of this study have shown that there are two types of wall plaster found in the sequences and that the sediments used to produce these were obtained from at least two distinct sources. In particular, the presence of clay, calcite and magnesian calcite in the foundation plasters suggested that these were prepared predominantly from a marl source. On the other hand, the finishing plasters were found to contain dolomite with a small amount of clay and no calcite, revealing that softlime was used in their preparation. Whilst marl is located directly below and around Çatalhöyük, the nearest source of softlime is 6.5 km away, an indication that the latter was important to the Neolithic people, possibly due to the whiter colour (5Y 8/1) of this sediment. Furthermore, the same two plaster types were found on each wall of Building 49, the main building studied in this research, and in all five buildings investigated, suggesting that the use of these sources was an established practice for the inhabitants of several different households across the site.

A new genus of Ectinosomatidae (Copepoda, Harpacticoida) from sublittoral sediments in Ubatuba, Sao Paulo State (Brazil), an updated key to genera and notes on Noodtiella Wells, 1965

Both sexes of a new genus and species of Ectinosomatidae (Copepoda, Harpacticoida) from sublittoral sediments collected on the inner continental shelf in Ubatuba, Sao Paulo State (Brazil) are described in detail. Chaulionyx gen. n. (type species: C. paivacarvalhoi sp. n.) differs from all known genera in the presence of a conspicuous bifid spine on the prehensile P1 endopod. It can be differentiated from other genera with a prehensile endopod (Halophytophilus Brian, 1919; Bradyellopsis Brian, 1925; Klieosoma Hicks & Schriever, 1985) by the presence of distinctive subrectangular middorsal pores on the urosomites and the unarmed male sixth legs. The genus Lineosoma Wells, 1965 is recognized as a paraphyletic taxon and relegated to a junior subjective synonym of Noodtiella Wells, 1965. Arenosetella pectinata Chappuis, 1954a is removed from its floating position in Ectinosomoides Nicholls, 1945, transferred to the genus Noodtiella as N. pectinata comb. n. and considered the senior subjective synonym of N. toukae Mitwally & Montagna, 2001. Dichotomous keys are provided for the identification of the 18 valid species of Noodtiella and the 21 valid genera of the family Ectinosomatidae. Halophytophilus aberrans Wells & Rao, 1987 is placed species incertae sedis in the family.

A 2400-year record of trace metal loading in lake sediments of Lagoa Vermelha, southeastern Brazil

Sediments of the Lagoa Vermelha (Red Lake), situated in the Ribeira Valley, southeastern Brazil, are made of a homogeneous, organic-rich, black clay with no visible sedimentary structures. The inorganic geochemical record (Al, As, Ba, Br, Co,Cs, Cr, Fe, Mn, Ni, Rb, Sc, Sb, V, Zn, Hg and Pb) of the lake sediments was analyzed in a core spanning 2430 years. The largest temporal changes in trace metal contents occurred approximately within the last 180 years. Recent sediments were found to be enriched in Pb, Zn, Hg, Ni, Mn, Br and Sb (more than 2-fold increase with respect to the "natural background level"). The enhanced accumulation of Br, Sb, and Mn was attributed to biogeochemical processes and diagenesis. On the other hand, the anomalous concentrations of Pb, Zn, Hg and Ni were attributed to pollution. As Lagoa Vermelha is located in a relatively pristine area, far removed from direct contamination sources, the increased metal contents of surface sediments most likely resulted from atmospheric fallout. Stable Pb isotopes provided additional evidence for anthropogenic contamination. The shift of Pb-206/Pb-207 ratios toward decreasing values in the increasingly younger sediments is consistent with an increasing contribution of airborne anthropogenic lead. In the uppermost sediments (0-10 cm), the lowest values of the Pb-206/Pb-207 ratios may reflect the influence of the less radiogenic Pb from the Ribeira Valley District ores (Pb-206/Pb-207 between 1.04 and 1.10), emitted during the last 50 years. (C) 2011 Elsevier Ltd. All rights reserved.

Calcium nitrate addition to control the internal load of phosphorus from sediments of a tropical eutrophic reservoir: Microcosm experiments

The main objective of this study was to perform laboratory experiments on calcium nitrate addition to sediments of a tropical eutrophic urban reservoir (Ibirite reservoir, SE Brazil) to immobilize the reactive soluble phosphorus (RSP) and to evaluate possible geochemical changes and toxic effects caused by this treatment. Reductions of 75 and 89% in the concentration of RSP were observed in the water column and interstitial water, respectively, after 145 days of nitrate addition. The nitrate application increased the rate of autotrophic denitrification, causing a consumption of 98% of the added nitrate and oxidation of 99% of the acid volatile sulfide. As a consequence, there were increases in the sulfate and iron (II) concentrations in the sediment interstitial water and water column, as well as changes in the copper speciation in the sediments. Toxicity tests initially indicated that the high concentrations of nitrate and nitrite in the sediment interstitial water (up to 2300 mg L-1 and 260 mg L-1, respectively) were the major cause of mortality of Ceriodaphnia silvestrii and Chironomus xanthus. However, at the end of the experiment, the sediment toxicity was completely removed and a reduction in the 48 h-EC50 of the water was also observed. Based on these results we can say that calcium nitrate treatment proved to be a valuable tool in remediation of eutrophic aquatic ecosystems leading to conditions that can support a great diversity of organisms after a restoration period. (C) 2012 Elsevier Ltd. All rights reserved.

Reconnaissance survey of Galveston Bay sediments for selective nonresidual trace metals

The nonresidual concentrations of five trace metals were determined for 322 sediments that were the product of a systematic sampling program of the entire Galveston Bay system. The nonresidual component of the trace metal concentration (e.g. that fraction of the metals that can be relatively easily removed from the sediments without complete destruction of the sediment particle) was considered to be more indicative of the anthropogenic metal pollution that has impacted the Galveston Bay ecosystem.^ For spatial analysis of the metal concentrations, the Galveston Bay system was divided into nine bay-areas, based on easily definable geological and geographical characteristics. Isopleth mapping analyses of these metal concentrations indicated a direct relationship with the $<$63$\mu$m fraction of the sediment (%FINE) in all of the bay areas. Covariate regression analyses indicated that position of the sediment within the Galveston Bay system (e.g. bay-area) was a better predictor of metal concentration than %FINE. Analysis of variance of the metals versus the bay-areas indicated that the five metals maintained a relatively constant order and magnitude of concentration for all the bay-areas.^ The major shipping channels of the Galveston Bay system, with their associated vessels and transported materials, are a likely source of metal pollution. However, these channels were not depositional corridors of high metal concentration. All metal concentration highs were found to be located away from the channels and associated with %FINE highs in the deeper portions of the bay-areas.^ Disturbance of the sediments, by the proposed widening and deepening of these channels, is not predicted to remobilize the trace metals. A more likely adverse effect on the health of the Galveston Bay ecosystem would come from the increase in turbidity of the water due to the dredging and in an extension of the salt water wedge farther north into the bay system. ^

Index properties, shear strenghts and consolidation characteristics of ODP Hole 164-995A sediments

Geotechnical properties of sediment from Ocean Drilling Program Leg 164 are presented as: (1) normalized shipboard strength ratios from the Cape Fear Diapir, the Blake Ridge Diapir, and the Blake Ridge; and (2) Atterberg limit, vane shear strength, pocket-penetrometer strength, and constant-rate-of-strain consolidation results from Hole 995A, located on the Blake Ridge. This study was conducted to understand the stress history in a region characterized by high sedimentation rates and the presence of gas hydrates. Collectively, the results indicate that sediment from the Blake Ridge exhibits significant underconsolidated behavior, except near the seafloor. At least 10 m of additional overburden was removed by erosion or mass wasting at Hole 993A on the Cape Fear Diapir, compared to nearby sites.

Quantitative component analysis of the coarse fraction of surface sediments from the Persian Gulf

In the Persian Gulf and the Gulf of Oman marl forms the primary sediment cover, particularly on the Iranian side. A detailed quantitative description of the sediment components > 63 µ has been attempted in order to establish the regional distribution of the most important constituents as well as the criteria governing marl sedimentation in general. During the course of the analysis, the sand fraction from about 160 bottom-surface samples was split into 5 phi° fractions and 500 to 800 grains were counted in each individual fraction. The grains were cataloged in up to 40 grain type catagories. The gravel fraction was counted separately and the values calculated as weight percent. Basic for understanding the mode of formation of the marl sediment is the "rule" of independent availability of component groups. It states that the sedimentation of different component groups takes place independently, and that variation in the quantity of one component is independent of the presence or absence of other components. This means, for example, that different grain size spectrums are not necessarily developed through transport sorting. In the Persian Gulf they are more likely the result of differences in the amount of clay-rich fine sediment brought in to the restricted mouth areas of the Iranian rivers. These local increases in clayey sediment dilute the autochthonous, for the most part carbonate, coarse fraction. This also explains the frequent facies changes from carbonate to clayey marl. The main constituent groups of the coarse fraction are faecal pellets and lumps, the non carbonate mineral components, the Pleistocene relict sediment, the benthonic biogene components and the plankton. Faecal pellets and lumps are formed through grain size transformation of fine sediment. Higher percentages of these components can be correlated to large amounts of fine sediment and organic C. No discernable change takes place in carbonate minerals as a result of digestion and faecal pellet formation. The non-carbonate sand components originate from several unrelated sources and can be distinguished by their different grain size spectrum; as well as by other characteristics. The Iranian rivers supply the greatest amounts (well sorted fine sand). Their quantitative variations can be used to trace fine sediment transport directions. Similar mineral maxima in the sediment of the Gulf of Oman mark the path of the Persian Gulf outflow water. Far out from the coast, the basin bottoms in places contain abundant relict minerals (poorly sorted medium sand) and localized areas of reworked salt dome material (medium sand to gravel). Wind transport produces only a minimal "background value" of mineral components (very fine sand). Biogenic and non-biogenic relict sediments can be placed in separate component groups with the help of several petrographic criteria. Part of the relict sediment (well sorted fine sand) is allochthonous and was derived from the terrigenous sediment of river mouths. The main part (coarse, poorly sorted sediment), however, was derived from the late Pleistocene and forms a quasi-autochthonous cover over wide areas which receive little recent sedimentation. Bioturbation results in a mixing of the relict sediment with the overlying younger sediment. Resulting vertical sediment displacement of more than 2.5 m has been observed. This vertical mixing of relict sediment is also partially responsible for the present day grain size anomalies (coarse sediment in deep water) found in the Persian Gulf. The mainly aragonitic components forming the relict sediment show a finely subdivided facies pattern reflecting the paleogeography of carbonate tidal flats dating from the post Pleistocene transgression. Standstill periods are reflected at 110 -125m (shelf break), 64-61 m and 53-41 m (e.g. coare grained quartz and oolite concentrations), and at 25-30m. Comparing these depths to similar occurrences on other shelf regions (e. g. Timor Sea) leads to the conclusion that at this time minimal tectonic activity was taking place in the Persian Gulf. The Pleistocene climate, as evidenced by the absence of Iranian river sediment, was probably drier than the present day Persian Gulf climate. Foremost among the benthonic biogene components are the foraminifera and mollusks. When a ratio is set up between the two, it can be seen that each group is very sensitive to bottom type, i.e., the production of benthonic mollusca increases when a stable (hard) bottom is present whereas the foraminifera favour a soft bottom. In this way, regardless of the grain size, areas with high and low rates of recent sedimentation can be sharply defined. The almost complete absence of mollusks in water deeper than 200 to 300 m gives a rough sedimentologic water depth indicator. The sum of the benthonic foraminifera and mollusca was used as a relative constant reference value for the investigation of many other sediment components. The ratio between arenaceous foraminifera and those with carbonate shells shows a direct relationship to the amount of coarse grained material in the sediment as the frequence of arenaceous foraminifera depends heavily on the availability of sand grains. The nearness of "open" coasts (Iranian river mouths) is directly reflected in the high percentage of plant remains, and indirectly by the increased numbers of ostracods and vertebrates. Plant fragments do not reach their ultimate point of deposition in a free swimming state, but are transported along with the remainder of the terrigenous fine sediment. The echinoderms (mainly echinoids in the West Basin and ophiuroids in the Central Basin) attain their maximum development at the greatest depth reached by the action of the largest waves. This depth varies, depending on the exposure of the slope to the waves, between 12 to 14 and 30 to 35 m. Corals and bryozoans have proved to be good indicators of stable unchanging bottom conditions. Although bryozoans and alcyonarian spiculae are independent of water depth, scleractinians thrive only above 25 to 30 m. The beginning of recent reef growth (restricted by low winter temperatures) was seen only in one single area - on a shoal under 16 m of water. The coarse plankton fraction was studied primarily through the use of a plankton-benthos ratio. The increase in planktonic foraminifera with increasing water depth is here heavily masked by the "Adjacent sea effect" of the Persian Gulf: for the most part the foraminifera have drifted in from the Gulf of Oman. In contrast, the planktonic mollusks are able to colonize the entire Persian Gulf water body. Their amount in the plankton-benthos ratio always increases with water depth and thereby gives a reliable picture of local water depth variations. This holds true to a depth of around 400 m (corresponding to 80-90 % plankton). This water depth effect can be removed by graphical analysis, allowing the percentage of planktonic mollusks per total sample to be used as a reference base for relative sedimentation rate (sedimentation index). These values vary between 1 and > 1000 and thereby agree well with all the other lines of evidence. The "pteropod ooze" facies is then markedly dependent on the sedimentation rate and can theoretically develop at any depth greater than 65 m (proven at 80 m). It should certainly no longer be thought of as "deep sea" sediment. Based on the component distribution diagrams, grain size and carbonate content, the sediments of the Persian Gulf and the Gulf of Oman can be grouped into 5 provisional facies divisions (Chapt.19). Particularly noteworthy among these are first, the fine grained clayey marl facies occupying the 9 narrow outflow areas of rivers, and second, the coarse grained, high-carbonate marl facies rich in relict sediment which covers wide sediment-poor areas of the basin bottoms. Sediment transport is for the most part restricted to grain sizes < 150 µ and in shallow water is largely coast-parallel due to wave action at times supplemented by tidal currents. Below the wave base gravity transport prevails. The only current capable of moving sediment is the Persian Gulf outflow water in the Gulf of Oman.

Sedimentary mineralogy of argillaceous sediments at DSDP Legs 56-57 Holes

Mineral assemblages of DSDP Holes 436 and 438A and the upper section of Hole 439 (871.5-911.0 m sub-bottom) resemble each other and are composed of montmorillonite (probably a small portion of montmorillonite/illite mixed-layer clays), illite, chlorite, kaolinite, quartz, plagioclase, hornblende, calcite, dolomite, siderite, gypsum, pyrite, and halite. In the middle section of Hole 439 (933.5-1041.0 m), clinoptilolite is also found. In the lower section of Hole 439 (1077.5-1150.0 m), montmorillonite is not confirmed, and clinoptilolite and mixed-layer illite are found. These assemblages, which also contain detrital kaolinite, are generally found in sediments from brackish-water environments. At Site 439, more than 1000 meters of sediment might have been removed by erosion at the base.

Geotechnical properties of sediments at DSDP Leg 84 Holes

The geotechnical characteristics of 22 sediment samples from Leg 84 sites were studied in an effort to associate these with processes active along the Middle America slope and with sedimentation mechanisms. Geotechnical properties measured include water content, porosity, bulk density, Atterberg limits, consolidation characteristics, permeability, and vane shear strength. A majority of samples obtained from Sites 565, 568, and 570 show significant disturbance resulting from degassing. This disturbance apparently results in underconsolidation, although other mechanisms such as excess pore pressures generated from the subduction process can also contribute to this state. Overconsolidated sediments were found at Sites 565, 566, and 569. The overconsolidated sediments at Sites 565 and 569 may result from downslope transport mechanisms rearranging and stressing the sediment mass under consideration. The sediment condition at Site 566 is probably a result of eroded overburden: an estimated 87 m of overlying sediments may have been removed. Geotechnical and permeability relationships with depth are consistent with those found for other hemipelagic sediments of silty clay to clayey silt textures.

Magnetic properties of basalts and sediments of ODP Leg 135 sites

Paleomagnetic and rock-magnetic investigations of basalts from Hole 834B in the Lau backarc basin and of sediments from Holes 841A and 841B at the Tonga Ridge are reported. Three groups of blocking temperatures in the basalts suggest the presence of at least three magnetic phases: pure magnetite, a Ti-poor titanomagnetite, and a Ti-rich phase. The drill-string-induced remanence in the basalts is typically between three and six times the original normal remanent magnetization intensity, but it is mostly removed by alternating-field (AF) cleaning in 5 mT. Volume susceptibility values range from 0.04 * 10**-3 to 4 * 10**-3 cgs. The modified Q-ratio J5/sus ranges from 0.5 to 10. The drill-string-induced remanence behaves different in the two sediment cores from Holes 841A and 841B, which may be the result of differences in the sediment or caused by the different drilling equipment used. The AF-cleaned inclinations of the sediment in Holes 841A and 841B suggest a slight flattening with increasing depth (up to 6° under a load of 400 m of sediment) to be present. This flattening is likely to be caused by the differential rotation of detrital particles under compaction during diagenesis.

Helium concentrations of late Miocene sediments

Throughout the history of the Solar System, Earth has been bombarded by interplanetary dust particles (IDPs), which are asteroid and comet fragments of diameter 1-1,000 µm. The IDP flux is believed to be in quasi-steady state: particles created by episodic main belt collisions or cometary fragmentation replace those removed by comminution, dynamical ejection, and planetary or solar impact. Because IDPs are rich in 3He, seafloor sediment 3He concentrations provide a unique means of probing the major events that have affected the IDP flux and its source bodies over geological timescales (Farley et al., 1998, doi:10.1126/science.280.5367.1250; Takayanagi and Ozima, 1987, doi:10.1029/JB092iB12p12531; Farley, 1995, doi:10.1038/376153a0; Kortenkamp and Dermott, 1998, doi:10.1126/science.280.5365.874). Here we report that collisional disruption of the >150-km-diameter asteroid that created the Veritas family 8.3 +/- 0.5 Myr ago (Nesvorny et al., 2003, doi:10.1086/374807) also produced a transient increase in the flux of interplanetary dust-derived 3He. The increase began at 8.2 +/- 0.1 Myr ago, reached a maximum of 4 times pre-event levels, and dissipated over 1.5 Myr. The terrestrial IDP accretion rate was overwhelmingly dominated by Veritas family fragments during the late Miocene. No other event of this magnitude over the past 10**8 yr has been deduced from main belt asteroid orbits. One remarkably similar event is present in the 3He record 35 Myr ago, but its origin by comet shower (Farley et al., 1998, doi:10.1126/science.280.5367.1250) or asteroid collision (Tagle and Claeys, 2004, doi:10.1126/science.1098481) remains uncertain.