Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace

Uma narrativa pré-histórica: o cotidiano de antigos grupos humanos no sertão do Seridó/RN

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Planejamento dos recursos hídricos da bacia hidrográfica do rio Seridó, no Rio Grande do Norte

The present research has the purpose of planning the management of the water resources of the Seridó River watershed, in the state of Rio Grande do Norte, Brazil. It has an emphasis on the amount of surface water available in this region, to provide a sustainable water supply. Based on data and information collected from public departments responsible for the management of the water resources of the Rio Grande do Norte state, well as on researches related to water resources , a watershed balance was done, and the results suggested the transposition of the waters from the Piranhas-Açu river watershed taken from the Oiticica and Armando Ribeiro Gonçalves reservoirs, integrated with the construction of 2 hidroelectrical plants and 2 elevation stations, to pump the amount of water needed to the expected demand in some public dams of the region until 2020. So, with the use of the surface water potential that exists in the region, it was demonstrated that, on the contrary of the public policies implemented in the past and in the current by the federal and state realm, it is possible to supply the currently water demands and also the future ones, in a sustainable way, without the need of importing outter water to the respective watershed. Finally, it was proposed the implementation of the Water Resources Plan in the Seridó region WRPS, aiming at providing an auto-sustainable development by significantly diminishing the effects of the dry seasons in that region, by considering the economic, social and environmental sustainability

Circuitos espaciais de produção da atividade boneleira: o uso dos territórios de Caicó, Serra Negra do Norte e São José do Seridó

Cette étude a été fondée sur la reconaissance, la description et l'analyse du circuit spatial de la production de l activité des fabriques des casquettes dans la région du Seridó Potiguar. L activité des fabriques des casquettes est située dans les villes de Caicó, Serra Negra do Norte e São José do Seridó, qui forment le pôle de fabriques de casquettes, composé de soixante-quatre (64) unités de fabrication, le deuxième plus grand producteur de casquettes au Brésil. Dans la condition de base géographique, l'opérationnalisation du concept de circuits spatiales de la production a été essentielle à la compréhension de l'utilisation du territoire et de l'indivisibilité de l'espace, du fournisseur de matières premières au consommateur final, comprenant les étapes des matières premières, la main-d'oeuvre, le stockage, les transports, le commerce et la consommation dans la période actuelle, dans laquelle les instances de la production, la circulation, la distribution et de la consommation sont spatialement diffus. Sur la base de l'identification et de la localisation de ces étapes et des principaux acteurs impliqués dans la activité des fabriques de casquettes, une configuration de circuit spatial de la production a été élaborée, en s'interprétant l'utilisation des territoires par les instances productives. L'interprétation des étapes de production a identifié que les entreprises liées à l'Association Seridoense des Fabricants de Casquettes agissent plus efficacement sur le territoire que celles nonassociées, alors que toujours elles investissent dans des nouveaux équipements, en augmentant sa puissance technique pour se renforcer avant un marché si compétitif comme celui des casquettes. En examinant la contribution de la fabrication des casquettes à l'utilisation actuelle des territoires de la coupe, nous avons appris que les activités complémentaires et des matières premiéres nécessaires à sa réalisation se trouvent dans leur environnement géographique. Ainsi, la proximité spatiale entre les étapes de la fabrication des casquettes fait entrevoir la matérialité du territoire, conférée dans la coexistence des techniques passées et présentes, et l'ensemble des actions effectuées par un certain nombre de travailleurs sociaux qui collaborent à la création du circuit spatial de la production de l activité des fabriques des casquettes. Cette étude a confirmé que les fabriques des casquettes sont organisées sous la forme de cellules de production, continues ou discontinues, dont les équipements et les machines à coudre industrielles obéissent à la logique d'une production de plus en plus standardisée. Ce circuit spatial de la production contribue à l'utilisation actuelle des territoires de Caicó, Serra Negra do Norte et de São José do Seridó car il amplifie le mouvement du commerce et des relations entre les lieux, à travers la dynamique des flux des personnes, des biens et des produits, en constante circulation, guidées par la division du travail entre les étapes productives

O Litoral e a metrópole dinâmica imobiliária, turismo e expansão urbana na região metropolitana de Natal-RN

The metropolitan regions of Northeast Brazil are being gradually included in a scenario of international investments, which are motivated by the restructuring of both touristic and real-estate sectors. The new capital, real-estate developers and space configurations that result from this process indicate the need for the creation and implementation of public tools which should, at least, allow the mitigation of the urban impacts and environmental losses resulting from this situation. The effects on landscape and on the socio-spatial configuration result from the intensification caused by the dynamism of the "real estate-tourism" sector. There is a regional integration as an expression of the urban expansion of the metropolitan area of Natal. This study investigates the uniqueness of the restructuring and territorial integration of coastal areas and the strategies of the circuit of capital accumulation formed by linking the real estate to tourism. It is intended to increase the understanding about the strategies of tourism, real estate and public policy agents involved in this territorial reconfiguration and in the fund-raising needed for the investments, to understand the existing social and environmental effects and their future trends and also to understand the forms of spatial production as results from the practices of approaching the land transformation and the tourism valorization of the landscape, in a synchronous manner, first in the Northeast region and, as a focal study, in the Metropolitan Area of Natal. Likewise, it is intended to apprehend the current processes of metropolization of the eastern coast of Rio Grande do Norte, in addition to indicate its physical-territorial transformation and the types of projects/developments promoted by the market in the recent period. Based upon analysis undertaken for the Metropolitan Region of Natal RN, this piece of work presents some considerations on possible legal instruments that can be adjusted to the municipalities which are experiencing the impact of this peculiar and recent phenomenon in the region, caused by the arrival of the real estate-touristic capital. It is also intended to point out basic proposals to the forms of public intervention, in a speculative way, starting from a Metropolitan Planning project within a medium and long term

O terciário (re) desenhando a periferia: a região administrativa norte de Natal/RN, na última década do século XX, servicializada na Av. Dr. João Medeiros Filho

The tertiary sector has been (re)defining and (re)qualifying, in an impacting way, the urban spaces in the cities, introducing new elements for the discussion of the relationship center/periphery. In Natal, as an inducing economic activity of its development, it conforms to the new needs of the capital, expanding, being materialized through several processes and spatial forms. We aim at analyzing one of those processes, which has taken its Northern Administrative Area to (re)define the design of its urban space, through the actions developed by the agents involved with the spatialization of the tertiary activities, at the same time as it redimensions its role as a periphery of Natal, contributing to the study of the recent and growing transformations of the Brazilian capitals. The studied district corresponds to 39.4% of the municipal area and, until recently, was composed by precarious reproduction spaces, unprovided of relevant economical activities. After the boom of the development of extensive housing complexes by SFH/BNH, the area, gradually stopped being a dependent area, and it imposed itself as an economically participant region, with the increase of the trade and services sectors, as well as a favorable place for the appearance of new activities. Its reflexes are noticeable in the achieved spatial configuration. As the main road to induct changes, Dr. João Medeiros Filho Avenue presents these new tendencies in the production of the intraurban space, concentrating the largest goods and services equipments of the area, through investments of the private and public sectors, which guarantee the capital allocation for the construction of a new centrality

Eutrofização e capacidade de carga de fósforo de seis reservatórios a bacia do Rio Seridó, região semi-árida do Estado do RN

The eutrofization is a natural process of accumulation of nutrients in aquatic´s body that it has been accelerated for the human´s actives, mainly the related with the activities of camp, industrial and the inadequate disposition of the domestic sewage. The enrichment of the aquatic´s body with nutrients, mainly the nitrogen and the phosphorus, and the consequent proliferation of algae and Cyanobacteria can commit the quality of the water for the public provisioning, for the fish farming and for other ends. The problem becomes more critical when there is a shortage of water naturally as in the semi-arid area of the Brazilian northeast. Before that problem this work had as objective evaluates the trophic state of six reservoirs of the basin of River Seridó of Rio Grande of Norte and also estimate the capacity of load of match of the reservoir and risk probabilities based on the established limits by the resolution Conama 357/05. The results demonstrate that the six reservoirs are eutrofization, with concentration of total phosphorus and cloro a in the water upster to 50 e 12 μg l-1. The results show that space homogeneity exists in the state trophic of the reservoirs, but a significant variation interanual in function of the increase of the concentrations of nutrients and decrease of the transparency of the water with the reduction of the body of water accumulated in the reservoirs.The results of the simulation risk estocastic show that the reservoirs could receive annually from 72 to 216 Kg of P, assuming a risk of 10% of increasing in more than 30 μg l-1 the annual medium concentrations of total match in the water of these reservoirs. This load could be high in until 360 kg of P a year in case the managers assume a risk of 10% of increasing in more than 50 μg l-1 the annual medium concentrations of total phosphorus in the waters of these reservoirs

Avaliação da ecotoxicidade de percolados em áreas de disposição de resíduos na região metropolitana de Natal/RN

Leachates are effluent produced by decomposition of solid waste, they have complex composition and can be highly toxic. Therefore such percolated liquid should be collected and treated properly to avoid environmental contamination of soil and of water bodies. The objective of this study was to evaluate the toxicity through ecotoxicological tests with Ceriodaphnia dubia (Cladocera - Crustacea) of percolated liquids generated in two different systems of municipal solid waste (MSW) disposal in the city of Natal/ RN: A Sanitary Landfill in the Metropolitan Region of Natal/ RN, and in a dump off area. Furthermore, it was evaluated the possible contamination of the underground water of the dump off area. Two monthly samples were taken at four points between the months of May/2009 and January/2010. The Point "A" corresponds to the end of the pond leachate treatment in ASRMN; The Point "B" corresponds to a containment pond at the dump. The Point "C" is an area near one of the cells of the dump off area where the leachate outcrops; The Point "D" stands for an underground water well at the area. The last point, called "E" was sampled only once and corresponds to the slurry produced by temporary accumulation of solid waste in the open area of the dump. The ecotoxicological tests, acute and chronic, followed the ABNT 13373/2005 rules, with some modifications. The samples were characterized by measuring the pH number, the dissolved oxygen (DO), the salinity, BOD5, COD, Cd, Cu, Pb, Cr, Fe, Mg, Ni, and Zn. At Point A, the average number of EC50-48h ranged between 1.0% and 2.77% (v/v), showing a high toxicity of the leachate to C.dubia in all months. To this point, positive correlations were found between the EC50- 48 with precipitation. Negative correlations were found between the EC50- 48h with salinity. At point B there was no response of the acute exposure of organisms to the test samples. At point C the EC50-48h ranged from 17.68% to 35.36% in just two months of the five ones analyzed, not correlated meaning. Point D, the EC50-48h level ranged between 12.31% and 71.27%, showed a negative correlation with, only, precipitation. Although it was observed toxicity of underground water in the Landfill Area, there was no evidence of water contamination by leachate, however, due to the toxic character of this water, additional tests should be conducted to confirm the quality of water that is used for human supply. At point E there was no acute toxicity. These results support the dangers of inappropriate disposal of MSW to water bodies due to the high toxicity of the leachate produced highlighting the necessity of places of safe confinement and a treatment system more effective to it

Uso de resíduo e de minerais de pegmatito da região do seridó RN e de argilas portuguesas em formulações de grês porcelanato

In the State Rio Grande do Norte, Brazil, the most significant deposits of minerals in the production of granite and pegmatite are Seridó region. Municipalities of Parelhas and Equador are the main responsible for the production of feldspar, quartz, kaolin and granite. The ceramic industries are always in search of competitiveness by investing in new products or improving existing techniques. The stoneware is a type of pottery that stands in the market because it presents technical and aesthetic characteristics superior to other existing products. Characteristics of the raw materials initially obtained with chemical analysis and mineralogical analysis are crucial in getting a product that satisfies the conditions in a manufacturing process and is, in principle, directly related to the firing cycle. This research aimed at developing new formulations for the mass production of ceramic stoneware. The raw materials initially characterized were feldspar, quartz, kaolin and granite. As part of the research was developed at the University of Aveiro, in Portugal, we used two clays used in the production of Portuguese ceramics. The raw material Brazilian and Portuguese and the final product, both in Portugal and Brazil, were analyzed for X-ray fluorescence, X-ray diffraction, granulometric analysis, dilatometric analysis, thermal analysis and analysis of scanning electron microscopy (MEV). The specimens prepared at the University of Aveiro (DECV) were sintered at 10000C and 12000C and the specimens prepared in UFRN were sintered at 10000C, 10500C, 11000C, 11500C, 12000C, 12500C and 13000C, but the best results and demonstrating the presence of the mineral mullite were at temperatures of 12000C, 12500C and 13000C. The results showed that the granite waste used may be considered raw material of excellent quality for use in the ceramic industry and coating floors and more accurately by the industry of stoneware. Physical and mechanical tests conducted on samples of the formulations F01 and F02 developed in UFRN showed a water absorption and mechanical strength suitable for the stoneware

Diagnóstico da possível influência da atividade petrolífera em sedimentos de fundo da Bacia Piranhas-Açu, região Baixo Açu/RN

It is located in an area of increasing oil exploration, the region of the Lower Açu is at the mercy of a possible pollution generated by this economic activity, which includes various chemical substances harmful to health, such as metals. This thesis aims to, diagnose the areas of River Piranhas-Açu, a region of the Lower Açu, which are polluted by traces factors and more. In this study, it was determined the concentration of the chemica elements Al, CD, Cr, Cu, Fe, Mn, Ni, P, Pb, V and Zn, through the technique of ICP-OES analysis and the size of sediments and their contents organic matter. Were mapped by GPS, 12 points from collections. The interpretations of the results, together associating that allowed pollution to a possible contamination by oil activity. The results showed tha some regions have low concentrations of cadmium, lead, copper, manganese and zinc unable to promote damage to human health. However, there are places where the concentrations of certain metals chromium, iron and zinc are moderately polluted compared to the results with the reference values of literature and others that are highly polluted by iron. However, due to a greater number of wells in production in those locations, those higher concentrations, it can be suggested a possible influence of oi production in some areas with concentrations of chromium and lead are higher than the rest of the points of monitoring. Moreover, it is observed that the highest levels of metals found in sediment of finer texture and more organic matter content

Hidrocarbonetos policíclicos aromáticos em sedimentos de fundo do estuário do rio Potengi, região da grande Natal (RN): implicações ambientais

Estuaries are environments prone to the input of chemical pollutants of various kinds and origins, including polycyclic aromatic hydrocarbons (PAHs). Anthropogenic PAHs may have two possible sources: pyrolytic (with four or more aromatic rings and low degree of alkylation) and petrogenic (with two and three aromatic rings and high degree of alkylation). This study aimed to evaluate the levels, distribution and possible sources of polycyclic aromatic hydrocarbons in the estuary of the Potengi river, Natal, Brazil. Samples of bottom sediments were collected in the final 12 km of the estuary until its mouth to the sea, where the urbanization of the Great Natal is more concentrated. Sampling was performed on 12 cross sections, with three stations each, totaling 36 samples, identified as T1 to T36. The non alkylated and alkylated PAHs were analyzed by gas chromatography coupled to mass spectrometry (GC / MS). PAHs were detected in all 36 stations with total concentration on each varying 174-109407 ng g-1. These values are comparable to those of several estuarine regions worldwide with high anthropogenic influence, suggesting the record of diffuse contamination installed in the estuary. PAHs profiles were similar for most stations. In 32 of the 36 stations, low molecular weight PAHs (with 2 and 3 ring: naphthalene, phenanthrene and their alkylated homologues) prevailed, which ranged from 54% to 100% of the total PAH, indicating that leaks, spills and combustion fuels are the dominant source of PAH pollution in the estuary. The level of contamination by PAHs in most stations suggests that there is potential risk of occasional adverse biological effects, but in some stations adverse impacts on the biota may occur frequently. The diagnostic ratios could differentiate sources of PAHs in sediments of the estuary, which were divided into three groups: petrogenic, pyrolytic and mixing of sources. The urban concentration of the Great Natal and the various industrial activities associated with it can be blamed as potential sources of PAHs in bottom sediments of the estuary studied. The data presented highlight the need to control the causes of existing pollution in the estuary

O Prêmio Nacional de Qualidade e as políticas e práticas de recursos humanos :um estudo em empresas do setor de transporte público por ônibus da região metropolitana de Natal/RN

This work has goal of analyzing the practices of Human Resources in the per missionary enterprises of urban transportation, by bus, in the metropolitan region of de Natal, based on the standard person of the National Program of Quality 2004 and points if they are able to take part as prize-winning in this standard. Also this work aims, through a theoretical evolution of people management and its current practices, the history of the National prize Quality and its main standards, the importance of the urban transportation, its characteristics and the system itself in the metropolitan region of Natal. The research was carried out in 11 enterprises that operated in the area, with several dimensions and forms of management. The research variations were based on the standard person of the 2004 NPQ that deals with the system of work, preparation and development and life quality. In the statistical treatment, discriminated and exploiting analyses were applied. The main obtained results through the research, we can verify an administrative centralization in managers and owners hands; that 45% of the enterprises don t have a Human Resources Department, however, on the other hand, they practice some human Resources politics, indicated by the variations; as to the items system of work, 55% of the enterprises are able; preparing and development, 43%

Otimização de escalas de serviço de tripulações estudo de caso em uma empresa de transporte urbano na região metropolitana de Natal/RN

This work aims to "build" rostering urban bus crews to minimize the cost of overtime. For this purpose a mathematical model was developed based on case study in an urban transport company in the metropolitan region of Natal. This problem is usually known in the literature as the Crew Scheduling Problem (CSP) and classified as NP-hard. The mathematical programming takes into account constraints such as: completion of all trips, daily and maximum allowable range of home and / or food. We used the Xpress-MP software to implement and validate the proposed model. For the tested instances the application of the model allowed a reduction in overtime from 38% to 84%

Estudo da formulação de massas cerâmicas provenientes da região do Seridó-RN para fabricação de telhas

This work has for objective study compared the characteristics and technological properties of ceramic bodies from the region of Seridó-RN. The region under study has identified 23 cities where they were 80 ceramics industries. To define the universe of search, there was a survey of pottery that are part of APL Seridó next to the IEL. The characteristics and operating conditions of ceramics industries of the region were identified through a socio-economic questionnaire applied locally, which addressed issues such as: profiles of companies, production process etc. The analysis of information collected from 24 companies identified in seven cities shows that the vast majority of industries is small, with family structure, obsolete equipment and labo, little qualified. Most of the pottery works with low technical knowledge, poor control of the production process and product technology. The raw collected were submitted to analysis of X ray diffraction, chemical composition, termical analysis, particle size distribution and plasticity. Then were produced five formulations and made by uniaxial pressure at 25 MPa for firing in temperatures varying from 850 to 1050 °C. The firing technological properties evaluated were: mass loss to fire, lineal shrinkage, apparent density, apparent porosity, water absorption and flexural strength (3 points). The results indicated that the raw materials from the region have significant similarities in the composition chemical and mineralogical. Furthermore, it indicates the possibility of the use of cycles of firing faster and efficient than the current, limited to some clay mass burning of certain conditions

Avaliação do processo industrial da cerâmica vermelha na região do Seridó - RN

Particularly in Braziland in Rio Grande do Norte, companies manufacturing red ceramic, play an important role as agents of development to study the region Seridó- RN, specific place for carrying out the research. It is observed in this region a concentration of red ceramic industries of small size, which, despite its importance in the ceramic, they are unable to enjoy or use the new forms of administrative management and technological advances designed and offered by universities, centers of research and projects of governments, remained almost entirely outside the progress and modernization, technological and administrative. These companies still have outdated technology, and management processes, providing quality problems and standardization of end products. Upon these conditions are the companies going through crisis and struggling to survive alone and without assistance. The region of Seridó-RN, lets make a detailed case study of red ceramic companies in the region proposed from the existing theoretical and actual lifting of the condition of the product manufacturing red ceramic, allowing through this overview of the implementation of collect samples of raw materials, allowing the study of each ceramic industry that contributed to the participation of the research, which was determined parameters such as: analysis of the physical, chemical and technological properties of raw materials, characterization of the processes used, raising the technological resources considering equipment, machinery, supplies, raw materials and facilities available and its organization by type of products from companies involved in this study. The methodology consists of the following steps: collection of raw material, crushing and screening, characterization of raw materials (liquid limit, chemical analysis, mineralogical analysis, differential thermal analysis, sieve analysis), mixing, forming, cutting, drying and burning of ceramic bodies and bodies of evidence. The results showed that it was clay with distinct characteristics with respect to plasticity. With respect to the different compositions of mixtures of ceramic masses, we conclude that the ceramic properties showed a direct proportionality with increasing fraction of the clay not plastic. However, the compositions of the masses studied proved to be the most appropriate for the types of simulated clay for use in ceramics. Adopted in the ceramic processing made it possible to obtain products the resulted in consistent properties, and in some cases even exceeding the requirements of technical studies and standard-Brazilian clays to obtain ceramic products such as tiles, bricks and tiles to floor. Based on the discussions from the results obtained in the various processing steps of this work, one can draw conclusions according to the physico-chemical and mineralogical properties of raw materials, the properties of ceramic products burned and analysis. This work may be used by other researchers, private companies and governmental organizations, undergraduate students and graduate, can develop studies and future research to: develop projects to modify the furnaces; mapping projects develop and rationalize the exploitation of raw materials ;promoting reforestation and forest management; develop reduction projects and recovery of waste; develop training projects in manpower sector, and develop security projects, improving the conditions of work in the area pottery