X-ray single crystal and powder diffraction: possibilities and applications

In this article the main possibilities of single crystal and powder diffraction analysis using conventional laboratory x-ray sources are introduced. Several examples of applications with different solid samples and in different fields of applications are shown illustrating the multidisciplinary capabilities of both techniques.

The measured variation of the Debye-Waller factor of aluminum from 295K to 815K by using the energy dispersive x-ray diffraction technique

The Energy Dispersive X-ray Diffraction System at Brock University has been used to measure the intensities of the diffraction lines of aluminum powder sample as a function of temperature. At first, intensity measurements at high temperature were not reproducible. After some modifications have been made, we were able to measure the intensities of the diffraction lines to 815K, with good accuracy and reproducibility. Therefore the changes of the Debye-Waller factor from room temperature up to 815K for aluminum were determined with precision. Our results are in good agreement with those previously published.

X-ray diffraction studies of muscle : observations on the anterior byssus retractor muscle of Mytilus edulis and the insect flight muscle from Sarcophaga bullata

The interfilament spacing of the anterior byssus retractor muscle from Mytilus edulis was studied as the muscle was extended. It was found that variations in this spacing were very small and consistent with the hypothesis that the interfilament spacing was independent of the extension of the muscle. It was observed that the interfilament spacing was dependent on the osmolarity of the bathing medium. In concentrated solutions of the artificial seawater, the interfilament spacing decreased; while in dilute solutions of artificial seawater, it was observed that the interfilament spacing was increasing. X-ray diffraction patterns were obtained from fresh, and glutaraldehyde fixed, specimens of insect flight muscle from Sarcophaga bullata. There patterns were in general agreement with previous X-ray diffraction studies of insect flight muscle. A reflexion G at 93A was observed and interpreted as arising from diffraction in the mitochondria. Specimens of dried insect flight muscle produced a diffraction pattern consisting of arc and ring reflexions. This was interpreted as suggesting an ordered arrangement of cristae, in the mitochondria from these muscles.

X-ray diffraction from Al powder using energy dispersive technique

Using the energy dispersive x ...ray diffraction (EDXD) technique, the room temperature diffraction pattern of Al powder was obtained at diffraction angles ~ 30° and 50°. From the small angle diffraction pattern the average relative intensities (IR) of the (111), (200), and (220) lines were measured to be equal to 100, 62, and 32 respectively. From the large diffraction angle IR for the (220), (311+222), (400), (331+420), and (422) lines were measured to be 100,201,17,90, and 19.5 respectively. The diffraction pattern at those two angles were obtained at several higher temperatures to measure the change in the intensities of the Al lines. From the intensity changes the increase of the Debye- Waller temperature factor, i.e ~B(T), with respect to the value at room temperature was determined to be 0.6+0.1 at 250°C, 1.10+0.15 at 350°C, 1.45+0.20 at 450°C, and 2.20±0.35 at 550°C.

High temperature X-ray diffraction study of the U4O9 formation on UO2 sintered plates

The surface oxidation of UO2 sintered plates at 170-275 ° C was studied in situ by high temperature X-ray diffractometry. At very low oxygen concentration, UO2 is oxidized to U4O9, while at 300°C and argon-20 vol% oxygen it is oxidized up to U3O7. X-ray diffraction profiles of the UO2, U4O9 and U3O7 phases were well characterized during the transformations. The activation energy for the transformation of UO2 to U4O9, obtained from X-ray diffraction data, was found to be 117 ± 9 kJ/mol and 90 ± 14 kJ/mol for the β-(311) and α-(200) reflections, respectively. © 1991.

Importance of considering a material micro-failure criterion in the numerical modelling of the shot peening process applied to parabolic leaf springs

Shot peening is a cold-working mechanical process in which a shot stream is propelled against a component surface. Its purpose is to introduce compressive residual stresses on component surfaces for increasing the fatigue resistance. This process is widely applied in springs due to the cyclical loads requirements. This paper presents a numerical modelling of shot peening process using the finite element method. The results are compared with experimental measurements of the residual stresses, obtained by the X-rays diffraction technique, in leaf springs submitted to this process. Furthermore, the results are compared with empirical and numerical correlations developed by other authors.

Desenvolvimento de um papel de filtro de baixo custo para tratamento de água

É sabido que devido à escassez de água potável, nomeadamente em países sub-desenvolvidos, morrem milhares de pessoas por ano, com a procura de fontes de água alternativas, que por sua vez se encontram contaminadas com microrganismos patogénicos; a este facto também se salienta a possibilidade de ocorrência de catástrofes naturais, tornando-se necessário o desenvolvimento de sistemas de desinfecção prácticos, de baixo custo e eficientes. O trabalho experimental desenvolvido focou-se nestas realidades, tendo por objectivo principal o desenvolvimento de um papel bactericida, em particular, um papel de baixo custo como é o caso do papel de filtro de café, para aplicação em desinfecção de água. Este papel foi funcionalizado com nanopartículas sintetizadas de prata, óxido de zinco e com ambas, assim como com nanopartículas comerciais, cuja caracterização foi feita por Microscopia Electrónica de Varrimento (SEM, Scanning Electron Microscopy), Energia Dispersiva de Raios-X (EDS, Energy-dispersive X-ray Spectroscopy), Espectroscopia de Ultravioleta-Visível (UV-VIS Uv-Visible Spectroscopy), Difracção de Raios-X (DRX, X-Rays Diffraction), Análise Termogravimétrica (TA, Thermal Analysis), e Calorimetria Diferencial de Varrimento (DSC, Differencial Scanning Calorimetry) e a actividade anti-bacteriana dos papéis foi avaliada através de Testes de Sensibilidade aos Antibióticos, pelo Método de Kirby-Bauer, contra as bactérias S.a.ATCC25923 e E.coli ATCC25922. No decorrer das sínteses variaram-se alguns parâmetros consoante o tipo de nanopartícula, para as np´s de prata variou-se essencialmente a metodologia de síntese e o tipo de redutor, para as np´s de óxido de zinco, dado ser um composto fotossensível, submeteu-se o papel á luz ultravioleta, o que, por outro lado também esterelizava o papel, e para ter uma comparação, esterelizou-se também o papel pela autoclave, constatando-se, pelas técnicas de caracterização, nomeadamente DRX, que os papeis não continham nanopartículas de óxido de zinco mas sim de acetato de zinco. Surpreendentemente, nos papéis autoclavados já se detectou a presença de óxido de zinco. Com os papéis que evidenciararam maior actividade anti-bacteriana realizaram-se filtrações de membrana com amostras de água contaminada e a determinação da concentração de metal no filtrado foi realizada pela técnica de Espectroscopia de Absorção Atómica de Chama (Flame Atomic Absorption Spectroscopy) conseguindo-se uma taxa de redução bacteriana de practicamente 100% para E.coli NCTC 9001 e E.f NCTC775 com os papéis contendo acetato de zinco numa concentração de 50 mM e np´sAg e acetato de zinco, numa concentração de 10 mM. De forma a validar o trabalho desenvolvido a parte final consistiu em testar os filtros com melhores propriedades em águas contaminadas, tendo esse trabalho sido feito no Laboratório de Água de Consumo dos Serviços Municipalizados de Água e Saneamento de Almada.

Síntesis por reacción en estado sólido del clorapatito de plomo (Piromorfita)

En el presente trabajo se estudia la síntesis de la reacción en el estado sólido entre el Pbs(PO4)a y el PbCla y la influencia de la temperatura sobre dicha reacción. La fase sintetizada, sometiendo la mezcla a diferentes tiempos de calefacción y a diversos intervalos de temperaturas, ha sido estudiada mediante difracción de rayos X.

Structural and optical properties of dilute InAsN grown by molecular beam epitaxy

We perform a structural and optical characterization of InAs1¿xNx epilayers grown by molecular beam epitaxy on InAs substrates x 2.2% . High-resolution x-ray diffraction HRXRD is used to obtain information about the crystal quality and the strain state of the samples and to determine the N content of the films. The composition of two of the samples investigated is also obtained with time-of-flight secondary ion mass spectroscopy ToF-SIMS measurements. The combined analysis of the HRXRD and ToF-SIMS data suggests that the lattice parameter of InAsN might significantly deviate from Vegard"s law. Raman scattering and far-infrared reflectivity measurements have been carried out to investigate the incorporation of N into the InAsN alloy. N-related local vibrational modes are detected in the samples with higher N content. The origin of the observed features is discussed. We study the compositional dependence of the room-temperature band gap energy of the InAsN alloy. For this purpose, photoluminescence and optical absorption measurements are presented. The results are analyzed in terms of the band-anticrossing BAC model. We find that the room-temperature coupling parameter for InAsN within the BAC model is CNM=2.0 0.1 eV.

Epitaxial growth of biferroic YMnO3(0001) on platinum electrodes

Epitaxial films of the biferroic YMnO3 (YMO) oxide have been grown on platinum-coated SrTiO3(1 1 1) and Al2O3(0 0 0 1) substrates. The platinum electrodes, (1 1 1) oriented, are templates for the epitaxy of the hexagonal phase of YMO with a (0 0 0 1) out-of-plane orientation, which is of interest as this is the polarization direction of YMO. X-ray diffractometry indicates the presence of two crystal domains, 60° rotated in-plane, in the Pt(1 1 1) layers which subsequently are transferred on the upperlaying YMO. Cross-section analysis by high-resolution transmission electron microscopy (HRTEM) of YMnO3/Pt/SrTiO3(1 1 1) shows high-quality epitaxy and sharp interfaces across the structure in the observed region. We present a detailed study of the epitaxial growth of the hexagonal YMO on the electrodes.

Kerr measurements on single-domain SrRuO3 thin films

We report on the magneto-optical measurements of an epitaxial SrRuO3 film grown on SrTiO3 (0 0 1), which previously was determined to be single domain orientated by x-ray diffraction and Raman spectroscopy techniques. Our experiments reveal a large Kerr rotation, which reaches a maximum value of about 0.5° at low temperature. By measuring magnetic hysteresis loops at different temperatures, we determined the temperature dependence of the Kerr rotation in the polar configuration. Values of the anisotropic magnetoresistance ~ 20% have been measured. These values are remarkably higher than those of other metallic oxides such as manganites. This striking difference can be attributed to the strong spin-orbit interaction of the Ru 4d ion in the SrRuO3 compound.

Effect of pressure on La2(WO4)3 with a modulated scheelite-type structure

We have studied the effect of pressure on the structural and vibrational properties of lanthanum tritungstate La2(WO4)3. This compound crystallizes under ambient conditions in the modulated scheelite-type structure known as the α phase. We have performed x-ray diffraction and Raman scattering measurements up to a pressure of 20 GPa, as well as ab initio calculations within the framework of the density functional theory. Up to 5 GPa, the three methods provide a similar picture of the evolution under pressure of α-La2(WO4)3. At 5 GPa, we begin to observe some structural changes, and above 6 GPa we find that the x-ray patterns cannot be indexed as a single phase. However, we find that a mixture of two phases with C2/c symmetry accounts for all diffraction peaks. Our ab initio study confirms the existence of several C2/c structures, which are very close in energy in this compression range. According to our measurements, a state with medium-range order appears at pressures above 9 and 11 GPa, from x-ray diffraction and Raman experiments, respectively. Based upon our theoretical calculations we propose several high-pressure candidates with high cationic coordinations at these pressures. The compound evolves into a partially amorphous phase at pressures above 20 GPa.

Domain matched epitaxial growth of Bi1.5Zn1Nb1.5O7 thin films by pulsed laser deposition

Bi1.5Zn1Nb1.5O7 (BZN) epitaxial thin films were grown by pulsed laser deposition on Al2O3 with a double ZnO buffer layer through domain matching epitaxy (DME) mechanism. The pole figure analysis and reciprocal space mapping revealed the single crystalline nature of the thin film. The pole figure analysis also shows a 60º twinning for the (222) oriented crystals. Sharp intense spots in the SAED pattern also indicate the high crystalline nature of BZN thin film. The Fourier filtered HRTEM images of the BZN-ZnO interface confirms the domain matched epitaxy of BZN with ZnO buffer. An electric field dependent dielectric tunability of 68% was obtained for the BZN thin films with inter digital capacitors patterned over the film.

Caracterizacion por difraccion de rayos-X, analisis termico y espectroscopia Raman de los cristales mixtos Li(NH4)(1-x)KxSO4

En este trabajo se estudia la preparació n y caracterizació n de las fases de los cristales mixtos de f órmula Li(NH4)1-xKxSO4. La caracterizacói n se ha efectuado por aná lisis té rmico con DSC y ATD, difracci ón de rayos-X sobre polvo cristalino con temperatura variable, difracci n de rayos-X sobre muestra monocristalina a temperatura variable a fin de determina su estructura cristalina y por espectroscop"a Raman a temperatura variable. Se han obtenido dos tipos de fases. Una soluci n s lida con 0.94 < x < 1 que presenta los mismos tipos estructurales que el LiKSO4, pero seg n el m todo de cristalizaci n pueden aparecer nuevas fases que no presenta el LiKSO4. El segundo tipo de compuesto tiene por f rmula Li(NH4)0.53K0.47SO4, el cual presenta una estructura hexagonal con par metro a » 3 aLiKSO4. Este compuesto tiene por encima de la temperatura ambiente una sola transici n a 463K.

Estudio del sistema Li2SO4-Na2SO4. Diagrama de fases y caracterizacion del LiNaSO4

Se presenta un estudio exhaustivo del diagrama de fase del sistema binario Li2SO4-Na2SO4. El diagrama de fases se determinó mediante termo-difractometría de rayos-X en muestras de polvo y calorimetría ATD. Se obtiene una nueva fase de fórmula Li2-xNaxSO4, con 1 ¿ x ¿ 1.22. La estructura cristalina de ß-LiNaSO4 se determinó por difracción de rayos-X sobre un monocristal. Este estudio muestra que los cristales usualmente se maclan cuando el crecimiento es por solución, lo cual explica la baja polarización espontánea. Se explica la dispersión Raman de los compuestos Li2SO4, Na2SO4 y LiNaSO4, a partir de los datos estructurales. Las medidas experimentales se han efectuado a diferentes velocidades de calentamiento y enfriamiento.