Rapid prototyping of polymeric electrophoresis microchips with integrated copper electrodes for contactless conductivity detection

A simple and easy approach to produce polymeric microchips with integrated copper electrodes for capacitively coupled contactless conductivity detection (CD) is described. Copper electrodes were fabricated using a printed circuit board (PCB) as an inexpensive thin-layer of metal. The electrode layout was first drawn and laser printed on a wax paper sheet. The toner layer deposited on the paper sheet was thermally transferred to the PCB surface working as a mask for wet chemical etching of the copper layer. After the etching step, the toner was removed with an acetonitrile-dampened cotton. A poly(ethylene terephthalate) (PET) film coated with a thin thermo-sensitive adhesive layer was used to laminate the PCB plate providing an insulator layer of the electrodes to perform CID measurements. Electrophoresis microchannels were fabricated in poly(dimethylsiloxane) (PDMS) by soft lithography and reversibly sealed against the PET film. These hybrid PDMS/PET chips exhibited a stable electroosmotic mobility of 4.25 +/- 0.04 x 10(-4) V cm(-2) s(-1), at pH 6.1, over fifty runs. Efficiencies ranging from 1127 to 1690 theoretical plates were obtained for inorganic cations.

Development of new rapid prototyping process

Purpose - The purpose of this paper is to identify the key elements of a new rapid prototyping process, which involves layer-by-layer deposition of liquid-state material and at the same time using an ultraviolet line source to cure the deposited material. This paper reports studies about the behaviour of filaments, deposition accuracy, filaments interaction and functional feasibility of system. Additionally, the author describes the process which has been proposed, the equipment that has been used for these studies and the material which was developed in this application. Design/methodology/approach - The research has been separated into three study areas in accordance with their goals. In the first, both the behaviour of filament and deposition accuracy was studied. The design of the experiment is described with focus on four response factors (bead width, filament quality, deposition accuracy and deposition continuity) along with function of three control factors (deposition height, deposition velocity and extrusion velocity). The author also studied the interaction between filaments as a function of bead centre distance. In addition, two test samples were prepared to serve as a proof of the methodology and to verify the functional feasibility of the process which has been studied. Findings - The results show that the proposed process is functionally feasible, and that it is possible to identify the main effects of control factors over response factors. That analysis is used to predict the condition of process as a function of the parameters which control the process. Also identified were distances of centre beads which result in a specific behaviour. The types of interaction between filaments were analysed and sorted into: union, separation and indeterminate. At the end, the functional feasibility of process was proved whereby two test parts could be built. Originality/value - This paper proposes a new rapid prototyping process and also presents test studies related to this proposition. The author has focused on the filament behaviour, deposition accuracy, interaction between filaments and studied the functional feasibility of process to provide new information about this process, which at the same time is useful to the development of other rapid prototyping processes.

Architectural prototyping: from CCS to .Net

Over the last decade, software architecture emerged as a critical issue in Software Engineering. This encompassed a shift from traditional programming towards software development based on the deployment and assembly of independent components. The specification of both the overall systems structure and the interaction patterns between their components became a major concern for the working developer. Although a number of formalisms to express behaviour and to supply the indispensable calculational power to reason about designs, are available, the task of deriving architectural designs on top of popular component platforms has remained largely informal. This paper introduces a systematic approach to derive, from CCS behavioural specifications the corresponding architectural skeletons in the Microsoft .Net framework, in the form of executable C and Cω code. The prototyping process is fully supported by a specific tool developed in Haskell

Prototyping Concurrent Systems in Cw

Software architecture is currently recognized as one of the most critical design steps in Software Engineering. The specification of the overall system structure, on the one hand, and of the interactions patterns between its components, on the other, became a major concern for the working developer. Although a number of formalisms to express behaviour and supply the indispensable calculational power to reason about designs, are available, the task of deriving architectural designs on top of popular component platforms has remained largely informal. This paper introduces a systematic approach to derive, from behavioural specifications written in Cw, the corresponding architectural skeletons in the Microsoft .NET framework in the form of executable code

Prototyping Behavioural Specifications in the.NET framework

Over the last decade, software architecture emerged as a critical design step in Software Engineering. This encompassed a shift from traditional programming towards the deployment and assembly of independent components. The specification of the overall system structure, on the one hand, and of the interactions patterns between its components, on the other, became a major concern for the working developer. Although a number of formalisms to express behaviour and supply the indispensable calculational power to reason about designs, are available, the task of deriving architectural designs on top of popular component platforms has remained largely informal. This paper introduces a systematic approach to derive, from behavioural specifications written in Ccs, the corresponding architectural skeletons in the Microsoft .Net framework in the form of executable C] code. Such prototyping process is automated by means of a specific tool developed in Haskell

An object-oriented model for rapid prototyping of data path/control systems - a case study

Publicado em "Information control in manufacturing 1998 : (INCOM'98) : advances in industrial engineering : a proceedings volume from the 9th IFAC Symposium, Nancy-Metz, France, 24-26 June 1998. Vol. 2"

Rapid prototyping of compliant human aortic roots for assessment of valved stents.

Adequate in-vitro training in valved stents deployment as well as testing of the latter devices requires compliant real-size models of the human aortic root. The casting methods utilized up to now are multi-step, time consuming and complicated. We pursued a goal of building a flexible 3D model in a single-step procedure. We created a precise 3D CAD model of a human aortic root using previously published anatomical and geometrical data and printed it using a novel rapid prototyping system developed by the Fab@Home project. As a material for 3D fabrication we used common house-hold silicone and afterwards dip-coated several models with dispersion silicone one or two times. To assess the production precision we compared the size of the final product with the CAD model. Compliance of the models was measured and compared with native porcine aortic root. Total fabrication time was 3 h and 20 min. Dip-coating one or two times with dispersion silicone if applied took one or two extra days, respectively. The error in dimensions of non-coated aortic root model compared to the CAD design was <3.0% along X, Y-axes and 4.1% along Z-axis. Compliance of a non-coated model as judged by the changes of radius values in the radial direction by 16.39% is significantly different (P<0.001) from native aortic tissue--23.54% at the pressure of 80-100 mmHg. Rapid prototyping of compliant, life-size anatomical models with the Fab@Home 3D printer is feasible--it is very quick compared to previous casting methods.

Ramp-up Predictability - Designing and Prototyping Ramp-up Predictability concept for new product creation

Diplomityön tavoitteena on tutkia ja kehittää menetelmä tuotekehitysprojektin ajalliselle ennustamiselle tuotteen siirtyessä tuotekehityksestä massatuotantoon. Ajallisen ennustamisen merkitys korostuu mitä lähemmäksi uuden tuotteen massatuotannon aloittaminen (ramp-up) tulee, koska strategiset päätökset koskien mm. uusia tuotantolinjoja, materiaalien- ja komponenttien tilaamisia sekä vahvistus asiakastoimitusten aloittamista täytyy tehdä jo paljon aikaisemmin.Työ aloitetaan tutkimalla rinnakkaista insinöörityötä (concurrent engineering) sekä suoritusten mittaamista (performance measurement), joiden sisältämistä ajattelumalleista, työkaluista ja tekniikoista hahmottuivat ajallisen ennustettavuuden onnistumisen edellytykset. Näitä olivat suunnitellun tuotteen ja tuotekehitysprosessin laatu sekä resurssien ja tiimien kompetenssit. Toisaalta ajalliseen ennustettavuuteen vaikuttavat myös projektien riippuvuudet ulkoisista toimittajista ja heidän aikatauluistaan.Teoreettisena viitekehyksenä käytetään Bradford L. Goldense:n luomaa mallia tuotekehityksen proaktiiviseksi mittaamiseksi sekä sovelletaan W. Edward Deming:in jatkuvan parantamisen silmukkaa. Työssä kehitetään Ramp-up Predictability konsepti, joka koostuu keskipitkän ja pitkän aikavälin ennustamisesta. Työhön ei kuulunut mallin käyttöönotto ja seuranta.Toimenpide ehdotuksena esitetään lisätutkimusta mittareiden keskinäisestä korrelaatioista ja niiden luotettavuudesta sekä mallien tarjoamista mahdollisuuksista muille tulosyksiköille.

Towards open access networks – prototyping with the Lappeenranta model

The provision of Internet access to large numbers has traditionally been under the control of operators, who have built closed access networks for connecting customers. As the access network (i.e. the last mile to the customer) is generally the most expensive part of the network because of the vast amount of cable required, many operators have been reluctant to build access networks in rural areas. There are problems also in urban areas, as incumbent operators may use various tactics to make it difficult for competitors to enter the market. Open access networking, where the goal is to connect multiple operators and other types of service providers to a shared network, changes the way in which networks are used. This change in network structure dismantles vertical integration in service provision and enables true competition as no service provider can prevent others fromcompeting in the open access network. This thesis describes the development from traditional closed access networks towards open access networking and analyses different types of open access solution. The thesis introduces a new open access network approach (The Lappeenranta Model) in greater detail. The Lappeenranta Model is compared to other types of open access networks. The thesis shows that end users and service providers see local open access and services as beneficial. In addition, the thesis discusses open access networking in a multidisciplinary fashion, focusing on the real-world challenges of open access networks.

Rapid prototyping: pikavalmistuksen mahdollisuudet tuotekehityksessä

Tämän kandidaatintyön tavoitteena on selvittää miten pikavalmistusta voidaan hyödyntää tuotekehityksessä ja mitä mahdollisuuksia se tarjoaa tuotekehityksen kehittämiseksi ja monipuolistamiseksi. Työn teoreettisessa osuudessa selvennetään pikavalmistuksen teknistä toimintaa ja sen liittymistä tuotekehitysprosessiin. Tuotekehitysteorioista esitellään yleisimmät teoriat ja niiden menetystekijät sekä ongelmat. Työn jälkimmäisessä osassa esitellään pikavalmistuksen mahdollisuudet ja hyödyt tuotekehityksissä. Pikavalmistuksen hyödyntämisen edellytykset esitellään viimeiseksi. Tutkielma on toteutettu kirjallisuustyönä ja saadut tulokset perustuvat alan kirjallisuuteen ja artikkeleihin. Tutkimuksessa selvisi, että pikavalmistuksen avulla pystytään pienentämään tuotekehityksen kustannuksia merkittävästi. Tuotekehitykseen kuluvaa aikaa voidaan lyhentää huomattavasti. Suunnittelun laatua pystytään parantamaan ja poistamaan suunnittelun rajoituksia. Valmistusteknisesti pikavalmistuksella on joitakin ylivertaisia ominaisuuksia perinteisiin valmistustekniikoihin nähden.

Small teleoperated vehicles: study of potential use cases and empirical prototyping

This thesis researches the current state of small teleoperated devices, the need for them and developing one. Small teleoperated devices give the possibility to perform tasks that are impossible or dangerous for humans. This work concentrates on small devices and cheap components and discloses one way of developing a teleoperated vehicle, but not necessarily the optimal way. Development and the current state of teleoperation were studied by a literature review, in which the data was searched from literature as well as from the Internet. The need for teleoperated devices was mapped through a survey, where 11 professionals from variating fields were interviewed how they could utilize a teleoperated devices and with what kind of features. Also, a prototype was built as a proof of concept of small teleoperated devices. The prototype is controlled by a single-board microcomputer that also streams video to the controlling device. The video can be viewed on a display or with a head mounted display.

Applying 3D modelling technology to traditional craftwork : rapid prototyping in artisanal jewellery making and its impact on the perceived value of jewellery

Depuis la révolution industrielle, l’évolution de la technologie bouleverse le monde de la fabrication. Aujourd'hui, de nouvelles technologies telles que le prototypage rapide font une percée dans des domaines comme celui de la fabrication de bijoux, appartenant jadis à l'artisanat et en bouscule les traditions par l'introduction de méthodes plus rapides et plus faciles. Cette recherche vise à répondre aux deux questions suivantes : - ‘En quoi le prototypage rapide influence-t-il la pratique de fabrication de bijoux?’ - ‘En quoi influence-t-il de potentiels acheteurs dans leur appréciation du bijou?’ L' approche consiste en une collecte de données faite au cours de trois entretiens avec différents bijoutiers et une rencontre de deux groupes de discussion composés de consommateurs potentiels. Les résultats ont révélé l’utilité du prototypage rapide pour surmonter un certain nombre d'obstacles inhérents au fait-main, tel que dans sa géométrie, sa commercialisation, et sa finesse de détails. Cependant, il se crée une distance entre la main du bijoutier et l'objet, changeant ainsi la nature de la pratique. Cette technologie est perçue comme un moyen moins authentique car la machine rappelle la production de masse et la possibilité de reproduction en série détruit la notion d’unicité du bijou, en réduisant ainsi sa charge émotionnelle. Cette recherche propose une meilleure compréhension de l'utilisation du prototypage rapide et de ses conséquences dans la fabrication de bijoux. Peut-être ouvrira-t-elle la voie à une recherche visant un meilleur mariage entre cette technique et les méthodes traditionnelles.

FEM based Virtual Prototyping and Design of Third Harmonic Excitation System for Low Voltage Brushless Alternators

Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.