基于MSP430 单片机和DS18B20 的多分支多通道温度测量系统远程监控软件

This paper present that the system can acquire the remote temperature measurement data of 40 monitoring points,through the RS-232 serial port and the Intranet.System s hardware is consist of TI s MSP430F149 mixed-signal processor and UA7000A network module.Using digital temperature sensor DS18B20,the structure is simple and easy to expand,the sensors directly send out the temperature data.MSP430F149 has the advantage of ultra-low-power and high degree of integration.Using msp430F149,the multi-branch multi-p...中文文摘：文章论述了通过RS-232串口和Intranet网络,来实现对远端的40个温度测量点的监控。系统硬件由TI公司的MSP430F149混合信号处理器和UA7000A网络模块构成。传感器采用数字式温度传感器DS18B20,它将直接得到温度的数字量,结构简单,易于扩展。MSP430F149处理器具有超低功耗和高度集成等优点,利用它构建的多分支多通道温度测量系统功能强大,结构简单,可靠性高,抗干扰能力强。系统客户端软件采用Microsoft Visual C++6.0设计。本监控系统能够很好地完成对4个分支共40个温度测量点的远程实时监控。

基于TCP/ IP 协议的CSR离子泵电源远程监控软件系统设计

This paper discuss a Ion-pump Power Supply control system making use of RS232 series bus and Intranet.The system s hardware VAC800 is composed of MSP430F149 mixed-signal processors produced by TI and UA7000A network model.MSP430F149 has advantages of ultra-low-power and high-integration.The Ion-pump Power Supply control system has the characteristics of strong function,simple structure,high reliability,strong resistance of noise,no peripheral chip,etc.Visual studio 2005 is used to design the system s softwa...中文文摘：论述了通过RS-232总线和Intranet网络,来实现对远端的离子泵电源的监测与控制。系统硬件VAC800由TI公司的MSP430F149混合信号处理器和UA7000A网络模块构成。MSP430F149具有超低功耗和高集成度等优点,利用它构建的离子泵电源监控系统功能强大,结构简单,可靠性高,抗干扰能力强。系统软件采用visual studio 2005设计。本监控系统能够很好地完成对加速器离子泵电源监视与控制。

基于TCP/IP协议的CSR离子泵电源远程监控软件系统设计

论述了通过RS-232总线和Intranet网络,来实现对远端的离子泵电源的监测与控制。系统硬件VAC800由TI公司的MSP430F149混合信号处理器和UA7000A网络模块构成。MSP430F149具有超低功耗和高集成度等优点,利用它构建的离子泵电源监控系统功能强大,结构简单,可靠性高,抗干扰能力强。系统软件采用visual studio 2005设计。本监控系统能够很好地完成对加速器离子泵电源监视与控制。

基于MSP430单片机和DS18B20的多分支多通道温度测量系统远程监控软件设计

文章论述了通过RS-232串口和Intranet网络,来实现对远端的40个温度测量点的监控。系统硬件由TI公司的MSP430F149混合信号处理器和UA7000A网络模块构成。传感器采用数字式温度传感器DS18B20,它将直接得到温度的数字量,结构简单,易于扩展。MSP430F149处理器具有超低功耗和高度集成等优点,利用它构建的多分支多通道温度测量系统功能强大,结构简单,可靠性高,抗干扰能力强。系统客户端软件采用Microsoft Visual C++6.0设计。本监控系统能够很好地完成对4个分支共40个温度测量点的远程实时监控。

用于加速器控制的通用型TCP/IP-多串口协议转换器的研制

在加速器控制领域,经常涉及到要将带有标准RS-232串行接口的设备通过以太网连接来实现远程测控任务,本文所介绍的设计工作解决了8个串口设备通过一台基于CPLD和MSP430技术的通用型TCP/IP-多串口协议转换器来完成远程数据/命令的传送。

基于ARM920T的HIRFL-CSR前端总线控制器FBC-01

本文论述用于兰州重离子加速器冷却存储环(HIRFL-CSR)控制系统的前端总线系统控制器FBC-01的硬件设计。该控制器是基于0.8mmBGA封装的AT91RM9200(ARM9)处理器,运行嵌入式LINUX操作系统。控制器可以连接标准的VGA显示器、键盘、鼠标,具有通用的10M/100M以太网接口、USB接口、RS-232接口、485接口、CANBUS接口。可以带SD卡、CF卡存储器。该控制器采用现场可编程的FPGA器件设计背板接口,并采用具有64mA高驱动能力的总线驱动器,不仅符合VME规范的电气要求,而且具有灵活的接口信号定义可编程能力,是HIRFL-CSR控制系统的关键部件。

重离子加速器注入器电源控制器的设计；Design of digital power control system applied in sector focusing cyclotron

设计了一种应用于兰州重离子加速器注入器的电源控制器,该控制器基于微处理器AT-mega128,结合MAX7000系列的复杂可编程器件和RTL8019AS网关芯片来实现对电源系统的控制,并通过RS-232总线实现与上位机的串口通信。应用结果表明,该控制器具有良好的通用性、灵活性、可远程控制及性能稳定等特点,实现了注入器磁铁电源10-4量级的幅度稳定性,使注入器引出的束流强度、束流品质、束流稳定性和供束效率等得到很大的提高。

集散式束流诊断器件定位系统

在很多束流诊断系统中，步进电机已被广泛的用于束流诊断器件定位的动力驱动。为了实现对步进电机的本地控制、远地控制和集中控制，我们开发了基于86BYG45OB-O2型步进电机的集散式束流诊断器件定位系统。本文全面论述了一个基于半双工RS-485总线集散式控制系统的设计；根据束流诊断器件定位控制系统需求出发，阐明了控制系统的开发背景、基本结构的建立、硬件设计方案和软件的实现。本论文主要包括五部分：第一部分介绍了在兰州放射性核次级束流装置（RIBL）中，束流诊断器件定位的特点和要求。第二部分分析了原有束流诊断定位系统的结构和不足，说明了集散式束流诊断器件定位系统的结构和优点。第三：部分介绍了Rs-232、RS-422和RS-455及RS-485组网中的有关问题。第四部分详细论述了本地控制单元的硬件和软件的设计。第五部分介绍了远地控制单元的软件设计。

色散型光谱仪的通用计算机系统

通过微机技术与仪器改造技术相结合,探索了色散型光谱仪更新的新途径。以IBM微机为主系统,微机扫描控制器(MSC)为从系统,由RS-232串行通信口连接,以对话方式通讯、协议、交换信息。MSC的使用使系统具备了通用性和灵活性,在色散性光谱仪功能开发上具有广泛应用前景。该系统适用于红外、紫外、可见等色散型光谱仪。原机的测光系统与机械系统基本不变,由于增加了光谱数据处理能力,提高了光谱仪的使用性能。

海洋要素垂直剖面测量系统的数据存储

长期、定点、连续测量海洋环境参数，尤其是从海洋表面到海底的垂直剖面的监测一直以来大都是由船只完成，耗费大量的人力和财力。“海浪驱动自持式海洋要素垂直剖面测量系统”（简称“海马”）利用海洋无时不在的波浪能，驱动滑行器单方向下潜运动，直达海底或程序设定的预定深度，在控制系统作用下，滑行器依靠自身的浮力匀速上浮， 并在此过程中，完成海洋要素的自动测量和存储。 当今海洋仪器大多采用“闪存”来存储数据，主要有RS－232串口和并型口的CF(Compact Flash)卡两种形式。但是两种接口都有一定的缺陷：CF卡不能和PC机直接通信，必须通过转接口才能将数据传送到PC机上；而RS-232接口虽然可以和PC机直接通信，但是由于其传输速度较慢，不利于大量数据的传输。由于上述两种接口的缺点，“海马”采用U盘来实现数据的存储。 USB接口不仅可以和PC机直接通信，而且具有使用方便，数据传输率高，又支持即插即用等特点，但由于USB接口协议复杂，涉及的方面广，特别是软件种类比较多，而且USB芯片种类繁多，使得USB设备的开发非常困难。 本文设计的USB(Universal Serial Bus)接口电路以单片机AT89C51以及CYPRESS公司生产的USB接口芯片SL811HS为核心，结合了随机存储芯片HY62256以及看门狗芯片X25165。在介绍了SL811HS控制器芯片的主要特点的基础上，重点阐述了利用这一芯片在C语言的编程控制之下如何识别U盘的插入和拔出，以及如何将单片机的数据按协议规定写入U盘，其中的协议包括FAT文件协议，USB协议和UFI命令协议。 本系统实现了单片机对U盘的数据存储，速度快，存储容量大，数据读取方便，直观明了，系统工作安全可靠，抗干扰能力强，可扩展性大，而且针对下位机设计的串口协议简单，可以满足“海马”海量数据的存储要求。

Equipamento de biotelemetria para monitoramento em tempo real do teste da caminhada de seis minutos

Este estudo visa desenvolver um sistema portátil de radiocomunicação de radiação restrita, indicado para biotelemetria digital de curta distância aplicada ao Teste da Caminhada de Seis Minutos (TC6M) em pacientes com doença pulmonar obstrutiva crônica ou hipertensão pulmonar. A saturação periférica da hemoglobina (SpO2) e a freqüência cardíaca (FC) são monitoradas em tempo real. É utilizada a banda destinada a aplicações médicas, industriais e científicas (ISM), com freqüência de portadora em 916MHz e potência de transmissão de 0,75mW. Este sistema foi projetado para operar através de um enlace half duplex e codificação Manchester NRZ incorporando um protocolo para correção de erros do tipo automatic repeat request error com utilização de um código CRC-16 para detecção de erros. A velocidade máxima de transmissão de dados é de 115.2 kbps. O sistema é constituído de três partes: unidade portátil (Master), unidade estacionária (Slave) e software de visualização em tempo real. A unidade portátil recebe do oxímetro os parâmetros de monitorização que são transmitidos via enlace de rádio-freqüência. A interface da unidade estacionária com o software é feita através da porta de comunicação serial padrão RS-232. Os testes de laboratório e de campo demonstraram que o sistema de biotelemetria é adequado a realizar o TC6M com precisão de SpO2 de ±3 dígitos (com ±1 desvio padrão) e FC de ±3% ambos com taxa de Frame Error Rate < 10-4 (0,01%), sem restrigir os movimentos do usuário durante o processo de monitorização.

Controle vetorial de velocidade de uma máquina de indução sem mancais trifásica com bobinado dividido utilizando estimação neural de fluxo

This work describes the study and the implementation of the vector speed control for a three-phase Bearingless induction machine with divided winding of 4 poles and 1,1 kW using the neural rotor flux estimation. The vector speed control operates together with the radial positioning controllers and with the winding currents controllers of the stator phases. For the radial positioning, the forces controlled by the internal machine magnetic fields are used. For the radial forces optimization , a special rotor winding with independent circuits which allows a low rotational torque influence was used. The neural flux estimation applied to the vector speed controls has the objective of compensating the parameter dependences of the conventional estimators in relation to the parameter machine s variations due to the temperature increases or due to the rotor magnetic saturation. The implemented control system allows a direct comparison between the respective responses of the speed and radial positioning controllers to the machine oriented by the neural rotor flux estimator in relation to the conventional flux estimator. All the system control is executed by a program developed in the ANSI C language. The DSP resources used by the system are: the Analog/Digital channels converters, the PWM outputs and the parallel and RS-232 serial interfaces, which are responsible, respectively, by the DSP programming and the data capture through the supervisory system

Controle vetorial de velocidade de um motor de indução trifásico com estimação neural de fluxo

This work describes the study and the implementation of the speed control for a three-phase induction motor of 1,1 kW and 4 poles using the neural rotor flux estimation. The vector speed control operates together with the winding currents controller of the stator phasis. The neural flux estimation applied to the vector speed controls has the objective of compensating the parameter dependences of the conventional estimators in relation to the parameter machine s variations due to the temperature increases or due to the rotor magnetic saturation. The implemented control system allows a direct comparison between the respective responses of the speed controls to the machine oriented by the neural rotor flux estimator in relation to the conventional flux estimator. All the system control is executed by a program developed in the ANSI C language. The main DSP recources used by the system are, respectively, the Analog/Digital channels converters, the PWM outputs and the parallel and RS-232 serial interfaces, which are responsible, respectively, by the DSP programming and the data capture through the supervisory system

Proposta de um sistema de segurança eletrônica predial

This work presents a suggestion of a security system of land automation having as objective main the creation of a system capable from easy method, supervise the installations of a building with the goal to preserver security personal and patrimonial necessities, aim at portability low cost and use easiness. Was designed an alarms central and access controller that has digital and analogical inputs for sensors and outputs for buzzer, telephonic dialing and electronic lock. The system is supervised by software that makes solicitations of information to the alarms central through the one computer's serial port (RS-232). The supervisory software was developed in platform LabVIEW with displays the received data on a graphical interface informing the sensors' current states distributed in the building and system events as alarns occurrences. This system also can be viewed through the Internet for people registered by the land security's system administrator