Mechanics of longitudinal rolling of tube through three-grooved rolls

This investigation examined the process of the longitudinal rolling of tubes through a set of three driven grooved rolls. Tubes were rolled with or without internal support i.e. under mandrel rolling or sinking conditions. Knowledge was required of the way in which the roll separating force and rolling torque vary for different conditions of rolling. The objective of this work being to obtain a better understanding and optimization of the mechanics of the process. The design and instrumentation of a complete experimental three-roll mill for the rolling of lead tube as an analogue material for hot steel, with the measurement of the individual roll force and torque is described. A novel type of roll load cell was incorporated and its design and testing discussed. Employing three roll sizes of 170 mm, 255 mm and 340 mm shroud diameter, precise tube specimens of various tube diameter to thickness ratios were rolled under sinking and mandrel rolling conditions. To obtain an indication of the tube-roll contact areas some of the specimens were partially rolled. For comparative purposes the remaining tubes were completely rolled as a single pass. The roll forces, torques and tube parameters e.g. reduction of area, D/t ratio, were collated and compared for each of the three roll diameters considered. The influence of friction, particularly in the mandrel rolling process, was commented upon. Theoretical studies utilising the equilibrium and energy methods were applied to both the sinking and mandrel rolling processes. In general, the energy approach gave better comparison with experiment, especially for mandrel rolling. The influence of the tube deformation zones on the two processes was observed and on the subsequent modification of the tube-roll arc contact length. A rudimentary attempt was made in the theoretical sinking analysis to allow for the deformation zone prior to roll contact; some success was noted. A general survey of the available tube rolling literature, for both the sinking and mandrel processes has been carried out.

Adaptation for tandem cold mill models

The ideal conditions for the operation of tandem cold mills are connected to a set of references generated by models and used by dynamic regulators. Aiming at the optimization of the friction and yield stress coefficients an adaptation algorithm is proposed in this paper. Experimental results obtained from an industrial cold rolling mill are presented. (C) 2008 Elsevier B.V. All rights reserved.

Seostamattoman hitsausteräksen leimuhitsaus

Valssilangan valmistuksessa päättymättömällä valssausprosessilla voidaan parantaa tuotannon tuottavuutta ja joustavuutta. Menetelmän ansiosta myös valssilankakieppien kokoa voidaan vaihdella asiakkaan tarpeiden mukaan. Prosessin joustavuus ja tuottavuus perustuvat liikkuvaan leimuhitsauslaitteistoon, jolla austeniittialueelle kuumennetut teelmät hitsataan toisiinsa ennen valssausta. Koska leimuhitsausliitoksen hyvä laatu on valmistusprosessin kannalta erityisen tärkeää, tutkittiin tässä työssä hitsausparametrien vaikutusta liitoksen laatuun. Hitsausparametreista tärkeimpiä ovat leimutusaika ja -jännite sekä tyssäyksen voima ja määrä. Parametrien ollessa liian suuria muodostuvat liitospinnat liian plastisiksi ja sopivan tyssäysvoiman ylläpitäminen on vaikeaa. Liian pienillä parametreilla liitospintojen plastisoituminen jää kesken ja tyssäys jää puutteelliseksi. Leimuhitsauksen laatuun vaikuttaa myös liitospinta-alan koko. Kaikki nämä tekijät heikentävät liitoksia, joten parametrien optimaalisuus on liitoksen hyvän laadun kannalta välttämätön. Parametrikokeina hitsattujen koekappaleiden rakennetta ja ominaisuuksiatutkittiin ainetta rikkovilla kokeilla. Lyhyemmillä leimutusajoilla hitsatuistakoekappaleista löytyi virheitä, jotka heikensivät huomattavasti liitoksien laatua. Menetelmäkokeiden perusteella koekappaleet eivät kaikilta osin täyttäneet liitosten laatuvaatimuksia.

Ristinivel nelivalssaimen voimansiirrossa

Nelivalssaimia käytetään yleisesti metallinauhojen ja -levyjen kylmämuovaukseen. Valssaimissa ristinivel siirtää vääntömomenttia kahden kulmassa olevan akselin välillä. Tässä tutkimuksessa haettiin ratkaisuja nelivalssaimessa esiintyvään epäsymmetriseen taivutustarpeeseen. Valssattavat kuparinauhat alkavat aaltoilla valssaajan puolelta noin yhden millimetrin paksuudessa. Tutkimuksen tarkastelu rajattiin koskemaan vain voimansiirrossa olevaa ristiniveltä, jonka epäiltiin olevan yksi mahdollinen ongelman aiheuttaja. Tutkimuksessa selvisi, että ristinivel ei aiheuta pystysuuntaisia voimia, jotka vaikuttaisivat suoraan nauhan poikkipintaprofiiliin. Kuitenkin ristinivelen aiheuttamat vaakasuuntaiset voimat voivat vaikuttaa epäsuorasti nauhan poikkipintaprofiiliin. Laatupoikkeamien taloudellinen merkitys havaittiin pieneksi, mutta myöhemmissä prosessivaiheissa kuparinauhan epäsymmetrinen poikkipintaprofiili aiheutti ongelmia.

Valssien käytettävyys ja kunnossapito terästehtaassa

Valssi on valssauslaitteiston keskeinen komponentti. Valssauksessa aihiota muokataan kuljettamalla sitä kahden valssin muodostaman raon välistä. Valssit altistuvat valssausprosessissa korkealle lämpötilalle ja pintapaineelle. Valsseille asetettavat vaatimukset tiukkenevat tuottavuuden vaatimusten kiristyessä. Valssit, yhtenä valssauslaitteiston komponenteista, muodostavat suuren osan valssauksen kustannuksista, joten valssien käyttöiän pidentämisen avulla voidaan parantaa valssauksen tuottavuutta ja kustannustehokkuutta. Tässä tutkimuksessa tarkasteltiin valssien käytettävyyttä ja kunnossapitoa, sillä näitä asioita kehittämällä on mahdollista saavuttaa valsseille pidempi kestoikä. Tutkimus toteutettiin kirjallisuusselvityksenä, jota täydennettiin valssausta tekevien yritysten haastatteluilla. Tavoitteena oli kerätä saatavissa oleva kirjallinen ja hiljainen tieto yksiin kansiin ja tutkia mahdollisia syy-seuraussuhteita valssien käytettävyyteen vaikuttavien ilmiöiden sekä valssien kulumisen ja vaurioitumisen välillä. Tutkimuksessa havaittiin, että vauriotyypit ovat riippuvaisia valssausprosessista, jolla tarkoitetaan, että kuuma- ja kylmävalssauksessa esiintyy erilaisia vauriotyyppejä. Kuuma- ja kylmävalssauksessa myös valssien kulumiseen vaikuttavat erilaiset ilmiöt. Valssien kulumista ja vaurioita on mahdollista ehkäistä erilaisilla pintakäsittely- ja pinnoitusmenetelmillä. Valssien kunnossapidon toteutusta tutkittaessa havaittiin, että kuluneiden valssien vaihto kunnostettuihin pyritään suorittamaan mahdollisimman nopeasti ja tätä varten on saatavilla kyseiseen tarkoitukseen kehitettyjä laitteistoja. Kuluneet valssit sorvataan ja hiotaan, jotta niiden pinnasta saadaan tasainen ja saavutetaan haluttu halkaisija. Tämän jälkeen pinnoitusmenetelmiä on mahdollista suorittaa uudelleen. Kunnossapitotoimenpiteet tehdään joko yrityksen omalla korjaamolla tai alihankintana toisen yrityksen tiloissa.

Calucaltion of waste heat from hot rolled steel coils at SSAB and its recovery

Hot rolling process is heat input process. The heat energy in hot rolled steel coils can be utilized. At SSAB Strip Product Borlänge when the hot rolled steel coils came out of the hot rolling mill they are at the temperature range of 500°C to 800°C. Heat energy contained by the one hot rolled steel coil is about 1981Kwh whereas the total heat energy for the year 2008 is 230 GWh/year.The potential of heat is too much but the heat dissipation rate is too slow. Different factors on which heat dissipation rate depends are discussed.Three suggestions are proposed to collect the waste heat from hot rolled steel coils.The 2nd proposal in which water basin is suggested would help not only to collect the waste heat but to decrease in the cooling time.

Undersökning av steady state och utvärdering av valskraft och friktion vid kallvalsning av aluminium

The purpose with this thesis was to examine the cold rolling mill located at Högskolan Dalarna and to stabilize the rolling process, to achieve steady state. Experiments with cold rolling of an aluminium strip have given results for rolling force, friction, reduction, strip tension and strain hardening. Results show that steady state has been found for the experiments with roll force and strain hardening, and not been found for the experiments with friction and reduction. Results show that increased strip tension gives lower roll forces. The roll force equation of Stone shows comparable results with reality for dry contact with reductions up to 30 %, but starts being incomparable with higher reductions. The roll force equation of Stone shows a bit higher roll forces than reality gave, but was comparable within reductions from 13 to 50 %. Experiments have shown that the aluminium strip has gone through strain hardening. Experiments show how the set roll gap did not yield the desired thickness reduction, there for the elastic spring constant for the rolling mill was examined and determined to be 417 N / mm for the specific alloy band. The influence of tension strip for roll force was examined and Results confirm the theory about how the roll force is decreased by increasing tension strip. The work rolls started to slip against the alumina strip as high tension strip; 70 N/mm2, gave low roll force; < 15kN.

Finite element analysis of warpage in laminated aluminium alloy plates for machining of primary aeronautic parts

The aim of this paper consists in presenting a method of simulating the warpage in 7xxx series aluminium alloy plates. To perform this simulation finite element software MSC.Patran and MSC.Marc were used. Another result of this analysis will be the influence on material residual stresses induced on the raw material during the rolling process upon the warpage of primary aeronautic parts, fabricated through machining (milling) at Embraer. The method used to determinate the aluminium plate residual stress was Layer Removal Test. The numerical algorithm Modified Flavenot Method was used to convert layer removal and beam deflection in stress level. With such information about the level and profile of residual stresses become possible, during the step that anticipate the manufacturing to incorporate these values in the finite-element approach for modelling warpage parts. Based on that warpage parameter surely the products are manufactured with low relative vulnerability propitiating competitiveness and price. © 2007 American Institute of Physics.

Projeto de trocador de calor para uma máquina de aquecimento de vidro para laminação

The object of this study is a glass heating machine for rolling process, designed in 2006 and which is manufactured regularly. By customer request it is intended to increase the production capacity of this machine. However, initial tests have shown that the existing heat exchanger cannot supply the necessary thermal energy demand. A study of the thermal characteristics of the equipment was performed in order to obtain the required information to study alternatives for expanding its capacity taking into account space limitations and the need to rationalize costs, avoiding unnecessary oversizing

Análise do perfil de dureza e microestrutura de um aço forjado AISI A2 submetido a tratamento térmico com resfriamento em água

Due to the large use of steel in several processes around the world, there is the increasingly concern to find new materials and/or optimization and improvement of the processes, as the need to reduce the cost and a productivity increase in the primary industry, such as the siderurgy. The rolling is the most used mechanical process in the world and therefore is required the development of new tools in high volume and with optimum characteristics to support the market demand. Forged rolls used are for rolling. These rolls have heat treatment that has the purpose to achieve the appropriated mechanical properties to support the variables of the rolling process. The objective of this work is to analyze the hardness profile and the microstructure a tool steel similar to AISI A2, forged in an opened die process and submitted to heat treatment with water-cooling. The results allowed plotting a hardness profile and performing a microstructure analysis, and whereby to confirm that the heat treatment is not a quenching, but it is a material beneficiation by the hardening of superficial layer, since there is no martensitic microstructure. Therefore, this paper provides the support to future studies about the possibility to perform enhancements in this thermal heat made in the rolls produced at Gerdau Plant in Pindamonhangaba

Análise e comparação de orelhamento na liga AA3104 após laminação a quente

Aluminum has been widely used in the forming and manufacture of beverage cans, specific aluminum alloy AA3104, which manufacturers are increasingly demanding as to mechanical properties, quality and reducing waste. This work describes the analysis and comparison of the behavior of earing AA3104 aluminum alloy samples of final thicknesses of 1.80 and 2.10 mm. Were obtained after a hot rolling process, a total population of 86 samples for the two different thicknesses, of which 23 samples of 1.80 mm and 2.10 mm 63 samples. After removal of samples, there was a mechanical test inlay, then characterizing the earing in them. The results earing to the thicknesses of 1.80 and 2.10 mm were analyzed and compared statistically to give 7.1% and 7.4% on average, respectively, correlated with the hot rolling process variables, showing that they are statistically equal and that the process variables do not affect the end result desired, ranging from 7.0 to 7,5%

Projeto de trocador de calor para uma máquina de aquecimento de vidro para laminação

The object of this study is a glass heating machine for rolling process, designed in 2006 and which is manufactured regularly. By customer request it is intended to increase the production capacity of this machine. However, initial tests have shown that the existing heat exchanger cannot supply the necessary thermal energy demand. A study of the thermal characteristics of the equipment was performed in order to obtain the required information to study alternatives for expanding its capacity taking into account space limitations and the need to rationalize costs, avoiding unnecessary oversizing

Análise do perfil de dureza e microestrutura de um aço forjado AISI A2 submetido a tratamento térmico com resfriamento em água

Due to the large use of steel in several processes around the world, there is the increasingly concern to find new materials and/or optimization and improvement of the processes, as the need to reduce the cost and a productivity increase in the primary industry, such as the siderurgy. The rolling is the most used mechanical process in the world and therefore is required the development of new tools in high volume and with optimum characteristics to support the market demand. Forged rolls used are for rolling. These rolls have heat treatment that has the purpose to achieve the appropriated mechanical properties to support the variables of the rolling process. The objective of this work is to analyze the hardness profile and the microstructure a tool steel similar to AISI A2, forged in an opened die process and submitted to heat treatment with water-cooling. The results allowed plotting a hardness profile and performing a microstructure analysis, and whereby to confirm that the heat treatment is not a quenching, but it is a material beneficiation by the hardening of superficial layer, since there is no martensitic microstructure. Therefore, this paper provides the support to future studies about the possibility to perform enhancements in this thermal heat made in the rolls produced at Gerdau Plant in Pindamonhangaba