Langmuir and langmuir-blodgett films of polyfluorenes and their use in polymer light-emitting diodes

The Langmuir and Langmuir-Blodgett (LB) film properties of two polyfluorene derivatives, namely poly(2,7-9,9'-dihexylfluorene-dyil) (PDHF) and poly(9,9 dihexylfluorene-dyil-vynilene-alt-1,4-phenylene-vyninele) (PDHF-PV), are reported. Surface pressure (Pi-A) and surface potential (Delta V-A) isotherms indicated that PDHF-PV forms true monolayers at the air/water interface, but PDHF does not. LB films could be transferred onto various types of substrate for both PDHF and PDHF-PV. Only the LB films from PDHF-PV could withstand deposition of a layer of evaporated metal to form a light-emitting diode (PLED), which had typical rectifying characteristics and emitted blue light. It is inferred that the ability of the polymer to form true monomolecular layers at the air/water interface seems to be associated with the viability of the LB films in PLEDs.

Síntese de um novo polímero conjugado e reticulável e sua aplicação em células fotovoltaicas

Trabalho Final de Mestrado para obtenção do Grau de Mestre em Engenharia Química e Biológica

Polymer light emitting devices with Langmuir Blodgett (LB) films of a polyfluorene derivative

Polyfluorenes are promising materials for the emitting layer of polymer light emitting devices (PLEDs) with blue emission. In this work, we report on PLEDs fabricated with Langmuir-Blodgett (LB) films of a polyfluorene derivative, namely poly(9,9-di-hexylfluorenediyl vinylene-alt-1,4-phenylenevinylene) (PDHF-PV). Y-type LB films were transferred onto ITO substrates at a surface pressure of 35 mN m-1 and with dipping speed of 3 mm min -1. A thin aluminum layer was evaporated on top of the LB film, thus yielding a sandwich structure (ITO/PDHF-PV(LB)/Al). Current-voltage (I vs V) measurements indicate that the device displays a classical behavior of a rectifying diode. The threshold value is approximately 5 V, and the onset for visible light emission occurs at ca. 10 V. From the a.c. electrical responses we infer that the active layer has a typical behavior of PLEDs where the real component of ac conductivity obeys a power-law with the frequency. Cole-Cole plots (Im(Z) vs. Re(Z)) for the device exhibit a series of semicircles, the diameter of which decreases with increasing forward bias. This PLED structure is modeled by a parallel resistance and capacitance combination, representing the dominant mechanisms of charge transport and polarization in the organic layer, in series with a resistance representing the ITO contact. Overall, the results presented here demonstrate the feasibility of LEDs made with LB films of PDHF-PV.

Correlation Between Molecular Conformation, Packing, and Dynamics in Oligofluorenes: A Theoretical/Experimental Study

Fluorene-based systems have shown great potential as components in organic electronics and optoelectronics (organic photovoltaics, OPVs, organic light emitting diodes, OLEDs, and organic transistors, OTFTs). These systems have drawn attention primarily because they exhibit strong blue emission associated with relatively good thermal stability. It is well-known that the electronic properties of polymers are directly related to the molecular conformations and chain packing of polymers. Here, we used three oligofluorenes (trimer, pentamer, and heptamer) as model systems to theoretically investigate the conformational properties of fluorene molecules, starting with the identification of preferred conformations. The hybrid exchange correlation functional, OPBE, and ZINDO/S-CI showed that each oligomer exhibits a tendency to adopt a specific chain arrangement, which could be distinguished by comparing their UV/vis electronic absorption and C-13 NMR spectra. This feature was used to identify the preferred conformation of the oligomer chains in chloroform-cast films by comparing experimental and theoretical UV/vis and C-13 NMR spectra. Moreover, the oligomer chain packing and dynamics in the films were studied by DSC and several solid state NMR techniques, which indicated that the phase behavior of the films may be influenced by the tendency that each oligomeric chain has to adopt a given conformation.

Synthese und Strukturierung von Polymeren Halbleitern: Triphenylamine und Triazine

Zusammenfassung In der vorliegenden Arbeit konnte die neuartige Synthese von Triphyenylamin- und Triazin-Monomeren gezeigt werden. Die hergestellten Monomere konnten sowohl frei als auch lebend radikalisch polymerisiert werden, wodurch sich aus beiden Verbindungen Blockcopolymere herstellen ließen. Mittels GPC und DSC Messungen konnte die erhaltene Blockstruktur nachgewiesen werden. In Cyclovoltammetrie Messungen konnten die Elektronen-leitenden und Loch-leitenden Eigenschaften der Homopolymere nachgewiesen werden. Darüber hinaus war es mit diesen Messungen möglich, die Elektronen-leitenden und Loch-leitenden Blöcke dieser Blockcopolymere gezielt anzusprechen.Weiterhin wurden zwei neue Strukturierungsverfahren für Polymere entwickelt. In dem ersten Verfahren wurden dabei harte Siliziumstempel benutzt, so dass Strukturen im Nanometerbereich generiert werden konnten. Der gesamte Strukturierungsprozess konnte bei Raumtemperatur durchgeführt werden, was einen wesentlichen Zeitvorteil gegenüber NIL entspricht. Weiterhin wurden Linienstrukturen durch das Stempeln mit weichen Silikonstempeln hergestellt. Unabhängig ihrer Herstellungsmethode wirken diese Linienstrukturen als Orientierungsschichten für flüssigkristallines Polyfluoren, wobei die bis heute größte Fluoreszens-Anisotropie auf einem Lochleiter von 1:24 erhalten wurde. Somit sind OLEDs die polarisiertes Licht emittieren möglich.Im zweiten neuartigen Strukturierungsverfahren konnten getrennte Polymerstrukturen aus Loch- und Elektronenleitern durch Bestrahlen einer Monomermischung mit Licht erzeugt werden. Dieses Verfahren bietet den Vorteil, dass kein Material entfernt werden muss und die Strukturierung somit in einem Schritt erfolgt.

Liquid crystalline oligofluorenes and their derivatives

Homo-oligofluorenes (OFn), polyfluorenes (PF2/6) and oligofluorenes with one fluorenenone group in the center (OFnK) were synthesized. They were used as model compounds to understand of the structure-property relationships of polyfluorenes and the origin of the green emission in the photoluminescence (after photooxidation of the PFs) and the electroluminescence (EL) spectra. The electronic, electrochemical properties, thermal behavior, supramolecular self-assembly, and photophysical properties of OFn, PF2/6 and OFnK were investigated. Oligofluorenes with 2-ethylhexyl side chain (OF2-OF7) from the dimer up to the heptamer were prepared by a series of stepwise transition metal mediated Suzuki and Yamamoto coupling reactions. Polyfluorene was synthesized by Yamamoto coupling of 2,7-dibromo-9,9-bis(2-ethylhexyl)fluorene. Oligofluorenes with one fluorenone group in the center (OF3K, OF5K, OF7K) were prepared by Suzuki coupling between the monoboronic fluorenyl monomer, dimer, trimer and 2, 7-dibromofluorenone. The electrochemical and electronic properties of homo-oligofluorenes (OFn) were systematically studied by several combined techniques such as cyclic voltammetry, differential pulse voltammetry, UV-vis absorption spectroscopy, steady and time-resolved fluorescence spectroscopy. It was found that the oligofluorenes behave like classical conjugated oligomers, i.e., with the increase of the chain-length, the corresponding oxidation potential, the absorption and emission maximum, ionization potential, electron affinity, band gap and the photoluminescence lifetime displayed a very good linear relation with the reciprocal number of the fluorene units (1/n). The extrapolation of these linear relations to infinite chain length predicted the electrochemical and electronic properties of the corresponding polyfluorenes. The thermal behavior, single-crystal structure and supramolecular packing, alignment properties, and molecular dynamics of the homo-oligofluorenes (OFn) up to the polymer were studied using techniques such as TGA, DSC, WAXS, POM and DS. The OFn from tetramer to heptamer show a smectic liquid crystalline phase with clearly defined isotropization temperature. The oligomers do show a glass transition which exhibits n-1 dependence and allows extrapolation to a hypothetical glass transition of the polymer at around 64 °C. A smectic packing and helix-like conformation for the oligofluorenes from tetramer to heptamer was supported by WAXS experiments, simulation, and single-crystal structure of some oligofluorene derivatives. Oligofluorenes were aligned more easily than the corresponding polymer, and the alignability increased with the molecular length from tetramer to heptamer. The molecular dynamics in a series of oligofluorenes up to the polymer was studied using dielectric spectroscopy. The photophysical properties of OFn and PF2/6 were investigated by the steady-state spectra (UV-vis absorption and fluorescence spectra) and time-resolved fluorescence spectra both in solution and thin film. The time-resolved fluorescence spectra of the oligofluorenes were measured by streak camera and gate detection technique. The lifetime of the oligofluorenes decreased with the extension of the chain-length. No green emission was observed in CW, prompt and delayed fluorescence for oligofluorenes in m-THF and film at RT and 77K. Phosphorescence was observed for oligofluorenes in frozen dilute m-THF solution at 77K and its lifetime increased with length of oligofluorenes. A linear relation was obtained for triplet energy and singlet energy as a function of the reciprocal degree of polymerization, and the singlet-triplet energy gap (S1-T1) was found to decrease with the increase of degree of polymerization. Oligofluorenes with one fluorenone unit at the center were used as model compounds to understand the origin of the low-energy (“green”) emission band in the photoluminescence and electroluminescence spectra of polyfluorenes. Their electrochemical properties were investigated by CV, and the ionization potential (Ip) and electron affinity (Ea) were calculated from the onset of oxidation and reduction of OFnK. The photophysical properties of OFnK were studied in dilute solution and thin film by steady-state spectra and time-resolved fluorescence spectra. A strong green emission accompanied with a weak blue emission were obtained in solution and only green emission was observed on film. The strong green emission of OFnK suggested that rapid energy transfer takes place from higher energy sites (fluorene segments) to lower energy sites (fluorenone unit) prior to the radiative decay of the excited species. The fluorescence spectra of OFnK also showed solvatochromism. Monoexponential decay behaviour was observed by time-resolved fluorescence measurements. In addition, the site-selective excitation and concentration dependence of the fluorescence spectra were investigated. The ratio of green and blue emission band intensities increases with the increase of the concentration. The observed strong concentration dependence of the green emission band in solution suggests that increased interchain interactions among the fluorenone-containing oligofluorene chain enhanced the emission from the fluorenone defects at higher concentration. On the other hand, the mono-exponential decay behaviour and power dependence were not influenced significantly by the concentration. We have ruled out the possibility that the green emission band originates from aggregates or excimer formation. Energy transfer was further investigated using a model system of a polyfluorene doped by OFnK. Förster-type energy transfer took place from PF2/6 to OFnK, and the energy transfer efficiency increased with increasing of the concentration of OFnK. Efficient funneling of excitation energy from the high-energy fluorene segments to the low-energy fluorenone defects results from energy migration by hopping of excitations along a single polymer chain until they are trapped on the fluorenone defects on that chain or transferred onto neighbouring chains by Förster-type interchain energy transfer process. These results imply that the red-shifted emission in polyfluorenes can originate from (usually undesirable) keto groups at the bridging carbon atoms-especially if the samples have been subject to photo- or electro-oxidation or if fluorenone units are present due to an improper purification of the monomers prior to polymerization.

Poly(p-phenylen)-Derivate für die Anwendung in Leuchtdioden

Zusammenfassung Das 2,7-Polyfluoren (2,7-PF) wurde in neuer Zeit sowohl wegen seiner einfachen Synthese und hohen Fluoreszenzquantenausbeuten als auch seiner chemischen und thermischen Stabilität intensiv untersucht. Leider liegt das Emissionsmaximum von 2,7-PF in einem Bereich, bei dem das menschliche Auge nicht genügend Sensitivität aufweist. Das Leiter-Poly(p-phenylen) (LPPP) besitzt die optimale Wellenlänge. Jedoch zeigt das LPPP wegen seines steifen Rückgrates große Aggregationstendenz im Film auf, wodurch die Emissionsfarbe bathochrom verschoben und die Photolumineszenzquantenausbeute verringert wird. Es ist deshalb wünschenswert, Polymere zu synthetisieren, die eine längerwellige Emissionsbande als 2,7-PF und eine geringere Aggregationstendenz als LPPP 20 besitzen. Eine Reihe neuer blau emittierender Polymere auf der Basis von Indenofluoren- und Fluoren-Bausteinen mit geringer Aggregationstendenz, hoher thermischer und chemischer Stabilität sowie guter Verarbeitbarkeit wurden dargestellt. Die Polymere weisen eine hohe thermische Stabilität auf (Zersetzung ca.: 310 °C) und sind sehr gut löslich in organischen Lösungsmitteln. Das Absorptionsmaximum des 2,8-Polyindenofluoren (2,8-PIF) in Chloroform liegt bei 416 nm, das Emissionsmaximun bei 432 nm. Die Phasenumwandlungstemperatur beim PIF liegt ca. bei 260 °C. Leider zeigen 2,8-PIF Aggregationstendenzen im Film. Um die Aggregation komplett zu unterbinden, wurden Polyphenylene als Seitenketten an das Dibromfluoren angebracht. Anschließend wurde nach Yamamoto polymerisiert. Das dendritnische PF (DPF) weist die gleiche thermische Stabilität wie die PIFs 28 auf (Zersetzung: 340 °C). Das Polymer 62a ist sehr gut löslich in Toluol, Xylol und chlorierten organischen Lösungsmitteln. Die Absorptions- und Emissionsmaxima des DPFs in Lösung (Chloroform) weisen keine Veränderung gegenüber PF auf. Die Emissionsmaxima des DPFs im Film und nach dem Tempern (100 °C, 24 h) zeigen lediglich eine Verschiebung um 8 nm. Eine Aggregatenbande entsteht jedoch nicht. Dies unterstreicht die abschirmende Eigenschaft der dendritischen Substituenten. Durch Copolymerisation lassen sich die Eigenschaften von Polymeren variieren. Um die Aggregationstendenz der PIF-Derivate zu verringern, wurden die entsprechenden Monomere in verschiedenen Verhältnissen copolymerisiert. Durch die Copolymerisation wurde die PL-Quantenausbeute auf 50 % erhöht. Weiterhin wurden Copolymere von Indenofluoren und 9,10-Dibromanthracen, und erschiedenen Perylenen hergestellt, um zu blau, rot und grün emittierenden Polymeren zu gelangen. Alle blau emittierenden Polymeren wurden in Leuchtdioden untersucht. Das DPF und das Copolymer aus Indenofluoren und Anthracene wiesen die besten Eigenschaften hierfür auf.

Fluorenbasierende amphiphile Kammpolymere zur Ausbildung definierter Strukturen an Oberflächen und in Lösungen

Die Dissertation beschreibt die Darstellung und Charakterisierung von neuartigen, amphiphilen Carbazol- und Fluoren-(co)-polymeren, die infolge ihres strukturellen Aufbaus sowohl selbstorganisierende als auch optoelektronische Eigenschaften kombinierten. Zum einen wurden Kammpolymere mit konjugierten, steifen Rückgraten und flexiblen sowie konformativ schaltbaren Polyelektrolytseitenketten dargestellt und auf eine pH-abhängige Selbstorganisation in Lösung und an Oberflächen untersucht. Des Weiteren wurden neutrale, methanollösliche Polyfluorene synthetisiert, die in Kombination mit einem unpolaren Polyindenofluorenderivat zum Aufbau mehrschichtiger PLEDs mittels nasschemischer Verfahren eingesetzt wurden. Zum anderen fand die Synthese von amphiphilen Polyfluorenen statt, die als Emulgatoren zur Stabilisierung von inversen Emulsionen eingesetzt wurden. Dabei konnten mit Hilfe eines bereits für die Darstellung von anorganisch-organischen Kern-Schale-Partikeln etablierten in situ-Verfahrens formanisotrope, kristalline Zinkoxidkerne mit konjugierter Polymerhülle erhalten werden.