Main maximum power point tracking strategies intended for photovoltaics

This paper presents evaluations among the most usual MPPT techniques, doing meaningful comparisons with respect to the amount of energy extracted from the photovoltaic panel (PV) (Tracking Factor - TF) in relation to the available power, PV voltage ripple, dynamic response and use of sensors. Using MatLab/Simulink® and DSpace platforms, a digitally controlled boost DC-DC converter was implemented and connected to an Agilent Solar Array E4350B simulator in order to verify the analytical procedures. The main experimental results are presented and a contribution in the implementation of the IC algorithm is performed and called IC based on PI. Moreover, the dynamic response and the tracking factor are also evaluated using a Friendly User Interface, which is capable of online program power curves and compute the TF. Finally, a typical daily insulation is used in order to verify the experimental results for the main PV MPPT methods. © 2011 IEEE.

Evaluation of the main MPPT techniques for photovoltaic applications

This paper presents evaluations among the most usual maximum power point tracking (MPPT) techniques, doing meaningful comparisons with respect to the amount of energy extracted from the photovoltaic (PV) panel [tracking factor (TF)] in relation to the available power, PV voltage ripple, dynamic response, and use of sensors. Using MatLab/Simulink and dSPACE platforms, a digitally controlled boost dc-dc converter was implemented and connected to an Agilent Solar Array E4350B simulator in order to verify the analytical procedures. The main experimental results are presented for conventional MPPT algorithms and improved MPPT algorithms named IC based on proportional-integral (PI) and perturb and observe based on PI. Moreover, the dynamic response and the TF are also evaluated using a user-friendly interface, which is capable of online program power profiles and computes the TF. Finally, a typical daily insulation is used in order to verify the experimental results for the main PV MPPT methods. © 2012 IEEE.

Comparative analysis of MPPT techniques for PV applications

This paper presents a careful evaluation among the most usual MPPT techniques, doing meaningful comparisons with respect to the amount of energy extracted from the photovoltaic (PV) panel, PV voltage ripple, dynamic response and use of sensors, considering that the models are first implemented via MatLab/Simulink®, and after a digitally controlled boost DC-DC converter was implemented and connected to an Agilent Solar Array simulator in order to verify the simulation results. The prototype was built, the algorithms are digitally developed and the main experimental results are also presented, including dynamic responses and the experimental tracking factor (TF) for the analyzed MPPT techniques. © 2011 IEEE.

A comparative study of MPPT strategies and a novel singlephase integrated buck-boost inverter for small wind energy conversion systems

This paper presents the analysis of some usual MPPT (Maximum Power Point Tracking) strategies intended for small wind energy conversion (up to 1kW) based on permanent magnet synchronous generators (PMSG), considering the stand-alone application for a novel buck-boost integrated inverter. Each MPPT method is analytically introduced and then it is simulated using MatLab/Simulink considering standard conditions of wind and also commercially available turbines and generators. The extracted power in each case is compared with the maximum available power, so the tracking factor is calculated for each method. Thus, the focus is on the application to improve the efficiency of stand-alone wind energy conversion systems (WECS) with battery chargers and AC load supplied by inverter. Therefore, for this purpose a novel single phase buck-boost integrated inverter is introduced. Finally, the main experimental results for the introduced inverter are presented. © 2011 IEEE.

A new member of the ribbon-helix-helix transcription factor superfamily from the plant pathogen Xanthomonas axonopodis pv. citri

XACb0070 is an uncharacterized protein coded by the two large plasmids isolated from Xanthomonas axonopodis pv. cirri, the agent of citrus canker and responsible for important economical losses in citrus world production. XACb0070 presents sequence homology only with other hypothetical proteins belonging to plant pathogens, none of which have their structure determined. The NMR-derived solution structure reveals this protein is a homodimer in which each monomer presents two domains with different structural and dynamic properties: a folded N-terminal domain with beta alpha alpha topology which mediates dimerization and a long disordered C-terminal tail. The folded domain shows high structural similarity to the ribbon-helix-helix transcriptional repressors, a family of DNA-binding proteins of conserved 3D fold but low sequence homology: indeed XACb0070 binds DNA. Primary sequence and fold comparison of XACb0070 with other proteins of the ribbon-helix-helix family together with examination of the genes in the vicinity of xacb0070 suggest the protein might be the component of a toxin-antitoxin system. (C) 2010 Elsevier Inc. All rights reserved.

Soiling and other optical losses in solar-tracking PV plants in Navarra

Field data of soiling energy losses on PV plants are scarce. Furthermore, since dirt type and accumulation vary with the location characteristics (climate, surroundings, etc.), the available data on optical losses are, necessarily, site dependent. This paper presents field measurements of dirt energy losses (dust) and irradiance incidence angle losses along 2005 on a solar-tracking PV plant located south of Navarre (Spain). The paper proposes a method to calculate these losses based on the difference between irradiance measured by calibrated cells on several trackers of the PV plant and irradiance calculated from measurements by two pyranometers (one of them incorporating a shadow ring) regularly cleaned. The equivalent optical energy losses of an installation incorporating fixed horizontal modules at the same location have been calculated as well. The effect of dirt on both types of installations will accordingly be compared.

Energy payback time of grid connected pv systems: comparison between tracking and fixed systems

A review of existing studies about LCA of PV systems has been carried out. The data from this review have been completed with our own figures in order to calculate the Energy Payback Time of double and horizontal axis tracking and fixed systems. The results of this metric span from 2 to 5 years for the latitude and global irradiation ranges of the geographical area comprised between −10◦ to 10◦ of longitude, and 30◦ to 45◦ of latitude. With the caution due to the uncertainty of the sources of information, these results mean that a GCPVS is able to produce back the energy required for its existence from 6 to 15 times during a life cycle of 30 years. When comparing tracking and fixed systems, the great importance of the PV generator makes advisable to dedicate more energy to some components of the system in order to increase the productivity and to obtain a higher performance of the component with the highest energy requirement. Both double axis and horizontal axis trackers follow this way, requiring more energy in metallic structure, foundations and wiring, but this higher contribution is widely compensated by the improved productivity of the system.

Expression, crystallization and preliminary crystallographic analysis of PilZ(XAC1133) from Xanthomonas axonopodis pv. citri

Proteins containing PilZ domains are widespread in Gram-negative bacteria and have recently been shown to be involved in the control of biofilm formation, adherence, aggregation, virulence-factor production and motility. Furthermore, some PilZ domains have recently been shown to bind the second messenger bis(3'-> 5') cyclic diGMP. Here, the cloning, expression, purification and crystallization of PilZ(XAC1133), a protein consisting of a single PilZ domain from Xanthomonas axonopodis pv. citri, is reported. The closest PilZ(XAC1133) homologues in Pseudomonas aeruginosa and Neisseria meningitidis control type IV pilus function. Recombinant PilZ(XAC1133) containing selenomethionine was crystallized in space group P6(1). The unit-cell parameters were a = 62.125, b = 62.125, c = 83.543 angstrom. These crystals diffracted to 1.85 angstrom resolution and a MAD data set was collected at a synchrotron source. The calculated Matthews coefficient suggested the presence of two PilZ(XAC1133) molecules in the asymmetric unit.

Endocytosis of uncleaved tumor necrosis factor-alpha in macrophages

Activated monocytes and macrophages secrete the inflammatory cytokine tumor necrosis factor-alpha (TNF-alpha) TNF-alpha is produced as a 26 kd transmembrane protein that is cleaved to release a 17 kd soluble protein. TNF-alpha in both forms is biologically active. The intracellular trafficking of membrane-associated TNF-alpha in lipopolysaccharide-activated mouse macrophages was assessed after treatment with the metalloprotease inhibitor BB-3103, which prevents the cleavage of pro-TNF-alpha. Immunoprecipitation and immunofluorescence studies showed sustained expression of cell-associated TNF-alpha in the presence of the inhibitor. Cell immunoreactivity and surface biotinylation revealed that uncleaved TNF-alpha accumulated on the cell surface and was endocytosed, appearing in intracellular vesicles. Perturbation of post-Golgi traffic blocked the surface expression of 26 kd TNF-alpha. Tracking a bolus of TNF-alpha over time in cycloheximide-treated cells confirmed that uncleaved TNF-alpha is first transported to the cell surface and subsequently endocytosed. Vesicular structures immunoreactive for TNF-alpha were identified as endosomes by double labeling. The secretory and membrane-associated endocytic trafficking of TNF-alpha provides a mechanism for modulating the quantity of biologically active 26 kd TNF-alpha expressed on macrophages, allowing regulation of paracrine and autocrine responses.

A Step-up mu-Power Converter for Solar Energy Harvesting Applications, using Hill Climbing Maximum Power Point Tracking

This paper presents a step-up micro-power converter for solar energy harvesting applications. The circuit uses a SC voltage tripler architecture, controlled by an MPPT circuit based on the Hill Climbing algorithm. This circuit was designed in a 0.13 mu m CMOS technology in order to work with an a-Si PV cell. The circuit has a local power supply voltage, created using a scaled down SC voltage tripler, controlled by the same MPPT circuit, to make the circuit robust to load and illumination variations. The SC circuits use a combination of PMOS and NMOS transistors to reduce the occupied area. A charge re-use scheme is used to compensate the large parasitic capacitors associated to the MOS transistors. The simulation results show that the circuit can deliver a power of 1266 mu W to the load using 1712 mu W of power from the PV cell, corresponding to an efficiency as high as 73.91%. The simulations also show that the circuit is capable of starting up with only 19% of the maximum illumination level.

Fisioterapia e reabilitação em Portugal : o financiamento como factor crítico do desempenho

RESUMO - Num contexto em que a prestação de cuidados de Fisioterapia e Reabilitação é identificada como apresentando uma desigualdade e desajustamento da oferta regional superior à dos restantes cuidados de saúde, assim como uma falta de adequação dos preços praticados, perante as condições de oferta e procura actualmente existentes, o presente trabalho tem por objectivo investigar, no domínio do Desempenho, a influência do Financiamento na definição da prestação destes cuidados, tendo como pressuposto genérico que as decisões estratégicas e a reestruturação produtiva das organizações de saúde são condicionadas pelo sistema de preços. Considera-se que o actual sistema de Financiamento/Pagamento provoca um constrangimento na qualidade da resposta destes cuidados a dois níveis: um primeiro nível, ao colocar o pagamento no âmbito dos Meios Complementares de Diagnóstico e Terapêutica (MCDTs) a contratar pelo Serviço Nacional de Saúde, com isso determinando a configuração organizativa do sistema; um segundo nível de constrangimento que incide sobre as estruturas das organizações prestadoras, pela modelação que induz, nomeadamente a nível da sua produção. Na impossibilidade de tratar as duas dimensões do problema, pela falta de indicadores de desempenho deste sector, analisou-se, relativamente ao segundo nível de constrangimento, a produção de fisioterapia de três organizações que, potencialmente, teriam o mesmo o mesmo perfil de oferta por se enquadrarem num mesmo perfil de procura. Os resultados reflectem o pressuposto genérico do trabalho e abrem espaço para colocar como futura hipótese de investigação a razão da(s) causa(s) que poderão estar subjacentes à discrepância encontrada na média de tratamentos por sessão (duas vezes e meia) na produção das duas organizações que foi possível comparar.------------------- ABSTRACT - In a context where the provision of Physical Therapy and Rehabilitation care is identified as having a regional mismatch of supply and inequality above all the others health cares, and a lack of adequacy of prices in the current conditions of supply and demand, the present work has, as main purpose, to investigate, in the field of Performance, the Payment’s influence in shaping the provision of such health care. The general assumption tracking this analysis is that the strategic decisions on productive structure of health care organizations are influenced by the price systems. It is considered that the current Finance / Payment system causes two levels of constraints on the quality of such health care: a first constraint, as it putts its payment under the Supplementary Means of Diagnosis and Therapy (MCDTs), witch ends up establishing the organizational setup of the system; a second level of constraint by modelling the internal structure of these organizations. The lack of indicators characterizing the performance of this sector, addressed the present study to the second dimension, in witch was analysed the physical therapy production in three organizations that, potentially, would have the same profile of supply responding to similar characteristics of demand. The results reflect the above mentioned general assumption that supported the work, and leave an open space for future research, about the reason (s) that lay behind the discrepancy found between the average of treatments per session (two and a half times) in

PV inverters for module level applications

Dissertação para obtenção do Grau de Mestre em Energias Renováveis – Conversão Eléctrica e Utilização Sustentáveis

Análisis de la arquitectura de webs mediante tests de estrés de navegación, de usabilidad y eye tracking

Evaluar una arquitectura de la información en un sitio web ya desplegado no resulta una tarea sencilla. La mayoría de las técnicas se centran en examinar la usabilidad del sistema que, aunque afecta a la arquitectura de la información, no es el único factor que influye en ella. La principal técnica que se utiliza es el test de estrés de navegación. Se muestra un aporte metodológico para hacer dicha técnica más informativa, llevándola más allá de la simple anotación en papel por parte del usuario de respuestas a las preguntas de navegación planteadas. Se propone la combinación de ésta con otras técnicas de evaluación de la usabilidad: la técnica de pensar en voz alta o thinking aloud y un cuestionario de usabilidad. Se ha utilizado un sistema de seguimiento de la mirada o eye tracking para complementar la información obtenida mediante las técnicas aplicadas. El enfoque metodológico planteado se ha puesto a prueba analizando una serie de sitios web de bibliotecas de universidades públicas españolas. Se muestra en los resultados la validez del enfoque empleado, así como el valor que dicho enfoque y el uso del eye tracking aportan al análisis de la arquitectura de la información respecto al test de estrés de navegación tradicional.

PV-1: Leukocyte trafficking molecule and vascular marker

The distinction between lymphatic vessels and blood vessels is a crucial factor in many studies in immunology, vascular biology and cancer biology. They both share several characteristics and perform related, though different functions. They are equally important for the performance of the human immune system with the continuous recirculation of leukocytes from the tissues via lymphatics to the blood vessels and back into the tissue presenting the link between both systems. This study was undertaken to elucidate the differences in the gene expression between primary blood- and lymphatic endothelial cells as well as the two immortalized cell lines HMEC-1 (human microvascular endothelial cell line 1) and TIME (telomerase immortalized microvascular endothelial cell line). Furthermore, we wanted to investigate the mystery surrounding the identity of the antigen recognized by the prototype blood vascular marker PAL-E. In the last step we wanted to study whether the PAL-E antigen would be involved in the process of leukocyte migration from the bloodstream into the surrounding tissue. Our results clearly show that the gene expression in primary blood endothelial cells (BEC), lymphatic endothelial cells (LEC) and the cell lines HMEC-1 and TIME is plastic. Comparison of a large set of BEC- and LEC datasets allowed us to assemble a catalog of new, stable BEC- or LEC specific markers, which we verified in independent experiments. Additionally, several lines of evidence demonstrated that PAL-E recognizes plasmalemma vesicle associated protein 1 (PV-1), which can form complexes with vimentin and neuropilin-1. Finally, numerous in vitro and in vivo experiments identify the first function of the protein PV-1 during leukocyte trafficking, where it acts as regulatory molecule.

Exploring the impact of celebrity endorsement and product class involvement on advertising effectiveness: an eye tracking approach

Celebrity endorsement has increased in popularity over the past decades and companies are willing to spend increasingly excessive amounts of money into it. Even though multiple studies support celebrity endorsement, further research on its impact on advertising effectiveness is called for. Fur-ther, the role of consumers’ product class involvement in advertising needs to be further studied. The purpose of this study is to explore if consumers’ product class involvement and exposure to celebrity endorsers affect consumers brand recall. Supported by earlier studies, brand recall was used as a measure for advertising effectiveness in this study. In general, a psychological approach was chosen for building the theoretical framework. Concept of classical conditioning was presented in order to understand why people act how they do. Balanced theory and meaning transfer model were presented in order to study how celebrities can be used effectively in advertising context. Further, the importance of product class involvement in advertising effectiveness was evaluated. Hypotheses were formulated based on a literature review of the existing research. Because of the versatility of the research design, a mixed methods approach for this study was adopted. Empirical part of the study was conducted in three stages. First, a pre-test was conducted in order to choose suitable product endorsers for the advertisement stimuli used in the experiment. Second, an eye-tracking experiment with 30 test subjects was conducted in order to study how people view advertisements and whether the familiarity of the product endorser and consumers’ product class involvement affects brand recall. For the experiment, a fictional brand was created in order to avoid bias on brand recall. Third, qualitative interviews for 15 test subjects were conducted in the post-experiment stage in order to gain deeper understating of the phenomenon and to make sense of the findings from the experiment. Findings from this study support celebrity endorsement by suggesting that a famous spokesperson does not steal attention from brand information more than a non-celebrity product endorser. As a result, the use of a celebrity endorser did not decrease brand recall. Results support earlier research as consumer’ higher product class involvement resulted in a better brand recall. Findings from the interviews suggest that consumers have positive perceptions of celebrity endorsement in general. However, the celebrity–brand congruence is a crucial factor when creating attitudes towards the advertisement. Future research ideas were presented based on the limitations and results of this study