Effect of particle morphology on the mechanical and thermo-mechanical behavior of polymer composites

Fiber reinforced polymer composites have been used in many applications, such as in automobile, aerospace and naval industries, due basically to their high strength-to-weight and modulus-to-weight, among other properties. Even though particles are usually not able to lead to the level of reinforcement of fibers, particle reinforced polymer composites have been proposed for many new applications due to their low cost, easy fabrication and isotropic properties. In this work, polymer composites were prepared by incorporating glass particles of different morphologies on poly(aryl sulfones) matrices. Particles with aspect ratios equal to 1, 2.5 and 10 were used. The prepared composites were characterized using electron microscopy and thermal analysis. Mechanical properties of the composites were evaluated using a four-point bending test. The thermo-mechanical behavior of the obtained composites was also investigated. The results showed that the morphology of the particles alter significantly the mechanical properties of composites. Particles with larger values of aspect ratio led to large elastic modulus but low levels of strain at failure. This result was explained by modeling the thermo-mechanical behavior of the composites using a viscoelastic model. Parameters of the model, obtained from a Cole-Cole type of plot, demonstrated that interactions at the polymer-reinforcing agent interface were higher for composites with large aspect ratio particles. Higher levels of interactions at interfaces can lead to higher degrees of stress transfer and, consequently, to composites with large elastic modulus, as experimentally observed.

Effect of additives, precursors and process conditions on particle morphology

The objective of the thesis was to develop methods to manufacture and control calcium carbonate crystal nucleation and growth in precipitation process. The work consists of experimental part and literature part that addresses theory of nucleation, crystallization and precipitation. In the experimental part calcium carbonate was precipitated using carbonization reaction. Precipitation was carried out in presence of known morphology controlling agents (anionic polymers and sodium silicate) and by using different operation conditions. Formed material was characterized using SEM images, and its thermal stability was assessed. This work demonstrates that carbon dioxide feeding rate and concentrations of calcium hydroxide and additives can be used to control size, shape and amount of precipitating calcium carbonate.

Influence of particle morphology on nanostructural feature and conducting property in Sm-doped CeO2 sintered body

Doped ceria (CeO2,) compounds are fluorite type oxides, which show oxide ionic conductivity higher than yttria stabilized zirconia (YSZ), in oxidizing atmospheres. As a consequence of this, considerable interest has been shown in application of these materials for 'low (500-650 degreesC)' or 'intermediate (650-800 degreesC)' temperature operation, solid oxide fuel cells (SOFCs). In this study, the authors prepared two kinds of nanosize Sm-doped CeO2 particles with different morphologies: one type was round and the other was elongated. Processing these powders with different morphology produced dense materials with very different ionic conducting properties and different nanoscale microstructures. Since both particles are very fine and well dispersed, sintered bodies with high density (relative density >95% of theoretical) could be prepared using both types of powder particles. The electrical conductivity of sintered bodies prepared from these powders with different starting morphologies was very different. Materials prepared from particles having a round shape were much higher than those produced using powders with an elongated morphology. Measured activation energies of the corresponding sintered samples showed a similar trend; round particles (60 kJ/mol), elongated particles (74 kJ/mol). While X-ray diffraction (XRD) profiles of these sintered materials were identical, diffuse scatter was observed in the back.-round of selected area electron diffraction pattern recorded from both sintered bodies. This indicated an underlying structure that appeared to have been influenced by the processing technology. Detailed observation using high-resolution transmission electron microscopy (HR-TEM) revealed that the size of microdomain with ordering of cations in the sintered body made from round shape particles was much smaller than that of the sintered body made from elongated particles. Accordingly, it is concluded that the morphology of doped CeO2 powders strongly influenced the microdomain size and electrolytic properties in the doped CeO2 sintered body. (C) 2004 Elsevier B.V. All rights reserved.

Characterization Of Morphology And Composition Of Inorganic Fillers In Dental Alginates.

Energy dispersive X-ray spectroscopy microanalysis (EDX), scanning electron microscopy (SEM), and Archimedes' Principle were used to determine the characteristics of inorganic filler particles in five dental alginates, including Cavex ColorChange (C), Hydrogum 5 (H5), Hydrogum (H), Orthoprint (O), and Jeltrate Plus (JP). The different alginate powders (0.5 mg) were fixed on plastic stubs (n = 5) and sputter coated with carbon for EDX analysis, then coated with gold, and observed using SEM. Volume fractions were determined by weighing a sample of each material in water before and after calcining at 450(°)C for 3 h. The alginate materials were mainly composed of silicon (Si) by weight (C-81.59%, H-79.89%, O-78.87%, H5-77.95%, JP-66.88%, wt). The filler fractions in volume (vt) were as follows: H5-84.85%, JP-74.76%, H-70.03%, O-68.31%, and C-56.10%. The tested materials demonstrated important differences in the inorganic elemental composition, filler fraction, and particle morphology.

Inhalable particulate matter characterization in a medium-sized urban region in Brazil (São José dos Campos Town) - Part I: Morphology

In this study, the concentration and morphological characteristics of inhalable particulate material (PM10) were evaluated and associated with climatic conditions. The mean annual concentration was 11.0 µg m−3, varying between 0,647 µg m−3 and 36.8 µg m−3. Wind speed has a higher influence on PM10 dispersion, but direction was associated with particle source. During the wet period, wind speed is the main dispersion factor, while speed and direction both are important during the dry period. Based on the morphological characteristics, it is concluded that biogenic particles prevail during the rainy season and terrigenous particles during the dry period, depending on the wind direction and intensity.

Influence of solvent on the morphology and photocatalytic properties of ZnS decorated CeO2 nanoparticles

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Investigation of P3HT PCBM particle-based solar cells

Die Herstellung von Polymer-Solarzellen aus wässriger Phase stellt eine attraktive Alternative zu der konventionellen lösemittelbasierten Formulierung dar. Die Vorteile der aus wässriger Lösung hergestellten Solarzellen liegen besonders in dem umweltschonenden Herstellungsprozess und in der Möglichkeit, druckbare optoelektronische Bauteile zu generieren. Die Prozessierbarkeit von hydrophoben Halbleitern im wässrigen Milieu wird durch die Dispergierung der Materialien, in Form von Nanopartikeln, erreicht. Der Transfer der Halbleiter in eine Dispersion erfolgt über die Lösemittelverdampfungsmethode. Die Idee der Verwendung von partikelbasierte Solarzellen wurde bereits umgesetzt, allerdings blieben eine genaue Charakterisierung der Partikel sowie ein umfassendes Verständnis des gesamten Fabrikationsvorgangs aus. Deshalb besteht das Ziel dieser Arbeit darin, einen detaillierten Einblick in den Herstellungsprozess von partikelbasierten Solarzellen zu erlangen, mögliche Schwächen aufzudecken, diese zu beseitigen, um so zukünftige Anwendungen zu verbessern. Zur Herstellung von Solarzellen aus wässrigen Dispersionen wurde Poly(3-hexylthiophen-2,5-diyl)/[6,6]-Phenyl-C61-Buttersäure-Methylester (P3HT/PCBM) als Donor/Akzeptor-System verwendet. Die Kernpunkte der Untersuchungen richteten sich zum einen die auf Partikelmorphologie und zum anderen auf die Generierung einer geeigneten Partikelschicht. Beide Parameter haben Auswirkungen auf die Solarzelleneffizienz. Die Morphologie wurde sowohl spektroskopisch über Photolumineszenz-Messungen, als auch visuell mittels Elektronenmikroskopie ermittelt. Auf diese Weise konnte die Partikelmorphologie vollständig aufgeklärt werden, wobei Parallelen zu der Struktur von lösemittelbasierten Solarzellen gefunden wurden. Zudem wurde eine Abhängigkeit der Morphologie von der Präparationstemperatur beobachtet, was eine einfache Steuerung der Partikelstruktur ermöglicht. Im Zuge der Partikelschichtausbildung wurden direkte sowie grenzflächenvermittelnde Beschichtungsmethoden herangezogen. Von diesen Techniken hatte sich aber nur die Rotationsbeschichtung als brauchbare Methode erwiesen, Partikel aus der Dispersion in einen homogenen Film zu überführen. Des Weiteren stand die Aufarbeitung der Partikelschicht durch Ethanol-Waschung und thermische Behandlung im Fokus dieser Arbeit. Beide Maßnahmen wirkten sich positiv auf die Effizienz der Solarzellen aus und trugen entscheidend zu einer Verbesserung der Zellen bei. Insgesamt liefern die gewonnen Erkenntnisse einen detaillierten Überblick über die Herausforderungen, welche bei dem Einsatz von wasserbasierten Dispersionen auftreten. Die Anforderungen partikelbasierter Solarzellen konnten offengelegt werden, dadurch gelang die Herstellung einer Solarzelle mit einer Effizienz von 0.53%. Dieses Ergebnis stellt jedoch noch nicht das Optimum dar und lässt noch Möglichkeiten für Verbesserungen offen.

Three dimensional (3D) microstructure-based modeling of interfacial decohesion in particle reinforced metal matrix composites

Modeling and prediction of the overall elastic–plastic response and local damage mechanisms in heterogeneous materials, in particular particle reinforced composites, is a very complex problem. Microstructural complexities such as the inhomogeneous spatial distribution of particles, irregular morphology of the particles, and anisotropy in particle orientation after secondary processing, such as extrusion, significantly affect deformation behavior. We have studied the effect of particle/matrix interface debonding in SiC particle reinforced Al alloy matrix composites with (a) actual microstructure consisting of angular SiC particles and (b) idealized ellipsoidal SiC particles. Tensile deformation in SiC particle reinforced Al matrix composites was modeled using actual microstructures reconstructed from serial sectioning approach. Interfacial debonding was modeled using user-defined cohesive zone elements. Modeling with the actual microstructure (versus idealized ellipsoids) has a significant influence on: (a) localized stresses and strains in particle and matrix, and (b) far-field strain at which localized debonding takes place. The angular particles exhibited higher degree of load transfer and are more sensitive to interfacial debonding. Larger decreases in stress are observed in the angular particles, because of the flat surfaces, normal to the loading axis, which bear load. Furthermore, simplification of particle morphology may lead to erroneous results.

The morphology of spray-dried particles

Samples of Various industrial or pilot plant spray-dried materials were obtained from manufacturers together with details of drying conditions and feed concentrations. The samples were subjected to qualitative and semi-quantitative examination to identify structural and morphological features. The results were related to measured bulk physical properties and to drying conditions. Single particles were produced in a convective drying process Analogous to spray drying, in which different solids or mixtures of solids were dried from solutions, slurries or pastes as single suspended droplets. The localized chemical and physical structures were analysed and in some cases the retention of volatiles monitored. The results were related to experimental conditions, viz.; air temperature, initial solids concentration and the degree of feed aeration. Three distinct categories of particle morphology were identified, i.e.; crystalline, skin-forming and agglomerate. Each category is evidence of a characteristic drying behaviour which is dependent on initial solids concentration. the degree of feed aeration, and drying temperature. Powder flow ability, particle and bulk density, particle-size, particle friability, and the retention of volatiles bear a direct relationship to morphological structure. Morphologies of multicomponent mixtures were complex, but the respective migration rates of the solutes were dependent on drying temperature. Gas-film heat and SDSS transfer coefficients of single pure liquid droplets were also measured over a temperature range of 50•C to 200•C under forced convection. Balanced transfer rates were obtained attributed to droplet instability or oscillation within the airflow, demonstrated in associated work with single free-flight droplets. The results are of relevance to drier optimisation and to the optimisation of product characteristics, e.g.; particle strength and essential volatiles-retention, in convective drying.

A pragmatic approach for engineering porous mannitol and mechanistic evaluation of particle performance

The importance of mannitol has increased recently as an emerging diluent for orodispersible dosage forms. The study aims to prepare spray dried mannitol retaining high porosity and mechanical strength for the development of orally disintegrating tablets (ODTs). Aqueous feed of d-mannitol (10% w/v) comprising ammonium bicarbonate, NH4HCO3 (5% w/v) as pore former was spray dried at inlet temperature of 110-170°C. Compacts were prepared at 151MPa and characterized for porosity, hardness and disintegration time. Particle morphology and drying mechanisms were studied using thermal (HSM, DSC and TGA) and polymorphic (XRD) methods. Tablet porosity increased from 0.20±0.002 for pure mannitol to 0.53±0.03 using fabricated porous mannitol. Disintegration time dropped by 50-77% from 135±5.29s for pure mannitol to 75.33±2.52-31.67±1.53s for mannitol 110-170°C. Hardness increased by 150% at 110°C (258.67±28.89N) and 30% at 150°C (152.70±10.58N) compared to pure mannitol tablets (104.17±1.70N). Increasing inlet temperature resulted in reducing tablet hardness due to generation of 'micro-sponge'-like particles exhibiting significant elastic recovery. Impact of mannitol polymorphism on plasticity/elasticity cannot be ruled out as a mixture of α and β polymorphs formed upon spray drying.

Effect Of Spray Drying On The Sensory And Physical Properties Of Hydrolysed Casein Using Gum Arabic As The Carrier.

This study was aimed at spray drying hydrolysed casein using gum Arabic as the carrier agent, in order to decrease the bitter taste. Three formulations with differing proportions of hydrolysed casein: gum Arabic (10:90, 20:80 and 30:70) were prepared and characterized. They were evaluated for their moisture content, water activity, hygroscopicity, dispersibility in water and in oil, particle size and distribution, particle morphology, thermal behaviour (DSC) and bitter taste by a trained sensory panel using a paired-comparison test (free samples vs. spray dried samples). The proportion of hydrolysed casein did not affect the morphology of the microspheres. The spray drying process increased product stability and modified the dissolution time, but had no effect on the ability of the material to dissolve in either water or oil. The sensory tests showed that the spray drying process using gum Arabic as the carrier was efficient in attenuating or masking the bitter taste of the hydrolysed casein.

Produção de micropartículas de alginato contendo Flavobacterium columnare inativada pelo método de emulsão para vacinação de peixes por via oral

Alginate microparticles were prepared by an emulsion method aiming oral controlled release of antigens to fish. The effects of emulsification temperature and impeller type on particle morphology, average diameter, and size distribution were evaluated. Microparticles contaning formalin-killed Flavobacterium columnare cells (a model antigen) were prepared and characterized regarding bacterial release and particle stability when exposed to Nile tilapia (Oreochromis niloticus) typical gastrointestinal conditions. This methodology allowed the production of microparticles containing up to 14.3 g/L of bacterin, stable at a pH range from 2.0 to 9.0 for 12 h and smaller than 35 μm.

High Solids Content, Soap-Free, Film-Forming Latexes Stabilized by Laponite Clay Platelets

High solids content film-forming poly[styrene-co-(n-butyl acrylate)] [poly(Sty-co-BuA)] latexes armored with Laponite clay platelets have been synthesized by soap-free emulsion copolymerization of styrene and n-butyl acrylate. The polymerizations were performed in batch in the presence of Laponite and a methyl ether acrylateterminated poly(ethylene glycol) macromonomer in order to promote polymer/clay association. The overall polymerization kinetics showed a pronounced effect of clay on nucleation and stabilization of the latex particles. Cryo-transmission electron microscopy observation confirmed the armored morphology and indicated that the majority of Laponite platelets were located at the particle surface. The resulting nanostructured films displayed enhanced mechanical properties.

Orchid fleck symptoms may be caused naturally by two different viruses transmitted by Brevipalpus

Brevipalpus-transmitted viruses (BTV) cause chlorotic, necrotic and/or ringspot lesions in leaves and stems of orchids, citrus, coffee and several other plant species. There are two different types of BTVs, the nuclear and the cytoplasmic, based on maturation locale in the cell and particle morphology. The orchid fleck virus (OFV) is a BTV that infects orchids. Its short rodlike particles are 32-40 nm in diameter, 100-150 nm in length. OFV is found in the nucleus and is associated with intranuclear electronlucent viroplasms. In 1999, transmission electron microscopy analysis revealed a distinct type of virus causing orchid fleck symptoms. The bacilliform particles, 70-80 nm in diameter and 110-120 nm in length, induced electron-dense viroplasm inclusions in infected cells and resembled the cytoplasmic type associated with BTV, such as the citrus leprosis virus C. Our objective in the present study was to verify whether the cytoplasmic type virus found in orchids could be amplified using primers for other cytoplasmic BTVs, such as CiLV-C and Solanum violaefolium ringspot virus (SvRSV). Additionally, we aimed to differentiate the two BTVs found in orchids: the nuclear and the cytoplasmic types of OFV using microscopy and molecular and serological tools. This virus was not amplified by the CiLV-C and SvRSV primers, and neither the molecular nor the serological tools available to the OFV diagnosis reacted with it, demonstrating that they are definitely different viruses.

Preparation and characterization of D, L-PLA loaded 17-beta-Estradiol valerate by emulsion/evaporation methods

PLA microparticles containing 17-beta-estradiol valerate were prepared by an emulsion/evaporation method in order to sustain drug release. This system was characterized concerning particle size, particle morphology and the influence of formulation and processing parameters on drug encapsulation and in vitro drug release. The biodegradation of the microparticles was observed by tissue histological analysis. Scanning electron microscopy and particle size analysis showed that the microparticles were spherical, presenting non-aggregated homogeneous surface and had diameters in the range of 718-880 nm (inert microparticles) and 3-4 mu m (drug loaded microparticles). The encapsulation efficiency was similar to 80%. Hormone released from microparticles was sustained. An in vivo degradation experiment confirmed that microparticles are biodegradable. The preparation method was shown to be suitable, since the morphological characteristics and efficiency yield were satisfactory. Thus, the method of developed microparticles seems to be a promising system for sustained release of 17-beta-estradiol.