Numerical simulations of the effects of residual stresses in adhesively bonded composite specimen

In this work the problem of performing a numerical simulation of quasi-static crack propagation within an adhesive layer of a bonded joint under Mode I loading affected by stress field changes due to thermal-chemical shrinkage induced by cure process is addressed. Secondly, a parametric study on fracture critical energy, cohesive strength and Young's modulus is performed. Finally, a particular case of adhesive layer stiffening is simulated in order to verify qualitatively the major effect.

Experimental and numerical simulation of the use of fiber reinforced composite materials for road side safety applications /

"May 1997."

Probabilistic stress variation studies on composite single lap joint using Monte Carlo simulation

The work presented in this paper involves the stochastic finite element analysis of composite-epoxy adhesive lap joints using Monte Carlo simulation. A set of composite adhesive lap joints were prepared and loaded till failure to obtain their strength. The peel and shear strain in the bond line region at different levels of load were obtained using digital image correlation (DIC). The corresponding stresses were computed assuming a plane strain condition. The finite element model was verified by comparing the numerical and experimental stresses. The stresses exhibited a similar behavior and a good correlation was obtained. Further, the finite element model was used to perform the stochastic analysis using Monte Carlo simulation. The parameters influencing stress distribution were provided as a random input variable and the resulting probabilistic variation of maximum peel and shear stresses were studied. It was found that the adhesive modulus and bond line thickness had significant influence on the maximum stress variation. While the adherend thickness had a major influence, the effect of variation in longitudinal and shear modulus on the stresses was found to be little. (C) 2014 Elsevier Ltd. All rights reserved.

Numerical Simulation of Transient Thermal Field and Residual Stress in Laser Melting Process

以激光熔凝表面强韧化处理为背景,应用空间弹塑性有限单元和高精度数值算法同时考虑材料组织性能的变化模拟工件的温度场及残余应力,研究激光熔凝加工中瞬时温度场及残余应力数值模拟,同时考虑相变潜热及相变塑性的影响,用算例验证了模型的正确性,给出了不同时刻温度场分布及残余应力分布。

Residual Stress And Deformation Analysis Of Anodic Bonded Multi-Layer Of Glass And Aluminum

The bonding of glass wafer to aluminum foils in multi-layer assemblies was made by the common anodic bonding process. The bonding was performed at temperatures in the range 350-450 degrees C and with an applied voltage in the range 400-700 V under a pressure of 0.05 MPa. Residual stress and deformation in samples of two-layer (aluminum/glass) and three-layer (glass/aluminum/glass) were analyzed by nonlinear finite element simulation software MARC. The stress and strain varying with cooling time were obtained. The analyzed results show that deformation of the three-layer sample is significantly smaller than that of the two-layer sample, because of the symmetric structure of the three-layer sample. This has an important advantage in MEMS fabrication. The maximum equivalent stresses locate in the transition layer in both samples, which will become weakness in bonded sample.

Influence of friction during forming processes-a study using a numerical simulation technique

Friction has an important influence in metal forming operations, as it contributes to the success or otherwise of the process. In the present investigation, the effect of friction on metal forming was studied by simulating compression tests on cylindrical Al-Mg alloy using the finite element method (FEM) technique. Three kinds of compression tests were considered wherein a constant coefficient of friction was employed at the upper die-work-piece interface. However, the coefficient of friction between the lower die-work-piece interfaces was varied in the tests. The simulation results showed that a difference in metal flow occurs near the interfaces owing to the differences in the coefficient of friction. It was concluded that the variations in the coefficient of friction between the dies and the work-piece directly affect the stress distribution and shape of the work-piece, having implications on the microstructure of the material being processed.

Analysis of residual stress gradient in MEMS multi-layer structure

Residual stress and its gradient through the thickness are among the most important properties of as-deposited films. Recently, a new mechanism based on a revised Thomas-Fermi-Dirac (TFD) model was proposed for the origin of intrinsic stress in solid film

The influence of residual stress on a roll forming process

Roll forming is increasingly used in the automotive industry to form High Strength Steel (HSS) and Advanced High Strength Steel (AHSS) for structural components. Because of the large variety of applications of roll forming in the industry, Finite Element Analysis (FEA) is increasingly utilized for roll forming process design. Bending is the dominant deformation mode in roll forming and sheet materials used in the process are often temper rolled (skin passed), roller- or tension-levelled. These processes introduce residual stresses into the material, and recent studies have shown that those affect the material behaviour in bending. A thickness reduction rolling process available at Deakin that leads to material deformation similar to an industrial temper rolling operation was used in this study to introduce residual stresses into a dual phase, DP780, steel strip. The initial and thickness reduced strips were then used in a 5-stand experimental V-section roll forming set-up to identify the effect of residual stress on the final shape. The influence of residual stress and the effect of plastic deformation on the material behaviour in roll forming are separately determined in numerical simulation. The results show that the thickness reduction rolling process decreases the maximum bow height while the springback angle and end flare increase. Comparison with experimental results shows that using material data from the conventional tensile test in a numerical simulation does not allow for the accurate prediction of shape defects in a roll forming process if a residual stress profile exists in the material. On the other hand including the residual stress information leads to improved model accuracy.

NUMERICAL SIMULATION of THE BEHAVIOR of THE BEHAVIOR of REINFORCED CONCRETE BEAMS and COLUMNS BY FEM CAASTEM 2000 PROGRAM

The objective of this paper is the numerical study of the behavior of reinforced concrete beams and columns by non-linear numerical simulations. The numerical analysis is based on the finite element method implemented in CASTEM 2000. This program uses the constitutive elastoplastic perfect model for the steel, the Drucker-Prager model for the concrete and the Newton-Raphson for the solution of non-linear systems. This work concentrates on the determination of equilibrium curves to the beams and force-strain curves to the columns. The numeric responses are confronted with experimental results found in the literature in order to check there liability of the numerical analyses.

Use of the energy-release rate in a 2 scale damage analysis of a bonded joint

Stress singularities appear at the extremities of an adhesive bond. They can produce a damage mechanism that we assimilate in this Note to a crack. The energy release rate permits to characterize its evolution. But a very refined mesh would be necessary for a real structure. Using an asymptotic method based on the small thickness of the bond a limit model with a different local behaviour is suggested. It leads to an approximation of the energy release rate

Numerical simulation of the edge stress singularity and the adhesion strength for compliant mushroom fibrils adhered to rigid substrates

Open Access funded by European Research Council Acknowledgements RB thanks GRADUS, Faculty 8.4. Natural Sciences, of Saarland University for partially funding his research visit to the University of California, Santa Barbara. RB would also thank to Dr. S. Khaderi for his help in setting up the model. He also thanks Dr. R. Hensel and Dr. N. Guimard for fruitful discussions and for their continuous support. EA acknowledges funding from the European Research Council under the European Union's Seventh Framework Program (FP/2007-2013)/ERC Advanced Grant no. 340929.

Analysis of the moisture effect on the mechanical behaviour of an adhesively bonded joint under proportional multi-axial loads

The objective of the study is to identify the 3D behaviour of an adhesive in an assembly, and to take into account the effect of ageing in a marine environment. To that end, three different tests were employed. Gravimetric analyses were used to determine the water diffusion kinetics in the adhesive. Bulk tensile tests were performed to highlight the effects of humid ageing on the adhesive behaviour. Modified Arcan tests were performed for several ageing times to obtain the experimental database which was necessary to identify constitutive models. A Mahnken-Schlimmer type model was determined for the unaged state according to a procedure developed in a previous study. This identification used inverse techniques. It was based on the unaged modified Arcan results and on a coupling between an optimisation routine and finite-element analysis. Then, a global inverse identification procedure was developed. Its aim was to relate the unaged parameters to the moisture concentration and overcome the difficulties usually associated with ageing of bonded assemblies in a humid environment: a non-uniformity of the stress state and a gradient of mechanical properties in the adhesive. This procedure was similar to the one used in the first part but needed modified Arcan results for several ageing times. It also required an initial assumption for the evolution of the Mahnken-Schlimmer parameters with the moisture concentration.

Numerical simulation of strain-adaptive bone remodelling in the ankle joint

Background: The use of artificial endoprostheses has become a routine procedure for knee and hip joints while ankle arthritis has traditionally been treated by means of arthrodesis. Due to its advantages, the implantation of endoprostheses is constantly increasing. While finite element analyses (FEA) of strain-adaptive bone remodelling have been carried out for the hip joint in previous studies, to our knowledge there are no investigations that have considered remodelling processes of the ankle joint. In order to evaluate and optimise new generation implants of the ankle joint, as well as to gain additional knowledge regarding the biomechanics, strain-adaptive bone remodelling has been calculated separately for the tibia and the talus after providing them with an implant. Methods: FE models of the bone-implant assembly for both the tibia and the talus have been developed. Bone characteristics such as the density distribution have been applied corresponding to CT scans. A force of 5,200 N, which corresponds to the compression force during normal walking of a person with a weight of 100 kg according to Stauffer et al., has been used in the simulation. The bone adaptation law, previously developed by our research team, has been used for the calculation of the remodelling processes. Results: A total bone mass loss of 2% in the tibia and 13% in the talus was calculated. The greater decline of density in the talus is due to its smaller size compared to the relatively large implant dimensions causing remodelling processes in the whole bone tissue. In the tibia, bone remodelling processes are only calculated in areas adjacent to the implant. Thus, a smaller bone mass loss than in the talus can be expected. There is a high agreement between the simulation results in the distal tibia and the literature regarding. Conclusions: In this study, strain-adaptive bone remodelling processes are simulated using the FE method. The results contribute to a better understanding of the biomechanical behaviour of the ankle joint and hence are useful for the optimisation of the implant geometry in the future.

An inverse routine to predict residual stress in sheet material

A method is presented to determine residual stress distribution in sheet material from data collected in a free bending test. It may be used where the residual stress distribution is symmetrical about the mid-surface as it is usually the case for frequently-used sheet metal post-processing techniques such as skin-pass or temper rolling, tension- and roller leveling. An existing inverse technique is used to obtain a residual stress profile and material constants that provide the best fit in a finite element analysis of bending with the experimentally derived moment-curvature relation. The method is verified for bending of a low-carbon stainless steel using measurement of residual stress by X-ray diffraction. The residual stresses were induced in the sheet by cold rolling. The technique described here can be used industrially as a rapid method of investigating residual stresses in incoming sheet. In processes where the deformation is principally one of bending, such as cold roll forming, it is known that residual stresses have an influence on shape defects and springback and the method presented here can be used to determine whether incoming sheet is suitable for further processing and also as a means of obtaining improved material data input for numerical simulation.