Efeito nernst anômalo em Materiais com anisotropia magnetocristalina (110)

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Eletrodo de hidrogênio: o que há nos livros didáticos além de E¸ = 0?

The results of an exercise on electrochemistry for General Chemistry students are presented. The difficulty encountered by students in predicting the shift in the potential of the hydrogen electrode under non-standard conditions prompted a search in textbooks on how the subject is developed. Besides several instances of inconsistencies in defining the standard state, such as including the temperature in the definition, a number of incorrect depictions of the hydrogen electrode were discovered. Of the 28 General Chemistry books, 16 Physical Chemistry books and 24 Internet pages, 30, 20 and 46%, respectively, showed devices that would not work in practice.

Periodic electric field enhanced transport through membranes

We examine the mean flux across a homogeneous membrane of a charged tracer subject to an alternating, symmetric voltage waveform. The analysis is based on the Nernst-Planck flux equation, with electric field subject to time dependence only. For low frequency electric fields the quasi steady-state flux can be approximated using the Goldman model, which has exact analytical solutions for tracer concentration and flux. No such closed form solutions can be found for arbitrary frequencies, however we find approximations for high frequency. An approximation formula for the average flux at all frequencies is also obtained from the two limiting approximations. Numerical integration of the governing equation is accomplished by use of the numerical method of lines and is performed for four different voltage waveforms. For the different voltage profiles, comparisons are made with the approximate analytical solutions which demonstrates their applicability. (c) 2005 Elsevier B.V. All rights reserved.

Odorant-induced currents in intact patches from rat olfactory receptor neurons: Theory and experiment

Odorant-induced currents in mammalian olfactory receptor neurons have proved difficult to obtain reliably using conventional whole-cell recording. By using a mathematical model of the electrical circuit of the patch and rest-of-cell, we demonstrate how cell-attached patch measurements can be used to quantitatively analyze responses to odorants or a high (100 mM) K+ solution. High K+ induced an immediate current flux from cell to pipette, which was modeled as a depolarization of similar to 52 mV, close to that expected from the Nernst equation (56 mV), and no change in the patch conductance. By contrast, a cocktail of cAMP-stimulating odorants induced a current flux from pipette into cell following a significant (4-10 s) delay. This was modeled as an average patch conductance increase of 36 pS and a depolarization of 13 mV, Odorant-induced single channels had a conductance of 16 pS. In cells bathed with no Mg2+ and 0.25 mM Ca2+, odorants induced a current flow from cell to pipette, which was modeled as a patch conductance increase of similar to 115 pS and depolarization of similar to 32 mV, All these results are consistent with cAMP-gated cation channels dominating the odorant response, This approach, which provides useful estimates of odorant-induced voltage and conductance changes, is applicable to similar measurements in any small cells.

Effective Electrodiffusion equation for non uniform nanochannels

We derive a one dimensional formulation of the Planck-Nernst-Poisson equation to describe the dynamics of of a symmetric binary electrolyte in channels whose section is of nanometric section and varies along the axial direction. The approach is in the spirit of the Fick-Jacobs di fusion equation and leads to a system of coupled equations for the partial densities which depends on the charge sitting at the walls in a non trivial fashion. We consider two kinds of non uniformities, those due to the spatial variation of charge distribution and those due to the shape variation of the pore and report one and three-dimensional solutions of the electrokinetic equations.

Accounting for adsorption and desorption in Lattice Boltzmann simulations

We report a Lattice-Boltzmann scheme that accounts for adsorption and desorption in the calculation of mesoscale dynamical properties of tracers in media of arbitrary complexity. Lattice Boltzmann simulations made it possible to solve numerically the coupled Navier-Stokes equations of fluid dynamics and Nernst-Planck equations of electrokinetics in complex, heterogeneous media. With the moment propagation scheme, it became possible to extract the effective diffusion and dispersion coefficients of tracers, or solutes, of any charge, e.g., in porous media. Nevertheless, the dynamical properties of tracers depend on the tracer-surface affinity, which is not purely electrostatic and also includes a species-specific contribution. In order to capture this important feature, we introduce specific adsorption and desorption processes in a lattice Boltzmann scheme through a modified moment propagation algorithm, in which tracers may adsorb and desorb from surfaces through kinetic reaction rates. The method is validated on exact results for pure diffusion and diffusion-advection in Poiseuille flows in a simple geometry. We finally illustrate the importance of taking such processes into account in the time-dependent diffusion coefficient in a more complex porous medium.

Uma abordagem robusta de cálculo aplicada a um sistema potenciométrico de medida de concentrações hidrogeniônicas em soluções aquosas

The data analyzed in this work were generated following the methodology developed by Molina et al.(J. Electroanal. Chem., 1979) for the calibration of a potentiometric system of measurement of hydrogen-ion concentrations resulting from neutralizations, at 25 ºC, of acidic or alkaline solutions at constant ionic strength (0.1 mol.l-1) held with NaClO4. The observed data present a serious deviation in relation to the mathematical model derived from the Nernst equation, for pH values ranging from 3 to 11, where pH=-log[H+]. We show that the minimization of the sum of the absolute values of the residuals gives estimates that are not influenced by outlying values.

Eletrodo de hidrogênio: o que há nos livros didáticos além de E¸ = 0?

The results of an exercise on electrochemistry for General Chemistry students are presented. The difficulty encountered by students in predicting the shift in the potential of the hydrogen electrode under non-standard conditions prompted a search in textbooks on how the subject is developed. Besides several instances of inconsistencies in defining the standard state, such as including the temperature in the definition, a number of incorrect depictions of the hydrogen electrode were discovered. Of the 28 General Chemistry books, 16 Physical Chemistry books and 24 Internet pages, 30, 20 and 46%, respectively, showed devices that would not work in practice.

Utilização de um eletrodo de grafite recoberto com PbO2 incorporado em matriz de PVC como eletrodo indicador em titulações coulométricas

A aplicação de um eletrodo sensível a íons H3O+, obtido pelo recobrimento de um eletrodo de grafite com uma membrana polimérica contendo PbO2 incorporado em uma matriz de PVC (PbO2-PVC), como eletrodo indicador em titulações coulométricas de neutralização, foi investigada. As leituras dos potenciais foram feitas usando o eletrodo indicador de PbO2-PVC e para comparação dos resultados foi usado um eletrodo de vidro combinado (EVC). As curvas de titulação monitoradas com o eletrodo de PbO2-PVC apresentaram características semelhantes àquelas monitoradas com o EVC e os tempos de equivalência obtidos foram concordantes a um nível de confiança de 95%. O eletrodo de PbO2-PVC apresentou resposta linear no intervalo de pH 2 a 12 com inclinação de Nernst de -57,6 ± 0,1 mV/pH (r= 0,9998), sendo o tempo de resposta deste eletrodo bem menor do que aquele obtido com o EVC. O eletrodo de PbO2-PVC é de fácil construção, possui baixo custo e tempo de vida útil superior a 4 meses, equivalente a (pelo menos 1200 determinações por membrana polimérica).

Modelling of potentiometric ion sensors

Potentiometric ion sensors are a very important subgroup of electrochemical sensors, very attractive for practical applications due to their small size, portability, low-energy consumption, relatively low cost and not changing the sample composition. They are investigated by the researchers from many fields of science. The continuous development of this field creates the necessity for a detailed description of sensor response and the electrochemical processes important in the practical applications of ion sensors. The aim of this thesis is to present the existing models available for the description of potentiometric ion sensors as well as their applicability and limitations. This includes the description of the diffusion potential occurring at the reference electrodes. The wide range of existing models, from most idealised phase boundary models to most general models, including migration, is discussed. This work concentrates on the advanced modelling of ion sensors, namely the Nernst-Planck-Poisson (NPP) model, which is the most general of the presented models, therefore the most widely applicable. It allows the modelling of the transport processes occurring in ion sensors and generating the potentiometric response. Details of the solution of the NPP model (including the numerical methods used) are shown. The comparisons between NPP and the more idealized models are presented. The applicability of the model to describe the formation of diffusion potential in reference electrode, the lower detection limit of both ion-exchanger and neutral carrier electrodes and the effect of the complexation in the membrane are discussed. The model was applied for the description of both types of electrodes, i.e. with the inner filling solution and solidcontact electrodes. The NPP model allows the electrochemical methods other than potentiometry to be described. Application of this model in Electrochemical Impedance Spectroscopy is discussed and a possible use in chrono-potentiometry is indicated. By combining the NPP model with evolutionary algorithms, namely Hierarchical Genetic Strategy (HGS), a novel method allowing the facilitation of the design of ion sensors was created. It is described in detail in this thesis and its possible applications in the field of ion sensors are indicated. Finally, some interesting effects occurring in the ion sensors (i.e. overshot response and influence of anionic sites) as well as the possible applications of NPP in biochemistry are described.

Water and electrolyte content and distribution in tissues of thermally-acclimated rainbow trout, Salmo gairdneri

The primary objective of this investigation was that of providing a comprehensive tissue-by-tissue assessment of water-electrolyte status in thermally-acclimated rainbow trout, Salmo gairdneri. To this end levels of water and the major ions, sodium, chloride and potassium were evaluated in the plasma, at three skeletal muscle sites, and in cardiac muscle, liver, spleen, gut and brain of animals acclimated to 2°, 10° and 18°C. The occurrence of possible seasonal variations in water-electrolyte balance was evaluated by sampling sununer and late fall-early winter populations of trout. On the basis of values for water and electrolyte content, estimates of extracellular and cellular phase volumes, cellular electrolyte concentrations and Nernst equilibrium potentials were made. Since accurate assessment of the extracellular phase volume is critical in the estimation of cellular electrolyte concentrations and parameters based on assumed cellular ion levels, [14 C]-polyethylene glycol-4000, which is assumed to be confined to the extracellular space, was employed to provide comparisons with various ion-defined spaces (H20~~s, H20~~/K and H20~~s). Subsequently, the ion-defined space yielding the most realistic estimate of extracellular phase volume for each tissue was used in cellular electrolyte calculations. Water and electrolyte content and distribution varied with temperature. Tissues, such as liver, spleen and brain appeared to be the most thermosensitive, whereas skeletal and cardiac muscle and gut tissue were less influenced. 'Summer' series trout appeared to be more capable of maintaining their water- electrolyte balance than the ~fall-winter' series animals. i The data are discussed in terms of their possible effect on maintenance of appropriate cellular metabolic and electrophysiological functions.

The effect of oxygen and parenteral nutrition on the redox potential and bronchopulmonary dysplasia in extremely preterm infants

Introduction: Le supplément d’oxygène et la nutrition parentérale (NP) sont les deux sources majeures de stress oxydant chez le nouveau-né. Lors de la détoxification des oxydants, le potentiel redox du glutathion s’oxyde. Notre hypothèse est que le supplément d’oxygène et la durée de la NP sont associés à un potentiel redox plus oxydé et à une augmentation de la sévérité de la dysplasie bronchopulmonaire (DBP). Patients et Méthodes: Une étude observationnelle prospective incluant des enfants de moins de 29 semaines d’âge gestationnel. Les concentrations sanguines de GSH et GSSG à jour 6-7 et à 36 semaines d’âge corrigé étaient mesurées par électrophorèse capillaire et le potentiel redox était calculé selon l’équation de Nernst. La sévérité de la DBP correspondait à la définition du NICHD. Résultats: Une FiO2≥ 25% au 7ième jour de vie ainsi que plus de 14 jours de NP sont significativement associés à un potentiel redox plus oxydé et à une DBP plus sévère. Ces relations sont indépendantes de l’âge de gestation et de la gravité de la maladie initiale. La corrélation entre le potentiel redox et la sévérité de la DBP n’est pas significative. La durée de la NP était responsable de 15% de la variation du potentiel redox ainsi que de 42% de la variation de la sévérité de la DPB. Conclusion: Ces résultats suggèrent que l’oxygène et la NP induisent un stress oxydant et que les stratégies visant une utilisation plus judicieuse de l’oxygène et de la NP devraient diminuer la sévérité de la DBP.

Transport coefficients, Raman spectroscopy, and computer simulation of lithium salt solutions in an ionic liquid

Lithium salt solutions of Li(CF3SO2)(2)N, LiTFSI, in a room-temperature ionic liquid (RTIL), 1-butyl-2,3-dimethyl-imidazolium cation, BMMI, and the (CF3SO2)(2)N-, bis(trifluoromethanesulfonyl)imide anion, [BMMI][TFSI], were prepared in different concentrations. Thermal properties, density, viscosity, ionic conductivity, and self-diffusion coefficients were determined at different temperatures for pure [BMMI][TFSI] and the lithium solutions. Raman spectroscopy measurements and computer simulations were also carried out in order to understand the microscopic origin of the observed changes in transport coefficients. Slopes of Walden plots for conductivity and fluidity, and the ratio between the actual conductivity and the Nernst-Einstein estimate for conductivity, decrease with increasing LiTFSI content. All of these studies indicated the formation of aggregates of different chemical nature, as it is corroborated by the Raman spectra. In addition, molecular dynamics (MD) simulations showed that the coordination of Li+ by oxygen atoms of TFSI anions changes with Li+ concentration producing a remarkable change of the RTIL structure with a concomitant reduction of diffusion coefficients of all species in the solutions.

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as molten carbonate fuel cell (MCFC) operates at high temperatures. Thus, cogeneration processes may be performed, generating heat for its own process or for other purposes of steam generation in the industry. The use of ethanol is one of the best options because this is a renewable and less environmentally offensive fuel, and is cheaper than oil-derived hydrocarbons, as in the case of Brazil. In that country, because of technical, environmental, and economic advantages, the use of ethanol by steam reforming process has been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where the highest volumes of products are produced, making possible a higher production of energy, that is, a more efficient use of resources. To attain this objective, mass and energy balances were performed. Equilibrium constants and advance degrees were calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree (according to Castellan 1986, Fundamentos da Fisica/Quimica, Editora LTC, Rio de Janeiro, p. 529, in Portuguese) is a coefficient that indicates the evolution of a reaction, achieving a maximum value when all the reactants' content is used of reforming increases when the operation temperature also increases and when the operation pressure decreases. However, at atmospheric pressure (1 atm), the advance degree tends to stabilize in temperatures above 700 degrees C; that is, the volume of supplemental production of reforming products is very small with respect to high use of energy resources necessary. The use of unused ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at the same tension, is higher at 700 degrees C than other studied temperatures such as 600 and 650 degrees C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8% and 58.9% in temperatures between 600 and 700 degrees C. The higher calculated current density is 280 mA/cm(2). The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced powers at 190 mA/cm(2) are 99.8, 109.8, and 113.7 mW/cm(2) for 873, 923, and 973 K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describe a process of internal steam reforming of ethanol.

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as MCFC (molten carbonate fuel cell) operate at high temperatures, and due to this issue, cogeneration processes may be performed, sending heat for own process or other purposes as steam generation in an industry. The use of ethanol for this purpose is one of the best options because this is a renewable and less environmentally offensive fuel, and cheaper than oil-derived hydrocarbons (in the case of Brazil). In the same country, because of technical, environmental and economic advantages, the use of ethanol by steam reforming process have been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where are produced the highest volumes of products, making possible a higher production of energy, that is, a most-efficient use of resources. To attain this objective, mass and energy balances are performed. Equilibrium constants and advance degrees are calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree of reforming increases when the operation temperature also increases and when the operation pressure decreases. But at atmospheric pressure (1 atm), the advance degree tends to the stability in temperatures above 700°C, that is, the volume of supplemental production of reforming products is very small for the high use of energy resources necessary. Reactants and products of the steam-reforming of ethanol that weren't used may be used for the reforming. The use of non-used ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at same tension, is higher at 700°C than other studied temperatures as 600 and 650°C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8 and 58.9% in temperatures between 600 and 700°C. The higher calculated current density is 280 mA/cm 2. The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced power at 190 mW/cm 2 is 99.8, 109.8 and 113.7 mW/cm2 for 873, 923 and 973K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describes a process of internal steam reforming of ethanol.