Metallomics and chemical speciation: towards a better understanding of metal-induced stress in plants

Most metal ions are toxic to plants, even at low concentrations, despite the fact that some are essential for growth and play key roles in metabolism. The majority of metals induce the formation of reactive oxygen species, which require the synthesis of additional antoxidant compounds and enzymes for their removal. New techniques that have greatly improved the identification, localisation and quantification of metals within plant tissues have led to the science of metallomics. This advancement in knowledge should eventually allow the characterisation of plants used in the process of phytoremediation of soils contaminated with toxic metals.

Process development for a recombinant Chinese Hamster Ovary (CHO) cell line utilizing a metal induced and amplified metallothionein expression system

The suspension Chinese Hamster Ovary cell line, 13-10-302, utilizing the metallothionein (MT) expression system producing recombinant human growth hormone (hGH) was studied in a serum-free and cadmium-free medium at different fermentation scales and modes of operation. Initial experiments were carried out to optimize the concentration of metal addition to induce the MT promoter. Subsequently, the cultivation of the 13-10-302 cell line was scaled up from spinner flasks into bioreactors, and the cultivation duration was extended with fed-batch and perfusion strategies utilizing 180 muM zinc to induce the promoter controlling expression of recombinant hGH. It was shown that a fed-batch process could increase the maximum cell numbers twofold, from 3.3 to 6.3 x 10(6) cell/mL, over those obtained in normal batch fermentations, and this coupled with extended fermentation times resulted in a fourfold increase in final hGH titer, from 135 +/- 15 to 670 +/- 70 mg/L at a specific productivity q(hGH) value of 12 pg cell(-1)d(-1). The addition of sodium butyrate increased the specific productivity of hGH in cells to a value of approximately 48 pg cell(-1)d(-1), resulting in a final hGH titer of over a gram per liter during fed-batch runs. A BioSep acoustic cell recycler was used to retain the cells in the bioreactor during perfusion operation. It was necessary to maintain the specific feeding rates (SFR) above a value of 0.2 vvd/(10(6) cell/mL) to maintain the viability and productivity of the 13-10-302 cells; under these conditions the viable cell number increased to over 107 cell/mL and resulted in a volumetric productivity of over 120 mg(hGH) L(-1)d(-1). Process development described in this work demonstrates cultivation at various scales and sustained high levels of productivity under cadmium free condition in a CHO cell line utilizing an inducible metallothionein expression system. (C) 2004 Wiley Periodicals, Inc.

A Metal-Repressed Promoter From Gram-Positive Bacillus subtilis Is Highly Active and Metal-Induced in Gram-Negative Cupriavidus metallidurans

A synthetic version of the metal-regulated gene A (mrgA) promoter from Bacillus subtilis, which in this Gram-positive bacterium is negatively regulated by manganese, iron, cobalt, or copper turned out to promote high level of basal gene expression that is further enhanced by Co(II), Cd(II), Mn(II), Zn(II), Cu(II), or Ni(II), when cloned in the Gram-negative bacterium Cupriavidus metallidurans. Promoter activity was monitored by expression of the reporter gene coding for the enhanced green fluorescent protein (EGFP), and cellular intensity fluorescence was quantified by flow cytometry. Expression levels in C. metallidurans driven by the heterologous promoter, here called pan, ranged from 20- to 53-fold the expression level driven by the Escherichia coli lac promoter (which is constitutively expressed in C. metallidurans), whether in the absence or presence of metal ions, respectively. The pan promoter did also function in E. coli in a constitutive pattern, regardless of the presence of Mn(II) or Fe(II). In conclusion, the pan promoter proved to be a powerful tool to express heterologous proteins in Gram-negative bacteria, especially in C. metallidurans grown upon high levels of toxic metals, with potential applications in bioremediation. Biotechnol. Bioeng. 2010; 107: 469-477. (C) 2010 Wiley Periodicals, Inc.

Effects of metal-induced oxidative stress on endothelial cells in vitro

Aseptic loosening of metal implants is mainly attributed to the formation of metal degradation products. These include particulate debris and corrosion products, such as metal ions (anodic half-reaction) and ROS (cathodic half-reaction). While numerous clinical studies describe various adverse effects of metal degradation products, detailed knowledge of metal-induced cellular reactions, which might be important for possible therapeutic intervention, is not comprehensive. Since endothelial cells are involved in inflammation and angiogenesis, two processes which are critical for wound healing and integration of metal implants, the effects of different metal alloys and their degradation products on these cells were investigated. Endothelial cells on Ti6Al4V alloy showed signs of oxidative stress, which was similar to the response of endothelial cells to cathodic partial reaction of corrosion induced directly on Ti6Al4V surfaces. Furthermore, oxidative stress on Ti6Al4V alloy reduced the pro-inflammatory stimulation of endothelial cells by TNF-α and LPS. Oxidative stress and other stress-related responses were observed in endothelial cells in contact with Co28Cr6Mo alloy. Importantly, these features could be reduced by coating Co28Cr6Mo with a TiO2 layer, thus favouring the use of such surface modification in the development of medical devices for orthopaedic surgery. The reaction of endothelial cells to Co28Cr6Mo alloy was partially similar to the effects exerted by Co2+, which is known to be released from metal implants. Co2+ also induced ROS formation and DNA damage in endothelial cells. This correlated with p53 and p21 up-regulation, indicating the possibility of cell cycle arrest. Since CoCl2 is used as an hypoxia-mimicking agent, HIF-1α-dependence of cellular responses to Co2+ was studied in comparison to anoxia-induced effects. Although important HIF-1α-dependent genes were identified, a more detailed analysis of microarray data will be required to provide additional information about the mechanisms of Co2+ action. All these reactions of endothelial cells to metal degradation products might play their role in the complex processes taking place in the body following metal device implantation. In the worst case this can lead to aseptic loosening of the implant and requirement for revision surgery. Knowledge of molecular mechanisms of metal-induced responses will hopefully provide the possibility to interfere with undesirable processes at the implant/tissue interface, thus extending the life-time of the implant and the overall success of metal implant applications.

Crystal structures of the copper and nickel complexes of RNase A: Metal-induced interprotein interactions and identification of a novel copper binding motif

We report the crystal structures of the copper and nickel complexes of RNase A. The overall topology of these two complexes is similar to that of other RNase A structures. However, there are significant differences in the mode of binding of copper and nickel. There are two copper ions per molecule of the protein, but there is only one nickel ion per molecule of the protein. Significant changes occur in the interprotein interactions as a result of differences in the coordinating groups at the common binding site around His-105. Consequently, the copper- and nickel-ion-bound dimers of RNase A act as nucleation sites for generating different crystal lattices for the two complexes. A second copper ion is present at an active site residue His-119 for which all the ligands are from one molecule of the protein. At this second site, His-119 adopts an inactive conformation (B) induced by the copper. We have identified a novel copper binding motif involving the α-amino group and the N-terminal residues.

Hypothesis: is Alzheimer's disease a metal-induced immune disorder?

A hypothesis that a metal-induced immune disorder may be involved in the pathogenesis of some forms of Alzheimer's disease (AD) is presented. The classical complement pathway is activated in AD and T cells and reactive microglia appear in the brain. Studies of metal induced autoimmunity and the use of compounds containing aluminium as vaccine adjuvants suggest that metals can activate complement and can be taken up by antigen presenting cells. The consequent immune response could contribute to neuronal damage, beta-amyloid deposition and cell death. The strengths and weaknesses of this hypothesis are discussed and tests of some aspects are proposed.

Chemisorption of group-III metals on the Si(111) and Ge(111) surfaces: An ab initio study

Chemisorption of group-III metal adatoms on Si(111) and Ge(111) has been studied through the ab initio Hartree-Fock method including nonempirical pseudopotentials and using cluster models to simulate the surface. Three different high-symmetry sites (atop, eclipsed, and open) have been considered by using X4H9, X4H7, and X6H9 (X=Si,Ge) cluster models. In a first step, ideal surface geometries have been used. Metal-induced reconstruction upon chemisorption has also been taken into account. Equilibrium distances, binding energies, and vibrational frequencies have been obtained and compared with available experimental data. From binding-energy considerations, the atop and eclipsed sites seem to be the most favorable ones and thus a coadsorption picture may be suggested. Group-III metals exhibit a similar behavior and the same is true for Si(111) and Ge(111) surfaces when chemisorption is considered.

Metal accumulation and oxidative stress biomarkers in octopus (Octopus vulgaris) from Northwest Atlantic

Metals are ubiquitous in the environment and accumulate in aquatic organisms and are known for their ability to enhance the production of reactive oxygen species (ROS). In aquatic species, oxidative stress mechanisms have been studied by measuring antioxidant enzyme activities and oxidative damages in tissues. The aim of this study was to apply and validate a set of oxidative stress biomarkers and correlate responses with metal contents in tissues of common octopus (Octopus vulgaris). Antioxidant enzyme activity (catalase — CAT, superoxide dismutase — SOD and glutathione S-transferases — GST), oxidative damages (lipid peroxidation — LPO and protein carbonyl content — PCO) andmetal content (Cu, Zn, Pb, Cd and As) in the digestive gland and armof octopus, collected in the NWPortuguese coast in different periods, were assessed after capture and after 14 days in captivity. CAT and SOD activitieswere highly responsive to fluctuations inmetal concentrations and able to reduce oxidative damage, LPO and PCO in the digestive gland. CAT activity was also positively correlated with SOD and GST activities, which emphasizes that the three enzymes respond in a coordinated way to metal induced oxidative stress. Our results validate the use of oxidative stress biomarkers to assess metal pollution effects in this ecological and commercial relevant species.Moreover, octopus seems to have the ability to control oxidative damage by triggering an antioxidant enzyme coordinated response in the digestive gland.

Studies of Eu- and Yb-induced Reconstructions on the Si(100) Surface

This thesis presents experimental studies of rare earth (RE) metal induced structures on Si(100) surfaces. Two divalent RE metal adsorbates, Eu and Yb, are investigated on nominally flat Si(100) and on vicinal, stepped Si(100) substrates. Several experimental methods have been applied, including scanning tunneling microscopy/spectroscopy (STM/STS), low energy electron diffraction (LEED), synchrotron radiation photoelectron spectroscopy (SR-PES), Auger electron spectroscopy (AES), thermal desorption spectroscopy (TDS), and work function change measurements (Δφ). Two stages can be distinguished in the initial growth of the RE/Si interface: the formation of a two-dimensional (2D) adsorbed layer at submonolayer coverage and the growth of a three-dimensional (3D) silicide phase at higher coverage. The 2D phase is studied for both adsorbates in order to discover whether they produce common reconstructions or reconstructions common to the other RE metals. For studies of the 3D phase Yb is chosen due to its ability to crystallize in a hexagonal AlB2 type lattice, which is the structure of RE silicide nanowires, therefore allowing for the possibility of the growth of one-dimensional (1D) wires. It is found that despite their similar electronic configuration, Eu and Yb do not form similar 2D reconstructions on Si(100). Instead, a wealth of 2D structures is observed and atomic models are proposed for the 2×3-type reconstructions. In addition, adsorbate induced modifications on surface morphology and orientational symmetry are observed. The formation of the Yb silicide phase follows the Stranski-Krastanov growth mode. Nanowires with the hexagonal lattice are observed on the flat Si(100) substrate, and moreover, an unexpectedly large variety of growth directions are revealed. On the vicinal substrate the growth of the silicide phase as 3D islands and wires depends drastically on the growth conditions. The conditions under which wires with high aspect ratio and single orientation parallel to the step edges can be formed are demonstrated.

Reconstruction and electrochemical oxidation of Au(110) surface in 0.1 M H2SO4

Variations of the surface structure and composition of the Au(110) electrode during the formation/lifting of the surface reconstruction and during the surface oxidation/reduction in 0.1 M aqueous sulfuric acid were studied by cyclic voltammetry, scanning tunneling microscopy and shell-isolated nanoparticle enhanced Raman spectroscopy. Annealing of the Au(110) electrode leads to a thermally-induced reconstruction formed by intermixed (1×3) and (1×2) phases. In a 0.1 M H2SO4 solution, the decrease of the potential of the atomically smooth Au(110)-(1×1) surface leads to the formation of a range of structures with increasing surface corrugation. The electrochemical oxidation of the Au(110) surface starts by the formation of anisotropic atomic rows of gold oxide. At higher potentials we observed a disordered structure of the surface gold oxide, similar to the one found for the Au(111) surface.

Water circulations for effective bleaching of high-brightness mechanical pulps

The amount of water available is usually restricted, which leads to a situation where a complete understanding of the process, including water circulations and the influence of water components, is essential. The main aim of this thesis was to clarify the possibilities for the efficient use of residual peroxide by means of water circulation rearrangements. Rearranging water circulations and the reduction of water usage may cause new problems, such as metal induced peroxide decomposition that needs to be addressed. This thesis introduces theoretical methods of water circulations to combine two variables; effective utilization of residual peroxide and avoiding manganese in the alkaline peroxide bleaching stage. Results are mainly based on laboratory and mill site experiments concerning the utilization of residual peroxide. A simulation model (BALAS) was used to evaluate the manganese contents and residual peroxide doses. It was shown that with optimum recirculation of residual peroxide the brightness can be improved or chemical costs can be decreased. From the scientific perspective, it was also very important to discover that recycled peroxide was more effective pre-bleaching agent compared to fresh peroxide. This can be due to the organic acids i.e. per acetic acid in wash press filtrate that have been formed in alkaline bleaching stage. Even short retention time was adequate and the activation of residual peroxide using sodium hydroxide was not necessary. There are several possibilities for using residual peroxide in practice regarding bleaching. A typical modern mechanical pulping process line consist of defibering, screening, a disc filter, a bleach press, high consistency (HC) peroxide bleaching and a wash press. Furthermore there usually is not a particular medium consistency (MC) pre-bleaching stage that includes additional thickening equipment. The most advisable way to utilize residual peroxide in this kind of process is to recycle the wash press filtrate to the dilution of disc filter pulp (low MC pre-bleaching stage). An arrangement such as this would be beneficial in terms of the reduced convection of manganese to the alkaline bleaching stage. Manganese originates from wood material and will be removed to the water phase already in the early stages of the process. Recycling residual peroxide prior to the disc filter is not recommended because of low consistencies. Regarding water circulations, the novel point of view is that, it would be beneficial to divide water circulations into two sections and the critical location for the division is the disc filter. Both of these two sections have their own priority. Section one before the disc filter: manganese removal. Section two after the disc filter: brightening of pulp. This division can be carried out if the disc filter pulp is diluted only by wash press filtrate before the MC storage tower. The situation is even better if there is an additional press after the disc filter, which will improve the consistency of the pulp. This has a significant effect on the peroxide concentration in the MC pre-bleaching stage. In terms of manganese content, it is essential to avoid the use of disc filter filtrate in the bleach press and wash press showers. An additional cut-off press would also be beneficial for manganese removal. As a combination of higher initial brightness and lower manganese content, the typical brightness increase varies between approximately 0.5 and 1% ISO units after the alkaline peroxide bleaching stage. This improvement does not seem to be remarkable, but as it is generally known, the final brightness unit is the most expensive and difficult to achieve. The estimation of cost savings is not unambiguous. For example in GW/TMP mill case 0.6% ISO units higher final brightness gave 10% savings in the costs of bleaching chemicals. With an hypothetical 200 000 ton annual production, this means that the mill could save in the costs of bleaching chemicals more than 400 000 euros per year. In general, it can be said that there were no differences between the behavior of different types of processes (GW, PGW, TMP and BCTMP). The enhancement of recycling gave a similar response in all cases. However, we have to remember that the utilization of residual peroxide in older mills depends a great deal on the process equipment, the amount of water available and existing pipeline connections. In summary, it can be said that processes are individual and the same solutions cannot be applied to all cases.

Zur Synthese von alpha-Aminoaldehyden und Aminosäuren mit alpha-quartären Zentren durch Aziridinierung funktionalisierter Olefine

Ziel dieser Arbeit war, durch Aziridinierung homochiraler 5-Methyl-4H-1,3-dioxinen eine neue Methode zur Synthese von alpha-Aminoaldehyden und den ableitbaren Aminosäuren mit alpha-quartären Zentren zu entwickeln. Die chiralen 5-Methyl-4H-1,3-dioxine sind mit hohen Enantiomerenüberschüssen durch asymmetrische Doppelbindungsisomerisierung von 5-Methylen-1,3-dioxanen zugänglich. Die Metall-katalysierte Aziridinierung der 5-Methyl-4H-1,3-dioxine mit der Nitrenquelle (N-Tosylimino)phenyliodinan führte direkt zu N-Tosyl-geschützen 4-Methyl-1,3-oxazolidin-4-carbaldehyden. Vermutlich über ein Aziridin als nicht isolierbare Zwischenstufe werden über eine Ringöffnungs-/Ringverengungsreaktion die Oxazolidinderivate gebildet, vorzugsweise in Gegenwart von Cu(I)-Katalysatoren, während die Rhodium-katalysierte Reaktion ausschließlich zu Insertionsprodukten führt. In der Cu-katalysierten Aziridinierung ist das Verhältnis von Aziridinierung/Insertion abhängig von der Katalysatorkonzentration. Die Aziridinierung mit N-(p-Nitrobenzolsulfonyl)- und N-(Trimethylsilylethylsulfonyl)- substituierten Nitrenquellen führt zu Oxazolidinderivaten mit leichter abspaltbaren Schutzgruppen. Diese Nitrenquellen können in situ aus den korrespondierenden Sulfonamiden mit Iodosobenzol dargestellt werden. Bei dem Einsatz homochiraler 4H-1,3-Dioxine ist Erhalt der Stereoinformation abhängig vom Substituenten in 2-Position der Dioxine sowie von der Polarität des Lösungsmittels. Die höchsten Selektivitäten wurden in tert-Butylmethylether erzielt. In Falle des 2-tert-Butyl-4-methyl-3-(toluol-4-sulfonyl)-1,3-oxazolidin-4-carbaldehyds kristallisiert das Hauptdiastereomer in enantiomerenreiner Form. Die Absolutkonfiguration wurde durch Röntgenkristallstrukturanalyse ermittelt. Das Anwendungspotential dieser neuen Methode konnte durch Überführen der Serinale in Aminoalkohole und alpha-Methylserin-Derivate sowie in der Synthese der unnatürlichen Aminosäure alpha-Vinylalanin gezeigt werden.

Zur Herstellung von chiralen α-Aminosäuren mit α-quartären Zentren und deren Verwendung als Synthone in der organischen Synthese

Ziel dieser Arbeit war, ausgehend von alpha-Aminoaldehyden eine kurze und effiziente Synthese zur Darstellung von Aminosäuren mit alpha-quartären Zentren in enantiomerenreiner Form und davon ableitbare wichtige Synthone in der organischen Synthese zu entwickeln. Der enantiomerenreine 2-tert-Butyl-4-methyl-1,3-oxazolidin-4-carbaldehyd ist via kupfer-katalysierter Aziridinierung des enantiomerenangereicherten 2-tert-Butyl-5-methyl-4H-1,3-dioxins mit der Nitrenquelle (N-Tosylimino)phenyliodinan zugänglich. Eine anschließende Oxidation mit Natriumhyperchlorid und Wasserstoffperoxid führt zur korrespondierenden Carbonsäure, die via sauer katalysierter Acetalspaltung und nachfolgender Abspaltung der Tosyl-Schutzgruppe in enantiomerenreines alpha-Methylserin in sehr guten Ausbeuten umgewandelt werden kann. Mit dem Einsatz von in C5-Position Ethyl-substituiertem 2-tert-Butyl-4H-1,3-dioxin ist analog das N-Tosyl geschützte alpha-Ethylserin darstellbar. Um die bestehende Lösungsmittelabhängigkeit in weniger polaren Losungsmitteln wie Dichlormethan oder Diethylether der Aziridinierung in Bezug auf ihre Diastereoselektivität und Reaktivität zu minimieren, wurden unterschiedliche Nitrenquellen untersucht. [N-(p-Methoxybenzolsulfonyl)imino]methoxyphenyliodinan stellte sich als die potenteste Nitrenquelle heraus und die Ausbeute konnte auf bis zu 70% gesteigert werden. Die Anwendbarkeit des N-Tosyl geschützten alpha-Methylserins konnte mit der Synthese des β-Lactons und 2-Carboxylethylether-2-aziridin unter Mitsunobu-Bedingungen gezeigt werden. Dabei ist die Reaktion durch einfache Variation des Lösungsmittels und der Reaktionstemperatur zu beiden Produkten in sehr guten Ausbeuten hin steuerbar. Das β-Lacton konnte anschließend erfolgreich in das N-Tosyl- und S-Acetyl- geschützte alpha-Methylcystein überführt werden.