Propuesta didáctica el uso de experimentos demostrativos y la contextualización de conceptos como una ayuda a la construcción del conocimiento en los temas de mecánica de fluídos y calor [por] José Antonio Matta Garza

Tesis (Maestría en la Enseñanza de las Ciencias con Especialidad en Física) U.A.N.L.

Física I : mecánica y fluídos.

Este manual está dividido en 13 temas: 1.La magnitud física y su medida, 2.Cálculo vectorial, 3.Cinemática del punto, 4.Cinemática del sólido rígido y del movimiento relativo, 5.Estática: fuerzas y equilibrios, 6.Dinámica del punto y de los sistemas de puntos, 7.Trabajo y energía, 8.Dinámica de rotación del sólido rígido, 9.Gravitación, 10.El estado sólido y la elasticidad, 11.Estática de fluídos, 12.Fenómenos capilares en los líquidos y 13.Dinámica de fluídos.

Estudio paramétrico del conjunto tractor-trailer mediante aplicación de mecánica de fluidos computacional

La mejora del comportamiento aerodinámico de vehículos pesados en la carretera ha adquirido una mayor importancia estos últimos años debido a la crisis y su consecuente aumento del precio de los combustibles. Dado que una reducción en la resistencia aerodinámica del vehículo conlleva un menor empleo de combustible, el objetivo de este proyecto es realizar un estudio paramétrico del conjunto tractor-tráiler mediante la mecánica de fluidos computacional (CFD) para así obtener la geometría que proporciona un menor gasto de combustible cuando ésta es expuesta a viento frontal. La influencia de 3 parámetros, que son la separación existente entre cabina y remolque, la altura del remolque y el radio de curvatura de las aristas frontales de la cabina, es analizada en este estudio dividido en varias etapas que implican el uso de programas específicos como son: la parametrización y creación de las geometrías en 3D que es llevada a cabo mediante CATIA, el mallado del dominio (realizado con Gambit) y resolución de las ecuaciones mediante FLUENT. Finalmente se obtendrá una relación entre la resistencia aerodinámica (representada mediante el coeficiente de arrastre) y la combinación de los 3 parámetros, que nos permitirá decidir que geometría es la óptima. Abstract The improvement of the heavy vehicle’s aerodynamic behavior on the road has gained a great importance for these last years because of the economic crisis and the consequent increase of the price of the fuels. Due to the fact that a reduction in the aerodynamic resistance of the vehicle involves using a smaller amount of fuel, the objective of this project is to carry out a parametric study about the ensemble tractor-trailer by computational fluid dynamics methods (CFD) in order to obtain the geometry which expense of fuel is the lowest when it’s exposed to frontal wind. The influence of the three parameters, which are the space between cab and trailer, the height of the trailer and the curvature of the frontal cab edges, is analysed in this study which is divided into different parts involving specific programs: choosing the parameters and building the geometries, which is done by using CATIA, the mesh is built by Gambit, and the program equations-solver is FLUENT. Finally a ratio between aerodynamic resistance and a combination of the three parameters will be obtained and it will allow us to choose the best geometry.

Optimización de la agitación de un digestor anaerobio mediante mecánica de fluidos computacional

Debido al gran interés existente en el ahorro y recuperación de energía, y en el deseo de obtener productos que permitan usos beneficiosos del fango procedente de la depuración del agua residual, la digestión anaerobia es el proceso de estabilización de uso más extendido. El tiempo de retención de sólidos es un factor clave en el proceso de digestión anaerobia. En base al tiempo de retención de sólidos, se dimensiona el volumen de los digestores anaerobios para así obtener la reducción de materia orgánica deseada, con la correspondiente producción de biogás. La geometría del digestor y su sistema de agitación deben ser adecuados para alcanzar el tiempo de retención de sólidos de diseño. Los primeros trabajos sobre la agitación de los digestores realizaban únicamente experimentos con trazadores y otros métodos de medición. En otros casos, la mezcla era evaluada mediante la producción de biogás. Estas técnicas tenían el gran hándicap de no conocer lo que sucedía realmente dentro del digestor y sólo daban una idea aproximada de su funcionamiento. Mediante aplicación de la mecánica de fluidos computacional (CFD) es posible conocer con detalle las características del fluido objeto de estudio y, por lo tanto, simular perfectamente el movimiento del fango de un digestor anaerobio. En esta tesis se han simulado mediante CFD diferentes digestores a escala real (unos 2000 m3 de volumen) agitados con bomba/s de recirculación para alcanzar los siguientes objetivos: establecer la influencia de la relación entre el diámetro y la altura, de la pendiente de la solera, del número de bombas y del caudal de recirculación en dichos digestores, definir el campo de velocidades en la masa de fango y realizar un análisis energético y económico. Así, es posible conocer mejor cómo funciona el sistema de agitación de un digestor anaerobio a escala real equipado con bomba/s de recirculación. Los resultados obtenidos muestran que una relación diámetro/altura del digestor por encima de 1 empeora la agitación del mismo y que la pendiente en la solera del digestor favorece que la masa de fango esté mejor mezclada, siendo más determinante la esbeltez del tanque que la pendiente de su solera. No obstante, también es necesario elegir adecuadamente los parámetros de diseño del sistema de agitación, en este caso el caudal de recirculación de fango, para obtener una agitación completa sin apenas zonas muertas. En el caso de un digestor con una geometría inadecuada es posible mejorar su agitación aumentando el número de bombas de recirculación y el caudal de las mismas, pero no se llegará a alcanzar una agitación total de la masa de fango debido a su mal diseño original. Anaerobic digestion is the process for waste water treatment sludge stabilization of more widespread use due to the huge interest in saving and recovering energy and the wish to obtain products that allow beneficial uses for the sludge. The solids retention time is a key factor in the anaerobic digestion. Based on the solids retention time, volume anaerobic digester is sized to obtain the desired reduction in organic matter, with the corresponding production of biogas. The geometry of the digester and the stirring system should be adequate to achieve the design solid retention time. Early works on digesters stirring just performed tracer experiments and other measurement methods. In other cases, mixing was evaluated by biogas production. These techniques had the great handicap of not knowing what really happened inside the digester and they only gave a rough idea of its operation. By application of computational fluid dynamics (CFD), it is possible to know in detail the characteristics of the fluid under study and, therefore, simulate perfectly the sludge movement of an anaerobic digester. Different full-scale digesters (about 2000 m3 of volume) agitated with pump/s recirculation have been simulated by CFD in this thesis to achieve the following objectives: to establish the influence of the relationship between the diameter and height, the slope of the bottom, the number of pumps and the recirculation flow in such digesters, to define the velocity field in the mass of sludge and carry out an energy and economic analysis. Thus, it is possible to understand better how the agitation system of a full-scale anaerobic digester equipped with pump/s recirculation works. The results achieved show that a diameter/height ratio of the digester above 1 worsens its stirring and that the slope of the digester bottom favors that the mass of sludge is better mixed, being more decisive the tank slenderness than the slope of its bottom. However, it is also necessary to select properly the design parameters of the agitation system, in this case the sludge recirculation flow rate, for a complete agitation with little dead zones. In the case of a digester with inadequate geometry, its agitation can be improved by increasing the number of recirculation pumps and flow of them, but it will not reach a full agitation of the mass of sludge because of the poor original design.

On the zeros of polynomials: an extension of the Enestrom-Kakeya theorem

This paper presents an extension of the Enestrom-Kakeya theorem concerning the roots of a polynomial that arises from the analysis of the stability of Brown (K, L) methods. The generalization relates to relaxing one of the inequalities on the coefficients of the polynomial. Two results concerning the zeros of polynomials will be proved, one of them providing a partial answer to a conjecture by Meneguette (1994)[6]. (C) 2011 Elsevier Inc. All rights reserved.

Application of the log-conformation tensor to three-dimensional time-dependent free surface flows

The numerical simulation of flows of highly elastic fluids has been the subject of intense research over the past decades with important industrial applications. Therefore, many efforts have been made to improve the convergence capabilities of the numerical methods employed to simulate viscoelastic fluid flows. An important contribution for the solution of the High-Weissenberg Number Problem has been presented by Fattal and Kupferman [J. Non-Newton. Fluid. Mech. 123 (2004) 281-285] who developed the matrix-logarithm of the conformation tensor technique, henceforth called log-conformation tensor. Its advantage is a better approximation of the large growth of the stress tensor that occur in some regions of the flow and it is doubly beneficial in that it ensures physically correct stress fields, allowing converged computations at high Weissenberg number flows. In this work we investigate the application of the log-conformation tensor to three-dimensional unsteady free surface flows. The log-conformation tensor formulation was applied to solve the Upper-Convected Maxwell (UCM) constitutive equation while the momentum equation was solved using a finite difference Marker-and-Cell type method. The resulting developed code is validated by comparing the log-conformation results with the analytic solution for fully developed pipe flows. To illustrate the stability of the log-conformation tensor approach in solving three-dimensional free surface flows, results from the simulation of the extrudate swell and jet buckling phenomena of UCM fluids at high Weissenberg numbers are presented. (C) 2012 Elsevier B.V. All rights reserved.

A marker-and-cell approach to free surface 2-D multiphase flows

This work describes a methodology to simulate free surface incompressible multiphase flows. This novel methodology allows the simulation of multiphase flows with an arbitrary number of phases, each of them having different densities and viscosities. Surface and interfacial tension effects are also included. The numerical technique is based on the GENSMAC front-tracking method. The velocity field is computed using a finite-difference discretization of a modification of the NavierStokes equations. These equations together with the continuity equation are solved for the two-dimensional multiphase flows, with different densities and viscosities in the different phases. The governing equations are solved on a regular Eulerian grid, and a Lagrangian mesh is employed to track free surfaces and interfaces. The method is validated by comparing numerical with analytic results for a number of simple problems; it was also employed to simulate complex problems for which no analytic solutions are available. The method presented in this paper has been shown to be robust and computationally efficient. Copyright (c) 2012 John Wiley & Sons, Ltd.

Simulation results and applications of an advection bounded scheme to practical flows

This paper reports experiments on the use of a recently introduced advection bounded upwinding scheme, namely TOPUS (Computers & Fluids 57 (2012) 208-224), for flows of practical interest. The numerical results are compared against analytical, numerical and experimental data and show good agreement with them. It is concluded that the TOPUS scheme is a competent, powerful and generic scheme for complex flow phenomena.

A continuously differentiable upwinding scheme for the simulation of fluid flow problems

This paper deals with the numerical solution of complex fluid dynamics problems using a new bounded high resolution upwind scheme (called SDPUS-C1 henceforth), for convection term discretization. The scheme is based on TVD and CBC stability criteria and is implemented in the context of the finite volume/difference methodologies, either into the CLAWPACK software package for compressible flows or in the Freeflow simulation system for incompressible viscous flows. The performance of the proposed upwind non-oscillatory scheme is demonstrated by solving two-dimensional compressible flow problems, such as shock wave propagation and two-dimensional/axisymmetric incompressible moving free surface flows. The numerical results demonstrate that this new cell-interface reconstruction technique works very well in several practical applications. (C) 2012 Elsevier Inc. All rights reserved.

Interpolation estimate for a finite-element space with embedded discontinuities

We consider a recently proposed finite-element space that consists of piecewise affine functions with discontinuities across a smooth given interface Γ (a curve in two dimensions, a surface in three dimensions). Contrary to existing extended finite element methodologies, the space is a variant of the standard conforming Formula space that can be implemented element by element. Further, it neither introduces new unknowns nor deteriorates the sparsity structure. It is proved that, for u arbitrary in Formula, the interpolant Formula defined by this new space satisfies Graphic where h is the mesh size, Formula is the domain, Formula, Formula, Formula and standard notation has been adopted for the function spaces. This result proves the good approximation properties of the finite-element space as compared to any space consisting of functions that are continuous across Γ, which would yield an error in the Formula-norm of order Graphic. These properties make this space especially attractive for approximating the pressure in problems with surface tension or other immersed interfaces that lead to discontinuities in the pressure field. Furthermore, the result still holds for interfaces that end within the domain, as happens for example in cracked domains.

Numerical assessment of stability of interface discontinuous finite element pressure spaces

The stability of two recently developed pressure spaces has been assessed numerically: The space proposed by Ausas et al. [R.F. Ausas, F.S. Sousa, G.C. Buscaglia, An improved finite element space for discontinuous pressures, Comput. Methods Appl. Mech. Engrg. 199 (2010) 1019-1031], which is capable of representing discontinuous pressures, and the space proposed by Coppola-Owen and Codina [A.H. Coppola-Owen, R. Codina, Improving Eulerian two-phase flow finite element approximation with discontinuous gradient pressure shape functions, Int. J. Numer. Methods Fluids, 49 (2005) 1287-1304], which can represent discontinuities in pressure gradients. We assess the stability of these spaces by numerically computing the inf-sup constants of several meshes. The inf-sup constant results as the solution of a generalized eigenvalue problems. Both spaces are in this way confirmed to be stable in their original form. An application of the same numerical assessment tool to the stabilized equal-order P-1/P-1 formulation is then reported. An interesting finding is that the stabilization coefficient can be safely set to zero in an arbitrary band of elements without compromising the formulation's stability. An analogous result is also reported for the mini-element P-1(+)/P-1 when the velocity bubbles are removed in an arbitrary band of elements. (C) 2012 Elsevier B.V. All rights reserved.

A new enrichment space for the treatment of discontinuous pressures in multi-fluid flows

In this work, a new enrichment space to accommodate jumps in the pressure field at immersed interfaces in finite element formulations, is proposed. The new enrichment adds two degrees of freedom per element that can be eliminated by means of static condensation. The new space is tested and compared with the classical P1 space and to the space proposed by Ausas et al (Comp. Meth. Appl. Mech. Eng., Vol. 199, 10191031, 2010) in several problems involving jumps in the viscosity and/or the presence of singular forces at interfaces not conforming with the element edges. The combination of this enrichment space with another enrichment that accommodates discontinuities in the pressure gradient has also been explored, exhibiting excellent results in problems involving jumps in the density or the volume forces. Copyright (c) 2011 John Wiley & Sons, Ltd.

Finite element methods for the Stokes system based on a Zienkiewicz type N-simplex

Hermite interpolation is increasingly showing to be a powerful numerical solution tool, as applied to different kinds of second order boundary value problems. In this work we present two Hermite finite element methods to solve viscous incompressible flows problems, in both two- and three-dimension space. In the two-dimensional case we use the Zienkiewicz triangle to represent the velocity field, and in the three-dimensional case an extension of this element to tetrahedra, still called a Zienkiewicz element. Taking as a model the Stokes system, the pressure is approximated with continuous functions, either piecewise linear or piecewise quadratic, according to the version of the Zienkiewicz element in use, that is, with either incomplete or complete cubics. The methods employ both the standard Galerkin or the Petrov–Galerkin formulation first proposed in Hughes et al. (1986) [18], based on the addition of a balance of force term. A priori error analyses point to optimal convergence rates for the PG approach, and for the Galerkin formulation too, at least in some particular cases. From the point of view of both accuracy and the global number of degrees of freedom, the new methods are shown to have a favorable cost-benefit ratio, as compared to velocity Lagrange finite elements of the same order, especially if the Galerkin approach is employed.

Mecánica de sólidos y de fluídos. Física I.

El libro está dividido en ocho unidades didácticas, en las cuales se aborda el estudio de los siguientes temas: 1. Conceptos fundamentales, cálculo vectorial y teoría de campos, 2. Cinemática, 3. Dinámica del punto material, 4. Geometría de masas, 5. Estática, 6. Dinámica del sólido rígido, 7. Mecánica del sólido reformable y 8. Mecánica de fluídos.

Laboratorio de mecánica de fluidos

UANL