A Comparison of Deep Drawing and Ironing of Metal Alloy Strip Produced conventionally and Non-conventionally via Semi Solid Material Processing

A semi solid thin strip continuous casting process was used to obtain 50%wt Pb/50%wtSn strip by single and twin roll processing at speed of 15 m/min. A 50%wt Pb/50%wtSn plate ingot was also cast for rolling conventionally into strips of 1.4 mm thickness and 45 mm width for comparison with those achieved non-conventionally. This hypoeutectic alloy has a solidification interval and fusion temperature of approximately 31 degrees C and 215 degrees C respectively. The casting alloy temperature was around 280 degrees C as measured by a type K immersion thermocouple prior to pouring into a tundish designed to maintain a constant melt flow on the cooling slope during semi solid material production. A nozzle with a weir ensures that the semi solid material is dragged smoothly by the lower roll, producing strip with minimum contamination of slag/oxide. The temperatures of the cooling slope and the lower roll were also monitored using K type thermocouples. The coiled semi solid strip, which has a thickness of 1.5 mm and 45 mm width, was rolled conventionally in order to obtain 1.2 mm thick strip. The coiled thixorolled strip had a thickness of 1.2 mm and achieved practically the same width as the conventional strips. Blanks of 40 mm diameter were cut from the strips in a mechanical press, ready for deep drawing and ironing for mechanical characterization. All the strips achieved from non-conventional processing had the same mechanical performance as those achieved conventionally. The limiting drawing ratio (LDR) achieved was approximately 2.0 for all strips. Microscopy examination was made in order to observe phase segregation during processing.

Decentralising natural resource governance in Ghana: critical reflections on the artisanal and small-scale mining sector

This paper critically examines the impact of decentralization on contemporary and future governance arrangements in Ghana’s artisanal and small-scale mining (ASM) sector. The sector, while providing valuable employment in rural areas, is beleaguered by environmental and social issues. Proponents of decentralization argue that re-distributing decision-making authority leads to more responsive, transparent and efficient natural resource management. The analysis presented here, however, demonstrates how weak decentralization has exacerbated the complex, conflictual and clandestine nature of local resource politics surrounding ASM. If future decentralization reforms are going to reverse this trend and improve the governance of ASM in Ghana, then facilitating the participation of traditional authorities is imperative. It is argued that doing so requires addressing the reticence regarding the role of chiefs in resource governance; simply ironing out existing technical issues with decentralization reforms is unlikely to improve the social and environmental performance of ASM in the country. In light of the chronic resource management deficiencies in Ghana, epitomized in the ASM sector, fostering frank political debates on resource governance is becoming urgent.

Influence of surface texture on the galling characteristics of lean duplex and austenitic stainless steels

Two simulative test methods were used to study galling in sheet forming of two types of stainlesssteel sheet: austenitic (EN 1.4301) and lean duplex LDX 2101 (EN 1.4162) in different surface conditions. Thepin-on-disc test was used to analyse the galling resistance of different combinations of sheet materials and lubricants. The strip reduction test, a severe sheet forming tribology test was used to simulate the conditionsduring ironing. This investigation shows that the risk of galling is highly dependent on the surface texture of theduplex steel. Trials were also performed in an industrial tool used for high volume production of pumpcomponents, to compare forming of LDX 2101 and austenitic stainless steel with equal thickness. The forming forces, the geometry and the strains in the sheet material were compared for the same component.It was found that LDX steels can be formed to high strain levels in tools normally applied for forming ofaustenitic steels, but tool adaptations are needed to comply with the higher strength and springback of thematerial.

Optimal auction with a general distribution: virtual valuation without densities

We characterize the optimal auction in an independent private values framework for a completely general distribution of valuations. We do this introducing a new concept: the generalized virtual valuation. To show the wider applicability of this concept we present two examples showing how to extend the classical models of Mussa and Rosen and Baron and Myerson for arbitrary distributions

Fabricação e caracterização metalográfica e mecânica de tiras de ligas metálicas fundidas e tixolaminadas no estado semi-sólido de diferentes intervalos de solidificação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Situation of unpaid work and gender in the Caribbean: The measurement of unpaid work through time-use studies

Includes bibliography.

Perda da eficácia dos materiais hidrorrepelentes na proteção contra agrotóxicos por processos de lavagens

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

U.M. Laundry Dept.

Four captioned images on page entitled Second Floor; Basement. Includes: Ironing Dept.; Collar & Curtain Dept.; Water Softening Equip't; Contagious Wash Room.

Melhoria do sistema produtivo de escadotes da FUTE – Fábrica de Utilidade de Tubos, SA

Atualmente as empresas encontram-se perante uma sociedade cada vez mais competitiva e desenvolvida, sendo por isso, imperativo a procura da melhoria contínua como forma de assegurar a adaptação da organização empresarial às alterações socioeconómicas que possam surgir. Incutir esta cultura é fundamental dentro do meio empresarial. A redução dos custos e o aumento da produtividade são dois dos principais desafios que todas as empresas se confrontam diariamente, sendo para isso desenvolvidas e aplicadas várias metodologias. A presente dissertação foi realizada no âmbito do Mestrado em Engenharia Mecânica no ramo de Gestão Industrial no Instituto Superior de Engenharia do Porto. Este trabalho realizou-se no ambiente industrial da empresa Afer FUTE - Fábrica de Utilidades de Tubos, S.A, que é uma empresa dedicada, essencialmente à produção de Tábuas de Engomar e Escadotes. O objetivo deste projeto visava melhorar todo o sistema produtivo da secção dos Escadotes, englobando assim todos os procedimentos desde o momento de entrada dos materiais até à obtenção do produto acabado. Tendo em vista a resolução dos problemas inicialmente existentes na empresa, foram apresentadas propostas de melhoria do processo produtivo segundo uma visão, Lean Production ou seja baseada na eliminação de qualquer tipo de desperdícios. A implementação destas propostas permitiu a obtenção de resultados positivos no Sistema Produtivo de Escadotes, nomeadamente um aumento de produtividade em cerca de 40%.