A Simple Instrumentation Calibration Technique for Electrical Impedance Tomography (EIT) Using A 16-Electrode Phantom

A simple analog instrumentation for Electrical Impedance Tomography is developed and calibrated using the practical phantoms. A constant current injector consisting of a modified Howland voltage controlled current source fed by a voltage controlled oscillator is developed to inject a constant current to the phantom boundary. An instrumentation amplifier, 50 Hz notch filter and a narrow band pass filter are developed and used for signal conditioning. Practical biological phantoms are developed and the forward problem is studied to calibrate the EIT-instrumentation. An array of sixteen stainless steel electrodes is developed and placed inside the phantom tank filled with KCl solution. 1 mA, 50 kHz sinusoidal current is injected at the phantom boundary using adjacent current injection protocol. The differential potentials developed at the voltage electrodes are measured for sixteen current injections. Differential voltage signal is passed through an instrumentation amplifier and a filtering block and measured by a digital multimeter. A forward solver is developed using Finite Element Method in MATLAB7.0 for solving the EIT governing equation. Differential potentials are numerically calculated using the forward solver with a simulated current and bathing solution conductivity. Measured potential data is compared with the differential potentials calculated for calibrating the instrumentation to acquire the voltage data suitable for better image reconstruction.

A Study of Practical Biological Phantoms with Simple Instrumentation for Electrical Impedance Tomography (EIT)

16-electrode phantoms are developed and studied with a simple instrumentation developed for Electrical Impedance Tomography. An analog instrumentation is developed with a sinusoidal current generator and signal conditioner circuit. Current generator is developed withmodified Howland constant current source fed by a voltage controlled oscillator and the signal conditioner circuit consisting of an instrumentation amplifier and a narrow band pass filter. Electronic hardware is connected to the electrodes through a DIP switch based multiplexer module. Phantoms with different electrode size and position are developed and the EIT forward problem is studied using the forward solver. A low frequency low magnitude sinusoidal current is injected to the surface electrodes surrounding the phantom boundary and the differential potential is measured by a digital multimeter. Comparing measured potential with the simulated data it is intended to reduce the measurement error and an optimum phantom geometry is suggested. Result shows that the common mode electrode reduces the common mode error of the EIT electronics and reduces the error potential in the measured data. Differential potential is reduced up to 67 mV at the voltage electrode pair opposite to the current electrodes. Offset potential is measured and subtracted from the measured data for further correction. It is noticed that the potential data pattern depends on the electrode width and the optimum electrode width is suggested. It is also observed that measured potential becomes acceptable with a 20 mm solution column above and below the electrode array level.

Sensing of Stimulus Artifact Suppressed Signals From Electrode Interfaces

Stimulus artifacts inhibit reliable acquisition of biological evoked potentials for several milliseconds if an electrode contact is utilized for both electrical stimulation and recording purposes. This hinders the measurement of evoked short-latency biological responses, which is otherwise elicited by stimulation in implantable prosthetic devices. We present an improved stimulus artifact suppression scheme using two electrode simultaneous stimulation and differential readout using high-gain amplifiers. Substantial reduction of artifact duration has been shown possible through the common-mode rejection property of an instrumentation amplifier for electrode interfaces. The performance of this method depends on good matching of electrode-electrolyte interface properties of the chosen electrode pair. A novel calibration algorithm has been developed that helps in artificial matching of impedance and thereby achieves the required performance in artifact suppression. Stimulus artifact duration has been reduced down to 50 mu s from the stimulation-cum-recording electrodes, which is similar to 6x improvement over the present state of the art. The system is characterized with emulated resistor-capacitor loads and a variety of in-vitro metal electrodes dipped in saline environment. The proposed method is going to be useful for closed-loop electrical stimulation and recording studies, such as bidirectional neural prosthesis of retina, cochlea, brain, and spinal cord.

Medidas e análise estatística em sinais bioelétricos sobre pontos de acupuntura

In the 20th century, the acupuncture has spread on occident as a complementary practice of heath care. This fact has motivated the international scientific community to invest in research that seek to understand why acupuncture works. In this work we compare statistically volt age fluctuation of bioelectric signals caught on the skin at an acupuncture point (IG 4) another nearby on acupuncture point. The acquisition of these signals was performed utilizing an electronic interface with a computer, which was based on an instrumentation amplifier designed with adequate specifications to this end. On the collected signals from a sample of 30 volunteers we have calculated major statistics and submitted them to pairing t-test with significance leveI a = O, 05. We have estimated to bioelectric signals the following parameters: standard deviation, asymmetry and curtose. Moreover, we have calculated the self-correlation function matched by on exponential curve we have observed that the signal decays more rapidly from a non-acupoint then from an acupoint. This fact is an indicative of the existence of information in the acupoint

Dinamômetro biomédico para avaliação funcional das mãos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aplicativo Android para aquisição de dados de um baropodômetro via Bluetooth para apoio na análise de escoliose

Pós-graduação em Engenharia Elétrica - FEIS

Sistema de adquisición de datos basado en FPAA

Las FPAA´s son dispositivos analógicos programables. Estos dispositivos se basan en el uso de condensadores conmutados junto con amplificadores operacionales. Este tipo de tecnología presenta una serie de ventajas, ya que combinan las ventajas de dispositivos digitales, como la reprogramación en función de las variables del entorno que los rodean, con la diferencia de ser dispositivos analógicos, permitiendo la realización de una amplia gama de diseños analógicos en un solo chip. En este proyecto se ha realizado un estudio sobre el funcionamiento de los condensadores conmutados y su uso en el dispositivo AN221E04 del fabricante Anadigm. Una vez descrita la arquitectura del AN221E04 y explicadas las bases del funcionamiento de los condensadores conmutados, utilizando como ejemplo los modelos facilitados por Anadigm, se desarrolla un modelo de amplificador de instrumentación teórico y se describe la metodología para su implementación en un AN221E04 con el software Anadigm Designer 2. Una vez implementado este modelo de amplificador de instrumentación se han efectuado una serie de pruebas con el objetivo de estudiar la capacidad de estos dispositivos. Dichas pruebas ponen de manifiesto que las FPAA´s tienen una serie de ventajas a tener en cuenta a la hora de realizar diseños analógicos. La precisión obtenida por el modelo de amplificador de instrumentación realizado es más que aceptable, llegando a obtener errores de ganancia inferiores al 1% con ganancias de 200V/V sin tener la necesidad de realizar grandes ajustes. En las conclusiones de este estudio se exponen tanto ventajas como inconvenientes de la utilización de FPAA´s en diseños analógicos. La principal ventaja de este uso es el ahorro de costes, ya que una vez desarrollada una plataforma de diseño, la capacidad de reconfiguración permite utilizar dicha plataforma para un amplio abanico de aplicaciones, reduciendo el número de componentes y simplificando las etapas de diseño. Como desventaja, las FPAA´s tienen una serie de limitaciones qué hay que tener en cuenta en ciertos casos pudiendo hacer irrealizable un diseño concreto; como puede ser el valor máximo o mínimo de ganancia. The FPAA's are programmable analog devices. These devices rely on the use of switched capacitors together with operational amplifiers. This type of technology has a number of advantages, because they combine the advantages of digital devices such as the reprogramming function of the variables of the surrounding environment, with the difference being analog devices, allowing the realization of a wide range of designs analog on a single chip. This project has conducted a study on the operation of the switched capacitor and its use in the device AN221E04 from Anadigm. Having described the architecture of AN221E04 and explained the basis for the operation of the switched capacitor, using the example models provided by Anadigm is developing an instrumentation amplifier theory model and describes the methodology for implementation in a AN221E04 with the Anadigm Designer 2 software. Once implemented this instrumentation amplifier model, have made a series of tests in order to study the ability of these devices. These tests show that the FPAA's have a number of advantages to take into account when making analog designs. The accuracy obtained by the instrumentation amplifier model is made more than acceptable, earning gain errors of less than 1% with gains of 200V / V without the need for major adjustments. The conclusions of this study are presented both advantages and disadvantages of using FPAA's in analog designs. The main advantage of this application is the cost savings, because once developed a platform for design, reconfiguration capability allows you to use this platform for a wide range of applications, reducing component count and simplifying design stages. As a disadvantage, the FPAA's have a number of limitations which must be taken into account in certain cases may make impossible a specific design, such as the maximum or minimum gain, or the magnitude of the possible settings.

Sistema de adquisición de datos compacto para medidas de extensiometría y posición

En este proyecto se trata el diseño y construcción de un sistema de adquisición de datos compacto y de bajo coste para medidas de extensiometría y posición. Dicho sistema irá embarcado en una bicicleta de montaña con el fin de medir determinados parámetros. Estos parámetros son a) Elongación de las suspensiones, b) Deformación en el cuadro. Para la medida de elongación de las suspensiones se diseña y construye un sensor casero de bajo coste basado en una transparencia y un par de diodos fotoemisor y fotorreceptor infrarrojos. Se imprime un gradiente y se emplean dos tubos coaxiales de PVC. La medida de extensiometría se realiza con galgas extensiométricas, puentes de Wheatstone y amplificador de instrumentación. Las muestras se digitalizan con el ADC del microcontrolador C8051F020 de la casa Silabs, que se usa en una placa de desarrollo, y se almacenan en una memoria flash serie. Se desarrolla un software para PC con LabView para poder recibir, procesar y visualizar las muestras obtenidas de los distintos canales con el fin de analizarlas. Se obtienen conclusiones de los resultados de pruebas básicas. ABSTRACT On this project, the design and construction of a compact, low cost, data adquisition system for strain and position measurements is dealt with. Such system will be embedded on a bicycle in order to measure certain parameters. These are a) Suspension elongation, b) Frame deformation. For suspension elongation measurements, a homemade, low cost sensor based on a photoemitter-photoreceiver diode couple and a transparent sheet is designed and built. A gradient is printed in the transparent sheet, and two coaxial PVC pipes are used. Strain measurements are carried out by means of a strain gage, Wheatstone bridges and an instrumentation amplifier. Samples are digitized with Silabs’ C8051F020’s ADC, which is used in a development board, and are stored in a serial flash memory. Software for PC on LabView is developed in order to receive, process and visualize the obtained samples from each channel in order to analyze them. Results are obtained from basic tests.

Development and programming of Geophonino: A low cost Arduino-based seismic recorder for vertical geophones

The commercial data acquisition systems used for seismic exploration are usually expensive equipment. In this work, a low cost data acquisition system (Geophonino) has been developed for recording seismic signals from a vertical geophone. The signal goes first through an instrumentation amplifier, INA155, which is suitable for low amplitude signals like the seismic noise, and an anti-aliasing filter based on the MAX7404 switched-capacitor filter. After that, the amplified and filtered signal is digitized and processed by Arduino Due and registered in an SD memory card. Geophonino is configured for continuous registering, where the sampling frequency, the amplitude gain and the registering time are user-defined. The complete prototype is an open source and open hardware system. It has been tested by comparing the registered signals with the ones obtained through different commercial data recording systems and different kind of geophones. The obtained results show good correlation between the tested measurements, presenting Geophonino as a low-cost alternative system for seismic data recording.

Direct ultrafast laser written C-band waveguide amplifier in Er-doped chalcogenide glass

This paper reports the fabrication and characterization of an ultrafast laser written Er-doped chalcogenide glass buried waveguide amplifier; Er-doped GeGaS glass has been synthesized by the vacuum sealed melt quenching technique. Waveguides have been fabricated inside the 4 mm long sample by direct ultrafast laser writing. The total passive fiber-to-fiber insertion loss is 2.58 +/- 0.02 dB at 1600 nm, including a propagation loss of 1.6 +/- 0.3 dB. Active characterization shows a relative gain of 2.524 +/- 0.002 dB/cm and 1.359 +/- 0.005 dB/cm at 1541 nm and 1550 nm respectively, for a pump power of 500 mW at a wavelength of 980 nm. (C) 2012 Optical Society of America

Regenerative amplifier with continuously variable pulse duration used in an optical parametric chirped-pulse amplification laser system for synchronous pumping

A Nd:glass regenerative amplifier has been set up to generate the pumping pulse with variable pulse width for an optical parametric chirped-pulse amplification (OPCPA) laser system. Each pulse of the pulse train from a cw self-mode-locking femtosecond Ti:sapphire oscillator is stretched to approximate to300 ps at 1062 nm to be split equally and injected into a nonlinear crystal and the Nd:glass regenerative amplifier, as the chirped signal pulse train and the seed pulse train of the pumping laser system, respectively. By adjusting the cavity length of the regenerative amplifier directly, the width of amplified pulse could be varied continuously from approximate to300 ps to approximate to3 ns. The chirped signal pulse for the OPCPA laser system and the seed pulse for the pumping laser system come from the same oscillator, so that the time jitter between the signal pulse and the pumping pulse in optical parametric amplification stages could be <10 ps. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

Laser beam automatic alignment in multipass amplifier

A laser beam automatic alignment system is applied in a multipass amplifier of the SG-III prototype laser. Considering the requirements of the SG-III prototype facility, by combining the general techniques of the laser beam automatic alignment system, according to the image relayed of the pinholes in the spatial filter, and utilizing the optical position and the spatial distribution of the four pinholes of the main spatial filter in the multipass amplifier of the SG-III prototype, a reasonable and optimized scheme for automatic aligning multipass beam paths is presented. It is demonstrated on the multipass amplifier experimental system. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

133-W pulsed fiber amplifier with large-mode-area fiber

A master-oscillator fiber power amplifier (MOPA) system with a 4-m-long Yb3+-doped homemade large mode area (LMA) double-clad fiber is reported. The system emits up to 133.8 W of amplified radiation at a wavelength of 1064 nm and a repetition rate of 100 kHz, limited only by the available pump power. Peak power of 300 kW at 20 kHz with a pulse duration of 15 ns is obtained. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

133-W pulsed fiber amplifier with large-mode-area fiber

A master-oscillator fiber power amplifier (MOPA) system with a 4-m-long Yb3+-doped homemade large mode area (LMA) double-clad fiber is reported. The system emits up to 133.8 W of amplified radiation at a wavelength of 1064 nm and a repetition rate of 100 kHz, limited only by the available pump power. Peak power of 300 kW at 20 kHz with a pulse duration of 15 ns is obtained. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

Broadband polarization-insensitive semiconductor optical amplifier gate with tensile InGaAs quasi-bulk and compressively strained InGaAs wells

A novel wideband polarization-insensitive semiconductor optical amplifier (SOA) gate containing compressively strained InGaAs quantum wells and tensile-strained InGaAs quasi-bulk layers is developed. The fabricated SOA gates have a wide 3-dB optical bandwidth of 102 nm, less than 0.8-dB polarization sensitivity, more than 50-dB extinction ratio, and less than 75-mA fiber-to-fiber lossless operating current. (C) 2004 Society of Photo-Optical Instrumentation Engineers.