Stress Ratio Effects on the fatigue Properties of Biaxially Loaded Tubular FRP-Specimens – Experimental Study

In this work tubular fiber reinforced specimens are tested for fatigue life. The specimens are biaxially loaded with tension and shear stresses, with a load angle β of 30° and 60° and a load ratio of R=0,1. There are many factors that affect fatigue life of a fiber reinforced material and the main goal of this work is to study the effects of load ratio R by obtaining S-N curves and compare them to the previous works (1). All the other parameters, such as specimen production, fatigue loading frequency and temperature, will be the same as for the previous tests. For every specimen, stiffness, temperature of the specimen during testing, crack counting and final fracture mode are obtained. Prior to testing, a study if the literature regarding the load ratio effects on composites fatigue life and with that review estimate the initial stresses to be applied in testing. In previous works (1) similar specimens have only been tested for a load ratio of R=-1 and therefore the behaviour of this tubular specimens for a different load ratio is unknown. All the data acquired will be analysed and compared to the previous works, emphasizing the differences found and discussing the possible explanations for those differences. The crack counting software, developed at the institute, has shown useful before, however different adjustments to the software parameters lead to different cracks numbers for the same picture, and therefore a better methodology will be discussed to improve the crack counting results. After the specimen’s failure, all the data will be collected and stored and fibre volume content for every specimen is also determinate. The number of tests required to make the S-N curves are obtained according to the existent standards. Additionally are also identified some improvements to the testing machine setup and to the procedures for future testing.

Identificación de tensiones iniciales en un macizo rocoso a partir de medidas de presión de agua en excavación de túneles

En las últimas décadas, dentro del mundo de la ingeniería civil, así como en otras disciplinas, se han desarrollado los métodos de identificación de parámetros. Esta técnica de estudio se basa en realizar un análisis inverso, el cual se lleva a cabo mediante técnicas probabilísticas normalmente, aunque existen otras técnicas para abordar el problema inverso. El objetivo final de la identificación de parámetros es a través de una serie de medidas realizar el análisis inverso y finalmente conocer que valor de un parámetro se ajusta mejor a las medidas realizadas.La mayoría de los trabajos asociados a la construcción de túneles han utilizado las medidas correspondientes a los desplazamientos para formular el problema de identificación. Dentro del presente trabajo se quiere profundizar en una vía de investigación poco desarrollada, la cual esta asociada a las medidas de presión de agua en la construcción de túneles. Las medidas de desplazamientos pueden presentar mayores desviaciones que las medidas de presión de agua, ya que las técnicas de auscultación causan una mayor distorsión de las condiciones iniciales en el caso de los

Internal stresses and textures of nanostructured alumina scales growing on polycrystalline Fe(3)Al alloy

The evolution of internal stresses in oxide scales growing on polycrystalline Fe(3)Al alloy in atmospheric air at 700 degrees C was determined using in situ energy-dispersive synchrotron X-ray diffraction. Ex situ texture analyses were performed after 5 h of oxidation at 700 degrees C. Under these conditions, the oxide-scale thickness, as determined by X-ray photoelectron spectroscopy, lies between 80 and 100 nm. The main phase present in the oxide scales is alpha-Al(2)O(3), with minor quantities of metastable theta-Al(2)O(3) detected in the first minutes of oxidation, as well as alpha-Fe(2)O(3). alpha-Al(2)O(3) grows with a weak (0001) fiber texture in the normal direction. During the initial stages of oxidation the scale develops, increasing levels of compressive stresses which later evolve to a steady state condition situated around -300 MPa. (C) 2010 International Centre for Diffraction Data. [DOI: 10.1154/1.3402764]

Numerical modelling of single-layer folding: clarification of an issue regarding the possible effect of computer codes and the influence of initial irregularities

The influence of initial perturbation geometry and material propel-ties on final fold geometry has been investigated using finite-difference (FLAC) and finite-element (MARC) numerical models. Previous studies using these two different codes reported very different folding behaviour although the material properties, boundary conditions and initial perturbation geometries were similar. The current results establish that the discrepancy was not due to the different computer codes but due to the different strain rates employed in the two previous studies (i.e. 10(-6) s(-1) in the FLAC models and 10(-14) s(-1) in the MARC models). As a result, different parts of the elasto-viscous rheological field were bring investigated. For the same material properties, strain rate and boundary conditions, the present results using the two different codes are consistent. A transition in Folding behaviour, from a situation where the geometry of initial perturbation determines final fold shape to a situation where material properties control the final geometry, is produced using both models. This transition takes place with increasing strain rate, decreasing elastic moduli or increasing viscosity (reflecting in each case the increasing influence of the elastic component in the Maxwell elastoviscous rheology). The transition described here is mechanically feasible but is associated with very high stresses in the competent layer (on the order of GPa), which is improbable under natural conditions. (C) 2000 Elsevier Science Ltd. All rights reserved.

Dibenzofuran degradation by Sphingomonas wittichii RW1 under environmental stresses

Sphingomonas wittichii is a gram-negative Alpha-proteobacterium, capable of degrading xenobiotic compounds such as dibenzofuran (DBF), dibenzo-p-dioxin, carbazole, 2-hydroxybiphenyl or nitro diphenyl ether herbicides. The metabolism of strain RW1 has been the subject of previous studies and a number of genes involved in DBF degradation have been characterized. It is known that RW1 posseses a unique initial DBF dioxygenase (encoded by the dxnAl gene) that catalyzes the first step in the degradation pathway. None of the organisms known to be able to degrade DBF have a similar dioxygenase, the closest match being the DBF dioxygenase from Rhodococcus sp. with an overall amino acid similarity of 45%. Genes participating in the conversion of the metabolite salicylate via the ortho-cleavage pathway to TCA cycle intermediates were identified as well. Apart from this scarce information, however, there is a lack of global knowledge on the genes that are involved in DBF degradation by strain RW1 and the influence of environmental stresses on DBF-dependent global gene expression. A global analysis is necessary, because it may help to better understand the behaviour of the strain under field conditions and suggest improvements for the current bioaugmentation practice. Chapter 2 describes the results of whole-genome analysis to characterize the genes involved in DBF degradation by RW1. Micro-array analysis allowed us to detect differences in gene transcription when strain RW1 was exposed to DBF. This was complemented by ultra-high throughput sequencing of mutants no longer capable of growing on salicylate and DBF. Some of the genes of the ortho-cleavage pathway were induced 2 to 4 times in the presence of DBF, as well as the initial DBF dioxygenase. However two gene clusters, named 4925 and 5102 were induced up to 19 times in response to DBF induction. The cluster 4925 is putatively participating in a meta-cleavage pathway while the cluster 5102 might be part of a gentisate pathway. The three pathways, ortho-cleavage, meta-cleavage and gentisate pathway seem to be active in parallel when strain RW1 is exposed to DBF, presenting evidence for a redundancy of genes for DBF degradation in the genome of RW1. Chapter 3 focuses on exploiting genetic tools to construct bioreporters representative for DBF degradation in RW1. A set of basic tools for genetic manipulation in Sphingomonas wittichii RW1 was tested and optimized. Both plasmids and mini-transposons were evaluated for their ability to be maintained in RW1 with or without antibiotic selection pressure, and for their ability to lead to fluorescent protein expression in strain RW1 from a constitutive promoter. Putative promoter regions of three of the previously found DBF-induced genes (Swit_4925, Swit_5102 and Swit_4897-dxnAl) were then used to construct eg/^-bioreporters in RW1. Chapter 4 describes the use of the constructed RW1-based bioreporter strains for examining the expression of the DBF degradation pathway genes under microcosm conditions. The bioreporter strains were first exposed to different carbon sources in liquid culture to calibrate the egfp induction. Contrary to our expectations from micro-array analysis only the construct with the promoter from gene cluster 4925 responded to DBF, whereas the other two constructs did not show specific induction with DBF. The response from the bioreporters was subsequently tested for sensitivity to water stress, given that this could have an important impact in soils. Exposure to liquid cultures with decreasing water potential, achieved by NaCl or PEG addition to the growth media, showed that eGFP expression in RW1 from the promoter regions 4925 and 5102 was not directly influenced by water stress, but only through an overall reduction in growth rate. In contrast, expression of eGFP from the dxnAl or an uspA promoter was also directly dependent on the extent of water stress. The RW1 with the 4925 construct was subsequently used in soil microcosms to evaluate DBF bioavailability to the cells in presence or absence of native microbiota or other contaminated material. We found that RW1 could grow on DBF added to soil, but bioreporter expression suggested that competition with native microbiota for DBF intermediates may limit its ability to proliferate to a maximum. Chapter 5 describes the results from the experiments carried out to more specifically detect genes of RW1 that might be implicated in water stress resistance. Hereto we created transposon mutagenesis libraries in RW1, either with a classical mini-Tn5 or with a variant that would express egfp when the transposon would insert in a gene induced under water stress. Classical mutant libraries were screened by replica plating under high and low water stress conditions (achieved by adding NaCl to the agar medium). In addition, we screened for smaller microcolonies formed by mutants in agarose beads that could be analized with flow cytometry. A number of mutants impaired to grow on NaCl-supplemented media were recovered and the transposon insertion sites sequenced. In a second procedure we screened by flow cytometry for mutants with a higher eGFP production after exposure to growth medium with higher NaCl concentrations. Mutants from both libraries rarely overlapped. Discovered gene functions of the transposon insertions pointed to compatible solute synthesis (glutamate and proline), cell membrane synthesis and modification of cell membrane composition. The results obtained in the present study give us a more complete picture of the mechanisms of DBF degradation by S. wittichii RW1, how it reacts to different DBF availability and how the DBF catabolic activity may be affected by the conditions found in contaminated environments. - Sphingomonas wittichii est une alpha-protéobactérie gram-négative, capable de dégrader des composés xénobiotiques tels que le dibenzofurane (DBF), la dibenzo-p-dioxine, le carbazole, le 2-hydroxybiphényle ou les herbicides dérivés du nitro-diphényléther. Le métabolisme de la souche RW1 a fait l'objet d'études antérieures et un certain nombre de gènes impliqués dans la dégradation du DBF ont été caractérisés. Il est connu que RW1 possède une unique dioxygénase DBF initiale (codée par le gène dxnAl) qui catalyse la première étape de la voie de dégradation. Aucun des organismes connus pour être capables de dégrader le DBF n'a de dioxygénase similaire. L'enzyme la plus proche étant la DBF dioxygénase de Rhodococcus sp. avec 45% d'acides aminés conservés. Les gènes qui participent à la transformation du salicylate en métabolites intermédiaires du cycle de Krebs par la voie ort/io-cleavage ont aussi été identifiés. Outre ces informations lacunaires, il y a un manque de connaissances sur l'ensemble des gènes impliqués dans la dégradation du DBF par la souche RW1 ainsi que l'effet des stress environnementaux sur l'expression génétique globale, en présence du DBF. Une analyse globale est nécessaire, car elle peut aider à mieux comprendre le comportement de la souche dans les conditions de terrain et de proposer des améliorations pour l'utilisation de la bio-augmentation comme technique de bio-remédiation. Le chapitre 2 décrit les résultats de l'analyse du génome pour caractériser les gènes impliqués dans la dégradation du DBF par RW1. Une analyse de micro-arrays nous a permis de détecter des différences dans la transcription des gènes lorsque la souche RW1 a été exposée au DBF. L'analyse a été complétée par le criblage à ultra-haut débit de mutants qui n'étaient plus capables de croître avec le salicylate ou le DBF comme seule source de carbone. Certains des gènes de la voie ortho-cleavage, dont la DBF dioxygénase initiale, ont xî été induits 2 à 4 fois, en présence du DBF. Cependant, deux groupes de gènes, nommés 4925 et 5102 ont été induits jusqu'à 19 fois en réponse au DBF. Le cluster 4925 participe probablement dans une voie de meta-cleavage tandis que le cluster 5102 pourrait faire partie d'une voie du gentisate. Les trois voies, ortho-cleavage, meta-cleavage et la voie du gentisate semblent être activées en parallèle lorsque la souche RW1 est exposée au DBF, ce qui représente une redondance de voies pour la dégradation du DBF dans le génome de RW1. Le chapitre 3 se concentre sur l'exploitation des outils génétiques pour la construction de biorapporteurs de la dégradation du DBF par RW1. Un ensemble d'outils de base pour la manipulation génétique dans Sphingomonas wittichii RW1 a été testé et optimisé. Deux plasmides et mini-transposons ont été évalués pour leur capacité à être maintenu dans RW1 avec ou sans pression de sélection par des antibiotiques, et pour leur capacité à exprimer la protéine fluorescente verte (eGFP) dans la souche RW1. Les trois promoteurs des gènes Swit_4925, Swit_5102 et Swit_4897 (dxnAl), induits en réponse au DBF, ont ensuite été utilisés pour construire des biorapporteurs dans RW1. Le chapitre 4 décrit l'utilisation des souches biorapportrices construites pour l'analyse de l'expression des gènes de la voie de dégradation du DBF dans des microcosmes avec différents types de sols. Les souches biorapportrices ont d'abord été exposées à différentes sources de carbone en cultures liquides afin de calibrer l'induction de la eGFP. La construction avec le promoteur du gène 4925 a permis une réponse au DBF. Mais contrairement à nos attentes, basées sur les résultats de l'analyse des micro-arrays, les deux autres constructions n'ont pas montré d'induction spécifique au DBF. La réponse des biorapporteurs a ensuite été testée pour la sensibilité au stress hydrique, étant donné que cela pourrait avoir un impact important dans les microcosmes. La diminution du potentiel hydrique en culture liquide est obtenue par addition de NaCl ou de PEG au milieu de croissance. Nous avons montré que l'expression de la eGFP contrôlée par les promoteurs 4925 et 5102 n'était pas directement influencée par le stress hydrique, mais seulement par une réduction globale des taux de croissance. En revanche, l'expression de la eGFP dépendante des promoteurs dxnAl et uspA était aussi directement dépendante de l'ampleur du stress hydrique. La souche avec la construction 4925 a été utilisée par la suite dans des microcosmes avec différents types de sols pour évaluer la biodisponibilité du DBF en présence ou absence des microbes indigènes et d'autres composés contaminants. Nous avons constaté que RW1 pouvait se développer si le DBF a été ajouté au sol, mais l'expression de la eGFP par le biorapporteur suggère que la compétition avec la microbiota indigène pour les métabolites intermédiaires du DBF peut limiter sa capacité à proliférer de manière optimale. Le chapitre 5 décrit les résultats des expériences réalisées afin de détecter spécifiquement les gènes de RW1 qui pourraient être impliquées dans la résistance au stress hydrique. Ici on a crée des bibliothèques de mutants de RW1 par transposon, soit avec un mini-Tn5 classique ou avec une variante qui exprime la eGFP lorsque le transposon s'insère dans un gène induit par le stress hydrique. Les bibliothèques de mutants ont été criblées par la méthode classique de repiquage sur boîtes, dans des conditions de stress hydrique élevé (obtenu par l'addition de NaCl dans les boîtes). En outre, nous avons criblé des micro¬colonies dans des billes d'agarose qui ont pu être analysées par cytométrie de flux. Un certain nombre de mutants déficients à croître sur des milieux supplémentés avec du NaCl ont été isolés et les sites d'insertion du transposon séquencés. Dans une deuxième procédure nous avons criblé par cytométrie de flux des mutants avec une production de eGFP supérieure, après exposition à un milieu de croissance avec une concentration élevée de NaCl. Les mutants obtenus dans les deux bibliothèques n'étaient pas similaires. Les fonctions des gènes où se trouvent les insertions de transposons sont impliqués dans la synthèse de solutés compatibles (glutamate et de la proline), dans la synthèse de la membrane cellulaire et dans la modification de la composition de la membrane cellulaire. Les résultats obtenus dans la présente étude nous donnent une image plus complète des mécanismes de dégradation du DBF par S. wittichii RW1, comment cette souche réagit à la disponibilité du DBF et comment l'activité catabolique peut être affectée par les conditions rencontrées dans des environnements contaminés.

Modeling of residual stresses and distortion due to welding in fillet welds

Welding has a growing role in modern world manufacturing. Welding joints are extensively used from pipes to aerospace industries. Prediction of welding residual stresses and distortions is necessary for accurate evaluation of fillet welds in relation to design and safety conditions. Residual stresses may be beneficial or detrimental, depending whether they are tensile or compressive and the loading. They directly affect the fatigue life of the weld by impacting crack growth rate. Beside theoretical background of residual stresses this study calculates residual stresses and deformations due to localized heating by welding process and subsequent rapid cooling in fillet welds. Validated methods are required for this purpose due to complexity of process, localized heating, temperature dependence of material properties and heat source. In this research both empirical and simulation methods were used for the analysis of welded joints. Finite element simulation has become a popular tool of prediction of welding residual stresses and distortion. Three different cases with and without preload have been modeled during this study. Thermal heat load set is used by calculating heat flux from the given heat input energy. First the linear and then nonlinear material behavior model is modeled for calculation of residual stresses. Experimental work is done to calculate the stresses empirically. The results from both the methods are compared to check their reliability. Residual stresses can have a significant effect on fatigue performance of the welded joints made of high strength steel. Both initial residual stress state and subsequent residual stress relaxation need to be considered for accurate description of fatigue behavior. Tensile residual stresses are detrimental and will reduce the fatigue life and compressive residual stresses will increase it. The residual stresses follow the yield strength of base or filler material and the components made of high strength steel are typically thin, where the role of distortion is emphasizing.

A critical assessment of unbalanced surface stresses: Some complementary considerations

The wide-ranging survey of twisted growth in polymers by Lotz and Cheng cites extensive evidence consistent with the relief of surface stress being the underlying cause. This complementary note contributes to the discussion by making three main points. First, it is necessary to go further and explain the key issue of how a consistent twist is maintained when, as commonly, this habit has a lower symmetry than the crystallographic lattice. Detailed study has shown that, in polyethylene, this occurs by reorganization of the initial fold surfaces. Second, the suggested explanation by Keith and Padden that. in polyethylene, the asymmetric habit derives from molecules adding to lamellae with inclined fold surfaces is invalid being doubly inconsistent with observation. Third, twisting has now been linked to faster growth by study of row structures in polyethylene. This produces inherently rough fold surfaces in Regime II whose internal stresses drive reorganization and twisting. For slower (Regime I) growth, fold surfaces form with and maintain ordered packing so providing no basis for twisting. These new insights radically alter the context of twisted growth and provide a firm factual basis for further work. (c) 2005 Elsevier Ltd. All rights reserved.

Measurement of LSP-induced residual stresses and fatigue life on thin-walled aluminium alloys specimens

This thesis work encloses activities carried out in the Laser Center of the Polytechnic University of Madrid and the laboratories of the University of Bologna in Forlì. This thesis focuses on the superficial mechanical treatment for metallic materials called Laser Shock Peening (LSP). This process is a surface enhancement treatment which induces a significant layer of beneficial compressive residual stresses underneath the surface of metal components in order to improve the detrimental effects of the crack growth behavior rate in it. The innovation aspect of this work is the LSP application to specimens with extremely low thickness. In particular, after a bibliographic study and comparison with the main treatments used for the same purposes, this work analyzes the physics of the operation of a laser, its interaction with the surface of the material and the generation of the surface residual stresses which are fundamentals to obtain the LSP benefits. In particular this thesis work regards the application of this treatment to some Al2024-T351 specimens with low thickness. Among the improvements that can be obtained performing this operation, the most important in the aeronautic field is the fatigue life improvement of the treated components. As demonstrated in this work, a well-done LSP treatment can slow down the progress of the defects in the material that could lead to sudden failure of the structure. A part of this thesis is the simulation of this phenomenon using the program AFGROW, with which have been analyzed different geometric configurations of the treatment, verifying which was better for large panels of typical aeronautical interest. The core of the LSP process are the residual stresses that are induced on the material by the interaction with the laser light, these can be simulated with the finite elements but it is essential to verify and measure them experimentally. In the thesis are introduced the main methods for the detection of those stresses, they can be mechanical or by diffraction. In particular, will be described the principles and the detailed realization method of the Hole Drilling measure and an introduction of the X-ray Diffraction; then will be presented the results I obtained with both techniques. In addition to these two measurement techniques will also be introduced Neutron Diffraction method. The last part refers to the experimental tests of the fatigue life of the specimens, with a detailed description of the apparatus and the procedure used from the initial specimen preparation to the fatigue test with the press. Then the obtained results are exposed and discussed.

Cyclic behaviour of saturated sands subject to previous horizontal shear stresses

The dynamic behaviour of saturated sands has been studied from different perspectives. However, most experimental research on this field does not take into account the shear stress conditions existing prior to the application of dynamic loads; i.e., a null initial static shear stress (τo = 0) is assumed. The main objective of this work is to report on the influence that static shear stresses (τo) have on the behaviour of saturated sands under cyclic shear loads. This article presents the results and analysis of part of a wider experimental programme involving 30 monotonic and 26 cyclic simple shear tests for different combinations of static shear stress (τo) and cyclic shear stress (τc) (all undrained), besides identification and classification tests. The tested samples have been taken from the area of the North Entrance Mouth at the Port of Barcelona (Spain).

Dynamic behavior of cylindrical shells under initial stress,

"Project no. 9782. Contract AF 49 (638)-430 ... CU-11-60-AF-430-CE."

Evaluation Of Soft-tissue Lesions With (18)f-fdg Pet/ct: Initial Results Of A Prospective Trial.

Although MRI is utilized for planning the resection of soft-tissue tumors, it is not always capable of differentiating benign from malignant lesions. The risk of local recurrence of soft-tissue sarcomas is increased when biopsies are performed before resection and by inadequate resections. PET associated with computed tomography using fluorodeoxyglucose labeled with fluorine-18 ((18)F-FDG PET/CT) may help differentiate between benign and malignant tumors, thus avoiding inadequate resections and making prior biopsies unnecessary. The purpose of this study was to evaluate the usefulness of (18)F-FDG PET/CT in differentiating benign from malignant solid soft-tissue lesions. Patients with solid lesions of the limbs or abdominal wall detected by MRI were submitted to (18)F-FDG PET/CT. The maximum standardized uptake value (SUVmax) cutoff was determined to differentiate malignant from benign tumors. Regardless of the (18)F-FDG PET/CT results all patients underwent biopsy and surgery. MRI was performed in 54 patients, and 10 patients were excluded because of purely lipomatose or cystic lesions. (18)F-FDG PET/CT was performed in the remaining 44 patients. Histopathology revealed 26 (59%) benign and 18 (41%) malignant soft-tissue lesions. A significant difference in SUVmax was observed between benign and malignant soft-tissue lesions. The SUVmax cutoff of 3.0 differentiated malignant from benign lesions with 100% sensitivity, 83.3% specificity, 89.6% accuracy, 78.3% positive predictive value, and 100% negative predictive value. (18)F-FDG PET/CT seems to be able to differentiate benign from malignant soft-tissue lesions with good accuracy and very high negative predictive value. Incorporating (18)F-FDG PET/CT into the diagnostic algorithm of these patients may prevent inadequate resections and unnecessary biopsies.

Value Of Sentinel Lymph Node Biopsy In Papillary Thyroid Cancer: Initial Results Of A Prospective Trial.

The objectives of the study were to evaluate the performance of sentinel lymph node biopsy (SLNB) in detecting occult metastases in papillary thyroid carcinoma (PTC) and to correlate their presence to tumor and patient characteristics. Twenty-three clinically node-negative PTC patients (21 females, mean age 48.4 years) were prospectively enrolled. Patients were submitted to sentinel lymph node (SLN) lymphoscintigraphy prior to total thyroidectomy. Ultrasound-guided peritumoral injections of (99m)Tc-phytate (7.4 MBq) were performed. Cervical single-photon emission computed tomography and computed tomography (SPECT/CT) images were acquired 15 min after radiotracer injection and 2 h prior to surgery. Intra-operatively, SLNs were located with a gamma probe and removed along with non-SLNs located in the same neck compartment. Papillary thyroid carcinoma, SLNs and non-SLNs were submitted to histopathology analysis. Sentinel lymph nodes were located in levels: II in 34.7 % of patients; III in 26 %; IV in 30.4 %; V in 4.3 %; VI in 82.6 % and VII in 4.3 %. Metastases in the SLN were noted in seven patients (30.4 %), in non-SLN in three patients (13.1 %), and in the lateral compartments in 20 % of patients. There were significant associations between lymph node (LN) metastases and the presence of angio-lymphatic invasion (p = 0.04), extra-thyroid extension (p = 0.03) and tumor size (p = 0.003). No correlations were noted among LN metastases and patient age, gender, stimulated thyroglobulin levels, positive surgical margins, aggressive histology and multifocal lesions. Sentinel lymph node biopsy can detect occult metastases in PTC. The risk of a metastatic SLN was associated with extra-thyroid extension, larger tumors and angio-lymphatic invasion. This may help guide future neck dissection, patient surveillance and radioiodine therapy doses.

In Vivo Evaluation Of The Genetic Toxicity Of Rubus Niveus Thunb. (rosaceae) Extract And Initial Screening Of Its Potential Chemoprevention Against Doxorubicin-induced Dna Damage.

Rubus niveus Thunb. plant belongs to Rosaceae family and have been used traditionally to treat wounds, burns, inflammation, dysentery, diarrhea and for curing excessive bleeding during menstrual cycle. The present study was undertaken to investigate the in vivo genotoxicity of Rubus niveus aerial parts extract and its possible chemoprotection on doxorubicin (DXR)-induced DNA damage. In parallel, the main phytochemicals constituents in the extract were determined. The animals were exposed to the extract for 24 and 48h, and the doses selected were 500, 1000 and 2000mg/kg b.w. administered by gavage alone or prior to DXR (30mg/kg b.w.) administered by intraperitoneal injection. The endpoints analyzed were DNA damage in bone marrow and peripheral blood cells assessed by the alkaline alkaline (pH>13) comet assay and bone marrow micronucleus test. The results of chemical analysis of the extract showed the presence of tormentic acid, stigmasterol, quercitinglucoronide (miquelianin) and niga-ichigoside F1 as main compounds. Both cytogenetic endpoints analyzed showed that there were no statistically significant differences (p>0.05) between the negative control and the treated groups with the two higher doses of Rubus niveus extract alone, demonstrating absence of genotoxic and mutagenic effects. Aneugenic/clastogenic effect was observed only at 2000mg/kg dose. On the other hand, in the both assays and all tested doses were observed a significant reduction of DNA damage and chromosomal aberrations in all groups co-treated with DXR and extract compared to those which received only DXR. These results indicate that Rubus niveus aerial parts extract did not revealed any genotoxic effect, but presented some aneugenic/clastogenic effect at higher dose; and suggest that it could be a potential adjuvant against development of second malignant neoplasms caused by the cancer chemotherapic DXR.

Nitrogen Starvation For Lipid Accumulation In The Microalga Species Desmodesmus Sp.

Recently, to obtain lipids from microalgae has been the object of extensive research, since it is viewed as a promising feedstock for biodiesel production, especially when compared with crops such as soybean and sunflower, in terms of theoretical performance. The reduction of nutrient availability in culture media, especially nitrogen, stresses the microorganisms and affects cell growth, thus inducing lipid accumulation. This is an interesting step in biodiesel feedstock obtention from microalgae and should be better understood. In this study, four levels of nitrogen concentration in the BG-11 culture medium were evaluated in the growth of the chlorophycean microalga Desmodesmus sp. Both cell growth and lipid content were monitored over 7 days of cultivation, which yielded a final cell density of 33 × 10(6) cells mL(-1) with an initial NaNO3 concentration of 750 mg L(-1) in the medium and a maximum lipid content of 23 % with total nitrogen starvation. It was observed that the microalgae presented high lipid accumulation in the fourth day of cultivation with nitrogen starvation, although with moderate cell growth.

Central retinal vein thrombosis as an initial manifestation of heterozygous protein C deficiency: case report

The purpose of this paper is to report a case of central retinal vein thrombosis associated with isolated heterozygous protein C deficiency. Acute occlusion of the central retinal vein presents as one of the most dramatic pictures in ophthalmology. It is often a result of both local and systemic causes. A rare systemic cause is heterozygous protein C deficiency, and it usually occurs in combination with other thrombophilic conditions. This case highlights that isolated heterozygous protein C deficiency may be the cause of central retinal vein thrombosis and underscores the importance of its screening in young patients with this ophthalmologic disease.