Converter-Fed Induction Motor Losses: Determination With IEC Methods

Energy efficiency is an important topic when considering electric motor drives market. Although more efficient electric motor types are available, the induction motor remains as the most common industrial motor type. IEC methods for determining losses and efficiency of converter-fed induction motors were introduced recently with the release of technical specification IEC/TS 60034-2-3. Determining the induction motor losses with IEC/TS 60034-2-3 method 2-3-A and assessing the practical applicability of the method are the main interests of this study. The method 2-3-A introduces a specific test converter waveform to be used in the measurements. Differences between the induction motor losses with a test converter supply, and with a DTC converter supply are investigated. In the IEC methods, the tests are run at motor rated fundamental voltage, which, in practice, requires the frequency converter to be fed with a risen input voltage. In this study, the tests are run on both frequency converters with artificially risen converter input voltage, resulting in rated motor fundamental input voltage as required by IEC. For comparison, the tests are run with both converters on normal grid input voltage supply, which results in lower motor fundamental voltage and reduced flux level, but should be more relevant from practical point of view. According to IEC method 2-3-A, tests are run at rated motor load, and to ensure comparability of the results, the rated load is used in the grid-fed converter measurements, although motor is overloaded while producing the rated torque at reduced flux level. The IEC 2-3-A method requires also sinusoidal supply test results with IEC method 2-1-1B. Therefore, the induction motor losses with the recently updated IEC 60034-2-1 method 2-1-1B are determined at the motor rated voltage, but also at two lower motor voltages, which are according to the output fundamental voltages of the two network-supplied converters. The method 2-3-A was found to be complex to apply but the results were stable. According to the results, the method 2-3-A and the test converter supply are usable for comparing losses and efficiency of different induction motors at the operating point of rated voltage, rated frequency and rated load, but the measurements do not give any prediction of the motor losses at final application. One might therefore strongly criticize the method’s main principles. It seems, that the release of IEC 60034-2-3 as a technical specification instead of a final standard for now was justified, since the practical relevance of the main method is questionable.

Validation of an hplc method for the determination of 1,7-dihydroxy-2,3-methylenedioxyxanthone in extracts obtained from Polygala cyparissias A. St. Hil. & Moq. (Polygalaceae) and evaluation of the influence of its content on the gastroprotective activity

Polygala cyparissias is a plant widespread in Southern Latin America. Recently, we demonstrated the gastroprotective activity of the extract, as well as for one of the isolated metabolites-1,7-dihydroxy-2,3-methylenedioxyxanthone (MDX). In this study, a HPLC method for the quantification of MDX was validated. The HPLC method was linear (0.5-24 µg mL-1 of MDX) with good accuracy, precision and robustness. The content of MDX in the extracts from whole and different parts of the plant ranged from 0 to 5.4 mg g-1 and the gastroprotective index ranged from 72.1 to 99.1%. Thus, the method might be used for the standardization of the extracts based on the MDX marker.

Antioxidant Capacity of 2-(3,5-diaryl-4,5-dihydro-1H-pyrazol-1-yl)-4-phenylthiazoles

The antioxidant capacity of 2-(3,5-diaryl-4,5-dihydro-1H-pyrazol-1-yl)-4-phenylthiazoles was evaluated. The values of antioxidant capacities of compounds 2d and 2e were found to be, respectively, 2,700 +/- 150 and 3,135 +/- 230 TE by the ORAC method, corresponding to a significant antioxidant capacity.

Síntese de novas tieno[3,2-b]piridinas com potencial atividade biológica contendo 1,2,3-triazoles 1,4-dissubstituídos obtidos por reação "click" de ciclioadição azida-alquino catalisada por Cu(I)-CuAAC

Dissertação de mestrado em Química Medicinal

Primate adult brain cell autotransplantation produces behavioral and biological recovery in 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine-induced parkinsonian St. Kitts monkeys.

The potential for "replacement cells" to restore function in Parkinson's disease has been widely reported over the past 3 decades, rejuvenating the central nervous system rather than just relieving symptoms. Most such experiments have used fetal or embryonic sources that may induce immunological rejection and generate ethical concerns. Autologous sources, in which the cells to be implanted are derived from recipients' own cells after reprogramming to stem cells, direct genetic modifications, or epigenetic modifications in culture, could eliminate many of these problems. In a previous study on autologous brain cell transplantation, we demonstrated that adult monkey brain cells, obtained from cortical biopsies and kept in culture for 7 weeks, exhibited potential as a method of brain repair after low doses of 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP) caused dopaminergic cell death. The present study exposed monkeys to higher MPTP doses to produce significant parkinsonism and behavioral impairments. Cerebral cortical cells were biopsied from the animals, held in culture for 7 weeks to create an autologous neural cell "ecosystem" and reimplanted bilaterally into the striatum of the same six donor monkeys. These cells expressed neuroectodermal and progenitor markers such as nestin, doublecortin, GFAP, neurofilament, and vimentin. Five to six months after reimplantation, histological analysis with the dye PKH67 and unbiased stereology showed that reimplanted cells survived, migrated bilaterally throughout the striatum, and seemed to exert a neurorestorative effect. More tyrosine hydroxylase-immunoreactive neurons and significant behavioral improvement followed reimplantation of cultured autologous neural cells as a result of unknown trophic factors released by the grafts. J. Comp. Neurol. 522:2729-2740, 2014. © 2014 Wiley Periodicals, Inc.

Espectro infravermelho e análise conformacional do composto 3-fenil-2-oxo-1,2,3-oxatiazolidina

The infrared (IR) spectra of the four distict conformers located on the multidimensional potential energy surface (PES) for the 3-phenyl-1,2,3-oxathiazolidine 2-oxide compound have been calculated using the semiempirical quantum-mechanical method PM3. The band spectra are reported and compared directly with the experimental spectrum. The IR intensities are shown to be much more sensitive to conformational changes than the vibrational frequencies and so, the theoretical analysis of the IR spectrum can be used as a tool for helping in the elucidation of the structure of heterocyclic compounds.

SYNTHESIS AND BIOLOGICAL EVALUATION OF SPIRO[INDOLINE-3,4’-PYRANO[2,3-C:6,5-C’]DIPYRAZOL]- 2-ONES IN THE PRESENCE OF SBA-Pr-SO3H AS A NANOCATALYST

Sulfonic acid functionalized SBA-15 nanoporous material (SBA-Pr-SO3H) with a large pore size of 6 nm, a high surface area, high selectivity, and excellent chemical and thermal stability was applied as an efficient heterogeneous nanoporous acid catalyst in the reaction of isatin with pyrazolones under mild reaction conditions. A novel class of symmetrical spiro[indoline-3,4'-pyrano[2,3-c:6,5-c']dipyrazol]-2-one derivatives was successfully obtained in high yields. Comparison of these results with those reported in the literature shows that the current method is efficient, and results in better reaction times and yields of the desired products. Other advantages of this new method are its operational simplicity, easy work-up procedure, and the use of SBA-Pr-SO3H as a reusable and environmentally benign nanoreactor, such that the reaction proceeds easily in its nanopores. We also tested the antimicrobial activity of the prepared compounds using the disc diffusion method, and some of the synthesized compounds exhibited the best results against B. subtilis and S. aureus.

Narrow-band 1, 2, 3, 4, 8, 16 and 24 cycles/360º angular frequency filters

We measured human frequency response functions for seven angular frequency filters whose test frequencies were centered at 1, 2, 3, 4, 8, 16 or 24 cycles/360º using a supra-threshold summation method. The seven functions of 17 experimental conditions each were measured nine times for five observers. For the arbitrarily selected filter phases, the maximum summation effect occurred at test frequency for filters at 1, 2, 3, 4 and 8 cycles/360º. For both 16 and 24 cycles/360º test frequencies, maximum summation occurred at the lower harmonics. These results allow us to conclude that there are narrow-band angular frequency filters operating somehow in the human visual system either through summation or inhibition of specific frequency ranges. Furthermore, as a general result, it appears that addition of higher angular frequencies to lower ones disturbs low angular frequency perception (i.e., 1, 2, 3 and 4 cycles/360º), whereas addition of lower harmonics to higher ones seems to improve detection of high angular frequency harmonics (i.e., 8, 16 and 24 cycles/360º). Finally, we discuss the possible involvement of coupled radial and angular frequency filters in face perception using an example where narrow-band low angular frequency filters could have a major role.

Synthèse diastéréosélective et énantiosélective de dérivés cyclopropaniques 1,2,3-substitués à l’aide de carbénoïdes gem-dizinciques

Les dérivés cyclopropaniques 1,2,3-substitutés sont des composés intéressants dans de nombreux domaines de la chimie. Au cours de cet ouvrage, nous nous sommes intéressés à la synthèse, tout d’abord diastéréosélective puis énantiosélective de ces composés. Nous nous sommes en particulier intéressés à l’utilisation de la zinciocyclopropanation pour l’obtention de ces dérivés cyclopropaniques 1,2,3-substitutés. Cette méthode consiste en l’utilisation d’un carbénoïde gem-dizincique pour effectuer une réaction de type Simmons-Smith. Cette stratégie a l’avantage d’être diastéréosélective favorisant la formation du zinciocyclopropane dont l’atome de zinc est dans une configuration cis avec le groupement directeur qu’est l’oxygène allylique basique. Lors de cette réaction, l’existence d’une réaction compétitive avec un réactif monozincique diminuait l’utilité de la zinciocyclopropanation. L’issue de la réaction s’est avérée dépendre fortement de la nature du carbénoïde utilisé, de la température réactionnelle et de la présence de ZnI2 dans le milieu. L’étude par GCMS de nombreuses conditions pour la formation des différents carbénoïdes a permis d’identifier les paramètres clés conduisant à la zinciocyclopropanation. Ces découvertes ont notamment permis d’étendre la réaction de zinciocyclopropanation aux alcools allyliques portant un seul groupement directeur (ie. non dérivé du 1,4-buténediol). Dans ces conditions, la réaction s’est avérée extrêmement diastéréosélective favorisant la formation du zinciocyclopropane dont l’atome de zinc est dans une configuration cis avec le groupement directeur. Afin de fonctionnaliser les zinciocyclopropanes ainsi obtenus, plusieurs réactions de fonctionnalisation in situ ont été développées. Chacune de ces méthodes a montré une conservation totale de la diastéréosélectivité obtenue lors de la réaction de zinciocyclopropanation. La versatilité de la zinciocyclopropanation a donc été démontrée. Avec une méthode diastéréosélective efficace pour la formation de zinciocyclopropanes à partir d’alcools allyliques ne portant qu’un seul groupement directeur, il est devenu possible d’envisager le développement énantiosélectif de la réaction. L’utilisation d’un dioxaborolane énantiopur a permis la zinciocyclopropanation avec de très bons excès énantiomères de divers alcools allyliques chiraux. La présence sur la même molécule d’un lien C–Zn nucléophile est d’un atome de bore électrophile a conduit à un échange bore-zinc in situ, formant un cyclopropylborinate énantioenrichi. La formation de ce composé bicyclique a permis d’obtenir une diastéréosélectivité parfaite. De nombreux alcools allyliques ont pu ainsi être convertis en cyclopropylborinates. Une réaction de Suzuki subséquente a permis la formation de dérivés cyclopropaniques 1,2,3-trisubstitués avec de très bons excès énantiomères et une excellente diastéréosélectivité. Les cyclopropylborinates obtenus à l’issue de la zinciocyclopropanation énantiosélective se sont avérés être des unités très versatiles puisque de nombreuses méthodes ont pu être développés pour leur fonctionnalisation.

Les esters cyclopropane-1,1-dicarboxyliques et les dérivés cyclopropaniques 1,2,3-substitués : synthèses et applications

Les cyclopropanes sont des motifs d’une grande importance puisqu’ils sont présents dans plusieurs molécules biologiquement actives en plus d’être de puissants intermédiaires dans la synthèse de molécules complexes. Au cours de cet ouvrage, nous avons développé une nouvelle méthode générale pour la synthèse d’ylures d’iodonium de malonates, soit d’importants précurseurs d’esters cyclopropane-1,1-dicarboxyliques. Ainsi, à l’aide de ces ylures, une méthode très efficace pour la synthèse d’esters cyclopropane-1,1-dicarboxyliques racémiques a été développée. Des travaux ont aussi été entrepris pour la synthèse énantiosélective de ces composés. Par ailleurs, les esters cyclopropane-1,1-dicarboxyliques ont été utilisés dans le développement de deux nouvelles méthodologies, soit dans une réaction de cycloaddition (3+3) avec des imines d’azométhines et dans la formation d’allènes par l’addition-1,7 de cuprates. Nous avons aussi poursuivi l’étude synthétique du cylindrocyclophane F impliquant l’utilisation de cyclopropanes pour le contrôle des centres chiraux. Ainsi l’addition-1,5 d’un cuprate sur un ester cyclopropane-1,1-dicarboxylique a été utilisée comme l’une des étapes clés de notre synthèse. L’autre centre chiral a pu être contrôlé par l’hydrogénolyse sélective d’un cyclopropylméthanol. Ces études ont, par ailleurs, mené au développement d’une nouvelle réaction d’arylcyclopropanation énantiosélective utilisant des carbénoïdes de zinc générés in situ à partir de réactifs diazoïques. Cette méthode permet d’accéder très efficacement aux cyclopropanes 1,2,3-substitués. De plus, nous avons développé la première réaction de Simmons-Smith catalytique en zinc menant à un produit énantioenrichi.

Stille reactions of 2,3-bis(stannyl)butenoates: an unexpected regioselectivity

The palladium-catalyzed cross-coupling reaction of methyl (Z)-2,3-bis(tributylstannyl)butenoate with aryl iodides is regioselective, leading to 2-aryl-3-stannylated products; this selectivity is the opposite to that observed in the reaction between halides and 3,4-bis(stannyl)furan-2(5H)-one. Since the resulting butenoates can be converted into the corresponding furanones, the method provides useful flexibility in the preparation of functionalized butenoates and furanones.

A new class of ammonium ylid for [2,3]-sigmatropic rearrangement reactions: ene-endo-spiro ylids

The first examples of sigmatropic rearrangements of ene-endo-spirocyclic, tetrahydropyridine-derived ammonium ylids are reported. Thus, spiro[6.7]-ylids rearrange primarily by a [2,3]-pathway, whereas the analogous [6.6]-ylids rearrange by [1,2]- and [2,3]-mechanisms in roughly equal proportions. This method serves as a rapid entry to the core of a range of alkaloids bearing a pyrrolo[1,2-a]azepine or octahydroindolizidine nucleus.

Asymmetric [2,3]-rearrangement of glycine-derived allyl ammonium ylids

The first examples of highly enantioselective [2,3]-sigmatropic rearrangements of acyclic allylic ammonium ylids are reported. Thus, a range of N-{2‘-[(N‘-allyl-N‘,N‘-dialkyl)ammonium]}acetyl camphor sultams undergo rearrangement at 0 °C in DME solution with high diastereofacial control (up to 99:1 dr) to give allylglycines in generally high yield. The power of the method has been demonstrated in a rapid and efficient synthesis of (R)-allyl glycine.

Zinc mediated azide-alkyne ligation to 1,5- and 1,4,5-substituted 1,2,3-triazoles

A mild method for regioselective formation of 1,5-substituted 1,2,3-triazoles is described. The zinc-mediated reaction works at room temperature and is successful across a wide range of azido/alkynyl substrates. Additionally, the triazole 4-position can be further functionalized through the intermediate aryl-zinc to accommodate a diverse three-component coupling strategy.