Valorization of grape pomace through hot compressed water extraction/hydrolysis

The world energy consumption is expected to increase strongly in coming years, because of the emerging economies. Biomass is the only renewable carbon resource that is abundant enough to be used as a source of energy Grape pomace is one of the most abundant agro-industrial residues in the world, being a good biomass resource. The aim of this work is the valorization of grape pomace from white grapes (WWGP) and from red grapes (RWGP), through the extraction of phenolic compounds with antioxidant activity, as well as through the extraction/hydrolysis of carbohydrates, using subcritical water, or hot compressed water (HCW). The main focus of this work is the optimization of the process for WWGP, while for RWGP only one set of parameters were tested. The temperatures used were 170, 190 and 210 °C for WWGP, and 180 °C for RWGP. The water flow rates were 5 and 10 mL/min, and the pressure was always kept at 100 bar. Before performing HCW assays, both residues were characterized, revealing that WWGP is very rich in free sugars (around 40%) essentially glucose and fructose, while RWGP has higher contents of structural sugars, lignin, lipids and protein. For WWGP the best results were achieved at 210 °C and 10 mL/min: higher yield in water soluble compounds (69 wt.%), phenolics extraction (26.2 mg/g) and carbohydrates recovery (49.3 wt.% relative to the existing 57.8%). For RWGP the conditions were not optimized (180 °C and 5 mL/min), and the values of the yield in water soluble compounds (25 wt.%), phenolics extraction (19.5 mg/g) and carbohydrates recovery (11.4 wt.% relative to the existing 33.5%) were much lower. The antioxidant activity of the HCW extracts from each assay was determined, the best result being obtained for WWGP, namely for extracts obtained at 210 °C (EC50=20.8 μg/mL; EC50 = half maximum effective concentration; EC50 = 22.1 μg/mL for RWGP, at 180 ºC).

Valorization of grape pomace residues integrating hot compressed water with biotechnology

Dissertação para obtenção do grau de Mestre em Biotecnologia

Evaluating the potential of yeast strains to produce added value products for the food and/or pharmaceutical industries

This study focus in the valorization of the apple pomace with the main goal of obtaining added value products. For that, hot compressed water technology was used for the extraction of phenolic compounds and hydrolysis of polysaccharides presents in the lignocellulosic structure of apple pomace to obtain simple sugars. The sugars have been utilized as alternative carbon source for growth, lipid accumulation and carotenoids production by five different yeast Yarrowia lipolytica, Rhodotorula mucilaginosa, Rhodotorula glutinis, Rhodosporidium babjevae and Rhodosporidium toruloides. Hydrolysis experiments were carried out with constant pressure of 100 bar, flow rate of 2mL/min and temperatures between 50°C and 250°C. The amount of total sugars present in apple pomace hydrolysates showed maximum values for the hydrolysis temperatures of 110°C and 190°C. In fact, these temperatures revealed the best results regarding the monosaccharides quantities. The amount of 5-HMF and furfural in each hydrolysate varied through the different temperatures. Maximum values for 5-HMF were obtained with 170°C, while furfural showed to be maximum at 210°C. Extraction of phenolic compounds were performed in simultaneously with hydrolysis reactions. Total phenolic compounds (TPC) increased along the temperature, however with small variations between 170°C and 250°C. Hydrolysates were then used as alternative carbon source to yeast growth. R. mucilaginosa shows the highest optical density, with the hydrolysate obtained at 130°C. Carotenoids produced by these yeast scored a total of 7.02μg carotenoids/g cell dry weight, while for the control assay, the same yeast scored 9.31μg caratonoides/g cell dry weight. β-carotene was quantified by HPLC, were 33% of the carotenoid production by R. mucilaginosa with hydrolysate as carbon source, corresponded to β-caroteno.

Prediction of the chemical composition of lamb carcasses from multi-frequency impedance data

Multi-frequency bioimpedance analysis (MFBIA) was used to determine the impedance, reactance and resistance of 103 lamb carcasses (17.1-34.2 kg) immediately after slaughter and evisceration. Carcasses were halved, frozen and one half subsequently homogenized and analysed for water, crude protein and fat content. Three measures of carcass length were obtained. Diagonal length between the electrodes (right side biceps femoris to left side of neck) explained a greater proportion of the variance in water mass than did estimates of spinal length and was selected for use in the index L-2/Z to predict the mass of chemical components in the carcass. Use of impedance (Z) measured at the characteristic frequency (Z(c)) instead of 50 kHz (Z(50)) did not improve the power of the model to predict the mass of water, protein or fat in the carcass. While L-2/Z(50) explained a significant proportion of variation in the masses of body water (r(2) 0.64), protein (r(2) 0.34) and fat (r(2) 0.35), its inclusion in multi-variate indices offered small or no increases in predictive capacity when hot carcass weight (HCW) and a measure of rib fat-depth (GR) were present in the model. Optimized equations were able to account for 65-90 % of the variance observed in the weight of chemical components in the carcass. It is concluded that single frequency impedance data do not provide better prediction of carcass composition than can be obtained from measures of HCW and GR. Indices of intracellular water mass derived from impedance at zero frequency and the characteristic frequency explained a similar proportion of the variance in carcass protein mass as did the index L-2/Z(50).

Equações de predição da composição química corporal a partir do corte da 9-10-11ª costelas de bovinos castrados Nelore

Objetivou-se obter equações de regressão linear simples para estimativa da composição química corporal de novilhos Nelore a partir da composição química do corte da 9-10-11ª costelas. Foram utilizados 27 bovinos em confinamento, com 21 a 31 meses de idade e 338,0 a 503,6 kg de peso corporal. do total, foram abatidos seis animais (referência) ao início do experimento para estimativa da composição química corporal. A composição química em água, proteína, EE e cinzas foi determinada no corte da 9-10-11ª costelas e nos tecidos corporais. As equações de regressão para estimativa do peso de corpo vazio (PCVZ) a partir dos pesos de jejum (PV) e carcaça quente (PCQ) foram PCVZ = 0,8726 PV - 2,7399 e PCVZ = 1,5350 PCQ + 13,598 (R² = 0,98). O ganho de 1 kg de PCVZ correspondeu a aproximadamente 1,15 kg de PV. A porcentagem de água no corpo vazio (CVz) esteve altamente correlacionada às porcentagens de água (R² = 0,98) e EE (R² = 0,91) no corte das costelas. A equação mais indicada foi a desenvolvida a partir da porcentagem de água no corte das costelas (Sx, y = 0,46). Verificou-se alta correlação entre a porcentagem de EE no CVz e a porcentagem de EE (R² = 0,95) no corte das costelas, portanto, a equação %EE CVz = 0,9662%EE costelas + 1,5294 pode ser utilizada para estimativa da composição do CVz em EE. O mesmo ocorreu para a porcentagem de cinzas, sendo recomendada a equação %MM CVz = 0,5915%MM costelas + 0,7619 (R² = 0,88). A composição química percentual em água, EE e minerais no corte das 9-10-11ª costelas permitiu estimar com acuidade a composição do corpo vazio.

Isotopic composition of oxygen, carbon, and sulfur in interstitial water and cores at DSDP Leg 59 Holes

Comprehensive isotopic studies based on data from the Deep Sea Drilling Project have elucidated numerous details of the low- and high-temperature mechanisms of interaction between water and rocks of ocean crustal seismic Layers 1 and 2. These isotopic studies have also identified climatic changes during the Meso-Cenozoic history of oceans. Data on the abundance and isotopic composition of sulfur in the sedimentary layer as well as in rocks of the volcanic basement are more fragmentary than are oxygen and carbon data. In this chapter we specifically concentrate upon isotopic data related to specific features of the mechanisms of low-temperature interaction of water with sedimentary and volcanogenic rocks. The Leg 59 data provide a good opportunity for such lithologic and isotopic studies, because almost 600 meters of basalt flows and sills interbedded with tuffs and volcaniclastic breccias were cored during the drilling of Hole 448A. Moreover, rocks supposedly exposed to hydrothermal alteration play an important role at the deepest horizons of that mass. Sulfur isotopic studies of the character of possible biogenic processes of sulfate reduction in sediments are another focus, as well as the nature and origin of sulfide mineralization in Layer-2 rocks of remnant island arcs. Finally, oxygen and carbon istopic analyses of biogenic carbonates in the cores also enabled us to investigate the effects of changing climatic conditions during the Cenozoic. These results are compared with previous data from adjacent regions of the Pacific Ocean. Thus this chapter describes results of isotopic analyses of: oxygen and sulfur of interstitial water; oxygen and carbon of sedimentary carbonates and of calcite intercalations and inclusions in tuffs and volcaniclastic breccias interbedded with basalt flows; and sulfur of sulfides in these rocks.

Chloroflexus spp. and Sulfurihydrogenibium spp. in microbial mats of the Nakabusa hot spring, Japan

Microbial mats develop in a wide range of aquatic habitats, such as geothermal hot springs, hypersaline ponds, marine cold seeps or hydrothermal vents. The Nakabusa hot spring is located in the Nagano Prefecture, Japan (36.3875N, 137.75E), dense olive-green microbial mats develop in regions where the slightly alkaline, sulfidic effluent has cooled to 65°C. The microbial community of such mats was analyzed by focusing on the diversity, as well as the in situ distribution and function of bacteria involved in sulfur cycling. Microbial mat samples were kept in sterile plastic tubes (for molecular analysis) or glass bottles completely filled with hot spring water to avoid oxidation. Samples were transferred to the laboratory on ice and used for physiological experiments within 8h. Quantification of cell biovolumes was carried out based on images of mat sections hybridized with Sulfurihydrogenibium- and Chloroflexi-specific probes, and stained with DAPI. In situ hybridizations (CARD-FISH) of thin matsections showed a heterogeneous vertical distribution of Sulfurihydrogenibium and Chloroflexus. Sulfurihydrogenibium dominated near the mat surface (50% of the total mat biovolume), while Chloroflexus dominated in deeper layers (up to 64% of the total mat biovolume).

Performance, emission and combustion characteristics of an indirect injection (IDI) multi-cylinder compression ignition (CI) engine operating on neat jatropha and karanj oils preheated by jacket water

Renewable non-edible plant oils such as jatropha and karanj have potential to substitute fossil diesel fuels in CI engines. A multi-cylinder water cooled IDI type CI engine has been tested with jatropha and karanj oils and comparisons made against fossil diesel. The physical and chemical properties of the three fuels were measured to investigate the suitability of jatropha and karanj oils as fuels for CI engines. The engine cooling water circuit and fuel supply systems were modified such that hot jacket water preheated the neat plant oil prior to injection. Between jatropha and karanj there was little difference in the performance, emission and combustion results. Compared to fossil diesel, the brake specific fuel consumption on volume basis was around 3% higher for the plant oils and the brake thermal efficiency was almost similar. Jatropha and karanj operation resulted in higher CO 2 and NO x emissions by 7% and 8% respectively, as compared to diesel. The cylinder gas pressure diagram showed stable engine operation with both plant oils. At full load, the plant oils gave around 3% higher peak cylinder pressure than fossil diesel. With the plant oils, cumulative heat release was smaller at low load and almost similar at full load, compared to diesel. At full load, the plant oils exhibited 5% shorter combustion duration. The study concludes that the IDI type CI engine can be efficiently operated with neat jatropha (or karanj) oil preheated by jacket water, after small modifications of the engine cooling and fuel supply circuits. © 2012 Elsevier Ltd.

Características de carcaça de suínos de três linhagens genéticas em diferentes idades ao abate

O objetivo deste trabalho foi estudar as características da carcaça de suínos de diferentes linhagens genéticas, em diferentes idades ao abate. Foram utilizados 88 suínos por linhagem, fêmeas e machos castrados, com idade e peso médio iniciais de 74 dias e 30kg, respectivamente, pertencentes a três linhagens genéticas distintas, designadas de AgroceresPic, Dalland e Seghers. A etapa experimental foi dividida em quatro fases (Crescimento I, Crescimento II, Terminação I e Terminação II). Ao final de cada etapa, foram abatidos 60 animais (10 por linhagem/sexo), para as caracterizações: Peso (PCQ) e Rendimento de Carcaça Quente (RCQ), Área de Olho de Lombo (AOL) e Espessura de Toucinho (ET). Na análise dos resultados foi utilizado um delineamento inteiramente casualizado com desdobramento dos graus de liberdade em esquema fatorial 4 x 3 x 2, sendo quatro idades ao abate (90, 119, 150 e 186 dias), três linhagens (AgroceresPic, Dalland e Seghers) e dois sexos (fêmea e macho castrado), com 10 repetições por tratamento, sendo utilizado o pacote PROC MIXED do Softwear SAS. Os valores médios de peso vivo apresentaram diferença entre as linhagens e interação entre fase e linhagem (P<0,05). Os valores médios das demais variáveis estudadas apresentaram diferença e a interação (P<0,05) entre fase, linhagem e sexo, sendo que de maneira geral as principais diferenças ocorreram a partir da fase de Terminação I, em que as fêmeas das linhagens AgroceresPic e Dalland apresentaram melhores resultados (P<0,05) de RCQ (80,4 e 80,7%, respectivamente) em comparação com os machos (78,8 e 78,7%, respectivamente) e além disso as fêmeas Dalland apresentaram valores superiores (P<0,01) de AOL e ET (45,7cm² e 11,4mm x 38,3cm² e 18,3mm). Conclui-se que as linhagens genéticas avaliadas apresentaram características de carcaça muito interessantes para o mercado atual e que as fêmeas suínas podem ser utilizadas em programas que visem o abate de animais mais pesados.

Effect of lipopolysaccharide from periodontal pathogens on the production of tissue plasminogen activator and plasminogen activator inhibitor 2 by human gingival fibroblasts

Both tissue plasminogen activator (t-PA) and plasminogen activator inhibitor 2 (PAI-2) are important proteolysis factors present in inflamed human periodontal tissues. The aim of the present study was to investigate the effect of lipopolysaccharide (LPS) on the synthesis: of t-PA and PAI-2 by human gingival fibroblasts (HGF). LPS from different periodontal pathogens including Actinobacillus actinomycetemcomitans, Porphyromonas gingivalis and Fusobacterium nucleatum were extracted by the hot phenol water method. The levels of t-PA and PAI-2 secreted into the cell culture media were measured by enzyme-linked immunosorbent assays (ELISA). The mRNA for t-PA and PAI-2 were measured by RT-PCR. The results showed t-PA synthesis was increased in response to all types of LPS studied and PAI-2 level was increased by LPS from A. actinomycetemcomitans and F. nucleatum, but not P. gingivalis. When comparing the effects of LPS from non-periodontal bacteria (Escherichia coli and Salmonella enteritidis) with the LPS from periodontal pathogens, we found that the ratio of t-PA to PAI-2 was greater following exposure of the cells to LPS from periodontal pathogens. The highest ratio of t-PA to PAI-2 was found in those cells exposed to LPS from P. gingivalis. These results indicate that LPS derived from periodontal pathogens may cause unbalanced regulation of plasminogen activator and plasminogen activator inhibitor by HGF and such an effect may, in part, contribute to the destruction of periodontal connective tissue through dysregulated pericellular proteolysis.

Execução de um projecto solar térmico para uma instalação de A.Q.S. da Escola Básica Guilherme Stephens

O presente documento tem como principal objectivo efectuar o projecto de dimensionamento de um sistema de águas quentes sanitárias para uma escola. Numa primeira fase foi elaborado uma pesquisa sobre o contexto energético, a nível mundial, europeu e nacional, bem como o seu contexto jurídico a nível europeu e nacional, e uma explicação superficial sobre os fundamentos da energia solar, onde se foca a importância da radiação solar e os vários tipos de sistemas solares térmicos, bem como os seus constituintes. Segue-se a abordagem ao caso de estudo onde foram efectuados inicialmente inquéritos como forma de determinar os consumos de água quente utilizada nessa escola. Continuou-se o estudo efectuando-se a variação de duas características do sistema solar: o tamanho dos depósitos e o tipo de colectores solares a aplicar. Após as simulações efectuadas para a determinação das soluções a aplicar ao sistemasolar e apresentadas ao longo do presente documento, foram efectuadas análises económicas como forma de se verificar a viabilidade do sistema a aplicar. Por último foram elaboradas conclusões sobre o sistema a aplicar e apresentados alguns cenários financeiros do mesmo.

Kuormituksen vaikutus kromatografiseen erotukseen alikriittisellä vedellä

Teollisessa kromatografiassa kolonnia pyritään kuormittamaan mahdollisimman paljon, jotta saataisiin maksimoitua erotetun komponentin määrä aikayksikköä kohden. Tässä työssä kuormitusta tutkittiin nostamalla syöttöliuoksen, synteettisen melassin, näyteväkevyyttä 80-125 ºC:ssa. Eluenttina oli paineistettu kuumaa vesi ja hartsina vahva Na-muotoinen PS-DVB pohjainen vahva kationinvaihtohartsi. Lämpötilaa nostamalla piikit kapenivat ja tulivat symmetrisemmiksi, erotus nopeutui sekä suola erottui usein paremmin sokereista. Syöttöliuoksen kuiva-ainetta lisättiin asteittain 55 p-% saakka, jolloin ei vielä havaittu ongelmia erotuksessa. Lämpötilassa 125 ºC havaittiin erotuksen aikana kuormituksesta riippumatonta sakkaroosin invertoitumista. Vertailtaessa eri stationäärifaaseja havaittiin Na-muotoisen PS-DVB pohjaisen kationinvaihtohartsin erottavan yleensä sokereita, sokerialkoholeja, oligosakkarideja ja betaiinia lähes poikkeuksetta paremmin alhaisilla pitoisuuksilla kuin neutraalihartsi ja Na-muotoinen zeoliitti. Erottuminen ei yleensä parantunut lämpötilaa nostamalla, mutta piikit kapenivat ja erotus nopeutui. Monosakkaridien erotus huononi 125 ºC:ssa kationinvaihtohartsilla. Tutkittaessa terveysvaikutteisten ksylo-oligosakkaridien soveltuvuutta alikriittiseen erotukseen, niiden havaittiin huomattavasti hydrolysoituvan happamissa olosuhteissa koeputkessa 100 ºC:ssa kahdessa tunnissa. Näytteessä olevien epäpuhtauksien havaittiin katalysoineen hydrolyysiä. Hydrolysoituminen oli hitaampaa neutraaleissa olosuhteissa korotetussa lämpötilassa. Tästä voitiin tehdä johtopäätös, että alikriittiset olosuhteet eivät sovi ksylo-oligosakkaridien erotukseen.

Use of lipopolysaccharides to characterize Bradyrhizobium spp.

Three methods of extraction of lipopolysaccharide (LPS) were compared-the conventional hot phenol-water method with 40% phenol, a modified form of this method using 10% phenol, and the hot saline method. Good recovery of LPS was achieved by each of the three methods, with the LPS found in the aqueous phase with the two phenol-based procedures. The application of SDS-PAGE to the LPS extracts, followed by silver staining, showed similar banding with all three methods of extraction. When the hot saline extraction LPS fraction from eight strains of Bradyrhizobium spp. and eight strains of Bradyrhizobium japonicum was compared with SDS-PAGE, characteristic profiles were achieved. Serological analysis of eight strains of Bradyrhizobium spp., using antisera prepared against whole cells in agglutination reactions, showed extensive sharing of antigens. When antisera was prepared using outer membrane LPS, extracted by the hot saline method, the amount of cross-reaction was reduced greatly. The results indicated that LPS provide an efficient means of obtaining monospecific antisera to be used for serological identification of strains of Bradyrhizobium spp. and that the hot saline extraction method is recommended for a fast, simple and efficient way to obtain LPS and characterize this bacterium.

Mushroom-derived preparations in the prevention of H2O2-induced oxidative damage to cellular DNA

Aqueous extracts of the sporophores of eight mushroom species were assessed for their ability to prevent H2O2-induced oxidative damage to cellular DNA using the single-cell gel electrophoresis (Comet) assay. The highest genoprotective effects were obtained with cold (20°C) and hot (100°C) water extracts of Agaricus bisporus and Ganoderma lucidum fruit bodies, respectively. No protective effects were observed with Mushroom Derived Preparations (MDPs) from Flammulina velutipes, Auricularia auricula, Hypsizygus marmoreus, Lentinula edodes, Pleurotus sajor-caju, and Volvariella volvacea. These findings indicate that some edible mushrooms represent a valuable source of biologically active compounds with potential for protecting cellular DNA from oxidative damage. © 2002 Wiley-Liss, Inc.

Associação genética entre características da carcaça e carne com características de crescimento em bovinos Nelore

Pós-graduação em Genética e Melhoramento Animal - FCAV