Studies On Friction And Formation Of Transfer Layer In Hcp Metals

Surface texture plays an important role in the frictional behavior and transfer layer formation of contacting surfaces. In the present investigation, basic experiments were conducted using an inclined pin-on-plate sliding apparatus to better understand the role of surface texture on the coefficient of friction and the formation of a transfer layer. In the experiments, soft HCP materials such as pure Mg and pure Zn were used for the pins and a hardened 080 M40 steel was used for the plate. Two surface parameters of the steel plates—roughness and texture—were varied in tests that were conducted at a sliding speed of 2 mm/s in ambient conditions under both dry and lubricated conditions. The morphologies of the worn surfaces of the pins and the formation of the transfer layer on the counter surfaces were observed using a scanning electron microscope. In the experiments, the occurrence of stick-slip motion, the formation of a transfer layer, and the value of friction were recorded. With respect to the friction, both adhesion and plowing components were analyzed. Based on the experimental results, the effect of surface texture on the friction was attributed to differences in the amount of plowing. Both the plowing component of friction and the amplitude of stick-slip motion were determined to increase surface textures that promote plane strain conditions and decrease the textures that favor plane stress conditions.

Thickness-dependent fcc-hcp phase transformation in polycrystalline titanium thin films

Polycrystalline Ti thin films are shown to gradually transform from face-centered cubic (fcc) to hexagonal close-packed structure (hcp) with increasing film thickness. Diffraction stress analysis revealed that the fcc phase is formed in a highly compressive hcp matrix (>= 2 GPa), the magnitude of which decreases with increasing film thickness. A correlation between stress and crystallographic texture vis-a-vis the fcc-hcp phase transformation has been established. The total free energy change of the system upon phase transformation calculated using the experimental results shows that the fcc-hcp transformation is theoretically possible in the investigated film thickness regime (144-720 nm) and the hcp structure is stable for films thicker than 720 nm, whereas the fcc structure can be stabilized in Ti films much thinner than 144 nm. (C) 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Smaller is Plastic: Polymorphic Structures and Mechanism of Deformation in Nanoscale hcp Metals

Using first-principles calculations, we establish the existence of highly-stable polymorphs of hcp metals (Ti, Mg, Be, La and Y) with nanoscale structural periodicity. They arise from heterogeneous deformation of the hcp structure occurring in response to large shear stresses localized at the basal planes separated by a few nanometers. Through Landau theoretical analysis, we show that their stability derives from nonlinear coupling between strains at different length scales. Such multiscale hyperelasticity and long-period structures constitute a new mechanism of size-dependent plasticity and its enhancement in nanoscale hcp metals.

Theoretical investigation of epitaxial deformation and the hcp-bcc transition of alkali metals

The deformation of alkali metals K, Rb, and Cs under epitaxial deformation is studied via the ab initio pseudopotential plane wave method using the local-density approximation. Under loading from the stable fee phase, metastable stares along directions [001], [111], and [201] are identified. One metastable state, presented at direction [201], has a very low symmetry in contrast to the planes [001] and [201]. Our results show that the softening direction and sequences of growth is significantly affected by the existence of the metastable states and magnitude of the energy barrier. The resulting softening sequences from soft to hard are [201], [110], [001], and [111] under biaxial compression and [001], [111], [201], and [110] under biaxial tension. An orthorhombic deformation path is used to investigate the fact, that the structure of the alkali films K and Cs evolve from the quasihexagonal structure into the (110)-oriented bcc structure, observed by experiments.

Distribuição e conservação dos genes que codificam as proteínas VgrG e Hcp em espécies de Aeromonas

Aeromonas spp. são bastonetes Gram negativos amplamente distribuídos nos ambientes aquáticos, com relatos de isolamento em água de abastecimento público e alimentos. Este micro-organismo possui potencial de causar doenças intestinais e extraintestinais cuja patogenicidade está associada a sua virulência multifatorial. Diversos determinantes de virulência de Aeromonas já foram identificados, incluindo sistemas de secreção de proteínas. O sistema de secreção tipo VI (SST6) é o mais recente sistema de secreção de proteínas identificado em bactérias cuja presença em estirpes no gênero Aeromonas pode implicar atividades de citotoxicidade para o hospedeiro, pois esse sistema é capaz de injetar moléculas efetoras dentro da célula, interferindo diretamente nos processos celulares. A fim de determinar a presença e analisar a distribuição dos genes hcp e vgrG codificadores das proteínas efetoras do SST6 em Aeromonas spp. o presente estudo examinou 119 cepas isoladas de diversas origens pela técnica da PCR após o desenho de oligonucleotídeos iniciadores específicos. Objetivamos ainda analisar a variabilidade genética interespecífica dos genes hcp e vgrG a partir de dados de sequenciamento. Os resultados obtidos indicaram a distribuição dos genes vgrG e hcp em 46% das cepas de Aeromonas hydrophila e Aeromonas caviae de diferentes origens. Entre as cepas de A. hydrophila a maior frequência foi observada nas cepas isoladas de humanos, onde todas foram positivas para os iniciadores que amplificaram um produto de 541 pb do gene vgrG e 418 pb do gene hcp. Entre as cepas de A. caviae, a incidência de genes vgrG e hcp foi mais elevada nas cepas isoladas de alface (60%) e peixes (50%). As cepas analisadas de origem ambiental apresentaram índice total de 36% de positividade, apresentando frequência de 60% e 22% em A. hydrophila e A. caviae, respectivamente. Os dados obtidos da análise de cepas de origem alimentar mostraram a presença dos genes vgrG e hcp em 67% (A. hydrophila) e 60% (A. caviae) das cepas isoladas de folhas de alface. Nas cepas isoladas de queijo os genes foram encontrados em 67% e 12,5% das cepas de A. hydrophila e de A. caviae, respectivamente. O alinhamento múltiplo entre as sequências dos segmentos dos genes hcp e vgrG obtidas no sequenciamento indicou grau de identidade nucleotídica de 75 a 100% entre as sequências de hcp e 80 a 100% entre as sequências de vgrG. Em conclusão, nossos resultados indicaram que os iniciadores desenhados foram capazes de detectar suas sequências alvo em cepas de A. caviae e outras espécies de Aeromonas, sugerindo a existência de homologia entre os genes nas diferentes espécies, confirmada após sequenciamento de DNA. Os dados indicaram que esses genes estão distribuídos em várias espécies de Aeromonas e em cepas isoladas de diversas fontes. Ressaltamos a prevalência de cepas de A. hydrophila PCR-positivas em isolados clínicos, sugerindo a participação do SST6 no complexo universo da virulência multifatorial que permeia esse micro-organismo

Extended application of edge-to-edge matching model to HCP/HCP (alpha-Mg/MgZn2) system in magnesium alloys

In the present work, the edge-to-edge matching model has been introduced to predict the orientation relationships (OR) between the MgZn2 phase which has hexagonal close packed (HCP) structure and the HCP a-Mg matrix. Based on the crystal structures and lattice parameters only, the model has predicted the two most preferred ORs and they are: (1) [1 1 2 3](alpha-Mg) vertical bar vertical bar]1 1 2 3](alpha-Mg), (0 0 0 1)(alpha-Mg) 0.27 degrees from (0 0 0 1)(MgZn2), (1 0 1 1)(alpha-Mg) 26.18 degrees from (1 1 2 2)(MgZn2), (2) [1 0 1 0](alpha-Mg),vertical bar vertical bar[1 1 2 0](MgZn2), (0 0 0 1)(alpha-Mg) vertical bar vertical bar(0 0 0 1)(MgZn2), (1 0 1 1)(alpha-Mg) 3.28 degrees from ( 1 1 2 2)(MgZn2). Four experimental ORs have been reported in the alpha-Mg/MgZn2 system, and the most frequently reported one is ideally the OR (2). The other three experimental ORs are near versions of the OR (2). The habit plane of the OR (2) has been predicted and it agrees well with the experimental results.

Structure maps for hcp metals from first-principles calculations

The ability to predict the existence and crystal type of ordered structures of materials from their components is a major challenge of current materials research. Empirical methods use experimental data to construct structure maps and make predictions based on clustering of simple physical parameters. Their usefulness depends on the availability of reliable data over the entire parameter space. Recent development of high-throughput methods opens the possibility to enhance these empirical structure maps by ab initio calculations in regions of the parameter space where the experimental evidence is lacking or not well characterized. In this paper we construct enhanced maps for the binary alloys of hcp metals, where the experimental data leaves large regions of poorly characterized systems believed to be phase separating. In these enhanced maps, the clusters of noncompound-forming systems are much smaller than indicated by the empirical results alone. © 2010 The American Physical Society.

The anharmonic force field of HCN and HCP

The quadratic, cubic, and quartic force field of HCN has been calculated by a least squares refinement to fit the most recent observed data on the vibration-rotation constants of HCN, DCN and H13CN. All of the observed parameters are fitted within their standard errors of observation. The corresponding parameters for other isotopic species are calculated. For HCP and DCP the more limited data available have been fitted to an anharmonic force field using constraints based on comparison with HCN. Using this force field the zero-point rotational constants B0 have been corrected to obtain the equilibrium constants Be, and hence the equilibrium structure has been determined to be re(CH) = 1•0692(7)A, and re(CP) = 1•5398(2)A.

Influence of grain size on twinning in two hcp metals

Deformation twinning behaviour in differently grain sized samples of a commercial pure titanium and a magenisum alloy is investigated. In some aspects the phenomenology of twinning differs between the two materials while in others both materials show a similar response. Nucleation density per unit of nucleating interface and twin aspect ratio scale with applied stress. The impact of grain size on twin volume fraction is modelled analytically.

Edge-to-edge matching and its applications - Part I. Application to the simple HCP/BCC system

The edge-to-edge matching crystallographic model has been used to predict all the orientation relationships (OR) between crystals that have simple hexagonal close packed (HCP) and body-centered cubic (BCC) structures. Using the critical values for the interatomic spacing misfit along the matching directions and the cl-value mismatch between matching planes, the model predicted all the four common ORs, namely the Burgers OR, the Potter OR, the Pitsch-Schrader OR and the Rong Dunlop OR, together with the corresponding habit planes. Taking the c(H)/a(H) and a(H)/a(B) ratios as variables, where H and B denote the HCP and BCC structures respectively, the model also predicted the relationship between these variables and the four ORs. These predictions are perfectly consistent with the published experimental results. As was the case in the FCC/BCC system, the edge-to-edge matching model has been shown to be a powerful tool for predicting the crystallographic features of diffusion-controlled phase transformations. (C) 2004 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Atomistic exploration of deformation properties of copper nanowires with pre-existing defects

Based on the embedded atom method (EAM) and molecular dynamics (MD) method, in this paper, the tensile deformation properties of Cu nanowires (NWs) with different pre-existing defects, including single surface defects, surface bi-defects and single internal defects, are systematically studied. In-depth deformation mechanisms of NWs with pre-existing defects are also explored. It is found that Young's modulus is insensitive to different pre-existing defects, but yield strength shows an obvious decrease. Defects are observed influencing greatly on NWs' tensile deformation mechanisms, and playing a role of dislocation sources. Besides of the traditional deformation process dominated by the nucleation and propagation of partial dislocations, the generations of twins, grain boundaries, fivefold deformation twins, hexagonal close-packed (HCP) structure and phase transformation from face-centred cubic (FCC) structure to HCP structure have been triggered by pre-existing defects. It is found that surface defect intends to induce larger influence to yield strength than internal defect. Most importantly, the defect that lies on slip planes exerts larger influence than other defects. As expected, it is also found that the more or longer of the defect, the bigger influence will be induced.

Legal issues related to Accountable-eHealth systems in Australia

Information privacy requirements of patients and information requirements of healthcare providers (HCP) are competing concerns. Reaching a balance between these requirements have proven difficult but is crucial for the success of eHealth systems. The traditional approaches to information management have been preventive measures which either allow or deny access to information. We believe that this approach is inappropriate for a domain such as healthcare. We contend that introducing information accountability (IA) to eHealth systems can reach the aforementioned balance without the need for rigid information control. IA is a fairly new concept to computer science, hence; there are no unambiguously accepted principles as yet. But the concept delivers promising advantages to information management in a robust manner. Accountable-eHealth (AeH) systems are eHealth systems which use IA principles as the measure for privacy and information management. AeH systems face three main impediments; technological, social and ethical and legal. In this paper, we present the AeH model and focus on the legal aspects of AeH systems in Australia. We investigate current legislation available in Australia regarding health information management and identify future legal requirements if AeH systems are to be implemented in Australia.

Designing an information accountability framework for eHealth

Information privacy is a crucial aspect of eHealth. Appropriate privacy management measures are therefore essential for its success. However, traditional measures for privacy preservation such as rigid access controls (i.e., preventive measures) are not suitable to eHealth because of the specialised and information - intensive nature of healthcare itself, and the nature of the information. Healthcare professionals (HCP) require easy, unrestricted access to as much information as possible towards making well - informed decisions. On the other end of the scale however, consumers (i.e., patients) demand control over their health information and raise concerns for privacy arising from internal activities (i.e., information use by HCPs). A proper balance of these competing concerns is vital for the implementation of successful eHealth systems. Towards reaching this balance, we propose an information accountability framework (IAF) for eHealth systems.