Wideband two-port beam splitter of a binary fused-silica phase grating

The usual beam splitter of multilayer-coated film with a wideband spectrum is not easy to achieve. We describe the realization of a wideband transmission two-port beam splitter based on a binary fused-silica phase grating. To achieve high efficiency and equality in the diffracted 0th and -1st orders, the grating profile parameters are optimized using rigorous coupled-wave analysis at a wavelength of 1550 nm. Holographic recording and the inductively coupled plasma dry etching technique are used to fabricate the fused-silica beam splitter grating. The measured efficiency of (45% x 2) = 90% diffracted into the both orders can be obtained with the fabricated grating under Littrow mounting. The physical mechanism of such a wideband two-port beam splitter grating can be well explained by the modal method based on two-beam interference of the modes excited by the incident wave. With the high damage threshold, low coefficient of thermal expansion, and wideband high efficiency, the presented beam splitter etched in fused silica should be a useful optical element for a variety of practical applications. (C) 2008 Optical Society of America.

Three-port beam splitter of a binary fused-silica grating

A deep-etched polarization-independent binary fused-silica phase grating as a three-port beam splitter is designed and manufactured. The grating profile is optimized by use of the rigorous coupled-wave analysis around the 785 nm wavelength. The physical explanation of the grating is illustrated by the modal method. Simple analytical expressions of the diffraction efficiencies and modal guidelines for the three-port beam splitter grating design are given. Holographic recording technology and inductively coupled plasma etching are used to manufacture the fused-silica grating. Experimental results are in good agreement with the theoretical values. (c) 2008 Optical Society of America.

Fiber-optic components for optical communicatios and sensing

Nos últimos anos, a Optoelectrónica tem sido estabelecida como um campo de investigação capaz de conduzir a novas soluções tecnológicas. As conquistas abundantes no campo da óptica e lasers, bem como em comunicações ópticas têm sido de grande importância e desencadearam uma série de inovações. Entre o grande número de componentes ópticos existentes, os componentes baseados em fibra óptica são principalmente relevantes devido à sua simplicidade e à elevada de transporte de dados da fibra óptica. Neste trabalho foi focado um destes componentes ópticos: as redes de difracção em fibra óptica, as quais têm propriedades ópticas de processamento únicas. Esta classe de componentes ópticos é extremamente atraente para o desenvolvimento de dispositivos de comunicações ópticas e sensores. O trabalho começou com uma análise teórica aplicada a redes em fibra e foram focados os métodos de fabricação de redes em fibra mais utilizados. A inscrição de redes em fibra também foi abordado neste trabalho, onde um sistema de inscrição automatizada foi implementada para a fibra óptica de sílica, e os resultados experimentais mostraram uma boa aproximação ao estudo de simulação. Também foi desenvolvido um sistema de inscrição de redes de Bragg em fibra óptica de plástico. Foi apresentado um estudo detalhado da modulação acústico-óptica em redes em fibra óptica de sílica e de plástico. Por meio de uma análise detalhada dos modos de excitação mecânica aplicadas ao modulador acústico-óptico, destacou-se que dois modos predominantes de excitação acústica pode ser estabelecidos na fibra óptica, dependendo da frequência acústica aplicada. Através dessa caracterização, foi possível desenvolver novas aplicações para comunicações ópticas. Estudos e implementação de diferentes dispositivos baseados em redes em fibra foram realizados, usando o efeito acústico-óptico e o processo de regeneração em fibra óptica para várias aplicações tais como rápido multiplexador óptico add-drop, atraso de grupo sintonizável de redes de Bragg, redes de Bragg com descolamento de fase sintonizáveis, método para a inscrição de redes de Bragg com perfis complexos, filtro sintonizável para equalização de ganho e filtros ópticos notch ajustáveis.

Diffraction properties of ultrashort pulsed beams with arbitrary temporal profiles studied with a volume holographic grating

Using modified two- dimensional coupled- wave theory, the diffraction properties of ultrashort pulsed beams with arbitrary temporal profiles are studied with a volume holographic grating. Analytical expressions for the profiles of the transmitted and diffracted beams are obtained. It is shown that the Bragg selectivity bandwidth of the volume grating can be influenced by the geometry parameter. Numerical results are illustrated for three different temporal profiles. For different temporal profiles, the ratios of the diffraction bandwidths to input bandwidths are discussed.

Influence of Humidity on Fiber Bragg Grating Sensors

We demonstrate the influence of the relative humidity (RH) on the wavelength of fiber Bragg grating sensors (FBGS), performing tests with five FBGS at different humidity and temperature conditions. These tests were performed in a climate chamber whose RH changes according to a scheduled profile from 30% to 90%, in steps of 10%. These profiles were repeated for a wide range of temperatures from to , in steps of . Two different types of instrumentation methods have been tested, spot welding and epoxy bonding, in two different materials, steel and carbon fiber reinforced polymer (CFRP). We discuss the results for each type of sensor and instrumentation method by analyzing the linearity of the Bragg wavelength with RH and temperature.

Influence of Humidity on Fiber Bragg Grating Sensors

We demonstrate the influence of the relative humidity (RH) on the wavelength of fiber Bragg grating sensors (FBGS), performing tests with five FBGS at different humidity and temperature conditions. These tests were performed in a climate chamber whose RH changes according to a scheduled profile from 30% to 90%, in steps of 10%. These profiles were repeated for a wide range of temperatures from 10 degrees C to 70 degrees C, in steps of 10 degrees C. Two different types of instrumentation methods have been tested, spot welding and epoxy bonding, in two different materials, steel and carbon fiber reinforced polymer (CFRP). We discuss the results for each type of sensor and instrumentation method by analyzing the linearity of the Bragg wavelength with RH and temperature.

Apodised fibre Bragg grating design subject to length constraints

We investigate apodisation profiles of fibre Bragg gratings to determine key factors in filter design, using a novel apodisation technique. This highlights some practical fabrication limitations and provides important information concerning trade-offs between sidelobe suppression and bandwidth

Apodised fibre Bragg grating design subject to length constraints

We investigate apodisation profiles of fibre Bragg gratings to determine key factors in filter design, using a novel apodisation technique. This highlights some practical fabrication limitations and provides important information concerning trade-offs between sidelobe suppression and bandwidth

Evaluation of Impact of Beam Size on Fibre Bragg Grating Fabrication

Fabrication of gratings has gone a long way since the onset by Kenneth Hill in 1976. Basic fabrication techniques such as holographic and phase-mask which have distinguishing advantages (variable wavelength, and high repeatability consecutively) have since been modified in an effort to combine the advantages of both methods. These basic methods are inherently simple and have few controls, they have been combined and modified over time to enable the possibility of fabricating gratings with complex modulation index and phase profiles.

Evaluation of impact of beam size on fibre Bragg grating fabrication

Fabrication of gratings has gone a long way since the onset by Kenneth Hill in 1976. Basic fabrication techniques such as holographic and phase-mask which have distinguishing advantages (variable wavelength, and high repeatability consecutively) have since been modified in an effort to combine the advantages of both methods. These basic methods are inherently simple and have few controls, they have been combined and modified over time to enable the possibility of fabricating gratings with complex modulation index and phase profiles.

An optical fiber Bragg grating tactile sensor

Tactile sensors are needed for many emerging robotic and telepresence applications such as keyhole surgery and robot operation in unstructured environments. We have proposed and demonstrated a tactile sensor consisting of a fibre Bragg grating embedded in a polymer "finger". When the sensor is placed in contact with a surface and translated tangentially across it measurements on the changes in the reflectivity spectrum of the grating provide a measurement of the spatial distribution of forces perpendicular to the surface and thus, through the elasticity of the polymer material, to the surface roughness. Using a sensor fabricated from a Poly Siloxane polymer (Methyl Vinyl Silicone rubber) spherical cap 50 mm in diameter, 6 mm deep with an embedded 10 mm long Bragg grating we have characterised the first and second moment of the grating spectral response when scanned across triangular and semicircular periodic structures both with a modulation depth of 1 mm and a period of 2 mm. The results clearly distinguish the periodicity of the surface structure and the differences between the two different surface profiles. For the triangular structure a central wavelength modulation of 4 pm is observed and includes a fourth harmonic component, the spectral width is modulated by 25 pm. Although crude in comparison to human senses these results clearly shown the potential of such a sensor for tactile imaging and we expect that with further development in optimising both the grating and polymer "finger" properties a much increased sensitivity and spatial resolution is achievable.

Some surface profiles of a strip after plane-strain indentation by rigid bodies with serrated surfaces

This paper is concerned with the surface profiles of a strip after rigid bodies with serrated (saw-teeth) surfaces indent the strip and are subsequently removed. Plane-strain conditions are assumed. This has application in roughness transfer of final metal forming process. The effects of the semi-angle of the teeth, the depth of indentation and the friction on the contact surface on the profile are considered.