Caracterização de juntas soldadas em PAW e GTAW de chapas finas em aço maraging 300 submetidas a vários reparos

Pós-graduação em Engenharia Mecânica - FEG

Influência do aporte térmico da soldagem GTAW no balanço de fases Ferrita/Austenita do Aço Inoxidável Duplex UNS S32205

Pós-graduação em Engenharia Mecânica - FEIS

ASTM A923-Practice A application to identify intermetallic phases in a UNS S32750 superduplex welded joint

Duplex and superduplex stainless steels present superior mechanical and corrosion properties when compared to usual stainless steels. This superiority is based on chemical composition when in a balanced microstructure (approximately 50% of ferrite). During welding, changes may occur in both, the chemical composition and volume fraction of phases in the material, which may generate the presence of intermetallic phases and, as a consequence, modify the mechanical and corrosion properties of this group of stainless steels. The objective of this work is to apply ASTM A923- Practice A to verify the presence of intermetallic phases in welded joints of UNS 32750 su-perduplex stainless steel. Tubes of UNS 32750, with external diameters of 18 and 44 mm and a thickness of 1.5 mm, were welded using orbital GTAW, with filler metal 25Cr-10Ni-4Mo and a diameter of 0.8 mm. The metal-based and welded joints were characterized by optical and scanning electron microscopy. The results showed that there was no precipitation of the intermetallic phase, such as sigma phase, detected by ASTM A923, but the HAZ of the two tubes studied presented small regions with chromium nitrides, which can also change the properties of welded joins.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Repair Welding Effects on the Bending Fatigue Strength of AISI 4130 Aeronautical Steel used in a Critical to the Flight-Safety Structure

The aim of this study was to analyze the effect of successive TIG (tungsten inert gas) welding repairs on the reverse bending fatigue strength of AISI 4130 steel, which is widely used in components critical to the flight-safety. In order to simulate the abrupt maneuvers, wind bursts, motor vibration and helixes efforts, which generate cyclic bending loadings at the welded joints of a specific aircraft component called motor cradle, experimental reverse bending fatigue tests were carried out on specimens made from hot-rolled steel plate, 1.10 mm (0.043 in) thick, by mean of a SCHENK PWS equipment, with load ratio R = -1, under constant amplitude, at 30 Hz frequency and room temperature. It was observed that the bending fatigue strength decreases after the TIG (Tungsten Inert Gas) welding process application on AISI 4130 steel, with subsequent decrease due to re-welding sequence as well. Microstructural analyses and microhardness measurements on the base material, heat-affected zone (HAZ) and weld metal, as well as the effects of the weld bead geometry on the obtained results, have complemented this study.

Effects of several TIG weld repairs on the axial fatigue strength of AISI 4130 aeronautical steel-welded joints

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Parameter optimization of AC rectangular wave outputs for aluminum cold wire GTAW

The objective of this work was to optimize the parameter setup for GTAW of aluminum using an AC rectangular wave output and continuous feeding. A series of welds was carried-out in an industrial joint, with variation of the negative and positive current amplitude, the negative and positive duration time, the travel speed and the feeding speed. Another series was carried out to investigate the isolate effect of the negative duration time and travel speed. Bead geometry aspects were assessed, such as reinforcement, penetration, incomplete fusion and joint wall bridging. The results showed that currents at both polarities are remarkably more significant than the respective duration times. It was also shown that there is a straight relationship between welding speed and feeding speed and this relationship must be followed for obtaining sound beads. A very short positive duration time is enough for arc stability achievement and when the negative duration time is longer than 5 ms its effect on geometry appears. The possibility of optimizing the parameter selection, despite the high inter-correlation amongst them, was demonstrate through a computer program. An approach to reduce the number of variables in this process is also presented.

A quality and cost approach for welding process selection

The aim of this work was to propose, apply and evaluate a methodical approach to select welding processes in a productive environment based on market requirements of Quality and Costs. A case study was used. The welds were carried out in laboratory, simulating the joint conditions of a manufacturer and using several welding processes: SMAW, GTAW, pulsed GTAW, GMAW with CO2 and Ar based shielding gases and pulsed GMAW. For Quality analysis geometrical aspects of the beads were considered and for Cost analysis, welding parameters and consumable prices. Quantitative indices were proposed and evaluated. After that, evaluation of both Quality and Costs was done, showing to be possible to select the most suitable welding process to a specific application, taking into account the market conditions of a company.

Modelización de procesos de soldadura (GMAW y GTAW) de la aleación de magnesio AZ31B. Estudio y análisis del comportamiento de este tipo de uniones soldadas frente a la corrosión en medios salinos

El magnesio y sus aleaciones representan un interesante campo de investigación dentro de la ingeniería de materiales debido a los retos que plantean tanto su conformabilidad como durabilidad. Las características físicas y mecánicas del magnesio y sus aleaciones los convierten en materiales de gran interés desde el punto de vista industrial al tratarse de uno de los materiales más abundantes y ligeros en un mundo en el que día a día los recursos y materias primas son más escasos por lo que el acceso a materiales abundantes y ligeros que permitan economizar el uso de energía cobrará mayor importancia en el futuro. En la coyuntura actual es por tanto necesario revisar procesos y procedimientos, investigando y tratando de ampliar desde este punto de vista si es posible mejorar los procedimientos de fabricación de los materiales disponibles actualmente o el desarrollo de nuevos, mejores que los anteriores, que permitan ayudar a la sostenibilidad del planeta. El magnesio, pese a ser un material muy abundante y relativamente barato, presenta una serie de inconvenientes que limitan de manera muy seria su aplicación industrial, su alta reactividad en presencia de oxígeno y su mal comportamiento frente a la corrosión así como limitaciones en su conformabilidad han estado limitando su uso y aplicaciones, los investigaciones dentro del campo de la metalurgia física de este material y el desarrollo de nuevas aleaciones han permitido su empleo en múltiples aplicaciones dentro de la industria aeroespacial, militar, automovilística, electrónica, deportiva y médica. La motivación para esta tesis doctoral ha sido tratar de aportar más luz sobre el comportamiento de una de las aleaciones comerciales base magnesio más empleadas, la AZ31B, tratando de modelizar como le afectan los procesos de soldadura y estudiando desde un punto de vista experimental como se ve modificada su microestructura, su comportamiento mecánico y su resistencia frente a la corrosión. Aunque en un principio se pensó en el empleo de métodos electroquímicos para el estudio de la corrosión de estos materiales, rápidamente se decidió prescindir de su uso dada la dificultad observada tanto durante los trabajos de investigación de esta Tesis como los encontrados por otros investigadores. Mediante microdurezas se han caracterizado mecánicamente las soldaduras de aleación de magnesio tipo AZ31 en función de diferentes materiales de aporte, observándose que el empleo de las aleaciones con mayor contenido de aluminio y zinc no contribuye a una mejora significativa de las propiedades mecánicas. Se han podido establecer correlaciones entre los modelos de simulación desarrollados y las microestructuras resultantes de los procesos reales de soldadura que permiten definir a priori que estructuras se van a obtener. De igual forma ha sido posible completar un estudio micrográfico y químico completo de las diferentes fases y microconstituyentes originados durante los procesos de soldadura, gracias a estos resultados se ha propuesto como hipótesis una explicación que justifica el comportamiento frente a la corrosión de estas aleaciones una vez soldadas. Los ensayos de corrosión realizados han permitido determinar correlaciones matemáticas que indican las velocidades de corrosión esperables de este tipo de aleaciones. Desde el punto de vista del diseño, los resultados obtenidos en este trabajo permitirán a otros investigadores y diseñadores tomar decisiones a la hora de decidir qué materiales de aporte emplear junto con las implicaciones que conllevan desde el punto de vista metalúrgico, mecánico o corrosivo las diferentes alternativas. Por último indicar que gracias al trabajo desarrollado se han definido modelos matemáticos para predecir el comportamiento frente a la corrosión de estas aleaciones, se han determinado las posibles causas y mecanismos por las que se gobierna la corrosión en la soldadura de chapas de aleación AZ31B y los motivos por los que se debe considerar el empleo de un material de aporte u otro. Los modelos de simulación desarrollados también han ayudado a comprender mejor la microestructura resultante de los procesos de soldadura y se han determinado que fases y microconstituyentes están presentes en las soldaduras de estas aleaciones. ABSTRACT Magnesium and its alloys represent and interesting research field in the material science due to the challenges of their fabrication and durability. The physical and mechanical properties of magnesium and its alloys make them a very interesting materials from and industrial point of view being one of the most abundant and lightest materials in a world in which day by day the lacking of resources and raw materials is more important, the use of light materials which allow to save energy will become more important in a near future. So that it is necessary to review processes and procedures, investigating and trying to improve current fabrication procedures and developing new ones, better than the former ones, in order to help with the sustainability of the planet. Although magnesium is a very common and relatively cheap material, it shows some inconveniences which limit in a major way their industrial application; its high reactivity in presence of oxygen, its poor corrosion resistance and some manufacturing problems had been limiting their use and applications, metallurgical investigations about this material and the development of new alloys have allowed its use in multiple applications in the aerospacial, military, automobile, electronics, sports and medical industry. The motivation for this thesis has been trying to clarify the behavior of one most used commercial base magnesium alloys, the AZ31, trying to modeling how its affected by thermal cycles of the welding process and studying from an experimental point of view how its microstructure is modified and how these modifications affect its mechanical behavior and corrosion resistance. Although at the beginning of this works it was though about the using of electrochemical techniques to evaluate the corrosion of these materials, rapidly it was decided not to use them because of the difficulty observed by during this research and by other investigators. The results obtained in this thesis have allowed to characterize mechanically AZ31 magnesium welding alloys considering different filler metals, according to this study using filler metals with a high content of aluminum and zinc does not represent an important improve It has been possible to establish correlations between simulation models and the resultant microstructures of the real melting processes originated during welding processes which allow to predict the structures which will be obtained after the welding. In addition to that it is possible to complete a complete micrographic and chemical analysis of the different phases and microconstituents created during welding, due to these results and hypothesis to explain the corrosion behavior of these welded alloys. Corrosion tests carried out have allowed defining mathematical correlations to predict corrosion rates of this kind of alloys. From a designing point of view, the results obtained in this work will let other investigators and designers to make decisions taking into account which implications have the different options from a metallurgical, mechanic and corrosive point of view. Finally we would like to indicate that thanks to this work it has been possible to define mathematical models to predict the corrosion behavior, the causes and the mechanism of this corrosion in the AZ31 welding sheets have been also determined and the reasons for using of one filler metal or another, the developed simulation models have also help to get a better understanding of the result microstructure determining the phases and the microconstituents present in the welding of this alloys.

[meanings Of The Sickening Process For Patients With Systemic Lupus Erythematosus: A Review Of The Literature.]

Systemic lupus erythematosus is an autoimmune disease that causes many psychological repercussions that have been studied through qualitative research. These are considered relevant, since they reveal the amplitude experienced by patients. Given this importance, this study aims to map the qualitative production in this theme, derived from studies of experiences of adult patients of both genders and that had used as a tool a semi-structured interview and/or field observations, and had made use of a sampling by a saturation criterion to determine the number of participants in each study. The survey was conducted in Pubmed, Lilacs, Psycinfo e Cochrane databases, searching productions in English and Portuguese idioms published between January 2005 and June 2012. The 19 revised papers that have dealt with patients in the acute phase of the disease showed themes that were categorized into eight topics that contemplated the experienced process at various stages, from the onset of the disease, extending through the knowledge of the diagnosis and the understanding of the manifestations of the disease, drug treatment and general care, evolution and prognosis. The collected papers also point to the difficulty of understanding, of the patients, on what consists the remission phase, revealing also that this is a clinical stage underexplored by psychological studies.

[in Process Citation].

20

O aluno com deficiência visual nas aulas de educação física : análise do processo inclusivo = The student with visual impairments : analysis of inclusive process

Universidade Estadual de Campinas . Faculdade de Educação Física

Hegemonia e contra-hegemonia na construção de políticas de esporte e lazer : a experiência do Consórcio Brasília = Hegemony and counter-hegemony in the process of sport and leisure policy-making : the experience of the Consortium Brasilia

Universidade Estadual de Campinas . Faculdade de Educação Física

Effects of the condylar process fracture on facial symmetry in rats submitted to protein undernutrition

PURPOSE: To investigate the facial symmetry of rats submitted to experimental mandibular condyle fracture and with protein undernutrition (8% of protein) by means of cephalometric measurements. METHODS: Forty-five adult Wistar rats were distributed in three groups: fracture group, submitted to condylar fracture with no changes in diet; undernourished fracture group, submitted to hypoproteic diet and condylar fracture; undernourished group, kept until the end of experiment, without condylar fracture. Displaced fractures of the right condyle were induced under general anesthesia. The specimens were submitted to axial radiographic incidence, and cephalometric mensurations were made using a computer system. The values obtained were subjected to statistical analyses among the groups and between the sides in each group. RESULTS: There was significative decrease of the values of serum proteins and albumin in the undernourished fracture group. There was deviation of the median line of the mandible relative to the median line of the maxilla, significative to undernutrition fracture group, as well as asymmetry of the maxilla and mandible, in special in the final period of experiment. CONCLUSION: The mandibular condyle fracture in rats with proteic undernutrition induced an asymmetry of the mandible, also leading to consequences in the maxilla.

Influence of specimens' design and manufacturing process on microtensile bond strength to enamel: laboratory and FEA comparison

This study evaluated the effect of specimens' design and manufacturing process on microtensile bond strength, internal stress distributions (Finite Element Analysis - FEA) and specimens' integrity by means of Scanning Electron Microscopy (SEM) and Laser Scanning Confocal Microscopy (LCM). Excite was applied to flat enamel surface and a resin composite build-ups were made incrementally with 1-mm increments of Tetric Ceram. Teeth were cut using a diamond disc or a diamond wire, obtaining 0.8 mm² stick-shaped specimens, or were shaped with a Micro Specimen Former, obtaining dumbbell-shaped specimens (n = 10). Samples were randomly selected for SEM and LCM analysis. Remaining samples underwent microtensile test, and results were analyzed with ANOVA and Tukey test. FEA dumbbell-shaped model resulted in a more homogeneous stress distribution. Nonetheless, they failed under lower bond strengths (21.83 ± 5.44 MPa)c than stick-shaped specimens (sectioned with wire: 42.93 ± 4.77 MPaª; sectioned with disc: 36.62 ± 3.63 MPa b), due to geometric irregularities related to manufacturing process, as noted in microscopic analyzes. It could be concluded that stick-shaped, nontrimmed specimens, sectioned with diamond wire, are preferred for enamel specimens as they can be prepared in a less destructive, easier, and more precise way.