Performance analysis of FIR digital filter design: RNS versus traditional

Residue Number System (RNS) based Finite Impulse Response (FIR) digital filters and traditional FIR filters. This research is motivated by the importance of an efficient filter implementation for digital signal processing. The comparison is done in terms of speed and area requirement for various filter specifications. RNS based FIR filters operate more than three times faster and consumes only about 60% of the area than traditional filter when number of filter taps is more than 32. The area for RNS filter is increasing at a lesser rate than that for traditional resulting in lower power consumption. RNS is a nonweighted number system without carry propogation between different residue digits.This enables simultaneous parallel processing on all the digits resulting in high speed addition and multiplication in the RNS domain

Novel window functions for digital filters

Window technique is one of the simplest methods to design Finite Impulse Response (FIR) filters. It uses special functions to truncate an infinite sequence to a finite one. In this paper, we propose window techniques based on integer sequences. The striking feature of the proposed work is that it overcomes all the problems posed by floating point numbers and inaccuracy, as the sequences are made of only integers. Some of these integer window sequences, yield sharp transition, while some of them result in zero ripple in passband and stopband.

Use of finite wordlength FIR digital filter structures with improved magnitude and phase characteristics for reduction of muscle noise in EEG signals

One of the main disturbances in EEG signals is EMG artefacts generated by muscle movements. In the paper, the use of a linear phase FIR digital low-pass filter with finite wordlength precision coefficients is proposed, designed using the compensation procedure, to minimise EMG artefacts in contaminated EEG signals. To make the filtering more effective, different structures are used, i.e. cascading, twicing and sharpening (apart from simple low-pass filtering) of the designed FIR filter Modifications are proposed to twicing and sharpening structures to regain the linear phase characteristics that are lost in conventional twicing and sharpening operations. The efficacy of all these transformed filters in minimising EMG artefacts is studied, using SNR improvements as a performance measure for simulated signals. Time plots of the signals are also compared. Studies show that the modified sharpening structure is superior in performance to all other proposed methods. These algorithms have also been applied to real or recorded EMG-contaminated EEG signal. Comparison of time plots, and also the output SNR, show that the proposed modified sharpened structure works better in minimising EMG artefacts compared with other methods considered.

Systematic methodology for the design of high performance recursive digital filters

A systematic design methodology is described for the rapid derivation of VLSI architectures for implementing high performance recursive digital filters, particularly ones based on most significant digit (msd) first arithmetic. The method has been derived by undertaking theoretical investigations of msd first multiply-accumulate algorithms and by deriving important relationships governing the dependencies between circuit latency, levels of pipe-lining and the range and number representations of filter operands. The techniques described are general and can be applied to both bit parallel and bit serial circuits, including those based on on-line arithmetic. The method is illustrated by applying it to the design of a number of highly pipelined bit parallel IIR and wave digital filter circuits. It is shown that established architectures, which were previously designed using heuristic techniques, can be derived directly from the equations described.

Hydrograph separation and development of empirical relationships using single-parameter digital filters

A reliable hydrograph separation method is necessary for surface runoff modeling and hydrological studies. This paper investigates and compares the separation characteristics of two single-parameter digital filters, which are herein referred to as the one-parameter algorithm and the conceptual method. The application of the one-parameter algorithm was found to be restricted to low and medium baseflow separations, with a maximum separation limit of 50% of the total runoff hydrograph. The one-parameter algorithm was also observed to produce unrealistic sharp peaks under the peaks of the measured hydrograph when recession constant is smaller than 0.96. On the other hand, the conceptual method is applicable even for catchments fed largely by groundwater discharge. However, a reliable estimation of recession constant is a prerequisite for applying the conceptual method for large baseflow separations. Based on the hydrograph separation results, useful empirical relationships were developed for a partially urbanized watershed to estimate total runoff and direct runoff from the measured rainfall depth. The relationships between rainfall depth and total runoff depth and rainfall depth and direct runoff depth were found to be well represented by linear equations. The empirical relationships were then applied to estimate the long-term contribution of baseflow and surface runoff to total runoff at the study site. Baseflow was found to contribute about 58–61% of the annual total runoff.

Digital filtering of oscillations intrinsic to transmission line modeling based on lumped parameters

A correction procedure based on digital signal processing theory is proposed to smooth the numeric oscillations in electromagnetic transient simulation results from transmission line modeling based on an equivalent representation by lumped parameters. The proposed improvement to this well-known line representation is carried out with an Finite Impulse Response (FIR) digital filter used to exclude the high-frequency components associated with the spurious numeric oscillations. To prove the efficacy of this correction method, a well-established frequency-dependent line representation using state equations is modeled with an FIR filter included in the model. The results obtained from the state-space model with and without the FIR filtering are compared with the results simulated by a line model based on distributed parameters and inverse transforms. Finally, the line model integrated with the FIR filtering is also tested and validated based on simulations that include nonlinear and time-variable elements. © 2012 Elsevier Ltd. All rights reserved.