Optimal and robust modal control of a flexible structure using an active dynamic vibration absorber

This paper is concerned with feedback vibration control of a lightly damped flexible structure that has a large number of well-separated modes. A single active electrical dynamic absorber is used to reduce a particular single vibration mode selectively or multiple modes simultaneously. The absorber is realized electrically by feeding back the structural acceleration at one position to a collocated piezoceramic patch actuator via a controller consisting of one or several second order lowpass filters. A simple analytical method is presented to design a modal control filter that is optimal in that it maximally flattens the mobility frequency response of the target mode, as well as robust in that it works within a prescribed maximum control spillover of 2 dB at all frequencies. Experiments are conducted with a free-free beam to demonstrate its ability to control any single mode optimally and robustly. It is also shown that an active absorber with multiple such filters can effectively control multiple modes simultaneously.

The non-ideal problem behavior using a dynamic vibration absorber with nonlinear essential stiffness and timedependent damping properties

The purpose of this study is to develop a dynamic vibration absorber using viscoelastic material with nonlinear essential stiffness and time-dependent damping properties for a non-ideal vibrating system with Sommerfeld effect, resonance capture, and jump phenomenon. The absorber is a mass-bar subsystem that consists of a viscoelastic bar with memory attached to mass, in which the internal dissipative forces depend on current, deformations, and its operational frequency varies with limited temperature. The non-ideal vibrating system consists of a linear (nonlinear) oscillator (plane frame structure) under excitation, via spring connector, of a DC-motor with limited power supply. A viscoelastic dynamic absorber modeled with elastic stiffness essentially nonlinearities was developed to further reduce the Sommerfeld effect and the response of the structure. The numerical results show the performance of the absorber on the non-ideal system response through the resonance curves, time histories, and Poincarésections. Furthermore, the structure responses using the viscoelastic damper with and without memory were studied. © IMechE 2012.

Robust broadband vibration control of a flexible structure using an electrical dynamic absorber

This paper presents a simple but practical feedback control method to suppress the vibration of a flexible structure in the frequency range between 10 Hz and 1 kHz. A dynamic vibration absorber is designed for this, which has a natural frequency of 100 Hz and a normalized bandwidth (twice the damping ratio) of 9.9. The absorber is realized electrically by feeding back the structural acceleration at one position on the host structure to a collocated piezoceramic patch actuator via an analog controller consisting of a second-order lowpass filter. This absorber is equivalent to a single degree-of-freedom mechanical oscillator consisting of a serially connected mass-spring-damper system. A first-order lowpass filter is additionally used to improve stability at very high frequencies. Experiments were conducted on a free-free beam embedded with a piezoceramic patch actuator and an accelerometer at its center. It is demonstrated that the single absorber can simultaneously suppress multiple vibration modes within the control bandwidth. It is further shown that the control system is robust to slight changes in the plant. The method described can be applied to many other practical structures, after retuning the absorber parameters for the structure under control.

A simple method for choosing the parameters of a two degree-of-freedom tuned vibration absorber

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Demonstration of non-collocated vibration control of a flexible manipulator using electrical dynamic absorbers

This paper describes an experimental study into the vibration control of a servo system comprising a servo motor and a flexible manipulator. Two modes of the system are controlled by using the servo motor and an accelerometer attached to the tip of the flexible manipulator. The control system is thus non-collocated. It consists of two electrical dynamic absorbers, each of which consists of a modal filter and, in case of an out-of-phase mode, a phase inverter. The experimental results show that each absorber acts as a mechanical dynamic vibration absorber attached to each mode and significantly reduces the settling time for the system response to a step input.

Using passive techniques for vibration damping in mechanical systems

This paper examines two passive techniques for vibration reduction in mechanical systems: the first one is based on dynamic vibration absorbers (DVAs) and the second uses resonant circuit shunted (RCS) piezoceramics. Genetic algorithms are used to determine the optimal design parameters with respect to performance indexes, which are associated with the dynamical behavior of the system over selected frequency bands. The calculation of the frequency response functions (FRFs) of the composite structure (primary system + DVAs) is performed through a substructure coupling technique. A modal technique is used to determine the frequency response function of the structure containing shunted piezoceramics which are bonded to the primary structure. The use of both techniques simultaneously on the same structure is investigated. The methodology developed is illustrated by numerical applications in which the primary structure is represented by simple Euler-Bernoulli beams. However, the design aspects of vibration control devices presented in this paper can be extended to more complex structures.

Designs for an adaptive tuned vibration absorber with variable shape stiffness element

An adaptive tuned vibration absorber (ATVA) with a smart variable stiffness element is capable of retuning itself in response to a time-varying excitation frequency., enabling effective vibration control over a range of frequencies. This paper discusses novel methods of achieving variable stiffness in an ATVA by changing shape, as inspired by biological paradigms. It is shown that considerable variation in the tuned frequency can be achieved by actuating a shape change, provided that this is within the limits of the actuator. A feasible design for such an ATVA is one in which the device offers low resistance to the required shape change actuation while not being restricted to low values of the effective stiffness of the vibration absorber. Three such original designs are identified: (i) A pinned-pinned arch beam with fixed profile of slight curvature and variable preload through an adjustable natural curvature; (ii) a vibration absorber with a stiffness element formed from parallel curved beams of adjustable curvature vibrating longitudinally; (iii) a vibration absorber with a variable geometry linkage as stiffness element. The experimental results from demonstrators based on two of these designs show good correlation with the theory.

Comments on a nonlinear and nonideal electromechanical damping vibration absorber, Sommerfeld effect and energy transfer

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Active vibration control using delayed resonant feedback

Delayed feedback (DF) control is a well-established technique to suppress single frequency vibration of a non-minimum phase system. Modal control is also a well-established technique to control multiple vibration modes of a minimum phase system. In this paper these techniques are combined to simultaneously suppress multiple vibration modes of a non-minimum phase system involving a small time delay. The control approach is called delayed resonant feedback (DRF) where each modal controller consists of a modal filter to extract the target mode signal from the vibration response, and a phase compensator to account for the phase delay of the mode. The methodology is first discussed using a single mode system. A multi-mode system is then studied and experimental results are presented to demonstrate the efficacy of the control approach for two modes of a beam. It is shown that the system behaves as if each mode under control has a dynamic vibration absorber attached to it, even though the actuator and the sensor are not collocated and there is a time delay in the control system. © 2013 IOP Publishing Ltd.

An investigation into the simultaneous use of a resonator as an energy harvester and a vibration absorber

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On a Nonideal (MRD) Damper-Electro-mechanical Absorber Dynamics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A note on non-linear phenomena in a non-ideal oscillator, with a snap-through truss absorber, including parameter uncertainties

This work considers the vibrating system that consists of a snap-through truss absorber coupled to an oscillator under excitation of an electric motor with an eccentricity and limited power, characterizing a non-ideal oscillator. It is aimed to use the non-linearity and quasi-zero stiffness of absorber (snap-through truss absorber) to obtain a significantly attenuation the jump phenomenon. There is also an interest to exhibit the reduction of Sommerfeld effect, to confirm the saturation phenomenon occurrence and show the power transfer in a non-linear structure, evidencing the pumping energy. As shown by simulations in this work, this absorber allows the energy pumping before and during the jump phenomenon, decreasing the higher amplitudes of considered system. Additionally, the occurrence of saturation phenomenon due use of snap-through truss absorber is verified. The analysis of parameter uncertainties was introduced. Sensitivity of system with parametric errors demonstrated a trustable system. © IMechE 2012.

Uso de absorvedores de vibrações eletromecânicos lineares e não-lineares em sistemas não-lineares e não-ideais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de programa em linguagem Matlab® para cálculo pelo método de elementos finitos

Para o projeto de qualquer estrutura existente (edifícios, pontes, veículos, máquinas, etc.) é necessário conhecer as condições de carga, geometria e comportamento de todas as suas partes, assim como respeitar as normativas em vigor nos países nos quais a estrutura será aplicada. A primeira parte de qualquer projeto nesta área passa pela fase da análise estrutural, onde são calculadas todas as interações e efeitos de cargas sobre as estruturas físicas e os seus componentes de maneira a verificar a aptidão da estrutura para o seu uso. Inicialmente parte-se de uma estrutura de geometria simplificada, pondo de parte os elementos físicos irrelevantes (elementos de fixação, revestimentos, etc.) de maneira a simplificar o cálculo de estruturas complexas e, em função dos resultados obtidos da análise estrutural, melhorar a estrutura se necessário. A análise por elementos finitos é a ferramenta principal durante esta primeira fase do projeto. E atualmente, devido às exigências do mercado, é imprescindível o suporte computorizado de maneira a agilizar esta fase do projeto. Existe para esta finalidade uma vasta gama de programas que permitem realizar tarefas que passam pelo desenho de estruturas, análise estática de cargas, análise dinâmica e vibrações, visualização do comportamento físico (deformações) em tempo real, que permitem a otimização da estrutura em análise. Porém, estes programas demostram uma certa complexidade durante a introdução dos parâmetros, levando muitas vezes a resultados errados. Assim sendo, é essencial para o projetista ter uma ferramenta fiável e simples de usar que possa ser usada para fins de projeto de estruturas e otimização. Sobre esta base nasce este projeto tese onde se elaborou um programa com interface gráfica no ambiente Matlab® para a análise de estruturas por elementos finitos, com elementos do tipo Barra e Viga, quer em 2D ou 3D. Este programa permite definir a estrutura por meio de coordenadas, introdução de forma rápida e clara, propriedades mecânicas dos elementos, condições fronteira e cargas a aplicar. Como resultados devolve ao utilizador as reações, deformações e distribuição de tensões nos elementos quer em forma tabular quer em representação gráfica sobre a estrutura em análise. Existe ainda a possibilidade de importação de dados e exportação dos resultados em ficheiros XLS e XLSX, de maneira a facilitar a gestão de informação. Foram realizados diferentes testes e análises de estruturas de forma a validar os resultados do programa e a sua integridade. Os resultados foram todos satisfatórios e convergem para os resultados de outros programas, publicados em livros, e para cálculo a mão feitos pelo autor.

State Dependent Riccati Equation (SDRE) control method applied in cancellation of a parametric resonance in a magnetically levitated body

Here, a simplified dynamical model of a magnetically levitated body is considered. The origin of an inertial Cartesian reference frame is set at the pivot point of the pendulum on the levitated body in its static equilibrium state (ie, the gap between the magnet on the base and the magnet on the body, in this state). The governing equations of motion has been derived and the characteristic feature of the strategy is the exploitation of the nonlinear effect of the inertial force associated, with the motion of a pendulum-type vibration absorber driven, by an appropriate control torque [4]. In the present paper, we analyzed the nonlinear dynamics of problem, discussed the energy transfer between the main system and the pendulum in time, and developed State Dependent Riccati Equation (SDRE) control design to reducing the unstable oscillatory movement of the magnetically levitated body to a stable fixed point. The simulations results showed the effectiveness of the (SDRE) control design. Copyright © 2011 by ASME.