Viscosity and self-diffusion coefficients of dialkyl adipates: a correlation scheme with predictive capabilities

A correlation and predictive scheme for the viscosity and self-diffusivity of liquid dialkyl adipates is presented. The scheme is based on the kinetic theory for dense hard-sphere fluids, applied to the van der Waals model of a liquid to predict the transport properties. A "universal" curve for a dimensionless viscosity of dialkyl adipates was obtained using recently published experimental viscosity and density data of compressed liquid dimethyl (DMA), dipropyl (DPA), and dibutyl (DBA) adipates. The experimental data are described by the correlation scheme with a root-mean-square deviation of +/- 0.34 %. The parameters describing the temperature dependence of the characteristic volume, V-0, and the roughness parameter, R-eta, for each adipate are well correlated with one single molecular parameter. Recently published experimental self-diffusion coefficients of the same set of liquid dialkyl adipates at atmospheric pressure were correlated using the characteristic volumes obtained from the viscosity data. The roughness factors, R-D, are well correlated with the same single molecular parameter found for viscosity. The root-mean-square deviation of the data from the correlation is less than 1.07 %. Tests are presented in order to assess the capability of the correlation scheme to estimate the viscosity of compressed liquid diethyl adipate (DEA) in a range of temperatures and pressures by comparison with literature data and of its self-diffusivity at atmospheric pressure in a range of temperatures. It is noteworthy that no data for DEA were used to build the correlation scheme. The deviations encountered between predicted and experimental data for the viscosity and self-diffusivity do not exceed 2.0 % and 2.2 %, respectively, which are commensurate with the estimated experimental measurement uncertainty, in both cases.

Síntese de β-cetoésteres cíclicos: novo procedimento para ciclizações de Dieckmann empregando ALCL3 e trietilamina

In this communication we describe a new methodology to Dieckmann cyclization of diethyl adipate (1) and diethyl pimelate (3) applying "push-pull" strategy using anhydrous aluminium trichloride and triethylamine in dichloromethane at room temperature. This method is very efficient, simple, safe and reproducible, giving the corresponding cyclic β-keto ester derivatives in 84% and 71% yield, respectively.

Singlet molecular oxygen trapping by the fluorescent probe diethyl-3,3 '-(9,10-anthracenediyl)bisacrylate synthesized by the Heck reaction

Singlet molecular oxygen O(2)((1)Delta(g)) is a potent oxidant that can react with different biomolecules, including DNA, lipids and proteins. Many polycyclic aromatic hydrocarbons have been studied as O(2)((1)Delta(g)) chemical traps. Nevertheless, a suitable modification in the polycyclic aromatic ring must be made to increase the yield of O(2)((1)Delta(g)) chemical trapping. With this goal, an anthracene derivative, diethyl-3,3 '-(9,10-anthracenediyl)bisacrylate (DADB), was obtained from the reaction of 9,10-dibromoanthracene and ethyl acrylate through the Heck coupling reaction. The coupling of ethyl acrylate with the anthracene ring produced a new lipophilic, esterified, fluorescent probe reactive toward O(2)((1)Delta(g)). This compound reacts with O(2)((1)Delta(g)) at a rate of k(r) = 1.69 x 10(6) M(-1) s(-1) forming a stable endoperoxide (DADBO(2)), which was characterized by UV-Vis, fluorescence, HPLC/MS and (1)H and (13)C NMR techniques. The photophysical, photochemical and thermostability features of DADB were also evaluated. Furthermore, this compound has the potential for great application in biological systems because it is easily synthetized in large amount and generates specific endoperoxide (DADBO(2)), which can be easily detected by HPLC tandem mass spectrometry (HPLC/MS/MS).

Particle size and concentration of poly(epsilon-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures

The objective of this study was to evaluate the effect of particle size and concentration of poly(F.-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures, comparing it with polyethylene under the same experimental conditions. Two soil types were used: a Kandiudalfic Eutrudox with a clayey texture and an Arenic Hapludult with a sandy texture. The two different plastic specimens were incorporated in the form of plastic films with three increasing particle sizes and six doses, from 0 to 2.5 mg C g(-1) soil. Each plastic dose was incorporated into 200 g of soil placed in a hermetically closed jar at 28 degrees C, and incubated for a 120-day period to determine CO(2) evolution. Once again it was confirmed that polyethylene is almost non-biodegradable, in contrast to PCL/S, which can be defined as a biodegradable material. Soil texture affected the mineralization kinetics of the plastic specimens, with higher values for the clayey soil. No changes in soil microbial biomass-C or -N were observed by adding polyethylene and PCL/S to the soil. Also, no significant differences were observed on seed emergence and development of rice seedlings (Oryza sativa L.) in plastic modified soil. (C) 2009 Elsevier Ltd. All rights reserved.

Synthesis and NMR characterization of aliphatic-aromatic copolyesters by reaction of poly(ethylene terephthalate) post-consumer and poly(ethylene adipate)

An aliphatic-aromatic copolyester of poly(ethylene terephthalate), PET, and poly(ethylene adipate), PEA, PET-co-PEA, was synthesized by the high temperature melt reaction of post-consumer PET and PEA. As observed by NMR spectroscopy, the reaction yielded random copolyesters in a few minutes through ester-interchange reactions, even without added catalyst. The copolyesters obtained in the presence of a catalyst presented higher intrinsic viscosity than that obtained without the addition of catalyst, due to simultaneous polycondensation and ester-interchange reactions. The structure of the aliphatic-aromatic copolyesters obtained in different PET/PEA ratio is random as observed by NMR analysis.

Starch/poly (butylene adipate-co-terephthalate)/montmorillonite films produced by blow extrusion

This study aims to prepare biodegradable films from cassava starch, poly (butylene adipate-co-terephthalate) (PBAT), and montmorillonite (MMT) using blow-extrusion process and analyze the effects of different types and concentrations of MMT on the microstructure, physicochemical, and mechanical properties of the resulting films. The films were produced by blending 30% of PBAT with glycerol (17.5%), starch (49.0-52.5%), and four different types of montmorillonite (Cloisite® Na+, 10A, 15A, and 30B) at two different concentrations (1.75% and 3.5%). All the films prepared in this study showed an increase in the basal spacing of MMT layers. In particular, the films with 10A and 30B showed the highest increase in intercalation basal spacing, suggesting the formation of intercalated composites. The addition of nanoclays decreased the elongation of films. The addition of Cloisite® 10A resulted in films with the lowest WVP values and the highest stability to water adsorption under different RH conditions.

Mefenpyr-diethyl action on fenoxaprop-p-ethyl detoxification in wheat varieties

Safeners protect crops against herbicide injury. The aim of this study was to examine the differential susceptibility of five wheat (Triticum aestivum) varieties to the herbicide fenoxaprop-p-ethyl, as well as the performance of mefenpyr-diethyl on minimizing herbicide injury and on lipid contents. Varieties BRS 49, CD 104, CEP 24, IAPAR 78 and Rubi were sprayed with fenoxaprop-p-ethyl (69 g ha¹), fenoxaprop-p-ethyl + mefenpyr-diethyl (69 g + 18.75 g ha-1), or mefenpyr-diethyl (18.75 g ha-1). Plants were evaluated visually for injury at 7 and 14 days after treatment (DAT). Glutathione S-transferase (GST) activity was assayed in aerial parts at 7 DAT, and lipid content was measured at 14 DAT. Varieties CEP 24, IAPAR 78 and Rubi were more tolerant to fenoxaprop-p-ethyl than BRS 49, and CD 104 rapidly recovering from the slight phytotoxicity symptoms produced by the herbicide. Mefenpyr-diethyl prevented crop injury associated with the herbicide. GST activity did not correlate directly with fenoxaprop-p-ethyl detoxification. However, lipid content was related to the susceptibility of wheat to fenoxaprop-p-ethyl treatment.

Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Optical and Thermal Properties of Diethyl-(2R, 3R) (1)-tartrate Based Chiral Polyurethanes with Main Chain Amido Chromophores

The toluene diisocyanate based optically active chiral polyurethanes were synthesized according to the symmetry conditions. The noncentrosymmetric (both charge asymmetry and spatial asymmetry) environment were attained by the incorporation of the chiral units (diethyl-(2R,3R)(þ)-tartrate) and donor-acceptor building blocks in the main chain which induce a helical conformation in the macromolecular chain. A series of optically active polyurethanes containing chiral linkages in the polymer back bone have been synthesized by using DBTDL catalyst by incorporating the amido diols which were obtained by the aminolysis of e-caprolactone by using the diamines, diaminoethane, diaminobutane, and diaminohexane respectively. The effect of incorporation of the chiral molecule diethyl-(2R,3R)(þ)-tartrate on the properties of polyurethanes was studied by changing the chromophores and also by varying the chiral-chromophore composition. Various properties of polyurethanes were investigated by UV, Fluorescence, TG/DTA, XRD, polarimetric techniques, Kurtz-Perry powder techniques, etc.

6,6 '-bis-(5,6-diethyl-[1,2,4]triazin-3-yl)-2,2 '-bipyridyl the first example of a new class of quadridentate hetercyclic extraction reagents for the separation of americium(III) and europium(III)

The synthesis of the first example of a new class of tetradentate reagents for the efficient separation of americium(Ill) and europium(111) is reported together with the structure of the complex formed with europium(III), (C) 2004 Elsevier B.V. All rights reserved.

Synthesis, characterization and adsorption properties of porous mixed valent diruthenium(II,III)-terephthalate and diruthenium(II,III)-adipate polymers

Two porous mixed valent diruthenium(II,III)-dicarboxylate compounds have been prepared and characterized by spectroscopic methods, X-ray diffraction and thermogravimetry. Crystalline solids of [Ru(2)(tere)(2)Cl] center dot 3.5H(2)O (tere=terephthalate) and [Ru(2)(adip)(2)Cl] center dot 1.5H(2)O (adip=adipate) consist of extended chains in which polymeric layers of multiply metal-metal bonded [Ru(2)](5+) cores are bridged by dicarboxylate ligands in paddlewheel type geometries. Units of [Ru(2)(dicarboxylate)(2)](n)(+) are linked by axial bridging chloride ions generating three-dimensional networks. The polymers loose non-bonded water molecules at low temperatures but do not undergo thermal decomposition below 280-300 degrees C. Both of compounds exhibit high BET surface areas, [Ru(2)(tere)(2)Cl]: 235 m(2) g(-1) and [Ru(2)(adip)(2)Cl]: 281 m(2) g(-1), and occlude similar numbers of mol of N(2) per mol of metal. The terephthalate ligand generated an organized structure with supermicropores (total pore size of 0.24 cm(3) g(-1)) while the adipate ligand led to a mesoporous structure (total pore sizes of 0.47 cm(3) g(-1)) for the corresponding diruthenium(II,III)-dicarboxylate polymers. (c) 2008 Elsevier B.V. All rights reserved.

Spectroscopic and theoretical studies of some N,N-diethyl-2-[(4 `-substituted)phenylsulfonyl]acetamides

The analysis of the IR carbonyl band of the N,N-diethyl-2-[(4`-substituted)phenylsulfonyl]acetamides Et(2)NC(O)CH(2)S(O)(2)-C(6)H(4)-Y (Y = OMe 1, Me 2,1-13, Cl 4, Br 5, NO(2) 6) supported by B3LYP/6-31G(d,p) calculations for 3, indicated the existence of three pairs (anti and syn) of cis (c) and gauche (g(1) and g(2)) conformers in the gas phase, being the gauche conformers significantly more stable than the cis ones. The anti geometry is more stable than the syn one, for each pair of cis and gauche conformers. The summing up of the orbital (NBO analysis) and electrostatic interactions justifies quite well the populations and the v(CO) frequencies of the anti and syn pairs of c, g(1) and g(2) conformers. The IR higher carbonyl frequency component whose population is ca. 10%, in CCl(4), may be ascribed to the least stable and most polar cis conformer pair (in the gas phase) and the lower frequency component whose population is ca. 90%, to the summing up of the populations of the two most stable and least polar gauche conformer pairs (g(1) and g(2)) (in the gas phase). The reversal of the cis(c)/gauche (g(1) + g(2)) population ratio observed in chloroform ca. 60% (cis)/40% (gauche) and the occurrence of the most polar cis(c) conformer only, in acetonitrile, strongly suggests the coalescence of the two gauche components in a unique carbonyl band in solution. A further support to this rationalization is given by the single point PCM solvation model performed by HF/6-31G(d,p) method, which showed a progressive increase of the c/(g(1) + g(2)) ratio going from gas to CCl(4), to CHCl(3) and to CH(3)CN. X-ray single crystal analysis of 4 indicates that this compound assumes, in the solid state, the syn-clinal (gauche) conformation with respect to the [O=C-CH(2)-S] moiety, and the most stable anti geometry relative to the [C(O)N(CH(2)CH(3))(2)] fragment. In order to obtain larger energy gain from the crystal packing the molecules of 4 are linked in centrosymmetric dimers through two C-H center dot center dot center dot O interactions (C-H([O-Ph])center dot center dot center dot O([SO2])) forming a step ladder. (C) 2011 Elsevier B.V. All rights reserved.

Mefenpyr-diethyl action on fenoxaprop-p-ethyl detoxification in wheat varieties

Protetores ou safeners protegem culturas contra a injúria de herbicidas. O propósito deste estudo foi investigar a suscetibilidade diferencial de cinco variedades de trigo (Triticum aestivum) ao herbicida fenoxaprop-p-ethyl e o efeito do protetor mefenpyr-diethyl na minimização da injúria do herbicida e sobre o conteúdo de lipídios. As variedades BRS 49, CD 104, CEP 24, IAPAR 78 e Rubi foram pulverizadas com fenoxaprop-p-ethyl (69 g ha-1), fenoxaprop-p-ethyl + mefenpyr‑diethyl (69 g + 18,75 g ha¹) ou mefenpyr-diethyl (18,75 g ha¹). A injúria das plantas foi avaliada visualmente aos 7 e 14 dias após o tratamento (DAT). A atividade da glutationa S-transferase (GST) foi analisada na parte aérea aos 7 DAT, e o conteúdo de lipídios, aos 14 DAT. As variedades CEP 24, IAPAR 78 e Rubi foram mais tolerantes ao fenoxaprop-p-ethyl do que a BRS 49, e a variedade CD 104 rapidamente se recuperou dos sintomas de intoxicação produzidos pelo herbicida. Mefenpyr-diethyl preveniu a injúria da cultura pelo herbicida. A atividade da GST não foi correlacionada diretamente com a desintoxicação do fenoxaprop-p-ethyl. Contudo, o conteúdo de lipídios esteve relacionado à suscetibilidade de trigo ao tratamento de fenoxaprop-p-ethyl.

Mineralization of poly(epsilon-caprolactone)/adipate modified starch blend in agricultural soil

The biodegradability properties of poly(epsilon-caprolactone) (PCL) and modified adipate-starch (AS) blends, using Edenol-3203 (E) as a starch plasticizer, were investigated in laboratory by burial tests of the samples in previously analyzed agricultural soil. The biodegradation process was carried out using the respirometric test according to ASTM D 5988-96, and the mineralization was followed by both variables such as carbon dioxide evolution and mass loss. The results indicated that the presence of AS-E accelerated the biodegradation rate as expected.