双包层光纤侧面耦合器

研究了一种侧面抽运双包层光纤的方法，从被剥除了外包层、端面为350μm×400μm的D型双包层光纤内包层上切下长度为3mm的一段柱体，并胶合在相同的双包层光纤内包层的侧面上，构成了柱体-光纤侧面耦合器。半导体激光器的抽运光从该柱体的一端入射并通过它耦合进入双包层光纤的内包层，实验测得耦合器最大耦合效率为85％。该方法适用于输出功率为数瓦的光纤激光器和放大器的侧面抽运。

Fabrication and amplified spontaneous emission spectrum of Er3+-doped tellurite glass fiber with D-shape cladding

Tellurite glass is proposed as a host for broadband erbium-doped fiber amplifiers because of their excellent optical and chemical properties. A single-mode Er3+-doped tellurite glass fiber with D-shape cladding was fabricated in this work. The characterization of amplified spontaneous emission (ASE) from this newly fabricated Er3+-doped tellurite fibers are exhibited. When pumped at 980 nm, a very broad erbium ASE nearly 150 nm around 1.53 mum is observed. The changes in ASE with regard to fiber lengths and pumping power were measured and discussed. The output of 2 mW from Er3+-doped tellurite fiber ASE source was obtained under the pump power of 660 mW. The broad 1.53 mum emission of Er3+ in tellurite glass fiber can be used as host material for potential broadband optical amplifier and tunable fiber lasers. (C) 2004 Elsevier B.V. All rights reserved.

Optical chemsensors based on etched fibre Bragg gratings in D-shape and multimode fibres

We present an implementation of high-sensitivity optical chemsensors based on FBGs UV-inscribed in D-shape and multimode fibres and sensitized by HF-etching treatment, demonstrating a capability of detecting chemical concentration changes as small as < 0.5%.

Optical chemsensors based on etched fibre Bragg gratings in D-shape and multimode fibres

We present an implementation of high-sensitivity optical chemsensors based on FBGs UV-inscribed in D-shape and multimode fibres and sensitized by HF-etching treatment, demonstrating a capability of detecting chemical concentration changes as small as < 0.5%.

Wavelet transform analysis of truncated fringe patterns in 3-D surface profilometry

Wavelet transform analysis of projected fringe pattern for phase recovery in 3-D shape measurement of objects is investigated. The present communication specifically outlines and evaluates the errors that creep in to the reconstructed profiles when fringe images do not satisfy periodicity. Three specific cases that give raise to non-periodicity of fringe image are simulated and leakage effects caused by each one of them are analyzed with continuous complex Morlet wavelet transform. Same images are analyzed with FFT method to make a comparison of the reconstructed profiles with both methods. Simulation results revealed a significant advantage of wavelet transform profilometry (WTP), that the distortions that arise due to leakage are confined to the locations of discontinuity and do not spread out over the entire projection as in the case of Fourier transform profilometry (FTP).

Nonrigid Structure-From-Motion From 2-D Images Using Markov Chain Monte Carlo

In this paper we present a new method for simultaneously determining three dimensional (3-D) shape and motion of a non-rigid object from uncalibrated two dimensional (2- D) images without assuming the distribution characteristics. A non-rigid motion can be treated as a combination of a rigid rotation and a non-rigid deformation. To seek accurate recovery of deformable structures, we estimate the probability distribution function of the corresponding features through random sampling, incorporating an established probabilistic model. The fitting between the observation and the projection of the estimated 3-D structure will be evaluated using a Markov chain Monte Carlo based expectation maximisation algorithm. Applications of the proposed method to both synthetic and real image sequences are demonstrated with promising results.

Facteurs influencing haptic shape perception

Le but de cette étude était de déterminer la contribution de plusieurs facteurs (le design de la tâche, l’orientation d’angle, la position de la tête et du regard) sur la capacité des sujets à percevoir les différences de formes bidimensionnelles (2-D) en utilisant le toucher haptique. Deux séries d'expériences (n = 12 chacune) ont été effectuées. Dans tous les cas, les angles ont été explorés avec l'index du bras tendu. La première expérience a démontré que le seuil de discrimination des angles 2-D a été nettement plus élevé, 7,4°, que le seuil de catégorisation des angles 2-D, 3,9°. Ce résultat étend les travaux précédents, en montrant que la différence est présente dans les mêmes sujets testés dans des conditions identiques (connaissance des résultats, conditions d'essai visuel, l’orientation d’angle). Les résultats ont également montré que l'angle de catégorisation ne varie pas en fonction de l'orientation des angles dans l'espace (oblique, verticale). Étant donné que les angles présentés étaient tous distribués autour de 90°, ce qui peut être un cas particulier comme dans la vision, cette constatation doit être étendue à différentes gammes d'angles. Le seuil plus élevé dans la tâche de discrimination reflète probablement une exigence cognitive accrue de cette tâche en demandant aux sujets de mémoriser temporairement une représentation mentale du premier angle exploré et de la comparer avec le deuxième angle exploré. La deuxième expérience représente la suite logique d’une expérience antérieure dans laquelle on a constaté que le seuil de catégorisation est modifié avec la direction du regard, mais pas avec la position de la tête quand les angles (non visibles) sont explorés en position excentrique, 60° à la droite de la ligne médiane. Cette expérience a testé l'hypothèse que l'augmentation du seuil, quand le regard est dirigé vers l'extrême droite, pourrait refléter une action de l'attention spatiale. Les sujets ont exploré les angles situés à droite de la ligne médiane, variant systématiquement la direction du regard (loin ou vers l’angle) de même que l'emplacement d'angle (30° et 60° vers la droite). Les seuils de catégorisation n’ont démontré aucun changement parmi les conditions testées, bien que le biais (point d'égalité subjective) ait été modifié (décalage aux valeurs inférieurs à 90°). Puisque notre test avec le regard fixé à l’extrême droite (loin) n'a eu aucun effet sur le seuil, nous proposons que le facteur clé contribuant à l'augmentation du seuil vu précédemment (tête tout droit/regard à droite) doit être cette combinaison particulière de la tête/regard/angles et non l’attention spatiale.

Monocular-based 3-D seafloor reconstruction and ortho-mosaicing by piecewise planar representation

Photo-mosaicing techniques have become popular for seafloor mapping in various marine science applications. However, the common methods cannot accurately map regions with high relief and topographical variations. Ortho-mosaicing borrowed from photogrammetry is an alternative technique that enables taking into account the 3-D shape of the terrain. A serious bottleneck is the volume of elevation information that needs to be estimated from the video data, fused, and processed for the generation of a composite ortho-photo that covers a relatively large seafloor area. We present a framework that combines the advantages of dense depth-map and 3-D feature estimation techniques based on visual motion cues. The main goal is to identify and reconstruct certain key terrain feature points that adequately represent the surface with minimal complexity in the form of piecewise planar patches. The proposed implementation utilizes local depth maps for feature selection, while tracking over several views enables 3-D reconstruction by bundle adjustment. Experimental results with synthetic and real data validate the effectiveness of the proposed approach

Disparity-defined objects moving in depth do not elicit three-dimensional shape constancy

Observers generally fail to recover three-dimensional shape accurately from binocular disparity. Typically, depth is overestimated at near distances and underestimated at far distances [Johnston, E. B. (1991). Systematic distortions of shape from stereopsis. Vision Research, 31, 1351–1360]. A simple prediction from this is that disparity-defined objects should appear to expand in depth when moving towards the observer, and compress in depth when moving away. However, additional information is provided when an object moves from which 3D Euclidean shape can be recovered, be this through the addition of structure from motion information [Richards, W. (1985). Structure from stereo and motion. Journal of the Optical Society of America A, 2, 343–349], or the use of non-generic strategies [Todd, J. T., & Norman, J. F. (2003). The visual perception of 3-D shape from multiple cues: Are observers capable of perceiving metric structure? Perception and Psychophysics, 65, 31–47]. Here, we investigated shape constancy for objects moving in depth. We found that to be perceived as constant in shape, objects needed to contract in depth when moving toward the observer, and expand in depth when moving away, countering the effects of incorrect distance scaling (Johnston, 1991). This is a striking example of the failure of shape con- stancy, but one that is predicted if observers neither accurately estimate object distance in order to recover Euclidean shape, nor are able to base their responses on a simpler processing strategy.

Three-dimensional printing in the construction industry: A review

3D printing (3Dp) has long been used in the manufacturing sector as a way to automate, accelerate production and reduce waste materials. It is able to build a wide variety of objects if the necessary specifications are provided to the printer and no problems are presented by the limited range of materials available. With 3Dp becoming cheaper, more reliable and, as a result, more prevalent in the world at large, it may soon make inroads into the construction industry. Little is known however, of 3Dp in current use the construction industry and its potential for the future and this paper seeks to rectify this situation by providing a review of the relevant literature. In doing this, the three main 3Dp methods of contour crafting, concrete printing and D-shape 3Dp are described which, as opposed to the traditional construction method of cutting materials down to size, deliver only what is needed for completion, vastly reducing waste. Also identified is 3Dp’s potential to enable buildings to be constructed many times faster and with significantly reduced labour costs. In addition, it is clear that construction 3Dp can allow the further inclusion of Building Information Modelling into the construction process - streamlining and improving the scheduling requirements of a project. However, current 3Dp processes are known to be costly, unsuited to large-scale products and conventional design approaches, and have a very limited range of materials that can be used. Moreover, the only successful examples of construction in action to date have occurred in controlled laboratory environments and, as real world trials have yet to be completed, it is yet to be seen whether it can be it equally proficient in practical situations. Key Words: 3D Printing; Contour Crafting; Concrete Printing; D-shape; Building Automation.

20-W average power, high repetition rate, nanosecond pulse with diffraction limit from an all-fiber MOPA system

In this article, we report an all-fiber master oscillator power amplifier (MOPA) system, which can provide high repetition rate and nanosecond pulse with diffraction-limit. The system was constructed using a (2 + 1) X 1 multimode combiner. The Q-Switched, LD pumped Nd:YVO4 solid-state laser wets used (is master oscillator. The 976-nm fiber-coupled module is used as pump source. A 10-m long China-made Yb3+-doped D-shape double-clad large-mode-area fiber was used as amplifier fiber. The MOPA produced as much as 20-W average power with nanosecond pulse and near diffraction limited. The pulse duration is maintained at about 15 its during 50-175 kHz. The system employs a simple and compact architecture and is therefore suitable for the use in practical applications such as scientific and military airborne LIDAR and imaging. Based oil this system. the amplification performances of. the all fiber amplifier is investigated. (C) 2008 Wiley Periodicals, Inc.

Investigation on upconversion luminescence in Er3+/Yb3+ codoped tellurite glasses and fibers

The upconversion properties of Er3+/Yb3+ codoped tellurite glasses and glass fibers with D-shape cladding under 980 mu excitation were investigated. Intense emission bands centered at 531, 546 and 658 nm corresponding to the transitions Er3+: H-2(11/2) -> I-4(15/2) , S-4(3/2) -> I-4(15/2) and F-4(9/2) -> I-4(15/2), respectively, were observed at room temperature. Compared with that in Er3+/Yb3+ codoped tellurite bulk glass, the upconversion luminescence becomes more efficient in the fiber geometry. The dependence of upconversion intensities on fiber geometry and possible upconversion mechanism are discussed and evaluated. The presented Er3+/Yb3+ codoped tellurite fibers with intense upconversion luminescence can be used as potential host materials for upconversion fiber lasers. (c) 2005 Elsevier B.V. All rights reserved.

Fabrication and emission properties of Er3+/Yb3+ codoped tellurite glass fiber for broadband optical amplification

Tellurite glass is proposed as a host for broadband erbium-doped fiber amplifiers because of their excellent optical and chemical properties. A new single mode Er3+/Yb3+ codoped tellurite fiber with D-shape cladding geometry is fabricated in this work. When pumped at 980 nm, a broad erbium amplified spontaneous emission (ASE) nearly 100 nm in the wavelength range of 1450-1650 ran around 1.53 mu m is observed. It was found that the emission spectrum from erbium in tellurite glass fibers is almost twice as broad as the corresponding spectrum in tellurite bulk glass. The changes in ASE with regard to fiber lengths and pumping power were measured and discussed. The output of about 2.3 mW from Er3+/Yb3+ codoped tellurite fiber ASE source is obtained under the pump power of 700 mW. The broad 1.53 mu m emission of Er3+ in Er3+/Yb3+ codoped tellurite glass fiber can be used as host material for potential broadband optical amplifier and tunable fiber lasers. (c) 2005 Elsevier B.V. All rights reserved.

Effects of the dinoflagellate Alexandrium tamarense on early development of the scallop Argopecten irradians concentricus

The effects of Alexandrium tamarense (strain ATHK) on early development of the bay scallop Argopecten irradians concentricus were studied under laboratory conditions. The algal culture was verified by HPLC to produce paralytic shellfish poisoning (PSP) at a level of 37.48 fmol/cell. Survival of the scallop larvae was not affected when they were grown with A. tamarense at concentrations of 500-10,000 cells/ml for 48 h. However, the activity of D-shape larvae was inhibited after 48-h exposure to A. tamarense at the algal cell density of 10,000 cells/ml. Scallop growth was inhibited significantly by A. tantarense during a 14-day exposure starting at the eye-spot larval stage. The size of juvenile scallops in the group of 10,000 cells/ml was only about 32% of that of the controls, although no obvious effect of A. tamarense was found on the rate of larval metamorphosis. All juvenile scallops survived in algal concentrations of 600-2400 cells/ml, however, attachment rates were significantly lower than control values after a 5-h exposure to A. tamarense at concentrations >600 cells/ml, while they were not obviously reduced after only 1 h of exposure. At concentrations >600 cells/ml, the climbing ability of juveniles was clearly reduced by exposure to A. tamarense after only 1 h. The climbing rate and height were only 55% and 45%, respectively, of those of the controls, when exposed to A. tantarense at a concentration of 600 cells/ml. The results indicated that A. tamarense blooms may have detrimental impacts on shellfish at early life stages, therefore, special attention should be paid to the toxic algal blooms in shellfish breeding area. (C) 2003 Elsevier Science B.V. All rights reserved.

Study on impact of dinoflagellate Alexandrium tamarense on life activities of marine bivalves

The effects of a PSP producing dinoflagellate Alexandrium tamarense on marine bivalves at their several important life,stages: egg, D - shape larva, eyespot larva, juvenile and adult, were studied! The results show that the hitching survival, activity, filtration and! growth were adversely affected by the alga and the impact was significantly increased with the increase of algal density. The inhibitory effect on egg hatching was most significant, which the hatching rate was only 30% of the control when exposed to the alga at 100 cell/cm(3) after 36 h. Further experiments show that the algal culture, re-suspended cells and cell fragments had the inhibitory effect, while no such effect was from the cell-free medium, cell contents and standard STX. The results indicate that the alga could produce unknown toxins, rather than PSP, associated with the cell surface.