Performance of concrete made with aggregates recycled from precasting industry waste: influence of the crushing process

The aim of this paper is to evaluate the influence of the crushing process used to obtain recycled concrete aggregates on the performance of concrete made with those aggregates. Two crushing methods were considered: primary crushing, using a jaw crusher, and primary plus secondary crushing (PSC), using a jaw crusher followed by a hammer mill. Besides natural aggregates (NA), these two processes were also used to crush three types of concrete made in laboratory (L20, L45 e L65) and three more others from the precast industry (P20, P45 e P65). The coarse natural aggregates were totally replaced by coarse recycled concrete aggregates. The recycled aggregates concrete mixes were compared with reference concrete mixes made using only NA, and the following properties related to the mechanical and durability performance were tested: compressive strength; splitting tensile strength; modulus of elasticity; carbonation resistance; chloride penetration resistance; water absorption by capillarity; water absorption by immersion; and shrinkage. The results show that the PSC process leads to better performances, especially in the durability properties. © 2014 RILEM

Performance of concrete made with aggregates recycled from precasting industry waste: influence of the crushing process

The aim of this paper is to evaluate the influence of the crushing process used to obtain recycled concrete aggregates on the performance of concrete made with those aggregates. Two crushing methods were considered: primary crushing, using a jaw crusher, and primary plus secondary crushing (PSC), using a jaw crusher followed by a hammer mill. Besides natural aggregates (NA), these two processes were also used to crush three types of concrete made in laboratory (L20, L45 e L65) and three more others from the precast industry (P20, P45 e P65). The coarse natural aggregates were totally replaced by coarse recycled concrete aggregates. The recycled aggregates concrete mixes were compared with reference concrete mixes made using only NA, and the following properties related to the mechanical and durability performance were tested: compressive strength; splitting tensile strength; modulus of elasticity; carbonation resistance; chloride penetration resistance; water absorption by capillarity; water absorption by immersion; and shrinkage. The results show that the PSC process leads to better performances, especially in the durability properties.

Influence of the crushing process of recycled aggregates on concrete properties

This work intends to evaluate the (mechanical and durability) performance of concrete made with coarse recycled concrete aggregates (CRCA) obtained using two crushing processes: primary crushing (PC) and primary plus secondary crushing (PSC). This analysis intends to select the most efficient production process of recycled aggregates (RA). The RA used here resulted from precast products (P), with strength classes of 20 MPa, 45 MPa and 65 MPa, and from laboratory-made concrete (L) with the same compressive strengths. The evaluation of concrete was made with the following tests: compressive strength; splitting tensile strength; modulus of elasticity; carbona-tion resistance; chloride penetration resistance; capillary water absorption; and water absorption by immersion. These findings contribute to a solid and innovative basis that allows the precasting industry to use without restrictions the waste it generates. © (2015) Trans Tech Publications, Switzerland.

Seulamurskaimen murskausominaisuuksien tutkiminen ja kehittäminen

Työn tavoitteena oli kehittää seulamurskaimen murskausprosessia selvittämällä murskaukseen vaikuttavia tekijöitä. Murskausprosessin sisäistämisen myötä voidaan saavuttaa parempi jaekoon hallinta, parantaa kapasiteettia sekä luoda tehokkaampia murskaussovelluksia. Murskausprosessia tutkittiin aluksi murskaukseen vaikuttavien teorioiden kautta. Teoriapohjaista tietoa ja murskaustapahtumaa tutkittiin käytännön testeillä, joissa testattiin seulamurskainta useilla eri materiaaleilla ja erilaisilla tuotevariaatioilla. Testeissä kerättiin näytteitä jaekoon jatkotutkimusta varten sekä saatujen tulosten pohjalta vertailtiin eri tuotevariaatioiden keskeisiä eroja. Saavutettuja tuloksia analysoitiin ja kehitettiin uusia potentiaalisia ratkaisuja seulamurskaimiin. Seulamurskaimen nykyinen rakenne on kehitetty ennen kaikkea seulontasovelluksiin ja sen toiminta perustuu rungon sisällä materiaalin pyörivään liikkeeseen. Murskausprosessissa on kuitenkin oleellista pyrkiä vähentämään sisäistä pyörintäliikettä, joka on hidasteena kappaleiden murskaukselle. Lisäksi seulamurskaimessa on useita rakenteita, jotka on kehitetty erityisesti seulontaa varten ja niiden uudenlaisella rakennesuunnittelulla voitaisiin saavuttaa huomattavasti parempia tuloksia murskauksen kannalta. Nämä tekijät kuitenkin vaativat huomattavan paljon tehoa, mikä puolestaan saattaa asettaa uusia haasteita suunnitteluun, sillä seulamurskaimessa käytettävissä oleva teho on varsin rajallinen.

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

Utilização de bagaço de caju desidratado e complexo enzimático na ração para codornas japonesas em postura

Given the significant share of food costs of poultry production, it is necessary to use strategies and techniques to maximize the utilization and biological value of the components of the diets, keeping constant or improving animal performance. In this context, seeking partial substitution of corn and the best use of the constituents of the diet, the present study aimed to evaluate the effects of inclusion of cashew pomace dehydrated (BCD) and enzyme complex (EC) in the diet on performance and quality eggs of Japanese quails. A total of 200 Japanese quail at 87 days of age, in 25 cages in a completely randomized design in a factorial 2 x 2 + 1 (two levels of cashew bagasse x two levels of enzymes) + control diet without cashew bagasse totaling five treatments with five replicates of eight birds each repetition. The experiment lasted 84 days, divided into four periods of 21 days. The treatments consisted of T1-Ration Control, T2-ration with 7.5% without EC BCD, T3-ration with 7.5% BCD with CE, T4-Ration with 15% BCD without EC and T5-Feed with 15% of BCD with EC. The enzyme complex (EC) is used fermentation product of Aspergillus niger, and cashew bagasse was obtained from the juice industry, passed through drying and crushing process for producing the bran. The performance and egg quality of quails, and performance variables: feed intake (FI), feed conversion ratio per dozen eggs (CAKDZ) and egg mass (CAMO), egg production (OP% bird / day), average egg weight (PMO) and egg mass (MO), and variables were egg quality, specific gravity (SG), Haugh unit (HU), yolk index, and the relationships between components eggs (%albumen,% yolk and %shell). Data were analyzed with the Statistical SAEG (2007). The 7.5 and 15% of cashew bagasse, independent of the enzyme complex decreased feed intake and improved the average egg weight. The two levels with the addition of EC showed significant differences for feed conversion by egg mass. The 7.5 with the addition of enzyme complex obtained the lowest average feed conversion per dozen eggs. The inclusion of up to 15% of cashew bagasse dehydrated with or without addition of enzyme complex in the diet of Japanese quails not interfere in the internal and external quality of eggs. The 7.5 and 15% BCD without added enzyme complex gave better means for specific gravity. Under conditions in which the experiment was conducted, it can be stated that the inclusion of up to 15% of cashew bagasse dehydrated with added enzyme complex feeding quail is economically viable, with the level of 7.5% with the addition of complex enzyme presented the best economic indices

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

A combined vacuum crushing and sieving (CVCS) system designed to determine noble gas palaeo-temperatures from stalagmite samples

This paper presents a novel extraction device for water and noble gases from speleothem samples for noble gas paleotemperature determination. The “combined vacuum crushing and sieving (CVCS) system” was designed to reduce the atmospheric noble gas contents from air inclusions in speleothem samples by up to 2 orders of magnitude without adsorbing atmospheric noble gases onto the freshly produced grain surfaces, a process that had often hampered noble gas temperature (NGT) determination in the past. We also present the results from first performance tests of the CVCS system processing stalagmite samples grown at a known temperature. This temperature is reliably reproduced by the NGTs derived from Ar, Kr, and Xe extracted from the samples. The CVCS system is, therefore, suitable for routine determinations of accurate NGTs. In combination with stalagmite dating, these NGTs will allow reconstructing past regional temperature evolutions, and also support the interpretation of the often complex stable isotope records preserved in the stalagmites' calcite.

A combined vacuum crushing and sieving (CVCS) system designed to determine noble gas paleotemperatures from stalagmite samples

This paper presents a novel extraction device for water and noble gases from speleothem samples for noble gas paleotemperature determination. The “combined vacuum crushing and sieving (CVCS) system” was designed to reduce the atmospheric noble gas contents from air inclusions in speleothem samples by up to 2 orders of magnitude without adsorbing atmospheric noble gases onto the freshly produced grain surfaces, a process that had often hampered noble gas temperature (NGT) determination in the past. We also present the results from first performance tests of the CVCS system processing stalagmite samples grown at a known temperature. This temperature is reliably reproduced by the NGTs derived from Ar, Kr, and Xe extracted from the samples. The CVCS system is, therefore, suitable for routine determinations of accurate NGTs. In combination with stalagmite dating, these NGTs will allow reconstructing past regional temperature evolutions, and also support the interpretation of the often complex stable isotope records preserved in the stalagmites' calcite.

[meanings Of The Sickening Process For Patients With Systemic Lupus Erythematosus: A Review Of The Literature.]

Systemic lupus erythematosus is an autoimmune disease that causes many psychological repercussions that have been studied through qualitative research. These are considered relevant, since they reveal the amplitude experienced by patients. Given this importance, this study aims to map the qualitative production in this theme, derived from studies of experiences of adult patients of both genders and that had used as a tool a semi-structured interview and/or field observations, and had made use of a sampling by a saturation criterion to determine the number of participants in each study. The survey was conducted in Pubmed, Lilacs, Psycinfo e Cochrane databases, searching productions in English and Portuguese idioms published between January 2005 and June 2012. The 19 revised papers that have dealt with patients in the acute phase of the disease showed themes that were categorized into eight topics that contemplated the experienced process at various stages, from the onset of the disease, extending through the knowledge of the diagnosis and the understanding of the manifestations of the disease, drug treatment and general care, evolution and prognosis. The collected papers also point to the difficulty of understanding, of the patients, on what consists the remission phase, revealing also that this is a clinical stage underexplored by psychological studies.

[in Process Citation].

20

O aluno com deficiência visual nas aulas de educação física : análise do processo inclusivo = The student with visual impairments : analysis of inclusive process

Universidade Estadual de Campinas . Faculdade de Educação Física

Hegemonia e contra-hegemonia na construção de políticas de esporte e lazer : a experiência do Consórcio Brasília = Hegemony and counter-hegemony in the process of sport and leisure policy-making : the experience of the Consortium Brasilia

Universidade Estadual de Campinas . Faculdade de Educação Física

Effects of the condylar process fracture on facial symmetry in rats submitted to protein undernutrition

PURPOSE: To investigate the facial symmetry of rats submitted to experimental mandibular condyle fracture and with protein undernutrition (8% of protein) by means of cephalometric measurements. METHODS: Forty-five adult Wistar rats were distributed in three groups: fracture group, submitted to condylar fracture with no changes in diet; undernourished fracture group, submitted to hypoproteic diet and condylar fracture; undernourished group, kept until the end of experiment, without condylar fracture. Displaced fractures of the right condyle were induced under general anesthesia. The specimens were submitted to axial radiographic incidence, and cephalometric mensurations were made using a computer system. The values obtained were subjected to statistical analyses among the groups and between the sides in each group. RESULTS: There was significative decrease of the values of serum proteins and albumin in the undernourished fracture group. There was deviation of the median line of the mandible relative to the median line of the maxilla, significative to undernutrition fracture group, as well as asymmetry of the maxilla and mandible, in special in the final period of experiment. CONCLUSION: The mandibular condyle fracture in rats with proteic undernutrition induced an asymmetry of the mandible, also leading to consequences in the maxilla.

Influence of specimens' design and manufacturing process on microtensile bond strength to enamel: laboratory and FEA comparison

This study evaluated the effect of specimens' design and manufacturing process on microtensile bond strength, internal stress distributions (Finite Element Analysis - FEA) and specimens' integrity by means of Scanning Electron Microscopy (SEM) and Laser Scanning Confocal Microscopy (LCM). Excite was applied to flat enamel surface and a resin composite build-ups were made incrementally with 1-mm increments of Tetric Ceram. Teeth were cut using a diamond disc or a diamond wire, obtaining 0.8 mm² stick-shaped specimens, or were shaped with a Micro Specimen Former, obtaining dumbbell-shaped specimens (n = 10). Samples were randomly selected for SEM and LCM analysis. Remaining samples underwent microtensile test, and results were analyzed with ANOVA and Tukey test. FEA dumbbell-shaped model resulted in a more homogeneous stress distribution. Nonetheless, they failed under lower bond strengths (21.83 ± 5.44 MPa)c than stick-shaped specimens (sectioned with wire: 42.93 ± 4.77 MPaª; sectioned with disc: 36.62 ± 3.63 MPa b), due to geometric irregularities related to manufacturing process, as noted in microscopic analyzes. It could be concluded that stick-shaped, nontrimmed specimens, sectioned with diamond wire, are preferred for enamel specimens as they can be prepared in a less destructive, easier, and more precise way.