Multi-body modelling of wagon trains for crashworthiness analysis

Three-dimensional wagon train models have been developed for the crashworthiness analysis using multi-body dynamics approach. The contributions of the train size (number of wagon) to the frontal crash forces can be identified through the simulations. The effects of crash energy management (CEM) design and crash speed on train crashworthiness are examined. The CEM design can significantly improve the train crashworthiness and the consequential vehicle stability performance - reducing derailment risks.

Analysis of crush behaviours of a rail cab car and structural modifications for improved crashworthiness

In this paper, the authors present a crashworthiness assessment and suggestions for modification of a conventionally designed rail vehicle with a driving cab (cab car). The analytical approach, based on numerical analysis, consisted of two stages. Firstly, the crashworthiness of the cab car was assessed by simulating a collision between the cab car and a rigid wall. Then, after analysing structural weaknesses, the design of the cab car was modified and simulated again in the same scenario. It was found that downward bending is an intrinsic weakness in conventional rail vehicles and that jackknifing is a main form of failures in conventional rail vehicle components. The cab car, as modified by the authors, overcomes the original weaknesses and shows the desired progressive collapse behaviour in simulation. The conclusions have general relevance for other studies but more importantly, point to the need for a rethink of some aspects of rail vehicle design.

A scaling method for modelling the crashworthiness of novel roadside barrier designs

In this paper, a novel method for modelling a scaled vehicle–barrier crash test similar to the 20◦ angled barrier test specified in EN 1317 is reported. The intended application is for proof-of-concept evaluation of novel roadside barrier designs, and as a cost-effective precursor to full-scale testing or detailed computational modelling. The method is based on the combination of the conservation of energy law and the equation of motion of a spring mass system representing the impact, and shows, for the first time, the feasibility of applying classical scaling theories to evaluation of roadside barrier design. The scaling method is used to set the initial velocity of the vehicle in the scaled test and to provide scaling factors to convert the measured vehicle accelerations in the scaled test to predicted full-scale accelerations. These values can then be used to calculate the Acceleration Severity Index score of the barrier for a full-scale test. The theoretical validity of the method is demonstrated by comparison to numerical simulations of scaled and full-scale angled barrier impacts using multibody analysis implemented in the crash simulation software MADYMO. Results show a maximum error of 0.3% ascribable to the scaling method.

Predicting impact damage, residual strength and crashworthiness of composite structures

The development of the latest generation of wide-body carbon-fibre composite passenger aircraft has heralded a new era in the utilisation of these materials. The premise of superior specific strength and stiffness, corrosion and fatigue resistance, is tempered by high development costs, slow production rates and lengthy and expensive certification programmes. Substantial effort is currently being directed towards the development of new modelling and simulation tools, at all levels of the development cycle, to mitigate these shortcomings. One of the primary challenges is to reduce the extent of physical testing, in the certification process, by adopting a ‘certification by simulation’ approach. In essence, this aspirational objective requires the ability to reliably predict the evolution and progression of damage in composites. The aerospace industry has been at the forefront of developing advanced composites modelling tools. As the automotive industry transitions towards the increased use of composites in mass-produced vehicles, similar challenges in the modelling of composites will need to be addressed, particularly in the reliable prediction of crashworthiness. While thermoset composites have dominated the aerospace industry, thermoplastics composites are likely to emerge as the preferred solution for meeting the high-volume production demands of passenger road vehicles. This keynote presentation will outline recent progress and current challenges in the development of finite-element-based predictive modelling tools for capturing impact damage, residual strength and energy absorption capacity of thermoset and thermoplastic composites for crashworthiness assessments.

A novel method of tube manufacture for vehicle crashworthiness utilising the QUICKSTEP™ Process.

A novel method of composite tube manufacture was developed for potential use in automotive crash structures. Tubes were crushed axially under quasi-static conditions and highly repeatable behaviour was observed with an average specific energy absorption of -85kJ/kg. DMTA results indicated that the tubes were fully cured, even when the cycle was reduced to 7 minutes, giving this process huge potential for high-volume production.

Development of material models to predict the crashworthiness of tubes

Metallic tubes have been extensively studied for their crashworthiness as they closely resemble automotive crash rails. Recently, the demand to produce light weight yet safer vehicles has led to the need to understand the behaviour of novel materials such as composites, metallic foams and sandwich structures durign a crash. This paper presents a method to predict the crashworthiness of structural components using material modes. The material factors that most affect the crushing response are determined and quantified by developing and validating the crushing of a square tube model in Abaqus. The inputs from the model are used to construct a simple, physically realistic constitutive model and new test methods for predicting the material behaviour at high strain rates using low test speeds. These material models enable a designer to predict the crash behaviour of a structure without the need to perform extensive physical tests, thus reducing the time and cost of development.

Crashworthiness and composite materials: development of an experimental test method for the energy absorption determination and implementation of the relative numerical model

In this PhD thesis the crashworthiness topic is studied with the perspective of the development of a small-scale experimental test able to characterize a material in terms of energy absorption. The material properties obtained are then used to validate a nu- merical model of the experimental test itself. Consequently, the numerical model, calibrated on the specific ma- terial, can be extended to more complex structures and used to simulate their energy absorption behavior. The experimental activity started at University of Washington in Seattle, WA (USA) and continued at Second Faculty of Engi- neering, University of Bologna, Forl`ı (Italy), where the numerical model for the simulation of the experimental test was implemented and optimized.

Effetto di impatti sul comportamento crashworthiness di materiali compositi

Attività sperimentale riguardante lo studio dei materiali compositi, nell’ambito della progettazione a crashworthiness, svolto, tramite test dei provini realizzati nell’attività di tirocinio, presso i laboratori didattici della Scuola di ingegneria e architettura, sede di Forlì. Il lavoro di tesi, si è basato sulla valutazione dell’energia assorbita dai provini in materiale composito, tramite prove quasi-statiche; per questo tipo di prove sono stati utilizzati provini autostabilizzanti, rinforzati in fibra di carbonio e matrice in resina epossidica. Prima di procedere alla sperimentazione, sono stati studiati i risultati ottenuti da precedenti sperimentazioni eseguite da colleghi, per valutare quale fosse la configurazione migliore di provino, in termini di geometria, e trigger, che garantisse elevate energie di assorbimento. Dopo una panoramica dei materiali compositi, con riferimento alle caratteristiche e proprietà, alle diverse tipologie che si possono avere in ambito industriale, è spiegato il concetto di crashworthiness, le varie tipologie di test di impatto e le varie tipologie di rottura alla quale può essere soggetto un provino. Si è di seguito descritto come è stata valutata la scelta del tipo di geometria e del trigger, che sarebbero stati utilizzati per la progettazione del provino, e si è accennato al processo di laminazione svolta presso i laboratori della Scuola per la fabbricazione del provino. Al termine della descrizione dei tester usati per la sperimentazione sono, infine, illustrati i risultati delle prove svolte, con successivi commenti.

Crashworthiness analysis of the UMTA state-of-the-art cars. Final report.

Transportation Systems Center, Cambridge, Mass.

Compliance and crashworthiness tests on an electric vehicle - 1975 Metro-Electric 4-door sedan. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Rail safety/ equipment crashworthiness. Volume IV: Executive summary. Interim report.

Federal Railroad Administration, Office of Research and Development, Washington, D.C.

Rail safety/ equipment crashworthiness. Volume II: Design guide. Interim report.

Federal Railroad Administration, Office of Research and Development, Washington, D.C.