Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin

Objectives: The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. Materials and Methods: Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n=7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60days. All specimens were thermal cycled between 5 and 55°C with 30-s dwell times for 1000 cycles before and after disinfection. The specimens' colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T 1), after disinfection (D) and after second thermal cycling (T 2). Colour differences (ΔE) were calculated between T 1 and B (T 1B), D and B (DB), and T 2 and B (T 2B) time-points. Results: The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time-points, except for the Lucitone acrylic resin. Conclusions: The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters. © 2012 The Gerodontology Society and John Wiley & Sons A/S.

Influence of natural weathering on colour stability of materials used for facial prosthesis

Colour stability of resin and silicone is an important factor for longevity of facial prostheses. The aim of this study was to evaluate the colour stability of resins and silicone for facial prostheses. Three brands of acrylic resin and one of facial silicone were evaluated considering pigment incorporation for the colourless materials. Ten samples of each material were fabricated and submitted to measurements of chromatic alteration initially and after 90 and 180 days of weathering natural through visual analysis and spectrophotometry. Data were evaluated by ANOVA and Tukey test (p < 0.05). Statistically significant colour alteration was observed among some materials regardless of the period. The materials did not present a statistical difference between 90 and 180 days except for the pigmented heat-polymerized resin. The colour difference between pigmented Silastic MDX4-4210 and colourless Silastic was statistically significant (p < 0.01) in both periods as well as between pigmented and colourless heat-polymerized resin, and between the resins Rapidaflex and Lentaflex. The visual method demonstrated colour alteration in all materials evaluated during the first 90 days of ageing. All materials exhibited colour alteration due to exposure to environment. © 2012 Informa UK, Ltd.

Colour stability of acrylic resin denture teeth after immersion in different beverages

The colour stability of acrylic resin denture teeth in beverages was investigated. A spectrophotometer measured the colour (CIE-L*a*b* system) of all specimens after storage in distilled water for 24 h at 37°C (T0). Specimens were then immersed in various beverages. After 15 days (T1) and 30 days (T2), for each material, the mean ∆E values were calculated and compared by two-way ANOVA and Tukey intervals (α=0.05). In the ∆T0T1 period, specimens stored in red wine were significantly discoloured, compared to distilled water (P=0.003). There was no difference between immersion solutions in ∆ET0T2 (P=0.772) and in ∆ET1T2 (P=0.058), and no difference between materials in all immersion periods.

Influence of artificial accelerated ageing on the colour stability of paints used for ocular prosthesis iris painting

Objectives: To evaluate the colour stability of paints used for ocular prosthesis iris painting submitted for accelerated artificial ageing (AAA). Materials and methods: Forty specimens of acrylic resin for sclera (16 x 2 mm) were made and separated into eight groups (n = 10) according to the type of paint (gouache, GP; oil, OP; acrylic AP; and composite resin for characterisation, CR) and the colours used (blue/brown). After drying (72 h), a new layer of colourless acrylic resin was applied and the initial colour readout was performed (Spectrophotometer PCB 6807). New colour readouts were performed after AAA, and Delta E was calculated. Results: Statistical analysis (two-way ANOVA-Bonferroni, p < 0.05) demonstrated that the brown colour showed lower Delta E means in comparison with the blue colour, with statistically significant difference for AP only. Blue colour showed no statistically significant difference with regard to the type of paint used. Brown AP showed lower Delta E than the other groups, with significant difference for OP and GP. GP showed greater alteration in Delta E for the brown colour, being statistically similar only to OP. Conclusions: Only the AP group for brown pigment shows clinically acceptable values for colour stability after AAA.

Sensing colour stability and mixtures of powder paprika using optical reflectance and image analysis.

The production and industry of paprika present several problems related to quality and to production costs. One of the main difficulties is to obtain an objective and quick method for predicting quality. Quality in powder paprika involves: quantity of carotenoids and the appearance and stability of colour. The method used currently for determining quality is the measurement of absorbance at 460 nm wavelength, of an acetone extract of carotenoids, but there is no information about the appearance of the paprika or the stability of its colour with time. " Another important problem is the presence of mixtures of powdered paprika produced in the Spanish region of "La Vera", which has a peculiar way of production, with a high '' quality and price, with other products of lower quality. It is necessary to obtain methods which are able to detect the fraud.

Comparison of the color stability and lipid oxidative stability of fresh vacuum packaged lamb muscle containing elevated omega-3 and omega-6 fatty acid levels from dietary manipulation

A series of three experiments were conducted with second cross ([Merino×Border Leicester]×Poll Dorset) wether lambs to evaluate the effects of dietary treatments on manipulation of muscle long-chain (LC) omega-3 fatty acids (FA) on the color stability and oxidative stability of fresh and vacuum packaged lamb. At the end of 7-, 6- and 6-week experimental periods for experiments (Exp.) 1–3 respectively, lambs were slaughtered at a commercial abattoir. At 24 h post-mortem, muscle longissimus lumborum (LL) and longissimus thoracis (LT) were removed and evaluated for color and lipid oxidative stability under specified commercial storage and display condition. Of the dietary supplements used, fish meal and fish oil moderately (P<0.01) and markedly (P<0.001) increased muscle omega-3 FA content, while both protected canola seed (P<0.001) and protected sunflower meal protein significantly (P<0.02) increased muscle omega-6 FA content or ratio of omega-6/omega-3 of the longissimus muscle. In all experiments, the substantial increase (P<0.001) in muscle LC omega-3 and omega-6 FA had no consistent significant effect on color values (redness (a*), yellowness (b*) and lightness (L*)) for fresh and vacuum packaged lamb over a 6-day display period. Lipid oxidation, determined by the levels of thiobarbituric acid reactive substances (TBARS) indicated the enrichment of muscle polyunsaturated fatty acid (PUFA) levels in lambs did not produce significant differences resulting either from main treatment effects or for treatment×day×type interactions (where type was fresh and vacuum packaged). Present results demonstrated the color and lipid oxidative stability of lamb longissimus muscle during refrigerated display was not affected by enhanced levels of omega-3 and omega-6 FA due to dietary treatments.

Colour change of soft denture liners after storage in coffee and coke

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The impact of supplementing lambs with algae on growth, meat traits and oxidative status

The current study examined the effect of supplementing lambs with algae. Forty, three month old lambs were allocated to receive a control ration based on oats and lupins (n=20) or the control ration with DHA-Gold™ algae (~2% of the ration, n=20). These lambs came from dams previously fed a ration based on either silage (high in omega-3) or oats and cottonseed meal (OCSM: high in omega-6) at joining (dam nutrition, DN). Lamb performance, carcase weight and GR fat content were not affected by treatment diet (control vs algae) or DN (silage vs OSCM). Health claimable omega-3 fatty acids (EPA+DHA) were significantly greater in the LL of lambs fed algae (125±6mg/100g meat) compared to those not fed algae (43±6mg/100g meat) and this effect was mediated by DN. Supplementing with algae high in DHA provides a means of improving an aspect of the health status of lamb meat.

Evaluation of experimental cleanser solution of Ricinus communis: effect on soft denture liner properties

Objective: This study evaluated colour stability, hardness and roughness of soft denture liners after immersion in various cleansers. Materials and methods: Thirty specimens (14 mm x 4 mm) of Elite Soft Relining (ES) and Mucopren Soft (MS) were randomly immersed in distilled water at 37 degrees C, sodium hypochlorite 1%, and an experimental Ricinus communis solution (RC) for 7, 15 and 183 continuous days. Results: ANOVA (p < 0.05) and Tukey's test indicated that after T7 (mu =8.79 +/- 7.36); T15 (mu = 4.23 +/- 2.62) and T183 (mu = 8.78 +/- 3.16), MS presented a higher increase in hardness than ES. After T7, MS underwent an increase in roughness (mu = 0.09 +/- 0.80); ES underwent a decrease (mu = -0.08 +/- 0.16). RC caused the smallest variation in roughness. After T15, both materials presented an increase in roughness. After T183, ES (mu = -0.30 +/- 0.48) presented a higher roughness variation than MS (mu = -0.07 +/- 0.32). Hypochlorite caused an increase in roughness (mu = 0.02 +/- 0.19). Conclusion: After all periods ES presented higher colour alteration than MS; highest colour alteration was caused by hypochlorite. Both materials were more stable after immersion in RC.

1-, 2- and 3-dimensional phenylene-based materials for optoelectronic applications

A series of oligo-phenylene dendronised conjugated polymers was prepared. The divergent synthetic approach adopted allowed for the facile synthesis of a range of dendronised monomers from a common intermediate, e.g. first and second generation fluorene. Only the polymerisation of the first generation and alkylarylamine substituted dendronised fluorene monomers yielded high molecular weight materials, attributed to the low solubility of the remaining dendronised monomers. The alkylarylamine substituted dendronised poly(fluorene) was incorporated into an organic light emitting diode (OLED) and exhibited an increased colour stability in air compared to other poly(fluorenes). The concept of dendronisation was extended to poly(fluorenone), a previously insoluble material. The synthesis of the first soluble poly(fluorenone) was achieved by the incorporation of oligo-phenylene dendrons at the 4-position of fluorenone. The dendronisation of fluorenone allowed for a polymer with an Mn of 4.1 x 104 gmol-1 to be prepared. Cyclic voltammetry of the dendronised poly(fluorenone) showed that the electron affinity of the polymer was high and that the polymer is a promising n-type material. A dimer and trimer of indenofluorene (IF) were prepared from the monobromo IF. These oligomers were investigated by 2-dimensional wide angle x-ray spectroscopy (2D-WAXS), polarised optical microscopy (POM) and dielectric spectroscopy, and found to form highly ordered smetic phases. By attaching perylene dye as the end-capper on the IF oligomers, molecules that exhibited efficient Förster energy transfer were obtained. Indenofluorene monoketone, a potential defect structure for IF based OLED’s, was synthesised. The synthesis of this model defect structure allowed for the long wavelength emission in OLED’s to be identified as ketone defects. The long wavelength emission from the indenofluorene monoketone was found to be concentration dependent, and suggests that aggregate formation is occurring. An IF linked hexa-peri-hexabenzocoronene (HBC) dimer was synthesised. The 2D-WAXS images of this HBC dimer demonstrate that the molecule exhibits intercolumnar organisation perpendicular to the extrusion direction. POM images of mixtures of the HBC dimer mixed with an HBC with a low isotropic temperature demonstrated that the HBC dimer is mixing with the isotropic HBC.

Investigation of the oxidative degradation mechanisms and melt stabilisation of a new generation metallocene polytehylene

The two main objectives of the research work conducted were firstly, to investigate the processing and rheological characteristics of a new generation metallocene catalysed linear low density polyethylene (m-LLDPE), in order to establish the thermal oxidative degradation mechanism, and secondly, to examine the role of selected commercial stabilisers on the melt stability of the polymers. The unstabilised m-LLDPE polymer was extruded (pass I) using a twin screw extruder, at different temperatures (210-285°C) and screw speeds (50-20rpm) and was subjected to multiple extrusions (passes, 2-5) carried out under the same processing conditions used in the first pass. A traditional Ziegler/Natta catalysed linear low density polyethylene (z-LLDPE) produced by the same manufacturer was also subjected to a similar processing regime in order to compare the processability and the oxidative degradation mechanism (s) of the new m-LLDPE with that of the more traditional z-LLDPE. The effect of some of the main extrusion characteristics of the polymers (m-LLDPE and z-LLDPE) on their melt rheological behaviour was investigated by examining their melt flow performance monitored at two fixed low shear rate values, and their rheological behaviour investigated over the entire shear rates experienced during extrusion using a twin-bore capillary rheometer. Capillary rheometric measurements, which determine the viscous and elastic properties of polymers, have shown that both polymers are shear thinning but the m-LLDPE has a higher viscosity than z-LLDPE and the extent of reduction in viscosity of the former when the extrusion temperature was increased from 210°C to 285°C was much higher than in the case of the z-LLDPE polymer. This was supplied by the findings that the m-LLDPE polymer required higher power consumption under all extrusion conditions examined. It was fUliher revealed that the m-LLDPE undergoes a higher extent of melt fracture, the onset of which occurs under much lower shear rates than the Ziegler-based polymer and this was attributed to its higher shear viscosity and narrower molecular weight distribution (MWD). Melt flow measurements and GPC have shown that after the first extrusion pass, the initial narrower MWD of m-LLDPE is retained (compared to z-LLDPE), but upon further multiple extrusion passes it undergoes much faster broadening of its MWD which shifts to higher Mw polymer fractions, paliicularly at the high screw speeds. The MWD of z-LLDPE polymer on the other hand shifts towards the lower Mw end. All the evidence suggest therefore the m-LLDPE undergoes predominantly cross-linking reactions under all processing conditions whereas z-LLDPE undergoes both cross-linking and chain scission reactions with the latter occurring predominantly under more severe processing conditions (higher temperatures and screw speeds, 285°CI200rpm). The stabilisation of both polymers with synergistic combinations of a hindered phenol (Irganox 1076) and a phosphite (Weston 399) at low concentrations has shown a high extent of melt stabilisation in both polymers (extrusion temperatures 210-285°C and screw speeds 50-200rpm). The best Irganox 1076/Weston 399 system was found to be at an optimum 1:4 w/w ratio, respectively and was found to be most effective in the z-LLDPE polymer. The melt stabilising effectiveness of a Vitamin E/Ultranox 626 system used at a fraction of the total concentration of Irganox 1076/Weston 399 system was found to be higher in both polymers (under all extrusion conditions). It was found that AOs which operate primarily as alkyl (Re) radical scavengers are the most effective in inhibiting the thermal oxidative degradation of m-LLDPE in the melt; this polymer was shown to degrade in the melt primarily via alky radicals resulting in crosslinking. Metallocene polymers stabilised with single antioxidants of Irganox HP 136 (a lactone) and Irganox E201 (vitamin E) produced the highest extent of melt stability and the least discolouration during processing (260°C/1 OOrpm). Furthermore, synergistic combinations of Irganox HP I 36/Ultranox 626 (XP-60) system produced very high levels of melt and colour stability (comparable to the Vitamin E based systems) in the mLLDPE polymer. The addition of Irganox 1076 to an Irganox HP 136/Ultranox 626 system was found not to result in increasing melt stability but gave rise to increasing discolouration of the m-LLDPE polymer. The blending of a hydroxylamine (lrgastab FS042) with a lactone and Vitamin E (in combination with a phosphite) did not increase melt stability but induced severe discolouration of resultant polymer samples.

Learning from mother nature:exploiting a biological antioxidant for the melt stabilisation of polymers

An overview of the antioxidant role of the biologically active form of vitamin E, α-tocopherol, in polyolefins is discussed. The effect of the vitamin antioxidant on the melt and colour stability of polyethylene (PE) and polypropylene (PP) is highlighted. It is shown that tocopherol is a highly effective antioxidant that results in superior melt stabilisation of polyolefins particularly when used at much lower concentration than that needed for conventional synthetic hindered phenol processing stabilisers. As with other hindered phenols,α-tocopherol imparts also some colour to the polymer but this is shown to be reduced drastically in the presence of other antioxidants, such as phosphites, or other additives, such as polyhydric alcohols.

Comparação de materiais usados na confeção de facetas dentárias

A demanda na procura da reabilitação estética é um dos focos da história da humanidade ao longo das eras, mas que teve a sua acentuação nestes últimos dois séculos. Sendo a face um dos pontos que nos permite avaliar esteticamente uma pessoa, cabe ao médico dentista, como um dos profissionais que trabalha nessa zona do corpo humano, avaliar e procurar satisfazer as necessidades estéticas da população. Assim, por parte dos profissionais de Medicina Dentária, tem de haver uma procura constante para a satisfação das exigências estéticas, não só no conhecimento como no aprimoramento da técnica. Nos últimos tempos, com a necessidade de desenvolvimento de materiais para colmatar a cada vez maior busca para a perfeição estética, as facetas surgiram como tratamento de excelência. O presente trabalho teve como objectivo a comparação entre resina composta e cerâmica, na elaboração de restaurações estéticas. Para os dois tipos de materiais foram avaliados a estética e o comportamento biomecânico. Foram comparados benefícios e desvantagens, contra-indicações, indicações, plano de tratamento, diagnóstico e procedimentos clínicos dos dois materiais, utilizados na confecção das facetas cerâmicas e de resina composta. Foram utilizados os seguintes parâmetros de comparação: biocompatibilidade, adaptação marginal, preparação, resistência, cor, acabamento, potencial de reparação, custo e estética. A utilização de facetas cerâmicas tem sido um dos principais focos de desenvolvimento da Medicina Dentária no âmbito científico. A sua utilização permite uma maior predictibilidade e uma maior longevidade clínica. A sua qualidade estética, resistência à fractura, biodisponibilidade e estabilidade de cor, são as suas maiores vantagens na utilização clínica. Em sentido inverso, as facetas de resina composta apresentam menor custo, maior resistência à abrasão, possibilidade de reparação fácil e menor desgaste de estrutura dentária durante a sua preparação. Contudo apresentam menor estabilidade de cor. Portanto, torna-se esclarecedor que a escolha do material a utilizar na confecção de facetas, deve ser adaptada às especificidades de cada caso.