Co-simulation tools for networked control systems: revision and utilization

Networked control systems (NCSs) are distributed control systems in which the sensors, actuators, and controllers are physically separated and connected through an industrial network. The main challenge related to the development of NCSs is the degenerative effects caused by the inclusion of this communication network in the closed loop control. In order to mitigate these effects, co-simulation tools for NCS have been developed to study the network influence in the NCS. This paper presents a revision about co-simulation tools for NCS and the application of two of these tools for the design and evaluation of NCSs. The TrueTime and Jitterbug tools were used together to evaluate the main configuration parameter that affects the performance of CAN-based NCS and to verify the NCS quality of control under various timing conditions including different transmission period of messages and network delays. Therefore, the simulation results led to the conclusion that despite the transmission period of messages is the most significant factor among the analyzed in the design of NCS, its influence is related to the kind of system with greater effects in NCSs with fast dynamics.

Nonlinear/electromagnetic co-simulation of microwaves and millimeter-waves links

The Ph.D. thesis describes the simulations of different microwave links from the transmitter to the receiver intermediate-frequency ports, by means of a rigorous circuit-level nonlinear analysis approach coupled with the electromagnetic characterization of the transmitter and receiver front ends. This includes a full electromagnetic computation of the radiated far field which is used to establish the connection between transmitter and receiver. Digitally modulated radio-frequency drive is treated by a modulation-oriented harmonic-balance method based on Krylov-subspace model-order reduction to allow the handling of large-size front ends. Different examples of links have been presented: an End-to-End link simulated by making use of an artificial neural network model; the latter allows a fast computation of the link itself when driven by long sequences of the order of millions of samples. In this way a meaningful evaluation of such link performance aspects as the bit error rate becomes possible at the circuit level. Subsequently, a work focused on the co-simulation an entire link including a realistic simulation of the radio channel has been presented. The channel has been characterized by means of a deterministic approach, such as Ray Tracing technique. Then, a 2x2 multiple-input multiple-output antenna link has been simulated; in this work near-field and far-field coupling between radiating elements, as well as the environment factors, has been rigorously taken into account. Finally, within the scope to simulate an entire ultra-wideband link, the transmitting side of an ultrawideband link has been designed, and an interesting Front-End co-design technique application has been setup.

Nonlinear / electromagnetic co-simulation and co-design of microwave links in highly polluted and / or strongly inhomogeneous environments

The objective of the Ph.D. thesis is to put the basis of an all-embracing link analysis procedure that may form a general reference scheme for the future state-of-the-art of RF/microwave link design: it is basically meant as a circuit-level simulation of an entire radio link, with – generally multiple – transmitting and receiving antennas examined by EM analysis. In this way the influence of mutual couplings on the frequency-dependent near-field and far-field performance of each element is fully accounted for. The set of transmitters is treated as a unique nonlinear system loaded by the multiport antenna, and is analyzed by nonlinear circuit techniques. In order to establish the connection between transmitters and receivers, the far-fields incident onto the receivers are evaluated by EM analysis and are combined by extending an available Ray Tracing technique to the link study. EM theory is used to describe the receiving array as a linear active multiport network. Link performances in terms of bit error rate (BER) are eventually verified a posteriori by a fast system-level algorithm. In order to validate the proposed approach, four heterogeneous application contexts are provided. A complete MIMO link design in a realistic propagation scenario is meant to constitute the reference case study. The second one regards the design, optimization and testing of various typologies of rectennas for power generation by common RF sources. Finally, the project and implementation of two typologies of radio identification tags, at X-band and V-band respectively. In all the cases the importance of an exhaustive nonlinear/electromagnetic co-simulation and co-design is demonstrated to be essential for any accurate system performance prediction.

Modelling and analysis of networked control strategies in smart power distribution grids: development of co-simulation tools

This thesis is focused on Smart Grid applications in medium voltage distribution networks. For the development of new applications it appears useful the availability of simulation tools able to model dynamic behavior of both the power system and the communication network. Such a co-simulation environment would allow the assessment of the feasibility of using a given network technology to support communication-based Smart Grid control schemes on an existing segment of the electrical grid and to determine the range of control schemes that different communications technologies can support. For this reason, is presented a co-simulation platform that has been built by linking the Electromagnetic Transients Program Simulator (EMTP v3.0) with a Telecommunication Network Simulator (OPNET-Riverbed v18.0). The simulator is used to design and analyze a coordinate use of Distributed Energy Resources (DERs) for the voltage/var control (VVC) in distribution network. This thesis is focused control structure based on the use of phase measurement units (PMUs). In order to limit the required reinforcements of the communication infrastructures currently adopted by Distribution Network Operators (DNOs), the study is focused on leader-less MAS schemes that do not assign special coordinating rules to specific agents. Leader-less MAS are expected to produce more uniform communication traffic than centralized approaches that include a moderator agent. Moreover, leader-less MAS are expected to be less affected by limitations and constraint of some communication links. The developed co-simulator has allowed the definition of specific countermeasures against the limitations of the communication network, with particular reference to the latency and loss and information, for both the case of wired and wireless communication networks. Moreover, the co-simulation platform has bee also coupled with a mobility simulator in order to study specific countermeasures against the negative effects on the medium voltage/current distribution network caused by the concurrent connection of electric vehicles.

Co-simulation Methodologies for Hybrid and Electric Vehicle Dynamics

In recent decades, full electric and hybrid electric vehicles have emerged as an alternative to conventional cars due to a range of factors, including environmental and economic aspects. These vehicles are the result of considerable efforts to seek ways of reducing the use of fossil fuel for vehicle propulsion. Sophisticated technologies such as hybrid and electric powertrains require careful study and optimization. Mathematical models play a key role at this point. Currently, many advanced mathematical analysis tools, as well as computer applications have been built for vehicle simulation purposes. Given the great interest of hybrid and electric powertrains, along with the increasing importance of reliable computer-based models, the author decided to integrate both aspects in the research purpose of this work. Furthermore, this is one of the first final degree projects held at the ETSII (Higher Technical School of Industrial Engineers) that covers the study of hybrid and electric propulsion systems. The present project is based on MBS3D 2.0, a specialized software for the dynamic simulation of multibody systems developed at the UPM Institute of Automobile Research (INSIA). Automobiles are a clear example of complex multibody systems, which are present in nearly every field of engineering. The work presented here benefits from the availability of MBS3D software. This program has proven to be a very efficient tool, with a highly developed underlying mathematical formulation. On this basis, the focus of this project is the extension of MBS3D features in order to be able to perform dynamic simulations of hybrid and electric vehicle models. This requires the joint simulation of the mechanical model of the vehicle, together with the model of the hybrid or electric powertrain. These sub-models belong to completely different physical domains. In fact the powertrain consists of energy storage systems, electrical machines and power electronics, connected to purely mechanical components (wheels, suspension, transmission, clutch…). The challenge today is to create a global vehicle model that is valid for computer simulation. Therefore, the main goal of this project is to apply co-simulation methodologies to a comprehensive model of an electric vehicle, where sub-models from different areas of engineering are coupled. The created electric vehicle (EV) model consists of a separately excited DC electric motor, a Li-ion battery pack, a DC/DC chopper converter and a multibody vehicle model. Co-simulation techniques allow car designers to simulate complex vehicle architectures and behaviors, which are usually difficult to implement in a real environment due to safety and/or economic reasons. In addition, multi-domain computational models help to detect the effects of different driving patterns and parameters and improve the models in a fast and effective way. Automotive designers can greatly benefit from a multidisciplinary approach of new hybrid and electric vehicles. In this case, the global electric vehicle model includes an electrical subsystem and a mechanical subsystem. The electrical subsystem consists of three basic components: electric motor, battery pack and power converter. A modular representation is used for building the dynamic model of the vehicle drivetrain. This means that every component of the drivetrain (submodule) is modeled separately and has its own general dynamic model, with clearly defined inputs and outputs. Then, all the particular submodules are assembled according to the drivetrain configuration and, in this way, the power flow across the components is completely determined. Dynamic models of electrical components are often based on equivalent circuits, where Kirchhoff’s voltage and current laws are applied to draw the algebraic and differential equations. Here, Randles circuit is used for dynamic modeling of the battery and the electric motor is modeled through the analysis of the equivalent circuit of a separately excited DC motor, where the power converter is included. The mechanical subsystem is defined by MBS3D equations. These equations consider the position, velocity and acceleration of all the bodies comprising the vehicle multibody system. MBS3D 2.0 is entirely written in MATLAB and the structure of the program has been thoroughly studied and understood by the author. MBS3D software is adapted according to the requirements of the applied co-simulation method. Some of the core functions are modified, such as integrator and graphics, and several auxiliary functions are added in order to compute the mathematical model of the electrical components. By coupling and co-simulating both subsystems, it is possible to evaluate the dynamic interaction among all the components of the drivetrain. ‘Tight-coupling’ method is used to cosimulate the sub-models. This approach integrates all subsystems simultaneously and the results of the integration are exchanged by function-call. This means that the integration is done jointly for the mechanical and the electrical subsystem, under a single integrator and then, the speed of integration is determined by the slower subsystem. Simulations are then used to show the performance of the developed EV model. However, this project focuses more on the validation of the computational and mathematical tool for electric and hybrid vehicle simulation. For this purpose, a detailed study and comparison of different integrators within the MATLAB environment is done. Consequently, the main efforts are directed towards the implementation of co-simulation techniques in MBS3D software. In this regard, it is not intended to create an extremely precise EV model in terms of real vehicle performance, although an acceptable level of accuracy is achieved. The gap between the EV model and the real system is filled, in a way, by introducing the gas and brake pedals input, which reflects the actual driver behavior. This input is included directly in the differential equations of the model, and determines the amount of current provided to the electric motor. For a separately excited DC motor, the rotor current is proportional to the traction torque delivered to the car wheels. Therefore, as it occurs in the case of real vehicle models, the propulsion torque in the mathematical model is controlled through acceleration and brake pedal commands. The designed transmission system also includes a reduction gear that adapts the torque coming for the motor drive and transfers it. The main contribution of this project is, therefore, the implementation of a new calculation path for the wheel torques, based on performance characteristics and outputs of the electric powertrain model. Originally, the wheel traction and braking torques were input to MBS3D through a vector directly computed by the user in a MATLAB script. Now, they are calculated as a function of the motor current which, in turn, depends on the current provided by the battery pack across the DC/DC chopper converter. The motor and battery currents and voltages are the solutions of the electrical ODE (Ordinary Differential Equation) system coupled to the multibody system. Simultaneously, the outputs of MBS3D model are the position, velocity and acceleration of the vehicle at all times. The motor shaft speed is computed from the output vehicle speed considering the wheel radius, the gear reduction ratio and the transmission efficiency. This motor shaft speed, somehow available from MBS3D model, is then introduced in the differential equations corresponding to the electrical subsystem. In this way, MBS3D and the electrical powertrain model are interconnected and both subsystems exchange values resulting as expected with tight-coupling approach.When programming mathematical models of complex systems, code optimization is a key step in the process. A way to improve the overall performance of the integration, making use of C/C++ as an alternative programming language, is described and implemented. Although this entails a higher computational burden, it leads to important advantages regarding cosimulation speed and stability. In order to do this, it is necessary to integrate MATLAB with another integrated development environment (IDE), where C/C++ code can be generated and executed. In this project, C/C++ files are programmed in Microsoft Visual Studio and the interface between both IDEs is created by building C/C++ MEX file functions. These programs contain functions or subroutines that can be dynamically linked and executed from MATLAB. This process achieves reductions in simulation time up to two orders of magnitude. The tests performed with different integrators, also reveal the stiff character of the differential equations corresponding to the electrical subsystem, and allow the improvement of the cosimulation process. When varying the parameters of the integration and/or the initial conditions of the problem, the solutions of the system of equations show better dynamic response and stability, depending on the integrator used. Several integrators, with variable and non-variable step-size, and for stiff and non-stiff problems are applied to the coupled ODE system. Then, the results are analyzed, compared and discussed. From all the above, the project can be divided into four main parts: 1. Creation of the equation-based electric vehicle model; 2. Programming, simulation and adjustment of the electric vehicle model; 3. Application of co-simulation methodologies to MBS3D and the electric powertrain subsystem; and 4. Code optimization and study of different integrators. Additionally, in order to deeply understand the context of the project, the first chapters include an introduction to basic vehicle dynamics, current classification of hybrid and electric vehicles and an explanation of the involved technologies such as brake energy regeneration, electric and non-electric propulsion systems for EVs and HEVs (hybrid electric vehicles) and their control strategies. Later, the problem of dynamic modeling of hybrid and electric vehicles is discussed. The integrated development environment and the simulation tool are also briefly described. The core chapters include an explanation of the major co-simulation methodologies and how they have been programmed and applied to the electric powertrain model together with the multibody system dynamic model. Finally, the last chapters summarize the main results and conclusions of the project and propose further research topics. In conclusion, co-simulation methodologies are applicable within the integrated development environments MATLAB and Visual Studio, and the simulation tool MBS3D 2.0, where equation-based models of multidisciplinary subsystems, consisting of mechanical and electrical components, are coupled and integrated in a very efficient way.

Geração de modelos de co-simulação distribuída para a arquitetura DCB

O aumento na complexidade dos sistemas embarcados, compostos por partes de hardware e software, aliado às pressões do mercado que exige novos produtos em prazos cada vez menores, tem levado projetistas a considerar a possibilidade de construir sistemas a partir da integração de componentes já existentes e previamente validados. Esses componentes podem ter sido desenvolvidos por diferentes equipes ou por terceiros e muitas vezes são projetados utilizando diferentes metodologias, linguagens e/ou níveis de abstração. Essa heterogeneidade torna complexo o processo de integração e validação de componentes, que normalmente é realizado através de simulação. O presente trabalho especifica mecanismos genéricos e extensíveis que oferecem suporte à cooperação entre componentes heterogêneos em um ambiente de simulação distribuída, sem impor padrões proprietários para formatos de dados e para a descrição do comportamento e interface dos componentes. Esses mecanismos são baseados na arquitetura DCB (Distributed Co-Simulation Backbone), voltada para co-simulação distribuída e heterogênea e inspirada nos conceitos de federado (componente de simulação) e federação (conjunto de componentes) que são definidos pelo HLA (High Level Architecture), um padrão de interoperabilidade para simulações distribuídas. Para dar suporte à co-simulação distribuída e heterogênea, esse trabalho descreve mecanismos que são responsáveis pelas tarefas de cooperação e distribuição, chamados de embaixadores, assim como o mecanismo gateway, que é responsável pela interoperabilidade entre linguagens e conversão de tipos de dados. Também é apresentada uma ferramenta de suporte à geração das interfaces de co-simulação, que são constituídas de dois embaixadores configuráveis e um gateway para cada federado, gerado a partir de templates pré-definidos.

Co-simulação distribuída de sistemas heterogêneos

Na simulação heterogênea de um sistema eletrônico complexo, um mesmo modelo pode ser composto por partes distintas em relação às tecnologias ou linguagens utilizadas na sua descrição, níveis de abstração, ou pela combinação de partes de software e de hardware (escopo da co-simulação). No uso de modelos heterogêneos, a construção de uma ponte eficaz entre diferentes simuladores, em conjunto com a solução de problemas tais como sincronização e tradução de dados, são alguns dos principais desafios. No contexto do projeto de sistemas embarcados, a validação desses sistemas via co-simulação está sujeita a estes desafios na medida em que um mesmo modelo de representação precisa suportar a cooperação consistente entre partes de hardware e de software. Estes problemas tornam-se mais significativos quando abordados em ambientes distribuídos, o que aumenta a complexidade dos mecanismos que gerenciam os ítens necessários à correta cooperação entre partes diferentes. Contudo, embora existam abordagens e ferramentas voltadas para o tratamento de modelos heterogêneos, inclusive em ambientes distribuídos, ainda persiste uma gama de limitações causadas pela distribuição e heterogeneidade de simuladores. Por exemplo, restrições quanto à variedade de tecnologias (ou linguagens) utilizadas na descrição das partes de um modelo, flexibilidade para o reuso de partes existentes, ou em tarefas de gerenciamento de sincronização/dados/interface/distribuição. Além disso, em geral, nas soluções existentes para simulação heterogênea, alterações são necessárias sobre as partes do modelo, limitando a preservação de sua integridade. Esta é uma característica indesejável, por exemplo, no reuso de componentes IP (Intellectual Property) Neste contexto, esta tese apresenta o DCB (Distributed Co-simulation Backbone), cujo propósito geral é o suporte à execução distribuída dos modelos heterogêneos. Para isso, são observados de modo integrado quatro fatores básicos: a distribuição física; a independência dos componentes (partes); o encapsulamento das estratégias de gerenciamento de tempo, de dados e de comunicação; e a sincronização híbrida. Em geral, as soluções existentes valorizam um fator em detrimento dos demais, dependendo dos propósitos envolvidos e sua variação em relação ao grau de especificidade (soluções proprietárias ou restritas a um escopo de aplicações). O Tangram, também discutido nesta tese em termos de requisitos, é uma proposta de ambiente para projeto de modelos heterogêneos distribuídos. No contexto da especificação do DCB, esta proposta tem como objetivo geral agregar num mesmo ambiente funcionalidades de apoio para a busca e catalogação de componentes, seguidas do suporte à construção e à execução distribuída de modelos heterogêneos via DCB. À luz dos princípios de generalidade e flexibilidade da arquitetura do DCB, o Tangram visa permitir que o projetista reduza seu envolvimento com detalhes relacionados ao provimento de condições necessárias à cooperação entre componentes heterogêneos. No escopo desta tese, ênfase foi dada à co-simulação de sistemas embarcados, ênfase esta observada também na construção do protótipo do Tangram/DCB, e nos estudos de caso. Contudo, a estrutura do DCB é apropriada para qualquer domínio onde a simulação possa ser utilizada como instrumento de validação, entre outros propósitos.

Co-simulazione e co-progetto non lineare/elettromagnetico di sistemi wireless non convenzionali

L’attività di ricerca contenuta in questa tesi si è concentrata nello sviluppo e nell’implementazione di tecniche per la co-simulazione e il co-progetto non lineare/elettromagnetico di sistemi wireless non convenzionali. Questo lavoro presenta un metodo rigoroso per considerare le interazioni tra due sistemi posti sia in condizioni di campo vicino che in condizioni di campo lontano. In sostanza, gli effetti del sistema trasmittente sono rappresentati da un generatore equivalente di Norton posto in parallelo all’antenna del sistema ricevente, calcolato per mezzo del teorema di reciprocità e del teorema di equivalenza. La correttezza del metodo è stata verificata per mezzo di simulazioni e misure, concordi tra loro. La stessa teoria, ampliata con l’introduzione degli effetti di scattering, è stata usata per valutare una condizione analoga, dove l’elemento trasmittente coincide con quello ricevente (DIE) contenuto all’interno di una struttura metallica (package). I risultati sono stati confrontati con i medesimi ottenibili tramite tecniche FEM e FDTD/FIT, che richiedono tempi di simulazione maggiori di un ordine di grandezza. Grazie ai metodi di co-simulazione non lineari/EM sopra esposti, è stato progettato e verificato un sistema di localizzazione e identificazione di oggetti taggati posti in ambiente indoor. Questo è stato ottenuto dotando il sistema di lettura, denominato RID (Remotely Identify and Detect), di funzioni di scansione angolare e della tecnica di RADAR mono-pulse. Il sistema sperimentale, creato con dispositivi low cost, opera a 2.5 GHz ed ha le dimensioni paragonabili ad un normale PDA. E’ stato sperimentata la capacità del RID di localizzare, in scenari indoor, oggetti statici e in movimento.

A framework for cyber-physical system simulation

In these last years, systems engineering has became one of the major research domains. The complexity of systems has increased constantly and nowadays Cyber-Physical Systems (CPS) are a category of particular interest: these, are systems composed by a cyber part (computer-based algorithms) that monitor and control some physical processes. Their development and simulation are both complex due to the importance of the interaction between the cyber and the physical entities: there are a lot of models written in different languages that need to exchange information among each other. Normally people use an orchestrator that takes care of the simulation of the models and the exchange of informations. This orchestrator is developed manually and this is a tedious and long work. Our proposition is to achieve to generate the orchestrator automatically through the use of Co-Modeling, i.e. by modeling the coordination. Before achieving this ultimate goal, it is important to understand the mechanisms and de facto standards that could be used in a co-modeling framework. So, I studied the use of a technology employed for co-simulation in the industry: FMI. In order to better understand the FMI standard, I realized an automatic export, in the FMI format, of the models realized in an existing software for discrete modeling: TimeSquare. I also developed a simple physical model in the existing open source openmodelica tool. Later, I started to understand how works an orchestrator, developing a simple one: this will be useful in future to generate an orchestrator automatically.

An algorithm for the inclusion of RC compact models of packages into board level thermal simulation tools

International audience

Architectural-Physical Co-Design of 3D CPUs with Micro-Fluidic Cooling

The performance, energy efficiency and cost improvements due to traditional technology scaling have begun to slow down and present diminishing returns. Underlying reasons for this trend include fundamental physical limits of transistor scaling, the growing significance of quantum effects as transistors shrink, and a growing mismatch between transistors and interconnects regarding size, speed and power. Continued Moore's Law scaling will not come from technology scaling alone, and must involve improvements to design tools and development of new disruptive technologies such as 3D integration. 3D integration presents potential improvements to interconnect power and delay by translating the routing problem into a third dimension, and facilitates transistor density scaling independent of technology node. Furthermore, 3D IC technology opens up a new architectural design space of heterogeneously-integrated high-bandwidth CPUs. Vertical integration promises to provide the CPU architectures of the future by integrating high performance processors with on-chip high-bandwidth memory systems and highly connected network-on-chip structures. Such techniques can overcome the well-known CPU performance bottlenecks referred to as memory and communication wall. However the promising improvements to performance and energy efficiency offered by 3D CPUs does not come without cost, both in the financial investments to develop the technology, and the increased complexity of design. Two main limitations to 3D IC technology have been heat removal and TSV reliability. Transistor stacking creates increases in power density, current density and thermal resistance in air cooled packages. Furthermore the technology introduces vertical through silicon vias (TSVs) that create new points of failure in the chip and require development of new BEOL technologies. Although these issues can be controlled to some extent using thermal-reliability aware physical and architectural 3D design techniques, high performance embedded cooling schemes, such as micro-fluidic (MF) cooling, are fundamentally necessary to unlock the true potential of 3D ICs. A new paradigm is being put forth which integrates the computational, electrical, physical, thermal and reliability views of a system. The unification of these diverse aspects of integrated circuits is called Co-Design. Independent design and optimization of each aspect leads to sub-optimal designs due to a lack of understanding of cross-domain interactions and their impacts on the feasibility region of the architectural design space. Co-Design enables optimization across layers with a multi-domain view and thus unlocks new high-performance and energy efficient configurations. Although the co-design paradigm is becoming increasingly necessary in all fields of IC design, it is even more critical in 3D ICs where, as we show, the inter-layer coupling and higher degree of connectivity between components exacerbates the interdependence between architectural parameters, physical design parameters and the multitude of metrics of interest to the designer (i.e. power, performance, temperature and reliability). In this dissertation we present a framework for multi-domain co-simulation and co-optimization of 3D CPU architectures with both air and MF cooling solutions. Finally we propose an approach for design space exploration and modeling within the new Co-Design paradigm, and discuss the possible avenues for improvement of this work in the future.

Intelligent mapping of stresses in a hydraulic crane

Continuous loading and unloading can cause breakdown of cranes. In seeking solution to this problem, the use of an intelligent control system for improving the fatigue life of cranes in the control of mechatronics has been under study since 1994. This research focuses on the use of neural networks as possibilities of developing algorithm to map stresses on a crane. The intelligent algorithm was designed to be a part of the system of a crane, the design process started with solid works, ANSYS and co-simulation using MSc Adams software which was incorporated in MATLAB-Simulink and finally MATLAB neural network (NN) for the optimization process. The flexibility of the boom accounted for the accuracy of the maximum stress results in the ADAMS model. The flexibility created in ANSYS produced more accurate results compared to the flexibility model in ADAMS/View using discrete link. The compatibility between.ADAMS and ANSYS softwares was paramount in the efficiency and the accuracy of the results. Von Mises stresses analysis was more suitable for this thesis work because the hydraulic boom was made from construction steel FE-510 of steel grade S355 with yield strength of 355MPa. Von Mises theory was good for further analysis due to ductility of the material and the repeated tensile and shear loading. Neural network predictions for the maximum stresses were then compared with the co-simulation results for accuracy, and the comparison showed that the results obtained from neural network model were sufficiently accurate in predicting the maximum stresses on the boom than co-simulation.

Control of multi-actuator system by an electrically driven hydraulic pump-motor

The awareness and concern of our environment together with legislation have set more and more tightening demands for energy efficiency of non-road mobile machinery (NRMM). Integrated electro-hydraulic energy converter (IEHEC) has been developed in Lappeenranta University of Technology (LUT). The elimination of resistance flow, and the recuperation of energy makes it very efficient alternative. The difficulties of IEHEC machine to step to the market has been the requirement of one IEHEC machine per one actuator. The idea is to switch IEHEC between two actuators of log crane using fast on/off valves. The control system architecture is introduced. The system has been simulated in co-simulation using two different software. The simulated responses of pump-controlled system is compared to the responses of the conventional valve-controlled system.

Simulateur compilé d’une description multi-langage des systèmes hétérogènes

La conception de systèmes hétérogènes exige deux étapes importantes, à savoir : la modélisation et la simulation. Habituellement, des simulateurs sont reliés et synchronisés en employant un bus de co-simulation. Les approches courantes ont beaucoup d’inconvénients : elles ne sont pas toujours adaptées aux environnements distribués, le temps d’exécution de simulation peut être très décevant, et chaque simulateur a son propre noyau de simulation. Nous proposons une nouvelle approche qui consiste au développement d’un simulateur compilé multi-langage où chaque modèle peut être décrit en employant différents langages de modélisation tel que SystemC, ESyS.Net ou autres. Chaque modèle contient généralement des modules et des moyens de communications entre eux. Les modules décrivent des fonctionnalités propres à un système souhaité. Leur description est réalisée en utilisant la programmation orientée objet et peut être décrite en utilisant une syntaxe que l’utilisateur aura choisie. Nous proposons ainsi une séparation entre le langage de modélisation et la simulation. Les modèles sont transformés en une même représentation interne qui pourrait être vue comme ensemble d’objets. Notre environnement compile les objets internes en produisant un code unifié au lieu d’utiliser plusieurs langages de modélisation qui ajoutent beaucoup de mécanismes de communications et des informations supplémentaires. Les optimisations peuvent inclure différents mécanismes tels que le regroupement des processus en un seul processus séquentiel tout en respectant la sémantique des modèles. Nous utiliserons deux niveaux d’abstraction soit le « register transfer level » (RTL) et le « transaction level modeling » (TLM). Le RTL permet une modélisation à bas niveau d’abstraction et la communication entre les modules se fait à l’aide de signaux et des signalisations. Le TLM est une modélisation d’une communication transactionnelle à un plus haut niveau d’abstraction. Notre objectif est de supporter ces deux types de simulation, mais en laissant à l’usager le choix du langage de modélisation. De même, nous proposons d’utiliser un seul noyau au lieu de plusieurs et d’enlever le bus de co-simulation pour accélérer le temps de simulation.