Evaluation of chemical tests for the quality of prawns

The object of this study was to determine the value of physical, bacteriological and chemical tests used to find out and compare the indices of quality of prawns stored at 0°C and at 18°C. pH value, nature of drip, the total bacterial count, presence or absence of tryptophan, trimethylamine content, glycogen, lactic acid, vitamins such as thiamin, riboflavin and niacin were estimated periodically to evaluate the quality of prawns stored at 0°C, whereas in addition to organoleptic changes, pH, bacterial count, nature of growth in peptone water, soluble protein in salt solution and loss of moisture, glycogen, lactic acid, and changes in vitamin B contents were noted periodically for prawns stored at -l8°C. Riboflavin and niacin were not affected appreciably but the retention of thiamin in prawns was very low.

Pilot study of the short-term physico-chemical stability of atenolol tablets stored in a multi-compartment compliance aid

Study objectives: There is a possibility that lower air, moisture and light protection could impact on physico-chemical stability of medicines inside multi-compartment compliance aids (MCCAs), although this has not yet been proved. The objectives of the study were to examine the physico-chemical stability of atenolol tablets stored in a compliance aid at room temperature, and at elevated temperature and humidity to simulate practice conditions. Methods: Atenolol 100 mg tablets in 28-chamber, plastic compliance aids with transparent lids were stored for four weeks at room temperature and at 40°C with 75% relative humidity. Tablets were also stored at room temperature in original packaging and Petri dishes. Physical tests were conducted to standards as laid down in the British Pharmacopoeia 2005, and dissolution to those of the United States Pharmacopoeia volume 24. Chemical stability was assessed by a validated high-performance liquid chromatography (HPLC) method. Results: Tablets at room temperature in original packaging, in compliance aids and Petri dishes remained the same in appearance and passed physico-chemical tests. Tablets exposed to 40°C with 75% relative humidity in compliance aids passed tests for uniformity of weight, friability and chemical stability but became pale and moist, softer (82 newtons ± 4; p< 0.0001) than tablets in the original packaging (118 newtons ± 6), more friable (0.14% loss of mass) compared with other tablets (0.005%), and failed the tests for disintegration (>15 minutes) and dissolution (only 15% atenolol released at 30 minutes). Conclusion: Although chemical stability was unaffected, storage in compliance aids at 40°C with 75% relative humidity softened atenolol tablets, prolonged disintegration time and hindered dissolution which could significantly reduce bioavailability. This formulation could be suitable for storage in compliance aids at 25°C, but not in hotter, humid weather.

Perchloric acid; authentic, scientific and practical considerations relative to its use as an important research and routine analytical chemical reagent with special reference to rapidity, accuracy and economy.

Mode of access: Internet.

Chemical solutions; reagents useful to the chemist, biologist, and bacteriologist,

"Literature references": p. 397-399. "Journal references": p. 401-404.

Wood properties and processing outcomes for plantation grown African mahogany (Khaya senegalensis) trees from Clare, Queensland (18 and 20 year-old trees) and Katherine, Northern Territory (14 year-old trees).

Khaya senegalensis, African mahogany, a high-value hardwood, was introduced in the Northern Territory (NT) in the 1950s; included in various trials there and at Weipa, Q in the 1960s-1970s; planted on ex mine sites at Weipa (160 ha) until 1985; revived in farm plantings in Queensland and in trials in the NT in the 1990s; adopted for large-scale, annual planting in the Douglas-Daly region, NT from 2006 and is to have the planted area in the NT extended to at least 20,000 ha. The recent serious interest from plantation growers, including Forest Enterprises Australia Ltd (FEA), has seen the establishment of some large scale commercial plantations. FEA initiated the current study to process relatively young plantation stands from both Northern Territory and Queensland plantations to investigate the sawn wood and veneer recovery and quality from trees ranging from 14 years (NT – 36 trees) to 18-20 years (North Queensland – 31 trees). Field measures of tree size and straightness were complemented with log end splitting assessment and cross-sectional disc sample collection for laboratory wood properties measurements including colour and shrinkage. End-splitting scores assessed on sawn logs were relatively low compared to fast grown plantation eucalypts and did not impact processing negatively. Heartwood proportion in individual trees ranged from 50% up to 92 % of butt cross-sectional disc area for the visually-assessed dark coloured central heartwood and lighter coloured transition wood combined. Dark central heartwood proportion was positively related to tree size (R2 = 0.57). Chemical tests failed to assist in determining heartwood – sapwood boundary. Mean basic density of whole disc samples was 658 kg/m3 and ranged among trees from 603 to 712 kg/m3. When freshly sawn, the heartwood of African mahogany was orange-red to red. Transition wood appeared to be pinkish and the sapwood was a pale yellow colour. Once air dried the heartwood colour generally darkens to pinkish-brown or orange-brown and the effect of prolonged time and sun exposure is to darken and change the heartwood to a red-brown colour. A portable colour measurement spectrophotometer was used to objectively assess colour variation in CIE L*, a* and b* values over time with drying and exposure to sunlight. Capacity to predict standard colour values accurately after varying periods of direct sunlight exposure using results obtained on initial air-dried surfaces decreased with increasing time to sun exposure. The predictions are more accurate for L* values which represent brightness than for variation in the a* values (red spectrum). Selection of superior breeding trees for colour is likely to be based on dried samples exposed to sunlight to reliably highlight wood colour differences. A generally low ratio between tangential and radial shrinkages was found, which was reflected in a low incidence of board distortion (particularly cupping) during drying. A preliminary experiment was carried out to investigate the quality of NIR models to predict shrinkage and density. NIR spectra correlated reasonably well with radial shrinkage and air dried density. When calibration models were applied to their validation sets, radial shrinkage was predicted to an accuracy of 76% with Standard Error of Prediction of 0.21%. There was also a strong predictive power for wood density. These are encouraging results suggesting that NIR spectroscopy has good potential to be used as a non-destructive method to predict shrinkage and wood density using 12mm diameter increment core samples. Average green off saw recovery was 49.5% (range 40 to 69%) for Burdekin Agricultural College (BAC) logs and 41.9% (range 20 to 61%) for Katherine (NT) logs. These figures are about 10% higher than compared to 30-year-old Khaya study by Armstrong et al. (2007) however they are inflated as the green boards were not docked to remove wane prior to being tallied. Of the recovered sawn, dried and dressed volume from the BAC logs, based on the cambial face of boards, 27% could potentially be used for select grade, 40% for medium feature grade and 26% for high feature grades. The heart faces had a slightly higher recovery of select (30%) and medium feature (43%) grade boards with a reduction in the volume of high feature (22%) and reject (6%) grade boards. Distribution of board grades for the NT site aged 14 years followed very similar trends to those of the BAC site boards with an average (between facial and cambial face) 27% could potentially be used for select grade, 42% for medium feature grade, 26% for high feature grade and 5% reject. Relatively to some other subtropical eucalypts, there was a low incidence of borer attack. The major grade limiting defects for both medium and high feature grade boards recovered from the BAC site were knots and wane. The presence of large knots may reflect both management practices and the nature of the genetic material at the site. This stand was not managed for timber production with a very late pruning implemented at about age 12 years. The large amount of wane affected boards is indicative of logs with a large taper and the presence of significant sweep. Wane, knots and skip were the major grade limiting defects for the NT site reflecting considerable amounts of sweep with large taper as might be expected in younger trees. The green veneer recovered from billets of seven Khaya trees rotary peeled on a spindleless lathe produced a recovery of 83% of green billet volume. Dried veneer recovery ranged from 40 to 74 % per billet with an average of 64%. All of the recovered grades were suitable for use in structural ply in accordance to AS/NZ 2269: 2008. The majority of veneer sheets recovered from all billets was C grade (27%) with 20% making D grade and 13% B grade. Total dry sliced veneer recovery from the logs of the two largest logs from each location was estimated to be 41.1%. Very positive results have been recorded in this small scale study. The amount of colour development observed and the very reasonable recoveries of both sawn and veneer products, with a good representation of higher grades in the product distribution, is encouraging. The prospects for significant improvement in these results from well managed and productive stands grown for high quality timber should be high. Additionally, the study has shown the utility of non-destructive evaluation techniques for use in tree improvement programs to improve the quality of future plantations. A few trees combined several of the traits desired of individuals for a first breeding population. Fortunately, the two most promising trees (32, 19) had already been selected for breeding on external traits, and grafts of them are established in the seed orchard.

Antioxidative long chain alkylresorcinols. Synthesis and deuterium labelling of bioactive compounds present in whole grains

The first synthesis of long chain 5-n-alkylresorcinols (C15-C25) in whole grains and whole grain products by a novel modification of Wittig reaction is described. 5-n-Alkylresorcinols are phenolic lipids that have various effects on biological systems, such as antioxidant activity and interaction with biological membranes. These compounds are considered as biomarkers of whole grain intake, which is connected with reduced risk of cardiovascular diseases and certain cancers. Novel hapten derivatives of 5-n-alkylresorcinols, potential compounds for immunoanalytical techniques, are prepared by the same procedure utilizing microwave catalysed aqueous Wittig reaction as the key step. The synthesised analogues are required by various analytical, metabolism and bioactivity investigations. Four alternative strategies for producing deuterium polylabelled 5-n-alkylresorcinols are explored. Ring-labelled D3-alkylresorcinols were synthesized by acidic H/D exchange. Side chain -labelled D4-derivative was prepared by a total synthesis approach utilizing D2 deuterogenation of a D2-alkene derivative, and deuterogenation of alkynes was investigated in another total synthesis approach. An -D3-labelled alkylresorcinol is isotopically pure and completely stable under all relevant conditions encountered during analytical work. The labelling of another phenolic component of whole grains was explored. The preparation of D3-ferulic acid and related compounds by way of selective methylation of the precursors is described. The deuterated compounds are useful as standards in the quantification of these natural products in various substances, such as food and human fluids. The pure 5-n-alkylresorcinol analogues prepared were used in in vitro experiments on alkylresorcinol antioxidant activity and antigenotoxicity. The in vitro experiments show that alkylresorcinols act as antioxidants, especially when incorporated into biological systems, but possess lower activity in chemical tests (FRAP and DPPH assay). Whole grain alkylresorcinols are shown for the first time to have a protective effect against copper induced oxidation of LDL, and H2O2 or genotoxic faecal water induced damage on HT29 cells.

Comparison of stabilised/solidified mixes of model drill cuttings based on the North Sea and Red Sea Areas

Following the global stringent legislations regulating the wastes generated from the drilling process of oil exploration and production activities, the management of hazardous drill cuttings has become one of the pressing needs confronting the petroleum industry. Most of the prevalent treatment techniques adopted by oil companies are extremely expensive and/or the treated product has to be landfilled without any potential end-use; thereby rendering these solutions unsustainable. The technique of stabilisation/solidification is being investigated in this research to treat drill cuttings prior to landfilling or for potential re-use in construction products. Two case studies were explored namely North Sea and Red Sea. Given the known difficulties with stabilising/solidifying oils and chlorides, this research made use of model drill cutting mixes based on typical drill cutting from the two case studies, which contained 4.2% and 10.95% average concentrations of hydrocarbons; and 2.03% and 2.13% of chlorides, by weight respectively. A number of different binders, including a range of conventional viz. Portland cement (PC) as well as less-conventional viz. zeolite, or waste binders viz. cement kiln dust (CKD), fly ash and compost were tested to assess their ability to treat the North Sea and Red Sea model drill cuttings. The dry binder content by weight was 10%, 20% and 30%. In addition, raw drill cuttings from one of the North Sea offshore rigs were stabilised/solidified using 30% PC. The characteristics of the final stabilised/solidified product were finally compared to those of thermally treated cuttings. The effectiveness of the treatment using the different binder systems was compared in the light of the aforementioned two contaminants only. A set of physical tests (unconfined compressive strength (UCS)), chemical tests (NRA leachability) and micro-structural examinations (using scanning electron microscopy (SEM), and X-ray diffraction (XRD)) were used to evaluate the relative performance of the different binder mixes in treating the drill cuttings. The results showed that the observed UCS covered a wide range of values indicating various feasible end-use scenarios for the treated cuttings within the construction industry. The teachability results showed the reduction of the model drill cuttings to a stable non-reactive hazardous waste, compliant with the UK acceptance criteria for non-hazardous landfills: (a) by most of the 30% and 20% binders for chloride concentrations, and (b) by the 20% and 30% of compost-PC and CKD-PC binders for the Red Sea cuttings. The 20% and 30% compost-PC and CKD-PC binders successfully reduced the leached oil concentration of the North Sea cuttings to inert levels. Copyright 2007, Society of Petroleum Engineers.

柴西南区下干柴沟组下段层序地层格架内沉积相展布及有利储集砂体分布研究

Lower member of the lower Ganchaigou Formation in the southwestern of Qaidam Basin is one of the main targeted exploration zones. With the advancement of exploration, the targets are gradually switching into the lithologic reservoirs and it is urgent to gain the more precise research results in distribution of sedimentary facies and sandstones. Guided by the theory of sequence stratigraphy and sedimentology as well as on the basis of many logging data, drillings, seismic data and chemical tests, the paper comprehensively analyzes the sedimentary facies and sandstones in the lower member of lower Ganchaigou Formation in the southern of Chaixi. According to the identification marks of the key interface in sequence stratigraphy, the key interfaces in lower member of lower Ganchaigou Formation in the southwestern of Qaidam Basin are identified as two third-order sequences SQ1、SQ2. By calibrating the synthetic seismogram, the seismic sequence, well drilling and logging sequences are united. Based on the works above, this paper chooses seven primary cross-sections and builds connecting-well stratigraphic correlation of seven main connecting-well sections. Ultimately, the high-resolution sequence stratigraphic frameworks in the lower member of the lower Ganchaigou Formation, which are uniform to logging and seismic data, are figured out. In terms of study on each sequence features, the main style of the base-level cycle overlay which forms the third-order sequence is confirmed. It contains asymmetric “becoming deep upward” style and symmetry style. Researching on the spreading characters of sequence stratigraphy indicates that SQ1 and SQ2 are rather thicker near northwest well Shashen 20 and Shaxin1 while they are quite thiner near Hongcan 1, Yuejin, Qie 4 and Dong8-Wu3, and the thickness of SQ1 is thicker than SQ2.Based on the deep analysis of the marks for depositional facies, it is proposed that the lake facies and braid river deltas facies mainly occurred in study areas. Besides, the sorts of sub-facies and micro-facies model are divided and described. Under the control of high-resolution sequence stratigraphic framework, three source directions from Arlarer Mountain、Qimantage Mountain and Dongchai Mountain are identified by using the features of heavy mineral assemblage and paleogeomorphy. In addition, regularities of distribution sedimentary facies in sequence stratigraphic framework are studied in accordance with research thinking of the "point" (single well) "line" (section) "face" (plane). In the stage of lower member in the lower Ganchaigou Formation in the southwestern of Qaidam Basin, it is at the early phrase of evolution of the lake basin with the gradual outspread and the rise of the lake level. Combined with physical analysis of reservoir sands formed in different sedimentary environment, the paper studies the style of favorable sandstone bodies that are underwater distributary channel of braided rive delta front, coarse sand in mouth bar and the sand body in sand flat of shore-shallow lacustrine facies. Finally, this article comprehensively analyzes the distribution relationship between sedimentary facies and favorable sandstone body and proposes the ideas that sequence SQ1 Yuejin area, well east 8-wu3 area, well qie4-qie1 area and well hongcan2 area are distributed areas of favorable sandstone.

Optimização energética de um sistema de climatização industrial

O desenvolvimento deste trabalho teve como objectivo a optimização de um sistema de climatização industrial, constituído por quatro centrais de climatização adiabáticas, que apresentam limitações de capacidade de arrefecimento, controlo e eficiência. Inicialmente foi necessária a pesquisa bibliográfica e recolha de informação relativa à indústria têxtil e ao processo de arrefecimento evaporativo. Numa fase posterior foram recolhidos e analisados os diversos dados essenciais à compreensão do binómio edifício/sistema de climatização, para a obtenção de possíveis hipóteses de optimização. Da fase de recolha de informações e dados, destaca-se, também, a realização de análises à qualidade do ar interior (QAI). As optimizações seleccionadas como passíveis de implementação, foram estudadas e analisadas com o auxílio do software de simulação energética dinâmica DesignBuilder e os resultados obtidos foram devidamente trabalhados e ajustados de modo a permitir uma assimilação amigável e de fácil interpretação das suas vantagens e desvantagens, tendo ainda sido objecto de estudo de viabilidade económica. A optimização proposta reflecte uma melhoria substancial das condições interiores ao nível da temperatura e humidade relativa, resultando, ainda assim, numa redução de consumos energéticos na ordem dos 23 % (490.337 kWh), isto é, uma poupança anual de 42.169 € aos custos de exploração e com um período de retorno de 1 ano e 11 meses.

FT-IR and MAS NMR analysis of montmorillonite K10 supported MF2 reagents and their activity as catalysis /

ZnF2, CdF2, and CUF2 have been adsorbed onto the surface of montmorillonite K10, and the infrared and 19F, 27 AI, and 29Si MAS NMR spectra of the reagents over a range of loadings have been obtained. CUF2 was observed to attack the Si02 layer and form the complex CuSiF6, Zn F2 tends to attack the aluminium oxide layer, in which Zn isomorphously replaces AI, and forms AIF3 and AIF4 - complexes. All the spectroscopic evidence ruled out the formation of any AI-F and/or Si-F free species as CdF2 is adsorbed on the surface of montmorillonite K10. The reactivity of MF2-K10 reagents towards Friedel-Crafts benzylation of benzene with benzyl chloride varied from one reagent to another. ZnF2-K10 was observed to be the most reactive and CUF2 was the least reactive.

A G. C./M. S. study of the reaction and decomposition products of pentafluorophenyl-grignard and lithium reagents

Decomposition and side reactions of, and the synthetic use of, pentafluorophenylmagnesium bromide and pentafluorophenyllithium have been investigated using G,C9/M.S, techniques• Their reactions with reagents such as CgF^X (X - H, F, CI, Br, 1), C6F4X2 (X - H, CI)f C6F3C13, C6H6. (CgX5)3P (X = H, F), (C6X5)3P=0 (X = H, F), (CgX5)Si (CH3)3 (X = H, F) and (CH0K SiCl , n = 1,2, in ether or ether/n-hexane were studied• In addition to the principal reaction of synthetic use, namely the replacement of a halogen by a pentafluorophenyl group, two types of side reactions were observed* These were (i) intermolecular loss of LiF via a nucleophilic substitution, and (ii) intramolecular loss of LiF, followed by the addition of either inorganic salts such as lithium or magnesium halides, or organometal compounds such as organolithium or organo-Grigaard* G.C«/M.S. techniques were routinely employed to study complicated reaction mixtures. Although mass spectrometry alone has disadvantages for the identification of isomers, deduction of the most probable pathway often helps overcome this problem.

Estudo da incorporação da cal em composições binárias de solo-cimento para produção de tijolos maciços

The use of binders in the soil for the production of solid bricks is an old construction technique that has been used by several civilizations over time. At the same time, the need for environmental preservation and the tendency of scarcity of natural resources make the construction invest in researching new concepts, methods and materials for building systems for the sustainability of their economic activities. Thus arises the need to obtain building materials with low power consumption, capable of reducing the growing housing shortage of rural and urban population. Currently, research has been conducted on this topic to better understand the cementitious and pozzolanic reactions that occur in the formation of the microstructure of the soil-cement when added to other materials such as, for example, lime, and the relationship between microstructure and formed interfaces with the physical, mechanical and chemical analysis in compounds made from these ternary compositions. In this context, this study aimed to analyze the results of the influence of the incorporation of lime to the soil-cement to form a ternary mixture to produce soil-cement bricks and mortar without structural purposes. From the inclusion of contents of 6 %, 8 %, 10% and 12% lime to the soil, and soil-cement mixes in amounts of 2 %, 3 %, 4 % and 5 % were shaped-bodies of -cylindrical specimens to determine the optimum moisture content and maximum dry apparent specific weight. Then they were cured, and subjected to the tests of compressive strength, absorption and durability modified. Compositions obtained the best results in the tests performed on the bodies-of-proof cylindrical served as a parameter for molding of solid bricks, which underwent the same experimental methodology previously cited. The raw materials used, as well as compositions in which the bricks were molded solid, were characterized by physical and chemical tests, X-ray diffraction and scanning electron microscopy. The results obtained in the study indicate that the compositions studied, that showed the best results in terms of compressive strength, water absorption and durability ternary composition was soil, 10 % cement and 2 % lime

Testes físico-mecânicos e físico-químicos do couro da tilápia vermelha

Realizaram-se testes físico-mecânicos e físico-químicos em couro de tilápia vermelha (Oreochromis spp.) a fim de testar a sua resistência. As amostras foram distribuídas em delineamento inteiramente ao acaso com dois tratamentos: no T1, procedeu-se à retirada do corpo-de-prova no sentido longitudinal e, no T2, à retirada do corpo-de-prova no sentido transversal. Para os testes de determinação da resistência à tração, alongamento e rasgamento progressivo, foi utilizado o dinamômetro EMIC, com velocidade de afastamento entre as cargas de 100 ± 20mm/min, em ambiente climatizado (± 23ºC e UR do ar de 50%), por 24 horas. A espessura do couro variou de 0,61 a 0,75mm, mas não houve diferença entre os sentidos analisados. O couro apresentou maior resistência à tração no sentido transversal, 25,89N/mm², (P<0,01), comparado ao sentido longitudinal, 14,20 N/mm². O alongamento foi significativamente (P<0,05) maior no sentido longitudinal, 80,8%, em relação ao transversal, 62,6%. Não houve diferença para o rasgamento progressivo entre os tratamentos. O couro apresentou teor de óxido de cromo de 3,8%, graxa de 15,1% e pH e cifra diferencial de 3,5 e 0,5, respectivamente. Os valores nos testes de resistência e físico-químicos apresentados pelo couro indicam que ele pode ser utilizado para a confecção de vestuário e artefatos de couro em geral.

Estudo de adulteração em méis brasileiros através de razão isotópica do carbono

Neste trabalho, objetivou-se analisar isotopicamente méis comercializados nas regiões Sul e Sudeste do Brasil, para a detecção de fraude. Foram colhidas amostras comerciais com registro no Serviço de Inspeção Federal, Estadual ou Municipal. As amostras foram submetidas à combustão no Analisador Elementar EA 1108 CHN e analisadas no espectrômetro de massas de razão isotópica DELTA-S (Finningan Mat). Os valores isotópicos (δ13C) dos méis in natura foram comparados aos de suas respectivas proteínas (padrão interno). Foram consideradas adulteradas as amostras cuja diferença entre o valor isotópico da proteína e do mel foi igual ou inferior a -1 . As amostras consideradas adulteradas pela análise isotópica foram submetidas a testes químicos qualitativos que não foram capazes de indicar adulteração para algumas delas. Das 61 amostras analisadas, 18,0% encontram-se adulteradas, sendo 11,5% na Região Sudeste e 6,5% na Região Sul. Ao contrário dos testes químicos, a análise isotópica mostrou-se eficaz em identificar e quantificar a adulteração de méis comerciais.