Recovery of organic acids with liquid-liquid extraction contactors

Liquid-liquid extraction is a mass transfer process for recovering the desired components from the liquid streams by contacting it to non-soluble liquid solvent. Literature part of this thesis deals with theory of the liquid-liquid extraction and the main steps of the extraction process design. The experimental part of this thesis investigates the extraction of organic acids from aqueous solution. The aim was to find the optimal solvent for recovering the organic acids from aqueous solutions. The other objective was to test the selected solvent in pilot scale with packed column and compare the effectiveness of the structured and the random packing, the effect of dispersed phase selection and the effect of packing material wettability properties. Experiments showed that selected solvent works well with dilute organic acid solutions. The random packing proved to be more efficient than the structured packing due to higher hold-up of the dispersed phase. Dispersing the phase that is present in larger volume proved to more efficient. With the random packing the material that was wetted by the dispersed phase was more efficient due to higher hold-up of the dispersed phase. According the literature, the behavior is usually opposite.

A comparison of the critical impeller speed for solids suspension in a bench-scale and a pilot-scale mechanical flotation cell

This paper compares the critical impeller speed results for 6 L Denver and Wemco bench-scale flotation cells with findings from a study by Van der Westhuizen and Deglon [Van der Westhuizen, A.P., Deglon, D.A., 2007. Evaluation of solids suspension in a pilot-scale mechanical flotation cell: the critical impeller speed. Minerals Engineering 20,233-240; Van der Westhuizen, A.P., Deglon, D.A., 2008. Solids suspension in a pilot scale mechanical flotation cell: a critical impeller speed correlation. Minerals Engineering 21, 621-629] conducted in a 125 L Batequip flotation cell. Understanding solids suspension has become increasingly important due to dramatic increases in flotation cell sizes. The critical impeller speed is commonly used to indicate the effectiveness of solids suspension. The minerals used in this study were apatite, quartz and hematite. The critical impeller speed was found to be strongly dependent on particle size, solids density and air flow rate, with solids concentration having a lesser influence. Liquid viscosity was found to have a negligible effect. The general Zwietering-type critical impeller speed correlation developed by Van der Westhuizen and Deglon [Van der Westhuizen, A.P., Deglon, D.A., 2008. Solids suspension in a pilot scale mechanical flotation cell: a critical impeller speed correlation. Minerals Engineering 21, 621-629] was found to be applicable to all three flotation machines. The exponents for particle size, solids concentration and liquid viscosity were equivalent for all three cells. The exponent for solids density was found to be less significant than that obtained by the previous authors, and to be consistent with values reported in the general literature for stirred tanks. Finally, a new dimensionless critical impeller speed correlation is proposed where the particle size is divided by the impeller diameter. This modified equation generally predicts the experimental measurements well, with most predictions within 10% of the experimental. (C) 2009 Elsevier Ltd. All rights reserved.

Detection and diagnosis solutions for fault-tolerant VSI

This paper presents solutions for fault detection and diagnosis of two-level, three phase voltage-source inverter (VSI) topologies with IGBT devices. The proposed solutions combine redundant standby VSI structures and contactors (or relays) to improve the fault-tolerant capabilities of power electronics in applications with safety requirements. The suitable combination of these elements gives the inverter the ability to maintain energy processing in the occurrence of several failure modes, including short-circuit in IGBT devices, thus extending its reliability and availability. A survey of previously developed fault-tolerant VSI structures and several aspects of failure modes, detection and isolation mechanisms within VSI is first discussed. Hardware solutions for the protection of power semiconductors with fault detection and diagnosis mechanisms are then proposed to provide conditions to isolate and replace damaged power devices (or branches) in real time. Experimental results from a prototype are included to validate the proposed solutions.

Elaboració de membranes de fibra buida modificades amb nanopartícules metàl·liques per aplicacions catalítiques

Investigación producida a partir de una estancia en la Université Paul Sabatier, Toulouse III - CNRS, entre 2007 y 2009. Durante los últimos años la investigación centrada en nuevos materiales de tamaño nanoscòpico (nanopartículas, quantum dots, nanotubos de carbono,...) ha experimentado un crecimiento considerable debido a las especiales propiedades de los "nanoobjetos" con respecto a magnetismo, catálisis, conductividad eléctrica, etc ... Sin embargo, hoy en día todavía existen pocas aplicaciones de las nanopartículas en temas medioambientales. Uno de los motivos de esta situación es la posible toxicidad de los nanoobjetos, pero existe también una dificultad tecnológica dado que las nanopartículas tienden a agregarse y es muy difícil manipularlas sin que pierdan sus propiedades especiales. Así, aunque la preparación de materiales catalíticos nanoestructurados es muy interesante, es necesario definir nuevas estrategias para prepararlos. Este proyecto de investigación tiene como objetivo principal la preparación de nuevas membranas catalíticas con nanopartículas metálicas en el interior para aplicaciones de tratamiento de agua. La innovación principal de este proyecto consiste en que las nanopartículas no son introducidas en la matriz polimérica una vez preformadas sino que se hacen crecer en el interior de la matriz polimérica mediante una síntesis intermatricial. El único requisito es que la matriz polimérica contenga grupos funcionales capaces de interaccionar con los precursores de las nanopartículas. Una vez finalizado el proyecto se puede afirmar que se han logrado parte de los objetivos planteados inicialmente. Concreamente ha quedado demostrado que se pueden sintetizar nanopartículas metálicas de metales nobles (platino y paladio) en membranas de fibra hueca de micro- y ultrafiltración siguiendo dos metodologías diferentes: modificación fotoquímica de polímeros y deposición de multicapas de polielectrolitos. Los nuevos materiales son efectivos en la catálisis de reducción de un compuesto modelo (4-nitrofenol con borohidruro de sodio) y, en general, los resultados han sido satisfactorios. Sin embargo, se ha puesto de manifiesto que el uso de un reactivo que genera hidrógeno gas en contacto con la solución acuosa dificulta enormemente la implementación de la reacción catalítica al ser el medio de la membrana una matriz porosa. Así, como conclusión principal se puede decir que se han encontrado las limitaciones de esta aproximación y se sugieren dos posibilidades de continuidad: la utilización de las membranas sintetizadas en contactores gas-líquido o bien el estudio y optimización del sistema de membrana en configuración de membranas planas, un objetivo más asequible dada su menor complejidad. Esta investigación se ha realizado en el seno del “Laboratoire de Génie Chimique” de Toulouse y del Departamento de Química de la Michigan State University y ha sido posible gracias a un proyecto financiado por la “Agence National pour la Recherce” y al programa PERMEANT entre el CNRS y la NSF.

Automatització d'una planta de preparació i distribució de pinsos

La finalitat del projecte és realitzar l’automatització dels sis processos d’una fàbrica de pinsos d’una cooperativa agrícola: entrada de matèries, mòlta, dosificació amb correcció, barreja, granulació i sortida de pinsos.Per controlar tots els processos es desenvolupa un PLC amb el corresponent programa d’autòmat; se seleccionen els diferents sensors i preactivadors necessaris que s’hauran d’incorporar per poder transformar la lògica rígida de contactors a una de flexible; se selecciona un sistema Scada per a la interfície d’usuari, i es dissenya la instal·lació elèctrica corresponent, per tal de poder implementar aquest automatisme en la línia de producció

Automatització d'una planta de preparació i distribució de pinsos

La finalitat del projecte és realitzar l’automatització dels sis processos d’una fàbrica de pinsos d’una cooperativa agrícola: entrada de matèries, mòlta, dosificació amb correcció, barreja, granulació i sortida de pinsos. Per controlar tots els processos es desenvolupa un PLC amb el corresponent programa d’autòmat; se seleccionen els diferents sensors i preactivadors necessaris que s’hauran d’incorporar per poder transformar la lògica rígida de contactors a una de flexible; se selecciona un sistema Scada per a la interfície d’usuari, i es dissenya la instal·lació elèctrica corresponent, per tal de poder implementar aquest automatisme en la línia de producció

An experimental approach to project risk identification and prioritization

One of the aims of a broad ethnographic study into how the apportionment of risk influences pricing levels of contactors was to ascertain the significant risks affecting contractors in Ghana, and their impact on prices. To do this, in the context of contractors, the difference between expected and realized return on a project is the key dependent variable examined using documentary analyses and semi-structured interviews. Most work in this has focused on identifying and prioritising risks using relative importance indices generated from the analysis of questionnaire survey responses. However, this approach may be argued to constitute perceptions rather than direct measures of the project risk. Here, instead, project risk is investigated by examining two measures of the same quantity; one ‘before’ and one ‘after’ construction of a project has taken place. Risks events are identified by ascertaining the independent variables causing deviations between expected and actual rates of return. Risk impact is then measured by ascertaining additions or reductions to expected costs due to the occurrence of risk events. So far, data from eight substantially complete building projects indicates that consultants’ inefficiency, payment delays, subcontractor-related problems and changes in macroeconomic factors are significant risks affecting contractors in Ghana.

Current collection by an active spherical electrode in an unmagnetized plasma

A theoretical model for the steady-state response of anodic contactors that emit a plasma current Ii and collect electrons from a collisionless, unmagnetized plasma is presented. The use of a (kinetic) monoenergetic population for the attracted species, well known in passive probe theory, gives both accuracy and tractability to the theory. The monoenergetic population is proved to behave like an isentropic fluid with radial plus centripetal motion, allowing direct comparisons with ad hoc fluid models. Also, a modification of the original monoenergetic equations permits analysis of contactors operating in orbit-limited conditions. Besides that, the theory predicts that, only for plasma emissions above certain threshold current a presheath/double layer/core structure for the potential is formed (the core mode), while for emissions below that threshold, a plasma contactor behaves exactly as a positive-ion emitter with a presheath/sheath structure (the no-core mode). Ion emitters are studied as a particular case. Emphasis is placed on obtaining dimensionless charts and approximate asymptotic laws of the current-voltage characteristic.

The radiation impedance of orbiting conductors

The dispersion relation for waves in a cold, magnetized plasma is discussed using the potential for the longitudinal part of the electric field. This clarifies wave emission from a conductor in low Earth orbit and should be useful in considering the far field and both hot plasma and nonlinear, near-field effects. General formulas for radiation impedance are directly obtained. For tethers a fundamental dependence on contactor size is discussed. Spherical and ellipsoidal contactors and an (anodcless) bare tether are considered. Simple arguments on nonlinear contactor effects lead to a surprisingly simple result for impedances off the Alfven branch.

A proposed two-stage two-tether scientific mission at Jupiter

A two-stage mission to place a spacecraft (SC) below the Jovian radiation belts, using a spinning bare tether with plasma contactors at both ends to provide propulsion and power,is proposed. Capture by Lorentz drag on the tether, at the periapsis of a barely hyperbolic equatorial orbit, is followed by a sequence of orbits at near-constant periapsis, drag finally bringing the SC down to a circular orbit below the halo ring. Although increasing both tether heating and bowing, retrograde motion can substantially reduce accumulated dose as compared with prograde motion, at equal tether-to-SC mass ratio. In the second stage,the tether is cut to a segment one order of magnitude smaller, with a single plasma contactor, making the SC to slowly spiral inward over severalmonths while generating large onboard power, which would allow multiple scientific applications, including in situ study of Jovian grains, auroral sounding of upper atmosphere, and space- and time-resolved observations of surface and subsurface.

The radiation impedance of electrodynamics tethers in a polar Jovian orbit

Juno, the second mission in the NASA New Frontiers Program, will both be a polar Jovian orbiter, and use solar arrays for power, moving away from previous use of radioisotope power systems (RPSs) in spite of the weak solar light reaching Jupiter. The power generation at Jupiter is critical, and a conductive tether could be an alternative source of power. A current-carrying tether orbiting in a magnetized ionosphere/plasmasphere will radiate waves. A magnitude of interest for both power generation and signal emission is the wave impedance. Jupiter has the strongest magnetic field in the Solar Planetary System and its plasma density is low everywhere. This leads to an electron plasma frequency smaller than the electron cyclotron frequency, and a high Alfven velocity. Unlike the low Earth orbit (LEO) case, the electron skin depth and the characteristic size of plasma contactors affect the Alfven impedance.