Fracture Resistance of the Implant-Abutment Connection in Implants with Internal Hex and Internal Conical Connections Under Oblique Compressive Loading: An In Vitro Study

The objective of this study was to verify if differences in the design of internal hex (IH) and internal conical (IC) connection implant systems influence fracture resistance under oblique compressive forces. Twenty implant-abutment assemblies were utilized: 10 with IH connections and 10 with IC connections. Maximum deformation force for IC implants (90.58 +/- 6.72 kgf) was statistically higher than that for IH implants (83.73 +/- 4.94 kgf) (P = .0182). Fracture force for the IH implants was 79.86 +/- 4.77 kgf. None of the IC implants fractured. The friction-locking mechanics and the solid design of the IC abutments provided greater resistance to deformation and fracture under oblique compressive loading when compared to the IH abutments. Int J Prosthodont 2009;22:283-286.

Adaptable Strut-and-Tie Model for Design and Verification of Four-Pile Caps

A large percentage of pile caps support only one column, and the pile caps in turn are supported by only a few piles. These are typically short and deep members with overall span-depth ratios of less than 1.5. Codes of practice do not provide uniform treatment for the design of these types of pile caps. These members have traditionally been designed as beams spanning between piles with the depth selected to avoid shear failures and the amount of longitudinal reinforcement selected to provide sufficient flexural capacity as calculated by the engineering beam theory. More recently, the strut-and-tie method has been used for the design of pile caps (disturbed or D-region) in which the load path is envisaged to be a three-dimensional truss, with compressive forces being supported by concrete compressive struts between the column and piles and tensile forces being carried by reinforcing steel located between piles. Both of these models have not provided uniform factors of safety against failure or been able to predict whether failure will occur by flexure (ductile mode) or shear (fragile mode). In this paper, an analytical model based on the strut-and-tie approach is presented. The proposed model has been calibrated using an extensive experimental database of pile caps subjected to compression and evaluated analytically for more complex loading conditions. It has been proven to be applicable across a broad range of test data and can predict the failures modes, cracking, yielding, and failure loads of four-pile caps with reasonable accuracy.

Efetividade da reeducação postural global no tratamento de um caso de lombociatalgia de origem discal

A Reeducação Postural Global (RPG) é um método que promove o alongamento da musculatura estática (tónica), incluindo a intervertebral, que está constantemente em contração, originando grandes forças compressivas sobre o disco intervertebral. Apesar de ser uma modalidade de tratamento muito utilizada, existem poucos estudos que suportem a sua base teórica e a sua efetividade clínica. Objetivo: Avaliar a efetividade do método de RPG no tratamento de um caso de lombociatalgia de origem discal. Métodos: Estudo de caso clínico de um professor de 56 anos de idade, com sintomas de hérnia discal lombar no nível de L4-L5, associada a uma anterolistesis de L5, confirmada por Ressonância Magnética. A avaliação e tratamento centrou-se no método de RPG realizado ao longo de duas sessões. Na primeira sessão foi utilizada uma postura de abertura de coxofemoral em decúbito durante 30 minutos, enquanto que na segunda foi utilizada inicialmente essa postura durante 20 minutos, seguida de uma postura em fechamento de coxofemoral em carga durante 15 minutos. Foram analisados os dados relativos à avaliação postural (inspecção visual), à dor (Escala Visual Analógica), à força muscular dos peroniais e extensores dos dedos (Teste Muscular Manual), à presença de formigueiro e ao reflexo aquiliano antes e depois de cada uma das sessões. Resultados: No final das duas sessões, verificaram-se alterações na avaliação postural, principalmente com a diminuição da hiperlordose lombar e da retroversão dos ilíacos, normalização do reflexo aquiliano e da força muscular, diminuição da sensação de formigueiro e desaparecimento total da dor. Conclusão: Os resultados obtidos neste estudo sugerem que a Reeducação Postural Global foi efectiva no tratamento de um caso de lombociatalgia com origem numa hérnia discal lombar.

Soft biomaterials as a substitute for the Nucleus Pulposus

One of the largest health problems faced worldwide, when evaluated by direct (clinical) as well indirect cost (absenteeism), is the degeneration of the intervertebral disc (IVD) that leads to back pain and, potentially disability and individual´s quality of life decreasing. The intervertebral disc is a mechanical and biological complex structure, formed by a tough outer layer of fibrocartilage called Annulus Fibrosus (AF),which surrounds a soft, elastic and gelatinous core called Nucleus Pulposus (NP). These two structures are completed by two upper and lower encasing layer called Vertebral Endplates (VEP). The degeneration of the IVD is marked by the dehydration of the Nucleus Pulposus, reducing the hydrostatic pressure inside the nucleus, resulting in a loss of capability to support compressive forces, during the active period, and to regain height during the resting period. This situation will compromise the role of shock absorber by the NP and transfers these forces to the AF. This transfer will result in cracks on the AF, deteriorating the IVD, allowing the ingrowth of vessels and nerves. This project was based on the developing a protocol to test suitable NP replacements, in hope to future assessment of discrete mechanical values and characteristics for an NP replacement. For this, Nucleus pulposus samples from goat, encapsulated Hydromed gel denominated “Raviolis” and Chitosan gels, produced via wet route using an ammonium environment, were confined compressed. Chitosan was rheologically tested and swelling capability of all the three type of materials was assessed. Results showed that the Nucleus Pulposus and “Raviolis” have similar mechanical behavior, being able to swell and “build up” hydrostatic pressure after a compression stage, while the Chitosan gel did not showed that ability. Therefore, “Raviolis” are a more suitable candidate to replace the NP than Chitosan gels. It was also observed that confined compression is the key test to perform on any possible candidate to replace the NP.

Estudo e caracterização mecânica por via experimental de modelos de subestruturas eletromecânicas aplicadas ao fabrico de transformadores de grande potência

Dissertação de mestrado integrado em Engenharia Mecânica

Estudo numérico sobre o reforço de pilares de betão armado com cantoneiras e presilhas metálicas: análise paramétrica e modelo de cálculo

Dissertação de mestrado integrado em Engenharia Civil

Experimental insights into deformation dynamics and intermittency in rapid granular shear flows

This work concerns the experimental study of rapid granular shear flows in annular Couette geometry. The flow is induced by continuous driving of the horizontal plate at the top of the granular bed in an annulus. The compressive pressure, driving torque, instantaneous bed height and rotational speed of the shearing plate are measured. Moreover, local stress fluctuations are measured in a medium made of steel spheres 2 and 3 mm in diameter. Both monodisperse packing and bidisperse packing are investigated to reveal the influence of size diversity in intermittent features of granular materials. Experiments are conducted in an annulus that can contain up to 15 kg of spherical steel balls. The shearing granular medium takes place via the rotation of the upper plate which compresses the material loaded inside the annulus. Fluctuations of compressive force are locally measured at the bottom of the annulus using a piezoelectric sensor. Rapid shear flow experiments are pursued at different compressive forces and shear rates and the sensitivity of fluctuations are then investigated by different means through monodisperse and bidisperse packings. Another important feature of rapid granular shear flows is the formation of ordered structures upon shearing. It requires a certain range for the amount of granular material (uniform size distribution) loaded in the system in order to obtain stable flows. This is studied more deeply in this thesis. The results of the current work bring some new insights into deformation dynamics and intermittency in rapid granular shear flows. The experimental apparatus is modified in comparison to earlier investigations. The measurements produce data for various quantities continuously sampled from the start of shearing to the end. Static failure and dynamic shearing ofa granular medium is investigated. The results of this work revealed some important features of failure dynamics and structure formation in the system. Furthermore, some computer simulations are performed in a 2D annulus to examine the nature of kinetic energy dissipation. It is found that turbulent flow models can statistically represent rapid granular flows with high accuracy. In addition to academic outcomes and scientific publications our results have a number of technological applications associated with grinding, mining and massive grain storages.

Modelo de comportamiento en sevicio para estructuras reticulares de hormigón. Parte II: Diagrama tensión- deformación para elementos fisurados a flexión

This paper presents a general methodology to adjust the coefficients defining a constitutive law for tensioned concrete to simulate, under serviceability conditions, the behaviour of cracked concrete members subjected to simple and combined bending (with axial compressive forces). Although experimental results could be used to obtain the mentioned objective, in this work the models proposed by the CEB are utilized, in order to obtain more general conclusions not subjected to specific experiments. A numerical parametrical analysis is performed to determine the more significant variables influencing the Tension-Stiffening effect and simplified closed-form solution is derived for rectangular sections. A systematic study has been to verify the ability of the method to simulate long-term effects. The methodology can be implemented as an initial process in a general model of analysis like the one presented in Part I

Influence de la locomotion sur la morphologie de l’articulation distale de l’humérus chez les hominoïdes

La masse corporelle et la direction des charges sont des facteurs qui peuvent modifier la morphologie des surfaces articulaires qui sont généralement orientées et de taille suffisante pour résister aux charges chroniques. Chez les hominoïdes, les forces de tension et compression, générées par la locomotion, sont transmises à travers l’articulation du coude. Ces espèces ont une morphologie similaire de l’extrémité distale de l’humérus, mais qui présente certaines différences selon la taille des individus et leurs modes de locomotion. Ce projet tente de caractériser plus exhaustivement cette variation en analysant la largeur des surfaces articulaires ainsi que leur position et orientation par rapport à l’axe long de la diaphyse. La prémisse de ce mémoire est que, chez les espèces plus arboricoles, la morphologie de l’articulation distale de l’humérus répond aux stress transverses générés par les puissants muscles fléchisseurs du poignet et des doigts qui traversent le coude obliquement. En revanche, les espèces plus terrestres présentent une morphologie permettant de résister aux forces axiales provenant du contact avec le sol. Des coordonnées tridimensionnelles et des mesures linéaires ont été recueillies sur un échantillon squelettique d’individus des genres Homo, Pan, Gorilla et Pongo. Les résultats obtenus révèlent que l’orientation et la position des surfaces articulaires de la trochlée correspondent aux types de locomotion, or leur taille et celle et du capitulum semblent être influencées par la taille des individus. L’hypothèse suggérant que les stress reliés aux divers modes de locomotion des hominoïdes influencent la morphologie de l’articulation distale de l’humérus est donc supportée.

Ectopic mineralization of articular cartilage in the bullfrog Rana catesbeiana and its possible involvement in bone closure

Mineralization of the articular cartilage is a pathological condition associated with age and certain joint diseases in humans and other mammals. In this work, we describe a physiological process of articular cartilage mineralization in bullfrogs. Articular cartilage of the proximal and distal ends of the femur and of the proximal end of the tibia-fibula was studied in animals of different ages. Mineralization of the articular cartilage was detected in animals at 1 month post-transformation. This mineralization, which appeared before the hypertrophic cartilage showed any calcium deposition, began at a restricted site in the lateral expansion of the cartilage and then progressed to other areas of the epiphyseal cartilage. Mineralized structures were identified by von Kossa's staining and by in vivo incorporation of calcein green. Element analysis showed that calcium crystals consisted of poorly crystalline hydroxyapatite. Mineralized matrix was initially spherical structures that generally coalesced after a certain size to occupy larger areas of the cartilage. Alkaline phosphatase activity was detected at the plasma membrane of nearby chondrocytes and in extracellular matrix. Apoptosis was detected by the TUNEL (TDT-mediated dUTP-biotin nick end-labeling) reaction in some articular chondrocytes from mineralized areas. The area occupied by calcium crystals increased significantly in older animals, especially in areas under compression. Ultrastructural analyses showed clusters of needle-like crystals in the extracellular matrix around the chondrocytes and large blocks of mineralized matrix. In 4-year-old animals, some lamellar bone (containing bone marrow) occurred in the same area as articular cartilage mineralization. These results show that the articular cartilage of R. catesbeiana undergoes precocious and progressive mineralization that is apparently stimulated by compressive forces. We suggest that this mineralization is involved in the closure of bone extremities, since mineralization appears to precede the formation of a rudimentary secondary center of ossification in older animals.

MICROFIBRILS - NEGLECTED COMPONENTS OF PRESSURE-BEARING TENDONS

Some tendons wrap around joints and receive compressive forces besides transferring the tension forces from muscle to bone. These tendons develop a fibrocartilaginous structure which enables them to withstand pressure. This article describes the existence and distribution of microfibrils (or preelastic fibers) in the pressure-bearing tendons of rabbits and dogs by the application of histochemical assays and transmission electron microscopy. Rabbit and dog tendons possess no mature elastic fibers. The rabbit tendon exhibits some response to Weigert's method prior to oxidation which indicates the existence of the so-called elaunin fibers, especially in the pressure zone. Oxidation with peracetic acid or oxone discloses intricate aspects of the oxytalan fiber distribution in both tension and pressure zones of the dog and rabbit tendons. Bundles of 12 nm microfibrils were demonstrated in the rabbit tendon by electron microscopy after fixation in the presence of tannic acid. The existence of preelastic fibers in the pressure-bearing tendons has been neglected and they are assumed to have importance in the microarchitecture of the tissue and in the ability of the tendon to support tension and compression forces.

Análise estrutural de tubos de concreto armado com resíduo de borracha de pneu

Pós-graduação em Engenharia Civil - FEIS

Attenuation of foot pressure during running on four different surfaces: asphalt, concrete, rubber, and natural grass

The practice of running has consistently increased worldwide, and with it, related lower limb injuries. The type of running surface has been associated with running injury etiology, in addition other factors, such as the relationship between the amount and intensity of training. There is still controversy in the literature regarding the biomechanical effects of different types of running surfaces on foot-floor interaction. The aim of this study was to investigate the influence of running on asphalt, concrete, natural grass, and rubber on in-shoe pressure patterns in adult recreational runners. Forty-seven adult recreational runners ran twice for 40 m on all four different surfaces at 12 +/- 5% km . h(-1). Peak pressure, pressure-time integral, and contact time were recorded by Pedar X insoles. Asphalt and concrete were similar for all plantar variables and pressure zones. Running on grass produced peak pressures 9.3% to 16.6% lower (P < 0.001) than the other surfaces in the rearfoot and 4.7% to 12.3% (P < 0.05) lower in the forefoot. The contact time on rubber was greater than on concrete for the rearfoot and midfoot. The behaviour of rubber was similar to that obtained for the rigid surfaces - concrete and asphalt - possibly because of its time of usage (five years). Running on natural grass attenuates in-shoe plantar pressures in recreational runners. If a runner controls the amount and intensity of practice, running on grass may reduce the total stress on the musculoskeletal system compared with the total musculoskeletal stress when running on more rigid surfaces, such as asphalt and concrete.

Solid-State Compatibilization of Immiscible Polymer Blends: Cryogenic Milling and Solid-State Shear Pulverization

The blending of common polymers allows for the rapid and facile synthesis of new materials with highly tunable properties at a fraction of the costs of new monomer development and synthesis. Most blends of polymers, however, are completely immiscible and separate into distinct phases with minimal phase interaction, severelydegrading the performance of the material. Cross-phase interactions and property enhancement can be achieved with these blends through reactive processing or compatibilizer addition. A new class of blend compatibilization relies on the mechanochemical reactions between polymer chains via solid-state, high energy processing. Two contrasting mechanochemical processing techniques are explored in this thesis: cryogenic milling and solid-state shear pulverization (SSSP). Cryogenic milling is a batch process where a milling rod rapidly impacts the blend sample while submerged within a bath of liquid nitrogen. In contrast, SSSP is a continuous process where blend components are subjected to high shear and compressive forces while progressing down a chilled twin-screw barrel. In the cryogenic milling study, through the application of a synthesized labeledpolymer, in situ formation of copolymers was observed for the first time. The microstructures of polystyrene/high-density polyethylene (PS/HDPE) blends fabricated via cryomilling followed by intimate melt-state mixing and static annealing were found to be morphologically stable over time. PS/HDPE blends fabricated via SSSP also showed compatibilization by way of ideal blend morphology through growth mechanisms with slightly different behavior compared to the cryomilled blends. The new Bucknell University SSSP instrument was carefully analyzed and optimized to produce compatibilized polymer blends through a full-factorial experiment. Finally, blends of varying levels of compatibilization were subjected to common material tests to determine alternative means of measuring and quantifying compatibilization,

Ligament balancing in TKA: Evaluation of a force-sensing device and the influence of patellar eversion and ligament release

Ligament balancing in total knee arthroplasty may have an important influence on joint stability and prosthesis lifetime. In order to provide quantitative information and assistance during ligament balancing, a device that intraoperatively measures knee joint forces and moments was developed. Its performance and surgical advantages were evaluated on six cadaver specimens mounted on a knee joint loading apparatus allowing unconstrained knee motion as well as compression and varus-valgus loading. Four different experiments were performed on each specimen. (1) Knee joints were axially loaded. Comparison between applied and measured compressive forces demonstrated the accuracy and reliability of in situ measurements (1.8N). (2) Assessment of knee stability based on condyle contact forces or varus-valgus moments were compared to the current surgical method (difference of varus-valgus loads causing condyle lift-off). The force-based approach was equivalent to the surgical method while the moment-based, which is considered optimal, showed a tendency of lateral imbalance. (3) To estimate the importance of keeping the patella in its anatomical position during imbalance assessment, the effect of patellar eversion on the mediolateral distribution of tibiofemoral contact forces was measured. One fourth of the contact force induced by the patellar load was shifted to the lateral compartment. (4) The effect of minor and major medial collateral ligament releases was biomechanically quantified. On average, the medial contact force was reduced by 20% and 46%, respectively. Large variation among specimens reflected the difficulty of ligament release and the need for intraoperative force monitoring. This series of experiments thus demonstrated the device's potential to improve ligament balancing and survivorship of total knee arthroplasty.