Variance dispersion graphs for comparing blocked response surface designs

In this paper, we extend the use of the variance dispersion graph (VDG) to experiments in which the response surface (RS) design must be blocked. Through several examples we evaluate the prediction performances of RS designs in non-orthogonal block designs compared with the equivalent unblocked designs and orthogonally blocked designs. These examples illustrate that good prediction performance of designs in small blocks can be expected in practice. Most importantly, we show that the allocation of the treatment set to blocks can seriously affect the prediction properties of designs; thus, much care is needed in performing this allocation.

Spray Congealing of Pharmaceuticals: Study on Production of Solid Dispersions Using Box-Behnken Design

This work aimed at evaluating the spray congealing method for the production of microparticles of carbamazepine combined with a polyoxylglyceride carrier. In addition, the influence of the spray congealing conditions on the improvement of drug solubility was investigated using a three-factor, three-level Box-Behnken design. The factors studied were the cooling air flow rate, atomizing pressure, and molten dispersion feed rate. Dependent variables were the yield, solubility, encapsulation efficiency, particle size, water activity, and flow properties. Statistical analysis showed that only the yield was affected by the factors studied. The characteristics of the microparticles were evaluated using X-ray powder diffraction, scanning electron microscopy, differential scanning calorimetry, and hot-stage microscopy. The results showed a spherical morphology and changes in the crystalline state of the drug. The microparticles were obtained with good yields and encapsulation efficiencies, which ranged from 50 to 80% and 99.5 to 112%, respectively. The average size of the microparticles ranged from 17.7 to 39.4 mu m, the water activities were always below 0.5, and flowability was good to moderate. Both the solubility and dissolution rate of carbamazepine from the spray congealed microparticles were remarkably improved. The carbamazepine solubility showed a threefold increase and dissolution profile showed a twofold increase after 60 min compared to the raw drug. The Box-Behnken fractional factorial design proved to be a powerful tool to identify the best conditions for the manufacture of solid dispersion microparticles by spray congealing.

Estudo da deposição de filmes finos de BaTi(1-X)Zr(X)O3 por meio de planejamento Box-Behnken

Ferroelectric ceramics with perovskite structure (ABO3) are widely used in solid state memories (FeRAM’s and DRAM's) as well as multilayered capacitors, especially as a thin films. When doped with zirconium ions, BaTiO3-based materials form a solid solution known as barium zirconate titanate (BaTi1-xZrxO3). Also called BZT, this material can undergo significant changes in their electrical properties for a small variation of zirconium content in the crystal lattice. The present work is the study of the effects of deposition parameters of BaTi0,75Zr0,25O3 thin films by spin-coating method on their morphology and physical properties, through an experimental design of the Box-Behnken type. The resin used in the process has been synthesized by the polymeric precursor method (Pechini) and subsequently split into three portions each of which has its viscosity adjusted to 10, 20 and 30 mPa∙s by means of a rotary viscometer. The resins were then deposited on Pt/Ti/SiO2/Si substrates by spin-coating method on 15 different combinations of viscosity, spin speed (3000, 5500 and 8000 rpm) and the number of deposited layers (5, 8 and 11 layers) and then calcined at 800 ° C for 1 h. The phase composition of the films was analyzed by X-ray diffraction (XRD) and indexed with the JCPDS 36-0019. Surface morphology and grain size were observed by atomic force microscopy (AFM) indicating uniform films and average grain size around 40 nm. Images of the cross section of the films were obtained by scanning electron microscopy field emission (SEM-FEG), indicating very uniform thicknesses ranging from 140-700 nm between samples. Capacitance measurements were performed at room temperature using an impedance analyzer. The films presented dielectric constant values of 55-305 at 100kHz and low dielectric loss. The design indicated no significant interaction effects between the deposition parameters on the thickness of the films. The response surface methodology enabled better observes the simultaneous effect of variables.

Development and optimization of fluoxetine orally disintegrating tablets using Box-Behnken design

Purpose: To develop and optimise some variables that influence fluoxetine orally disintegrating tablets (ODTs) formulation. Methods: Fluoxetine ODTs tablets were prepared using direct compression method. Three-factor, 3- level Box-Behnken design was used to optimize and develop fluoxetine ODT formulation. The design suggested 15 formulations of different lubricant concentration (X1), lubricant mixing time (X2), and compression force (X3) and then their effect was monitored on tablet weight (Y1), thickness (Y2), hardness (Y3), % friability (Y4), and disintegration time (Y5). Results: All powder blends showed acceptable flow properties, ranging from good to excellent. The disintegration time (Y5) was affected directly by lubricant concentration (X1). Lubricant mixing time (X2) had a direct effect on tablet thickness (Y2) and hardness (Y3), while compression force (X3) had a direct impact on tablet hardness (Y3), % friability (Y4) and disintegration time (Y5). Accordingly, Box-Behnken design suggested an optimized formula of 0.86 mg (X1), 15.3 min (X2), and 10.6 KN (X3). Finally, the prediction error percentage responses of Y1, Y2, Y3, Y4, and Y5 were 0.31, 0.52, 2.13, 3.92 and 3.75 %, respectively. Formula 4 and 8 achieved 90 % of drug release within the first 5 min of dissolution test. Conclusion: Fluoxetine ODT formulation has been developed and optimized successfully using Box- Behnken design and has also been manufactured efficiently using direct compression technique.

An algorithm for arranging response surface designs in small blocks

We consider the problem of blocking response surface designs when the block sizes are prespecified to control variation efficiently and the treatment set is chosen independently of the block structure. We show how the loss of information due to blocking is related to scores defined by Mead and present an interchange algorithm based on scores to improve a given blocked design. Examples illustrating the performance of the algorithm are given and some comparisons with other designs are made. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Difference variance dispersion graphs for comparing response surface designs with applications in food technology

Variance dispersion graphs have become a popular tool in aiding the choice of a response surface design. Often differences in response from some particular point, such as the expected position of the optimum or standard operating conditions, are more important than the response itself. We describe two examples from food technology. In the first, an experiment was conducted to find the levels of three factors which optimized the yield of valuable products enzymatically synthesized from sugars and to discover how the yield changed as the levels of the factors were changed from the optimum. In the second example, an experiment was conducted on a mixing process for pastry dough to discover how three factors affected a number of properties of the pastry, with a view to using these factors to control the process. We introduce the difference variance dispersion graph (DVDG) to help in the choice of a design in these circumstances. The DVDG for blocked designs is developed and the examples are used to show how the DVDG can be used in practice. In both examples a design was chosen by using the DVDG, as well as other properties, and the experiments were conducted and produced results that were useful to the experimenters. In both cases the conclusions were drawn partly by comparing responses at different points on the response surface.

Biodiesel production from non-edible beauty leaf (Calophyllum Inophyllum) oil : process optimization using response surface methodology (RSM)

In recent years, the beauty leaf plant (Calophyllum Inophyllum) is being considered as a potential 2nd generation biodiesel source due to high seed oil content, high fruit production rate, simple cultivation and ability to grow in a wide range of climate conditions. However, however, due to the high free fatty acid (FFA) content in this oil, the potential of this biodiesel feedstock is still unrealized, and little research has been undertaken on it. In this study, transesterification of beauty leaf oil to produce biodiesel has been investigated. A two-step biodiesel conversion method consisting of acid catalysed pre-esterification and alkali catalysed transesterification has been utilized. The three main factors that drive the biodiesel (fatty acid methyl ester (FAME)) conversion from vegetable oil (triglycerides) were studied using response surface methodology (RSM) based on a Box-Behnken experimental design. The factors considered in this study were catalyst concentration, methanol to oil molar ratio and reaction temperature. Linear and full quadratic regression models were developed to predict FFA and FAME concentration and to optimize the reaction conditions. The significance of these factors and their interaction in both stages was determined using analysis of variance (ANOVA). The reaction conditions for the largest reduction in FFA concentration for acid catalysed pre-esterification was 30:1 methanol to oil molar ratio, 10% (w/w) sulfuric acid catalyst loading and 75 °C reaction temperature. In the alkali catalysed transesterification process 7.5:1 methanol to oil molar ratio, 1% (w/w) sodium methoxide catalyst loading and 55 °C reaction temperature were found to result in the highest FAME conversion. The good agreement between model outputs and experimental results demonstrated that this methodology may be useful for industrial process optimization for biodiesel production from beauty leaf oil and possibly other industrial processes as well.

Aitosuklaa jäätelöpuikon kuorrutteena

Tutkimuksen kirjallisuuskatsauksessa keskityttiin jäätelöpuikkoihin, erilaisiin suklaakuorrutteisiin ja elintarvikkeiden kuorruttamiseen suklaalla. Lisäksi kirjallisuuskatsauksessa perehdyttiin suklaan koostumukseen, nestemäisen suklaan virtausominaisuuksiin ja koostumuksen ja virtausominaisuuksien välisiin vuorovaikutuksiin. Kokeellisessa osassa tavoitteena oli selvittää, miten maitosuklaakuorrutteen rasvapitoisuuden, emulgointiainepitoisuuden ja kuorrutteen lämpötilanvaihtelut vaikuttavat kuorrutteen viskositeettiin, myötöjännitykseen, jähmettymisaikaan ja jäätelöpuikon päälle jäävän kuorrutteen määrään. Erityisesti pyrittiin selvittämään, miten jäätelöpuikon päälle jäävän kuorrutteen määrää saadaan säädeltyä kuorrutteen rasvapitoisuutta, emulgointiainepitoisuutta ja lämpötilaa muuttamalla. Tutkimuksen koeasetelma tehtiin Box-Behnken-mallilla. Selittäviksi muuttujiksi tutkimukseen valittiin kuorrutteen rasvan määrä, emulgointiaineen määrä ja kuorrutteen lämpötila jäätelöpuikkoja kuorrutettaessa. Vastemuuttujina oli kuorrutteen jähmettymisaika, viskositeetti, myötöjännitys ja jäätelöpuikon päälle jäävän kuorrutteen määrä. Tulokset käsiteltiin regressioanalyysin avulla. Muuttujien välisiä vuorovaikutuksia tutkittiin vastepintamallilla. Vastemuuttujien välisiä korrelaatioita tutkittaessa käytettiin Pearsonin korrelaatiokerrointa. Kuorrutteen rasvan määrän lisääntyminen vähensi tilastollisesti merkitsevästi jäätelöpuikon päälle jäävän kuorrutteen määrää, kuorrutteen jähmettymisaikaa, viskositeettia ja myötöjännitystä. Emulgointiaineen määrän lisääminen kuorrutteessa pienensi kuorrutteen määrää jäätelöpuikon päällä, kuorrutteen jähmettymisaikaa ja kuorrutteen myötöjännitystä. Kuorrutteen lämpötilan lisääminen jäätelöpuikkoja kuorrutettaessa pienensi kuorrutteen määrää ja viskositeettia. Kuorrutteen jähmettymisaika sen sijaan piteni lämpötilaa lisättäessä. Tutkimuksen perusteella voidaan sanoa, että jäätelöpuikkoja kastettaessa suklaakuorrutteen lämpötila, rasvan määrä ja lesitiinin määrä vaikuttivat jäätelöpuikon päälle jäävän kuorrutteen määrään. Vastepintamallinnuksen käyttö soveltui hyvin suklaakuorrutteen määrän tutkimiseen. Sen avulla saatiin selvitettyä, miten jäätelöpuikon päälle jäävän kuorrutteen määrää saadaan säädeltyä muuttamalla kuorrutteen emulgointiainepitoisuutta, rasvapitoisuutta ja lämpötilaa.

Hexavalent Chromium Adsorption by a Novel Activated Carbon Prepared by Microwave Activation

Microwave heating reduces the preparation time and improves the adsorption quality of activated carbon. In this study, activated carbon was prepared by impregnation of palm kernel fiber with phosphoric acid followed by microwave activation. Three different types of activated carbon were prepared, having high surface areas of 872 m2 g-1, 1256 m2 g-1, and 952 m2 g-1 and pore volumes of 0.598 cc g-1, 1.010 cc g-1, and 0.778 cc g-1, respectively. The combined effects of the different process parameters, such as the initial adsorbate concentration, pH, and temperature, on adsorption efficiency were explored with the help of Box-Behnken design for response surface methodology (RSM). The adsorption rate could be expressed by a polynomial equation as the function of the independent variables. The hexavalent chromium adsorption rate was found to be 19.1 mg g-1 at the optimized conditions of the process parameters, i.e., initial concentration of 60 mg L-1, pH of 3, and operating temperature of 50 oC. Adsorption of Cr(VI) by the prepared activated carbon was spontaneous and followed second-order kinetics. The adsorption mechanism can be described by the Freundlich Isotherm model. The prepared activated carbon has demonstrated comparable performance to other available activated carbons for the adsorption of Cr(VI).

Improving the microbial production of biofuels through metabolic engineering

Les défis conjoints du changement climatique d'origine anthropique et la diminution des réserves de combustibles fossiles sont le moteur de recherche intense pour des sources d'énergie alternatives. Une avenue attrayante est d'utiliser un processus biologique pour produire un biocarburant. Parmi les différentes options en matière de biocarburants, le bio-hydrogène gazeux est un futur vecteur énergétique attrayant en raison de son efficacité potentiellement plus élevé de conversion de puissance utilisable, il est faible en génération inexistante de polluants et de haute densité d'énergie. Cependant, les faibles rendements et taux de production ont été les principaux obstacles à l'application pratique des technologies de bio-hydrogène. Des recherches intensives sur bio-hydrogène sont en cours, et dans les dernières années, plusieurs nouvelles approches ont été proposées et étudiées pour dépasser ces inconvénients. À cette fin, l'objectif principal de cette thèse était d'améliorer le rendement en hydrogène moléculaire avec un accent particulier sur l'ingénierie métabolique et l’utilisation de bioprocédés à variables indépendantes. Une de nos hypothèses était que la production d’hydrogène pourrait être améliorée et rendue plus économiquement viable par ingénierie métabolique de souches d’Escherichia coli producteurs d’hydrogène en utilisant le glucose ainsi que diverses autres sources de carbone, y compris les pentoses. Les effets du pH, de la température et de sources de carbone ont été étudiés. La production maximale d'hydrogène a été obtenue à partir de glucose, à un pH initial de 6.5 et une température de 35°C. Les études de cinétiques de croissance ont montré que la μmax était 0.0495 h-1 avec un Ks de 0.0274 g L-1 lorsque le glucose est la seule source de carbone en milieu minimal M9. .Parmi les nombreux sucres et les dérivés de sucres testés, les rendements les plus élevés d'hydrogène sont avec du fructose, sorbitol et D-glucose; 1.27, 1.46 et 1.51 mol H2 mol-1 de substrat, respectivement. En outre, pour obtenir les interactions entre les variables importantes et pour atteindre une production maximale d'hydrogène, un design 3K factoriel complet Box-Behnken et la méthodologie de réponse de surface (RSM) ont été employées pour la conception expérimentale et l'analyse de la souche d'Escherichia coli DJT135. Le rendement en hydrogène molaire maximale de 1.69 mol H2 mol-1 de glucose a été obtenu dans les conditions optimales de 75 mM de glucose, à 35°C et un pH de 6.5. Ainsi, la RSM avec un design Box-Behken était un outil statistique utile pour atteindre des rendements plus élevés d'hydrogène molaires par des organismes modifiés génétiquement. Ensuite, l'expression hétérologue de l’hydrogénases soluble [Ni-Fe] de Ralstonia eutropha H16 (l'hydrogénase SH) a tenté de démontrer que la mise en place d'une voie capable de dériver l'hydrogène à partir de NADH pourrait surpasser le rendement stoechiométrique en hydrogène.. L’expression a été démontrée par des tests in vitro de l'activité enzymatique. Par ailleurs, l'expression de SH a restaurée la croissance en anaérobie de souches mutantes pour adhE, normalement inhibées en raison de l'incapacité de réoxyder le NADH. La mesure de la production d'hydrogène in vivo a montré que plusieurs souches modifiées métaboliquement sont capables d'utiliser l'hydrogénase SH pour dériver deux moles d’hydrogène par mole de glucose consommé, proche du maximum théorique. Une autre stratégie a montré que le glycérol brut pourrait être converti en hydrogène par photofermentation utilisant Rhodopseudomonas palustris par photofermentation. Les effets de la source d'azote et de différentes concentrations de glycérol brut sur ce processus ont été évalués. À 20 mM de glycérol, 4 mM glutamate, 6.1 mol hydrogène / mole de glycérol brut ont été obtenus dans des conditions optimales, un rendement de 87% de la théorie, et significativement plus élevés que ce qui a été réalisé auparavant. En prolongement de cette étude, l'optimisation des paramètres a également été utilisée. Dans des conditions optimales, une intensité lumineuse de 175 W/m2, 30 mM glycérol et 4.5 mM de glutamate, 6.69 mol hydrogène / mole de glycérol brut ont été obtenus, soit un rendement de 96% de la valeur théorique. La détermination de l'activité de la nitrogénase et ses niveaux d'expression ont montré qu'il y avait relativement peu de variation de la quantité de nitrogénase avec le changement des variables alors que l'activité de la nitrogénase variait considérablement, avec une activité maximale (228 nmol de C2H4/ml/min) au point central optimal. Dans la dernière section, la production d'hydrogène à partir du glucose via la photofermentation en une seule étape a été examinée avec la bactérie photosynthétique Rhodobacter capsulatus JP91 (hup-). La méthodologie de surface de réponse avec Box-Behnken a été utilisée pour optimiser les variables expérimentales de façon indépendante, soit la concentration de glucose, la concentration du glutamate et l'intensité lumineuse, ainsi que d'examiner leurs effets interactifs pour la maximisation du rendement en hydrogène moléculaire. Dans des conditions optimales, avec une intensité lumineuse de 175 W/m2, 35 mM de glucose, et 4.5 mM de glutamate,, un rendement maximal d'hydrogène de 5.5 (± 0.15) mol hydrogène /mol glucose, et un maximum d'activité de la nitrogénase de 246 (± 3.5) nmol C2H4/ml/min ont été obtenus. L'analyse densitométrique de l'expression de la protéine-Fe nitrogenase dans les différentes conditions a montré une variation significative de l'expression protéique avec un maximum au point central optimisé. Même dans des conditions optimales pour la production d'hydrogène, une fraction significative de la protéine Fe a été trouvée dans l'état ADP-ribosylée, suggérant que d'autres améliorations des rendements pourraient être possibles. À cette fin, un mutant amtB dérivé de Rhodobacter capsulatus JP91 (hup-) a été créé en utilisant le vecteur de suicide pSUP202. Les résultats expérimentaux préliminaires montrent que la souche nouvellement conçue métaboliquement, R. capsulatus DG9, produit 8.2 (± 0.06) mol hydrogène / mole de glucose dans des conditions optimales de cultures discontinues (intensité lumineuse, 175 W/m2, 35 mM de glucose et 4.5 mM glutamate). Le statut d'ADP-ribosylation de la nitrogénase-protéine Fe a été obtenu par Western Blot pour la souche R. capsulatus DG9. En bref, la production d'hydrogène est limitée par une barrière métabolique. La principale barrière métabolique est due au manque d'outils moléculaires possibles pour atteindre ou dépasser le rendement stochiométrique en bio-hydrogène depuis les dernières décennies en utilisant les microbes. À cette fin, une nouvelle approche d’ingénierie métabolique semble très prometteuse pour surmonter cette contrainte vers l'industrialisation et s'assurer de la faisabilité de la technologie de la production d'hydrogène. Dans la présente étude, il a été démontré que l’ingénierie métabolique de bactéries anaérobiques facultatives (Escherichia coli) et de bactéries anaérobiques photosynthétiques (Rhodobacter capsulatus et Rhodopseudomonas palustris) peuvent produire de l'hydrogène en tant que produit majeur à travers le mode de fermentation par redirection métabolique vers la production d'énergie potentielle. D'autre part, la méthodologie de surface de réponse utilisée dans cette étude représente un outil potentiel pour optimiser la production d'hydrogène en générant des informations appropriées concernant la corrélation entre les variables et des producteurs de bio-de hydrogène modifiés par ingénierie métabolique. Ainsi, un outil d'optimisation des paramètres représente une nouvelle avenue pour faire un pont entre le laboratoire et la production d'hydrogène à l'échelle industrielle en fournissant un modèle mathématique potentiel pour intensifier la production de bio-hydrogène. Par conséquent, il a été clairement mis en évidence dans ce projet que l'effort combiné de l'ingénierie métabolique et la méthodologie de surface de réponse peut rendre la technologie de production de bio-hydrogène potentiellement possible vers sa commercialisation dans un avenir rapproché.

Optimization of Lignin Peroxidase, Manganese Peroxidase, and Lac Production from Ganoderma lucidum Under Solid State Fermentation of Pineapple Leaf

This study was undertaken to isolate ligninase-producing white-rot fungi for use in the extraction of fibre from pineapple leaf agriwaste. Fifteen fungal strains were isolated from dead tree trunks and leaf litter. Ligninolytic enzymes (lignin peroxidase (LiP), manganese peroxidase (MnP), and laccase (Lac)), were produced by solid-state fermentation (SSF) using pineapple leaves as the substrate. Of the isolated strains, the one showing maximum production of ligninolytic enzymes was identified to be Ganoderma lucidum by 18S ribotyping. Single parameter optimization and response surface methodology of different process variables were carried out for enzyme production. Incubation period, agitation, and Tween-80 were identified to be the most significant variables through Plackett-Burman design. These variables were further optimized by Box-Behnken design. The overall maximum yield of ligninolytic enzymes was achieved by experimental analysis under these optimal conditions. Quantitative lignin analysis of pineapple leaves by Klason lignin method showed significant degradation of lignin by Ganoderma lucidum under SSF

Avaliação de metodologia de preparo de amostra de petróleo por digestão ácida auxiliada por microondas para determinação de metais por ICP-OES

This project describes a methodology optimization that would allow for a more efficient microwave assisted digestion process for petroleum samples. With the possible chance to vary various factors at once to see if any one factor was significant enough in the answers, experimental planning was used. Microwave assisted digestion allows, through the application of potency, an increasing number of collisions between the HNO3 and H2O2 molecules, favoring sample opening for complex matrixes. For this, a 24 factorial experimental planning was used, varying potency, time and the volumes for HNO3 65% and H2O2 30%. To achieve the desired answers, several elements were monitored (C, Cu, Cr, Fe, Ni, Zn and V) through Inductively coupled plasma atomic emission spectroscopy (ICP-OES). With this initial study it was noticed that the HNO3 was not a significant factor for any of the statistical studies for any of the analytes and the other 3 factors and their interactions showed statistical significance. A Box Behnken experimental planning was used taking in consideration 3 factors: H2O2 volume, time (min) and Potency (W), Nitric Acid kept at 4mL for a mass of 0,1g of petroleum. The results were extremely satisfying showing higher efficiency in the digestion process and taking in a responsibility between the answers for each analyte and the carbon monitoring was achieved in the following conditions: 7mL of H2O2, 700 Watts of potency and a reaction time of 7 minutes with 4mL de HNO3 for a mass of 0,1g of petroleum. The optimized digestion process was applied to four different petroleum samples and the analytes determined by ICP-OES

Estudo dos parâmetros de extração de fenol de efluentes aquosos por um tensoativo não iônico

Environmental sustainability has become one of the topics of greatest interest in industry, mainly due to effluent generation. Phenols are found in many industries effluents, these industries might be refineries, coal processing, pharmaceutical, plastics, paints and paper and pulp industries. Because phenolic compounds are toxic to humans and aquatic organisms, Federal Resolution CONAMA No. 430 of 13.05.2011 limits the maximum content of phenols, in 0.5 mg.L-1, for release in freshwater bodies. In the effluents treatment, the liquid-liquid extraction process is the most economical for the phenol recovery, because consumes little energy, but in most cases implements an organic solvent, and the use of it can cause some environmental problems due to the high toxicity of this compound. Because of this, exists a need for new methodologies, which aims to replace these solvents for biodegradable ones. Some literature studies demonstrate the feasibility of phenolic compounds removing from aqueous effluents, by biodegradable solvents. In this extraction kind called "Cloud Point Extraction" is used a nonionic surfactant as extracting agent of phenolic compounds. In order to optimize the phenol extraction process, this paper studies the mathematical modeling and optimization of extraction parameters and investigates the effect of the independent variables in the process. A 32 full factorial design has been done with operating temperature and surfactant concentration as independent variables and, parameters extraction: Volumetric fraction of coacervate phase, surfactant and residual concentration of phenol in dilute phase after separation phase and phenol extraction efficiency, as dependent variables. To achieve the objectives presented before, the work was carried out in five steps: (i) selection of some literature data, (ii) use of Box-Behnken model to find out mathematical models that describes the process of phenol extraction, (iii) Data analysis were performed using STATISTICA 7.0 and the analysis of variance was used to assess the model significance and prediction (iv) models optimization using the response surface method (v) Mathematical models validation using additional measures, from samples different from the ones used to construct the model. The results showed that the mathematical models found are able to calculate the effect of the surfactant concentration and the operating temperature in each extraction parameter studied, respecting the boundaries used. The models optimization allowed the achievement of consistent and applicable results in a simple and quick way leading to high efficiency in process operation.

A Semi-Continuous Analyzer for the Fluorimetric Determination of Atmospheric Formaldehyde

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação do processo de produção de etanol pela fermentação do caldo de mandiocaba (Manihot esculenta Crantz)

Foram realizadas determinações físico-químicas na raiz de mandiocaba, sendo estas: umidade, fibras, proteínas, cinzas, lipídios totais, açúcares redutores e totais; o caldo foi caracterizado através das análises de pH, sólidos solúveis totais, glicose e acidez titulável. Após o conhecimento dos constituintes físico-químicos da matéria-prima, o caldo de mandioca doce foi extraído e fermentado utilizando a levedura Saccharomycescerevisiae PE-2. Foram realizados 15 ensaios que seguiam as condições determinadas através do planejamento experimental de Box-Behnken, com 3 variáveis independentes: temperatura (ºC) (X1), pH (X2), e concentração de inóculo (g/L) (X3); os limites dos níveis de trabalho foram determinados através de dados encontrados na literatura; a análise estatística foi realizada com p>0,05. Através da análise de variância foi proposto um modelo polinomial de segunda ordem para a resposta teor alcoólico (ºGl), e com a utilização da metodologia de superfície de resposta à condição ótima para o desenvolvimento do processo fermentativo do caldo de mandioca doce sem adição de nutrientes e em sua concentração de substrato original (6,46 g/L), a: temperatura de 28ºC, pH de 4,88, e concentração de inóculo de 10 g/L. Nestas condições foi realizado um ensaio, cujo objetivo foi o de levantar as curvas de crescimento celular (levedura), produção de CO₂, consumo de açúcares redutores e produção de etanol, para melhor compreensão do processo de fermentação do caldo de mandioca doce. Através da curva de crescimento celular foi determinada a duração da fase exponencial, utilizando o método de regressão linear; neste estudo esta etapa ocorreu em diferentes intervalos de tempo. O valor de µm encontrado foi de 0,05 h^-1.