Effect Of Platform Connection And Abutment Material On Stress Distribution In Single Anterior Implant-supported Restorations: A Nonlinear 3-dimensional Finite Element Analysis.

Although various abutment connections and materials have recently been introduced, insufficient data exist regarding the effect of stress distribution on their mechanical performance. The purpose of this study was to investigate the effect of different abutment materials and platform connections on stress distribution in single anterior implant-supported restorations with the finite element method. Nine experimental groups were modeled from the combination of 3 platform connections (external hexagon, internal hexagon, and Morse tapered) and 3 abutment materials (titanium, zirconia, and hybrid) as follows: external hexagon-titanium, external hexagon-zirconia, external hexagon-hybrid, internal hexagon-titanium, internal hexagon-zirconia, internal hexagon-hybrid, Morse tapered-titanium, Morse tapered-zirconia, and Morse tapered-hybrid. Finite element models consisted of a 4×13-mm implant, anatomic abutment, and lithium disilicate central incisor crown cemented over the abutment. The 49 N occlusal loading was applied in 6 steps to simulate the incisal guidance. Equivalent von Mises stress (σvM) was used for both the qualitative and quantitative evaluation of the implant and abutment in all the groups and the maximum (σmax) and minimum (σmin) principal stresses for the numerical comparison of the zirconia parts. The highest abutment σvM occurred in the Morse-tapered groups and the lowest in the external hexagon-hybrid, internal hexagon-titanium, and internal hexagon-hybrid groups. The σmax and σmin values were lower in the hybrid groups than in the zirconia groups. The stress distribution concentrated in the abutment-implant interface in all the groups, regardless of the platform connection or abutment material. The platform connection influenced the stress on abutments more than the abutment material. The stress values for implants were similar among different platform connections, but greater stress concentrations were observed in internal connections.

Direct Adhesive Pin-retained Restorations For Severely Worn Dentition Treatment: A 1.5-year Follow-up Report.

Excessive occlusal surface wear can result in occlusal disharmony, functional and esthetic impairment. As a therapeutic approach, conventional single crowns have been proposed, but this kind of treatment is complex, highly invasive and expensive. This case report describes the clinical outcomes of an alternative minimally invasive treatment based on direct adhesive-pin retained restorations. A 64-year-old woman with severely worn dentition, eating problems related to missing teeth and generalized tooth hypersensitivity was referred for treatment. Proper treatment planning based on the diagnostic wax-up simulation was used to guide the reconstruction of maxillary anterior teeth with direct composite resin over self-threading dentin pins. As the mandibular remaining teeth were extremely worn, a tooth-supported overdenture was installed. A stabilization splint was also used to protect the restorations. This treatment was a less expensive alternative to full-mouth rehabilitation with positive esthetic and functional outcomes after 1.5 years of follow-up.

Effect Of Daily Use Of An Enzymatic Denture Cleanser On Candida Albicans Biofilms Formed On Polyamide And Poly(methyl Methacrylate) Resins: An In Vitro Study.

Candida biofilms on denture surfaces are substantially reduced after a single immersion in denture cleanser. However, whether this effect is maintained when dentures are immersed in cleanser daily is unclear. The purpose of this study was to evaluate the effect of the daily use of enzymatic cleanser on Candida albicans biofilms on denture base materials. The surfaces of polyamide and poly(methyl methacrylate) resin specimens (n=54) were standardized and divided into 12 groups (n=9 per group), according to study factors (material type, treatment type, and periods of treatment). Candida albicans biofilms were allowed to form over 72 hours, after which the specimens were treated with enzymatic cleanser once daily for 1, 4, or 7 days. Thereafter, residual biofilm was ultrasonically removed and analyzed for viable cells (colony forming units/mm(2)) and enzymatic activity (phospholipase, aspartyl-protease, and hemolysin). Factors that interfered with the response variables were analyzed by 3-way ANOVA with the Holm-Sidak multiple comparison method (α=.05). Polyamide resin presented more viable cells of Candida albicans (P<.001) for both the evaluated treatment types and periods. Although enzymatic cleansing significantly (P<.001) reduced viable cells, daily use did not maintain this reduction (P<.001). Phospholipase activity significantly increased with time (P<.001) for both materials and treatments. However, poly(methyl methacrylate) based resin (P<.001) and enzymatic cleansing treatment (P<.001) contributed to lower phospholipase activity. Aspartyl-protease and hemolysin activities were not influenced by study factors (P>.05). Although daily use of an enzymatic cleanser reduced the number of viable cells and phospholipase activity, this treatment was not effective against residual biofilm over time.

The Effect Of Poly(methyl Methacrylate) Surface Treatments On The Adhesion Of Silicone-based Resilient Denture Liners.

Different surface treatment protocols of poly(methyl methacrylate) have been proposed to improve the adhesion of silicone-based resilient denture liners to poly(methyl methacrylate) surfaces. The purpose of this study was to evaluate the effect of different poly(methyl methacrylate) surface treatments on the adhesion of silicone-based resilient denture liners. Poly(methyl methacrylate) specimens were prepared and divided into 4 treatment groups: no treatment (control), methyl methacrylate for 180 seconds, acetone for 30 seconds, and ethyl acetate for 60 seconds. Poly(methyl methacrylate) disks (30.0 × 5.0 mm; n = 10) were evaluated regarding surface roughness and surface free energy. To evaluate tensile bond strength, the resilient material was applied between 2 treated poly(methyl methacrylate) bars (60.0 × 5.0 × 5.0 mm; n = 20 for each group) to form a 2-mm-thick layer. Data were analyzed by 1-way ANOVA and the Tukey honestly significant difference tests (α = .05). A Pearson correlation test verified the influence of surface properties on tensile bond strength. Failure type was assessed, and the poly(methyl methacrylate) surface treatment modifications were visualized with scanning electron microscopy. The surface roughness was increased (P < .05) by methyl methacrylate treatment. For the acetone and ethyl acetate groups, the surface free energy decreased (P < .05). The tensile bond strength was higher for the methyl methacrylate and ethyl acetate groups (P < .05). No correlation was found regarding surface properties and tensile bond strength. Specimens treated with acetone and methyl methacrylate presented a cleaner surface, whereas the ethyl acetate treatment produced a porous topography. The methyl methacrylate and ethyl acetate surface treatment protocols improved the adhesion of a silicone-based resilient denture liner to poly(methyl methacrylate).

Recolonization Of Mutans Streptococci After Application Of Chlorhexidine Gel.

Streptococcus mutans is specifically suppressed by intensive treatment with chlorhexidine gel, but the time for recolonization and the effect on other oral bacteria are not totally clear. In this study, recolonization of mutans streptococci was evaluated in nine healthy adult volunteers, who were highly colonized with this microorganism. Stimulated saliva was collected before (baseline) and at 1, 7, 14, 21 and 28 days after application of 1% chlorhexidine gel on volunteers' teeth for two consecutive days. On each day, the gel was applied using disposable trays for 3 x 5 min with intervals of 5 min between each application. Saliva was plated on blood agar to determine total microorganisms (TM); on mitis salivarius agar to determine total streptococci (TS) and on mitis salivarius agar plus bacitracin to determine mutans streptococci (MS). Chlorhexidine was capable of reducing the counts of MS and the proportion of MS with regard to total microorganisms (%MS/TM) (p<0.05), but these values did not differ statistically from baseline (p>0.05) after 14 days for MS and 21 days for %MS/TM. The counts of TM and TS and the proportion of MS to total streptococci did not differ statistically from baseline (p>0.05) after chlorhexidine treatment. The results suggest that the effect of chlorhexidine gel treatment on suppression of mutans streptococci is limited to less than a month in highly colonized individuals.

Biofilm And Saliva Affect The Biomechanical Behavior Of Dental Implants.

Friction coefficient (FC) was quantified between titanium-titanium (Ti-Ti) and titanium-zirconia (Ti-Zr), materials commonly used as abutment and implants, in the presence of a multispecies biofilm (Bf) or salivary pellicle (Pel). Furthermore, FC was used as a parameter to evaluate the biomechanical behavior of a single implant-supported restoration. Interface between Ti-Ti and Ti-Zr without Pel or Bf was used as control (Ctrl). FC was recorded using tribometer and analyzed by two-way Anova and Tukey test (p<0.05). Data were transposed to a finite element model of a dental implant-supported restoration. Models were obtained varying abutment material (Ti and Zr) and FCs recorded (Bf, Pel, and Ctrl). Maximum and shear stress were calculated for bone and equivalent von Misses for prosthetic components. Data were analyzed using two-way ANOVA (p<0.05) and percentage of contribution for each condition (material and FC) was calculated. FC significant differences were observed between Ti-Ti and Ti-Zr for Ctrl and Bf groups, with lower values for Ti-Zr (p<0.05). Within each material group, Ti-Ti differed between all treatments (p<0.05) and for Ti-Zr, only Pel showed higher values compared with Ctrl and Bf (p<0.05). FC contributed to 89.83% (p<0.05) of the stress in the screw, decreasing the stress when the FC was lower. FC resulted in an increase of 59.78% of maximum stress in cortical bone (p=0.05). It can be concluded that the shift of the FC due to the presence of Pel or Bf is able to jeopardize the biomechanical behavior of a single implant-supported restoration.

Alteração dimensional linear de resinas para bases de próteses polimerizadas com microondas

This study examined the influence of three polymerization cycles (1: heat cure - long cycle; 2: heat cure - short cycle; and 3: microwave activation) on the linear dimensions of three denture base resins, immediately after deflasking, and 30 days after storage in distilled water at 37± 2ºC. The acrylic resins used were: Clássico, Lucitone 550 and Acron MC. The first two resins were submitted to all three polymerization cycles, and the Acron MC resin was cured by microwave activation only. The samples had three marks, and dimensions of 65 mm in length, 10 mm in width and 3 mm in thickness. Twenty-one test specimens were fabricated for each combination of resin and cure cycle, and they were submitted to three linear dimensional evaluations for two positions (A and B). The changes were evaluated using a microscope. The results indicated that all acrylic resins, regardless of the cure cycle, showed increased linear dimension after 30 days of storage in water. The composition of the acrylic resin affected the results more than the cure cycles, and the conventional acrylic resin (Lucitone 550 and Clássico) cured by microwave activation presented similar results when compared with the resin specific for microwave activation.

Relationship among malocclusion, number of occlusal pairs and mastication

This study evaluated the relationship among malocclusion, number of occlusal pairs, masticatory performance, masticatory time and masticatory ability in completely dentate subjects. Eighty healthy subjects (mean age = 19.40 ± 4.14 years) were grouped according to malocclusion diagnosis (n = 16): Class I, Class Class II-2, Class III and Normocclusion (control). Number of occlusal pairs was determined clinically. Masticatory performance was evaluated by the sieving method, and the time used for the comminute test food was registered as the masticatory time. Masticatory ability was measured by a dichotomic self-perception questionnaire. Statistical analysis was done by one-way ANOVA, ANOVA on ranks, Chi-Square and Spearman tests. Class II-1 and III malocclusion groups presented a smaller number of occlusal pairs than Normocclusion (p < 0.0001), Class I (p < 0.001) and II-2 (p < 0.0001) malocclusion groups. Class I, and III malocclusion groups showed lower masticatory performance values compared to Normocclusion (p < 0.05) and Class II-2 (p < 0.05) malocclusion groups. There were no differences in masticatory time (p = 0.156) and ability (χ2 = 3.58/p= 0.465) among groups. Occlusal pairs were associated with malocclusion (rho = 0.444/p < 0.0001) and masticatory performance (rho = 0.393/p < 0.0001), but malocclusion was not correlated with masticatory performance (rho = 0.116/p= 0.306). In conclusion, masticatory performance and ability were not related to malocclusion, and subjects with Class I, II-1 and III malocclusions presented lower masticatory performance because of their smaller number of occlusal pairs.

Estudo de família brasileira portadora de deficiência auditiva sensorioneural não-sindrômica com herança mitocondrial

O presente estudo teve como objetivo descrever os achados audiológicos e genéticos de nove membros de uma família brasileira que apresenta a mutação no DNA mitocondrial. Todos os nove membros realizaram estudo genético, avaliação foniátrica e audiológica (audiometria tonal e logoaudiometria). O estudo genético revelou a presença de mutação mitocondrial A1555G no gene 12S rRNA (MT-RNR-1) do DNA mitocondrial em todos os sujeitos. Oito sujeitos apresentaram deficiência auditiva e somente um apresentou limiares auditivos normais até o término da realização do estudo. Os resultados audiológicos apontaram para perdas auditivas bilaterais, com prevalência das simétricas, de configurações e graus variados (de moderado a profundo) e pós-linguais. Progressão da perda auditiva foi observada em dois irmãos afetados. Não foi possível afirmar a época do início da perda auditiva por falta de informação dos sujeitos, no entanto, observou-se manifestação da perda em crianças e adultos. As mutações no DNA mitocondrial representam uma causa importante de perda auditiva, sendo imprescindível a realização do diagnóstico etiopatológico, a fim de retardar o início ou evitar a progressão da surdez.

Estudo de família brasileira portadora de deficiência auditiva sensorioneural não-sindrômica com herança mitocondrial

O presente estudo teve como objetivo descrever os achados audiológicos e genéticos de nove membros de uma família brasileira que apresenta a mutação no DNA mitocondrial. Todos os nove membros realizaram estudo genético, avaliação foniátrica e audiológica (audiometria tonal e logoaudiometria). O estudo genético revelou a presença de mutação mitocondrial A1555G no gene 12S rRNA (MT-RNR-1) do DNA mitocondrial em todos os sujeitos. Oito sujeitos apresentaram deficiência auditiva e somente um apresentou limiares auditivos normais até o término da realização do estudo. Os resultados audiológicos apontaram para perdas auditivas bilaterais, com prevalência das simétricas, de configurações e graus variados (de moderado a profundo) e pós-linguais. Progressão da perda auditiva foi observada em dois irmãos afetados. Não foi possível afirmar a época do início da perda auditiva por falta de informação dos sujeitos, no entanto, observou-se manifestação da perda em crianças e adultos. As mutações no DNA mitocondrial representam uma causa importante de perda auditiva, sendo imprescindível a realização do diagnóstico etiopatológico, a fim de retardar o início ou evitar a progressão da surdez.

Classificação de microáreas de risco com uso de mineraçãode dados

OBJETIVO: Identificar, com o auxílio de técnicas computacionais, regras referentes às condições do ambiente físico para a classificação de microáreas de risco. MÉTODOS: Pesquisa exploratória, desenvolvida na cidade de Curitiba, PR, em 2007, dividida em três etapas: identificação de atributos para classificar uma microárea; construção de uma base de dados; e aplicação do processo de descoberta de conhecimento em base de dados, por meio da aplicação de mineração de dados. O conjunto de atributos envolveu as condições de infra- estrutura, hidrografia, solo, área de lazer, características da comunidade e existência de vetores. A base de dados foi construída com dados obtidos em entrevistas com agentes comunitários de saúde, sendo utilizado um questionário com questões fechadas, elaborado com os atributos essenciais, selecionados por especialistas. RESULTADOS: Foram identificados 49 atributos, sendo 41 essenciais e oito irrelevantes. Foram obtidas 68 regras com a mineração de dados, as quais foram analisadas sob a perspectiva de desempenho e qualidade e divididas em dois conjuntos: as inconsistentes e as que confirmam o conhecimento de especialistas. A comparação entre os conjuntos mostrou que as regras que confirmavam o conhecimento, apesar de terem desempenho computacional inferior, foram consideradas mais interessantes. CONCLUSÕES: A mineração de dados ofereceu um conjunto de regras úteis e compreensíveis, capazes de caracterizar microáreas, classificando-as quanto ao grau do risco, com base em características do ambiente físico. A utilização das regras propostas permite que a classificação de uma microárea possa ser realizada de forma mais rápida, menos subjetiva, mantendo um padrão entre as equipes de saúde, superando a influência da percepção particular de cada componente da equipe.

Levantamento planorbídico do Estado de São Paulo: 8ª Região Administrativa (grande área de São José do Rio Preto)

Para reconhecer a distribuição dos planorbídeos na 8ª Região Administrativa do Estado de São Paulo, 286 lotes de caramujos procedentes dos 85 municípios que a constituem foram examinados e identificados no Laboratório de Malacologia da SUCEN. Biomphalaria straminea, que ocorre em quatro criadouros - um em Altair e três em S. José do Rio Preto, foi a única espécie identificada capaz de vir a comportar-se naturalmente como hospedeira intermediária de S.mansoni. Isto demonstra que são mínimas as probabilidades da esquistossomose vir a instalar-se na área estudada.

Caracterização de bactérias dos gêneros Mima e Herella (Tribo Mimeae, DeBord, 1942): 1) Propriedade morfo-bioquímicas e sensibilidade aos antibióticos

No presente trabalho, os autores estudaram as propriedades morfo-bioquímicas e a sinsibilidade aos antibióticos de 19 amostras de bactérias dos gêneros Mima e Herellea isoladas de material clínico e identificadas como Mima polymorpha variedade oxidans, Mima polymorpha e Herellea vaginicola. No estudo bioquímico observou-se que Herellea vaginicola foi oxidase negativa e em meio complexo nitrogenado, consistentemente ataca a glicose, galactose, manose, arabinose, xilose, lactose a 10% e irregularmente ataca a ramnose e a celobiose; em base sintética nitrogenada, além das atividades citadas, consistentemente produziu ácido a partir da lactose. Mima polymopha foi oxidase negativa, não apresentando atividade glicidolítica, quer em meio complexo nitrogenado, quer em base sintética nitrogenada. Mima polymorpha var. oxidans, foi oxidase positiva, não revelando nenhuma atividade glicidolítica. Herellea vaginicola e Mima polymorpha mostraram grande sensibilidade à gabromicina, knamicina, neomicina, colistin, sendo que a última também foi muito sensível ao cloranfenicol e rovamicina. Mima polymorpha var. oxidans, apresentou grande sensibilidade à knamicina, neomicina, colistin, cloranfenicol e wintomylon. A sensibilidade das amostras a 1 a 0,1 unidade de penicilina/ml, nas condições ensaiadas no presente trabalho, não foi absoluta, como a observada por Baumann, Doudoroff & Stanier (1968a) que permitisse uma separação entre amostras oxidase positiva e negativa ou uma diferenciação dentro do grupo das bactérias oxidase positiva.

Isolamento e caracterização de Pseudomonas maltophilia (Hugh & Ryschenkow, 1960) de material clínico humano, na cidade do Rio de Janeiro

Os autores estudaram as propriedades morfo-bioquímicas e a sensibilidade às substâncias antimicrobianas, de uma nova e rara espécie de Pseudomonas, a Pseudomonas maltophilia (Hugh & Ryschenkow, 1960), isolada de secração vaginal. Como características marcantes, dentre mais de 65 testadas, as amostras estudadas mostraram ser: oxidase negativa e lisina descarboxilase positiva; produziram desoxiribonuclease e um pigmento escuro que se difunde no meio; atacaram oxidativamente a maltose tanto em meio complexo nitrogenado como em meio de Hugh & Leifson e hidrolisaram a esculina. As amostras foram sensíveis ao cloranfenicol, gentamicina, kanamicina, colistin e gabromicina.