Variable 360° Vector-Sum Phase Shifter With Coarse and Fine Vector Scaling

A CMOS vector-sum phase shifter covering the full 360° range is presented in this paper. Broadband operational transconductance amplifiers with variable transconductance provide coarse scaling of the quadrature vector amplitudes. Fine scaling of the amplitudes is accomplished using a passive resistive network. Expressions are derived to predict the maximum bit resolution of the phase shifter from the scaling factor of the coarse and fine vector-scaling stages. The phase shifter was designed and fabricated using the standard 130-nm CMOS process and was tested on-wafer over the frequency range of 4.9–5.9 GHz. The phase shifter delivers root mean square (rms) phase and amplitude errors of 1.25° and 0.7 dB, respectively, at the midband frequency of 5.4 GHz. The input and output return losses are both below 17 dB over the band, and the insertion loss is better than 4 dB over the band. The circuit uses an area of 0.303 mm2 excluding bonding pads and draws 28 mW from a 1.2 V supply.

Transmission network expansion planning considering phase-shifter transformers

This paper presents a novel mathematical model for the transmission network expansion planning problem. Main idea is to consider phase-shifter (PS) transformers as a new element of the transmission system expansion together with other traditional components such as transmission lines and conventional transformers. In this way, PS are added in order to redistribute active power flows in the system and, consequently, to diminish the total investment costs due to new transmission lines. Proposed mathematical model presents the structure of a mixed-integer nonlinear programming (MINLP) problem and is based on the standard DC model. In this paper, there is also applied a specialized genetic algorithm aimed at optimizing the allocation of candidate components in the network. Results obtained from computational simulations carried out with IEEE-24 bus system show an outstanding performance of the proposed methodology and model, indicating the technical viability of using these nonconventional devices during the planning process. Copyright © 2012 Celso T. Miasaki et al.

Achromatic optical phase shifter/modulator

We propose and demonstrate, theoretically and experimentally, a novel achromatic optical phase shifter modulator based on a frequency-domain optical delay line configured to maintain zero group delay as variable phase delay is generated by means of tilting a mirror. Compared with previously reported phase shifter modulators, e.g., based on the Pancharatnam (geometric) phase, our device is high speed and polarization insensitive and produces a large, bounded phase delay that, uniquely, is one-to-one mapped to a measurable parameter, the tilt angle.

Estudo da estabilidade a pequenas perturbações do sistema elétrico de potência sob a ação do dispositivo FACTS PHASE SHIFTER - PS

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Development of a slow-wave MEMS phase shifter on CMOS technology for millimeter wave frequencies

We propose a slow-wave MEMS phase shifter that can be fabricated using the CMOS back-end and an additional maskless post-process etch. The tunable phase shifter concept is formed by a conventional slow-wave transmission line. The metallic ribbons that form the patterned floating shield of this type of structure are released to allow motion when a control voltage is applied, which changes the characteristic impedance and the phase velocity. For this device a quality factor greater than 40 can be maintained, resulting in a figure of merit on the order of 0.7 dB/360 degrees and a total area smaller than 0.14 mm(2) for a 60-GHz working frequency. (C) 2011 Elsevier B.V. All rights reserved.

Surgical treatment of globe subluxation in the active phase of the myogenic type of Graves orbitopathy: case reports

The purpose of the present article is to present and discuss two cases of globe subluxation in the active phase of myogenic Graves' orbitopathy and to evaluate the prevalence of this phenomenon. Two patients with the myogenic variant of Graves' orbitopathy that had being treated with oral and intravenous steroid pulses developed globe subluxation. Both had to have urgent eyelid and orbital decompression. After these observations, we reviewed the medical records of a sample of 284 patients (482 orbits) who had had orbital decompression at our Institution from 1992 to 2010, with a search for cases presenting severe proptosis or globe subluxation in the active phase of myogenic Graves' orbitopathy. No patient had to have decompression for globe subluxation in the active phase of Graves' orbitopathy. The prevalence of this event as an indication for surgery in the myogenic variant of Graves' orbitopathy was therefore 0.7% (2/284) or even less. The combination of lowering the upper eyelid and orbital decompression had a dramatic therapeutic effect on these patients despite the presence of intense inflammatory signs in the orbits. In conclusion, patients affected with the myogenic variant of Graves' orbitopathy may develop globe subluxation. Urgent surgical treatments should not be postponed despite the presence of active inflammation.

Study of an electronic steering antenna with a staggered phase shifter configuration

This paper presents a study of three possible solutions that can be taken into account to control the phase shift between elements in an antenna array. Because commercial digital phase shifters have become a strategic element by U.S. Government, these elements have increased their price. For this reason, it is necessary to adopt some solutions that allow us to deal with the design and construction of antenna arrays.

Effect of preparation conditions on the formation of the active phase of carbon fiber catalytic systems for the low-temperature oxidation of carbon monoxide

We studied the effects of the composition of impregnating solution and heat treatment conditions on the activity of catalytic systems for the low-temperature oxidation of CO obtained by the impregnation of Busofit carbon-fiber cloth with aqueous solutions of palladium, copper, and iron salts. The formation of an active phase in the synthesized catalysts at different stages of their preparation was examined with the use of differential thermal and thermogravimetric analyses, X-ray diffraction analysis, X-ray photoelectron spectroscopy, and elemental spectral analysis. The catalytic system prepared by the impregnation of electrochemically treated Busofit with the solutions of PdCl, FeCl, CuBr, and Cu(NO ) and activated under optimum conditions ensured 100% CO conversion under a respiratory regime at both low (0.03%) and high (0.5%) carbon monoxide contents of air. It was found that the activation of a catalytic system at elevated temperatures (170-180°C) leads to the conversion of Pd(II) into Pd(I), which was predominantly localized in a near-surface layer. The promoting action of copper nitrate consists in the formation of a crystalline phase of the rhombic atacamite CuCl(OH). The catalyst surface is finally formed under the conditions of a catalytic reaction, when a joint Pd(I)-Cu(I) active site is formed. © 2014 Pleiades Publishing, Ltd.

Identifying the active phase in Cs-promoted MgO nanocatalysts for triglyceride transesterification

Background: Biodiesel is a clean-burning, renewable and biodegradable diesel fuel substitute derived from animal fats and plant oils, which may play an important role in replacing diminishing fossil fuel reserves and combating climate change. Conventional biodiesel production uses soluble base catalysts, such as Na or K alkoxides, to convert oils into fuel, and as a result requires energy intensive aqueous quench cycles to isolate the biodiesel product. Results: Cs-doping nanoparticulate MgO, prepared via a novel, supercritical sol-gel method, yields a solid base catalyst with improved activity for the transesterification of pure triacylglycerides (TAGs) and olive oil. Conclusion: Here, X-ray absorption spectroscopy (XAS) is used to probe the local chemical environment of Cs atoms in order to identify the nature of the catalytically active species as CsMg(CO)(HO). © 2013 Society of Chemical Industry.

Highly dispersed Ptδ+ on TixCe(1−x)O2 as an active phase in preferential oxidation of CO

Structure–activity relationships for 1 wt.% Pt catalysts were investigated for a series of TixCe(1−x)O2 (x = 1, 0.98, 0.9, 0.5, 0.2 and 0) supports prepared by the sol–gel method. The catalysts prepared by impregnation were characterized in detail by applying a wide range of techniques as N2-isotherms, XRF, XRD, Raman, XPS, H2-TPR, Drifts, UV–vis, etc. and tested in the preferential oxidation of CO in the presence of H2. Also several reaction conditions were deeply analyzed. A strong correlation between catalyst performance and the electronic properties let us to propose, based in all the experimental results, a plausible reaction mechanism where several redox cycles are involved.

Contribución a los arrays de antenas activos en microondas = Contribution to active array antennas at microwave bands

Esta tesis que tiene por título "Contribución a los arrays de antenas activos en banda X", ha sido desarrollada por el estudiante de doctorado Gonzalo Expósito Domínguez, ingeniero de telecomunicación en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Castañer y José Manuel Fernández González. Esta tesis contiene un profundo estudio del arte en materia de antenas activas en el campo de apuntamiento electrónico. Este estudio comprende desde los fundamentos de este tipo de antenas, problemas de operación y limitaciones hasta los sistemas actuales más avanzados. En ella se identifican las partes críticas en el diseño y posteriormente se llevan a la práctica con el diseño, simulación y construcción de un subarray de una antena integrada en el fuselaje de un avión para comunicaciones multimedia por satélite que funciona en banda X. El prototipo consta de una red de distribución multihaz de banda ancha y una antena planar. El objetivo de esta tesis es el de aplicar nuevas técnicas al diseño de antenas de apuntamiento electrónico. Es por eso que las contribuciones originales son la aplicación de barreras electromagnéticas entre elementos radiantes para reducir los acoplamientos mutuos en arrays de exploración electrónica y el diseño de redes desfasadoras sencillas en las que no son necesarios complejos desfasadores para antenas multihaz. Hasta la fecha, las barreras electromagnéticas, Electronic Band Gap (EBG), se construyen en sustratos de permitividad alta con el fin de aumentar el espacio disponible entre elementos radiantes y reducir el tamaño de estas estructuras. Sin embargo, la utilización de sustratos de alta permitividad aumenta la propagación por ondas de superficie y con ellas el acoplo mutuo. Utilizando sustratos multicapa y colocando la vía de las estructuras en su borde, en vez de en su centro, se consigue reducir el tamaño sin necesidad de usar sustratos de alta permitividad, reducir la eficiencia de radiación de la antena o aumentar la propagación por ondas de superficie. La última parte de la tesis se dedica a las redes conmutadoras y desfasadoras para antenas multihaz. El diseño de las redes de distribución para antenas son una parte crítica ya que se comportan como un atenuador a la entrada de la cadena receptora, modificando en gran medida la figura de ruido del sistema. Las pérdidas de un desfasador digital varían con el desfase introducido, por ese motivo es necesario caracterizar y calibrar los dispositivos correctamente. Los trabajos presentados en este manuscrito constan de un desfasador reflectivo con un conmutador doble serie paralelo para igualar las pérdidas de inserción en los dos estados y también un conmutador de una entrada y dos salidas cuyos puertos están adaptados en todo momento independientemente del camino del conmutador para evitar las reflexiones y fugas entre redes o elementos radiantes. El tomo finaliza con un resumen de las publicaciones en revistas científicas y ponencias en congresos, nacionales e internacionales, el marco de trabajo en el que se ha desarrollado, las colaboraciones que se han realizado y las líneas de investigación futuras. ABSTRACT This thesis was carried out in the Radiation Group of the Signals, Systems and Radiocomunications department of ETSI de Telecomunicación from Technical University of Madrid. Its title is "Contribution to active array antennas at X band" and it is developed by Gonzalo Expósito Domínguez, Electrical Engineer MsC. under the supervision of Prof. Dr. Manuel Sierra Castañer and Dr. José Manuel Fernández González. This thesis is focused on active antennas, specifically multibeam and electronic steering antenas. In the first part of the thesis a thorough description of the state of the art is presented. This study compiles the fundamentals of this antennas, operation problems and limits, up to the breakthrough applications. The critical design problems are described to use them eventually in the design, simulation and prototyping of an airborne steering array antenna for satellite communication at X band. The main objective of this thesis is to apply new techniques to the design of electronically steering antennas. Therefore the new original contributions are the application of Electromagnetic Band Gap materials (EBG) between radiating elements to reduce the mutual coupling when phase shift between elements exist and phase shifting networks where special characteristics are required. So far, the EBG structures have been constructed with high permitivity substrates in order to increase the available space between radiating elements and reduce the size of the structures. However, the surface wave propagation modes are enhanced and therefore the mutual coupling increases when high permitivity substrates are used. By using multilayered substrates and edge location via, the size is reduced meanwhile low permitivity substrates are used without reducing the radiation efficiency or enhancing the surface propagation modes. The last part of the thesis is focused on the phase shifting distribution networks for multibeam antennas. This is a critical part in the antenna design because the insertion loss in the distribution network behaves as an attenuator located in the first place in a receiver chain. The insertion loss will affect directly to the receiver noise figure and the insertion loss in a phase shifter vary with the phase shift. Therefore the devices must be well characterized and calibrated in order to obtain a properly operation. The work developed in this thesis are a reflective phase shifter with a series-shunt switch in order to make symmetrical the insertion loss for the two states and a complex Single Pole Double Through (SPDT) with matched ports in order to reduce the reflections and leakage between feeding networks and radiating elements. The end of this Ph D. dissertation concludes with a summary of the publications in national and international conferences and scientific journals, the collaborations carried out along the thesis and the future research lines.

Contribution to active multi-beam reconfigurable antennas for L and S bands

La presente tesis doctoral con título "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands" ha sido desarrollada por el investigador ingeniero de telecomunicación estudiante de doctorado Javier García-Gasco Trujillo en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Pérez y José Manuel Fernández González. Durante décadas, el desarrollo de antenas de apuntamiento electrónico ha estado limitado al área militar. Su alto coste y su gran complejidad eran los mayores obstáculos que frenaban la introducción de esta tecnología en aplicaciones comerciales de gran escala. La reciente aparición de componentes de estado sólido prácticos, fiables, y de bajo coste ha roto la barrera del coste y ha reducido la complejidad, haciendo que las antenas reconfigurables de apuntamiento electrónico sean una opción viable en un futuro cercano. De esta manera, las antenas phased array podrían llegar a ser la joya de la corona que permitan alcanzar los futuros retos presentes en los sistemas de comunicaciones tanto civiles como militares. Así pues, ahora es el momento de investigar en el desarrollo de antenas de apuntamiento electrónico de bajo coste, donde los nuevos componentes de estado sólido comerciales forman el núcleo duro de la arquitectura. De esta forma, el estudio e implementación de estos arrays de antenas activas de apuntamiento electrónico capaces de controlar la fase y amplitud de las distintas señales implicadas es uno de los grandes retos de nuestro tiempo. Esta tesis se enfrenta a este desafío, proponiendo novedosas redes de apuntamiento electrónico e innovadores módulos de transmisión/recepción (T/R) utilizando componentes de estado sólido de bajo coste, que podrán integrar asequibles antenas activas reconfigurables multihaz en bandas L y S. En la primera parte de la tesis se realiza una descripción del estado del arte de las antenas phased array, incluyendo su base teórica y sus ventajas competitivas. Debido a que las contribuciones obtenidas en la presente tesis han sido realizadas dentro de distintos proyectos de investigación, donde se han manejada antenas de simple/doble polarización circular y simple/doble banda de trabajo, se describen detenidamente los dos proyectos más relevantes de la investigación: el radar de basura espacial de la Agencia Espacial Europea (ESA), Space Situational Awareness (SSA); y la estación base de seguimiento y control de satélites de órbita baja, GEOdesic Dome Array (GEODA). Sin lugar a dudas, los dispositivos desfasadores son uno de los componentes clave en el diseño de antenas phased arrays. Recientemente se ha observado una gran variación en el precio final de estos dispositivos, llegando en ocasiones a límites inasequibles. Así pues, se han propuesto distintas técnicas de conformación de haz alternativas a la utilización de componentes desfasadores comerciales: el desfasador de líneas conmutadas, la red de haz conmutado, y una novedosa red desfasadora divisora/combinadora de potencia. Para mostrar un uso práctico de las mismas, se ha propuesto el uso de las tres alternativas para el caso práctico del subarray de cinco elementos de la celda GEODA-SARAS. Tras dicho estudio se obtiene que la novedosa red desfasadora divisora/combinadora de potencia propuesta es la que mejor relación comportamiento/coste presenta. Para verificar su correcto funcionamiento se construye y mide los dos bloques principales de los que está compuesta la red total, comprobando que en efecto la red responde según lo esperado. La estructura más simple que permite realizar un barrido plano es el array triangular de tres elementos. Se ha realizado el diseño de una nueva red multihaz que es capaz de proporcionar tres haces ortogonales en un ángulo de elevación _0 y un haz adicional en la dirección broadside utilizando el mencionado array triangular de tres elementos como antena. En primer lugar se realizar una breve introducción al estado del arte de las redes clásicas multihaz. Así mismo se comentan innovadores diseños de redes multihaz sin pérdidas. El estudio da paso a las redes disipativas, de tal forma que se analiza su base matemática y se muestran distintas aplicaciones en arrays triangulares de tres elementos. Finalmente, la novedosa red básica propuesta se presenta, mostrando simulaciones y medidas de la misma para el caso prácticoo de GEODA. También se ha diseñado, construido y medido una red compuesta por dos redes básicas complementarias capaz de proporcionar seis haces cuasi-ortogonales en una dirección _0 con dos haces superpuestos en broadside. La red propuesta queda totalmente validada con la fabricación y medida de estos con prototipos. Las cadenas de RF de los módulos T/R de la nueva antena GEODA-SARAS no son algo trivial. Con el fin de mostrar el desarrollo de una cadena compleja con una gran densidad de componentes de estado sólido, se presenta una descripción detallada de los distintos componentes que integran las cadenas de RF tanto en transmisión como en recepción de la nueva antena GEODA-SARAS. Tras presentar las especificaciones de la antena GEODA-SARA y su diagrama de bloques esquemático se describen los dos bloques principales de las cadenas de RF: la celda de cinco elementos, y el módulo de conversión de panel. De la misma manera también se presentará el módulo de calibración integrado dentro de los dos bloques principales. Para comprobar que el funcionamiento esperado de la placa es el adecuado, se realizará un análisis que tratará entre otros datos: la potencia máxima en la entrada del transmisor (comprobando la saturación de la cadena), señal de recepción mínima y máxima (verificando el rango de sensibilidad requerido), y el factor G/T (cumpliendo la especificación necesaria). Así mismo se mostrará un breve estudio del efecto de la cuantificación de la fase en el conformado de haz de RF. Los estudios muestran que la composición de las cadenas de RF permite el cumplimiento de las especificaciones necesarias. Finalmente la tesis muestra las conclusiones globales del trabajo realizado y las líneas futuras a seguir para continuar con esta línea de investigación. ABSTRACT This PhD thesis named "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands", has been written by the Electrical Engineer MSc. researcher Javier García-Gasco Trujillo in the Grupo de Radiación of the Departamento de Señales, Sistemas y Radiocomunicaciones from the ETSI de Telecomunicación of the Universidad Politécnica de Madrid. For decades, the implementation of electronically steerable phased array antennas was confined to the military area. Their high cost and complexity were the major obstacles to introduce this technology in large scale commercial applications. The recent emergence of new practical, low-cost, and highly reliable solid state devices; breaks the barrier of cost and reduces the complexity, making active phased arrays a viable future option. Thus, phased array antennas could be the crown jewel that allow to meet the future challenges in military and civilian communication systems. Now is time to deploy low-cost phased array antennas, where newly commercial components form the core of the architecture. Therefore, the study and implementation of these novel low-cost and highly efficient solid state phased array blocks capable of controlling signal phase/amplitude accurately is one of the great challenges of our time. This thesis faces this challenge, proposing innovative electronic beam steering networks and transmitter/ receiver (T/R) modules using affordable solid state components, which could integrate fair reconfigurable phased array antennas working in L and S bands. In the first part of the thesis, a description of the state of art of phased array antennas, including their fundamentals and their competitive advantages, is presented. Since thesis contributions have been carried out for different research projects, where antennas with single/double circular polarization and single/double working frequency bands have been examined, frameworks of the two more important projects are detailed: the Space Situational Awareness (SSA) programme from the European Space Agency (ESA), and the GEOdesic Dome Array (GEODA) project from ISDEFE-INSA and the ESA. Undoubtedly, phase shifter devices are one of the key components of phased array antennas. Recent years have witnessed wide fluctuations in commercial phase shifter prices, which sometimes led to unaffordable limit. Several RF steering technique alternatives to the commercial phase shifters are proposed, summarized, and compared: the switched line phase shifter, the switched-beam network, and the novel phase shifter power splitter/combiner network. In order to show a practical use of the three different techniques, the five element GEODA-SARAS subarray is proposed as a real case of study. Finally, a practical study of a newly phase shifter power splitter/combiner network for a subarray of five radiating elements with triangular distribution is shown. Measurements of the two different phase shifter power splitter/combiner prototypes integrating the whole network are also depicted, demonstrating their proper performance. A triangular cell of three radiating elements is the simplest way to obtain a planar scanner. A new multibeam network configuration that provides three orthogonal beams in a desired _0 elevation angle and an extra one in the broadside steering direction for a triangular array of three radiating elements is introduced. Firstly, a short introduction to the state of art of classical multi-beam networks is presented. Lossless network analysis, including original lossless network designs, are also commented. General dissipative network theory as well as applications for array antennas of three radiating elements are depicted. The proposed final basic multi-beam network are simulated, built and measured to the GEODA cell practical case. A combined network that provides six orthogonal beams in a desired _0 elevation angle and a double seventh one in the broadside direction by using two complementary proposed basic networks will be shown. Measurements of the whole system will be also depicted, verifying the expected behavior. GEODA-SARAS T/R module RF chains are not a trivial design. A thorough description of all the components compounding GEODA-SARAS T/R module RF chains is presented. After presenting the general specifications of the GEODA-SARAS antenna and its block diagrams; two main blocks of the RF chains, the five element cell and the panel conversion module, are depicted and analyzed. Calibration module integrated within the two main blocks are also depicted. Signal flow throw the system analyzing critical situations such as maximum transmitted power (testing the chain unsaturation), minimum and maximum receiving signal (verifying sensitivity range), maximum receiver interference signals (assuring a proper reception), and G/T factor (fulfilling the technical specification) are evaluated. Phase quantization error effects are also listed. Finally, the manuscript contains the conclusions drawn of the present research and the future work.

On a size-structured two-phase population model with infinite states-at-birth

In this work we introduce and analyze a linear size-structured population model with infinite states-at-birth. We model the dynamics of a population in which individuals have two distinct life-stages: an “active” phase when individuals grow, reproduce and die and a second “resting” phase when individuals only grow. Transition between these two phases depends on individuals’ size. First we show that the problem is governed by a positive quasicontractive semigroup on the biologically relevant state space. Then we investigate, in the framework of the spectral theory of linear operators, the asymptotic behavior of solutions of the model. We prove that the associated semigroup has, under biologically plausible assumptions, the property of asynchronous exponential growth.

Comparative composition of bacteria in the human intestinal microflora during remission and active ulcerative colitis

Ulcerative colitis is a severe, relapsing and remitting disease of the human large intestine characterised by inflammation of the mucosa and submucosa. The main site of disease is the sigmoid/rectal region of the large bowel but the aetiology remains unknown. There is considerable evidence to indicate that the components of the resident colonic microflora can play an important role in initiation of the disease. The present study was aimed at characterising the faecal microflora of ulcerative colitis patients in remission and active phases to determine profile differences. Faecal samples were obtained from 12 patients, 6 with active colitis and 6 in remission. The samples were analysed for populations of lactobacilli, bifidobacteria, clostridia, bacteroides, sulphate-reducing bacteria (SRB) and total bacteria using culture independent fluorescence in situ hybridisation (FISH). Lactobacillus-specific denaturing gradient gel electrophoresis (DGGE) was then performed to compare the species present. Numbers of lactobacilli were significantly lower (p<0.05) during the active phase of the disease but the other populations tested did not differ. DGGE analysis revealed that Lactobacillus salivarus, Lactobacillus manihotivorans and Pediococcus acidilactici were present in remission, but not during active inflammation. These results imply that a reduction in intestinal Lactobacillus species may be important in the initiation of ulcerative colitis.