Stable pulse-compressed acousto-optic Q-switched fiber laser

A novel acousto-optic switch operation by a simple laser-diode pumped acousto-optic, Q-switched, ytterbium-doped, double-clad fiber laser is reported. Stable compressed Q-switched sub-40 ns pulses with a beam quality factor (M-2 = 2) are achieved at the repetition rate of 1-50 kHz. Q-switched pulses of similar to 20 mu J pulse energy and 35 as pulse width are obtained at the repetition rate of 50 kHz. Finally, a reasonable explanation of the novel Q-switched operation is presented. (c) 2007 Optical Society of America.

Research on Q-Switched Nd : YAG laser engraving

IN this paper, the engraving process with Q-Switched Nd:YAG laser is investigated. High power density is the pre- requisition to vapor materials, and high repetition rate makes the engraving process highly efficient. An acousto- optic Q-Switch is applied in the cavity of CW 200 W Nd:YAG laser to achieve the high peak power density and the high pulse repetition rate. Different shape craters are formed in a patterned structure on the material surface when the laser beam irradiates on it by controlling power density, pulse repetition rate, pulse quantity and pulse interval. In addition, assisting oxygen gas is used for not only improving combustion to deepen the craters but also removing the plasma that generated on the top of craters. Off-focus length classified as negative and positive has a substantial effect on crater diameters. According to the message of rotating angle positions from material to be engraved and the information of graph pixels from computer, a special graph is imparted to the material by integrating the Q- Switched Nd:YAG laser with the computer graph manipulation and the numerically controlled worktable. The crater diameter depends on laser beam divergence and laser focal length. The crater diameter changes from 50 micrometers to 300 micrometers , and the maximum of crater depth reaches one millimeter.

Yb:YAG/YAG复合陶瓷薄片连续和调Q输出特性

采用面泵浦的CAMIL结构，我们研究了970 nm泵浦的Yb:YAG/YAG复合陶瓷薄片激光器，获得了连续和调Q的激光输出。在连续运转情况下，获得了最高1.05 W的激光输出，中心波长为1031 nm，后腔输出镜透射率为2％。我们同时获得了声光调Q的脉冲输出，重复频率从1 kHz到30 kHz，脉宽分别从166 ns到700 ns。

Depolarization loss compensated resonator for electro-optic Q-switched solid-state laser

A novel laser resonator for compensating depolarization loss that is due to thermally induced birefringence in active rod is reported. As this new structure being applied to an electro-optic Q-switched LIDA side-pumped Nd:YAG laser operating at a repetition rate of 1000 Hz, substantial reduction in depolarization loss has been observed, the output pulse energy is improved about 56% from that of a traditional resonator without compensation structure. With incident pump energy of 450 mJ per pulse, linearly polarized output energy of 30 mJ per pulse is achieved, the pulse duration is less than 15 ns, and the peak power of pulse is about 2 MW. The extinction ratio of laser beam is better than 10:1, and the beam divergence is 1.3 mrad with beam diameter of around 2.5 mm. (c) 2006 Published by Elsevier B.V.

高重复频率、窄脉宽全固态光纤放大器种子源

高重复频率、窄脉宽的全固态激光器种子源级联光纤放大器是获得高功率脉冲激光输出的有效手段.短上能态寿命的Nd∶YVO4晶体在连续抽运、高重复频率Q开关工作时容易得到接近连续性能的平均输出功率.理论分析了声光(AO)调Q器件中影响输出能量和脉宽大小的主要因素,优化配置了腔型参数.利用激光二极管(LD)光纤耦合模块端面抽运Nd∶YVO4晶体,实现了声-光调Q重复频率100 kHz以上,脉宽20 ns以下,波长1064 nm的激光输出.在抽运功率5.7 W时,得到了脉宽15.3 ns,重复频率150 kHz的种子光输出,在级联单级光纤放大器后,得到了20 W的输出.

Laser diode array side-pumped acousto-optic induced unidirectional operation Q-switched Nd : YAG slab ring laser

A laser-diode array (LDA) side-pumped Nd:YAG slab ring laser is described that incorporates a prism-shaped acousto-optic modulator to enforce unidirectional operation and Q-switching. When pumped by the maximum power of 50 W, Q-switched energies of 3.6 mJ and 50 ns duration, corresponding to a peak power of 72 kW, are obtained. (C) 1999 Society of Photo-Optical Instrumentation Engineers. [S0091-3286(99)01306-9].

Surface acoustic wave distribution and acousto-optic interaction in proton exchanged LiNbO3 waveguides

The efficiency of acoustooptic (AO) interaction in YZ-cut proton exchanged (PE) LiNbO3 waveguides is theoretically analysed by determining the overlap between the optical and acoustic field distributions. The present analysis takes into account the perturbed SAW field distribution due to the presence of the PE layer on the LiNbO3 substrate determined by the rigorous layered medium approach. The overlap is found to be significant upto very high acoustic frequencies of the order of 5 GHz, whereas in the earlier analysis by vonHelmolt and Schaffer [6] for diffused waveguides, it was shown that the overlap integral rolls down to nearly zero at this high frequency range.

A laser-diode-pumped acoustic-optic Q-switched Nd:YVO4 slab laser with a hybrid resonator

A 32.1 W laser-diode-stack pumped acoustic-optic Q-switched Nd:YVO4 slab laser with hybrid resonator at 1064 nm was demonstrated with the pumping power of 112 W and repetition rate of 40 kHz, the pulse duration was 32.47 ns. The slope efficiency and optical-to-optical efficiency were 37 and 28.7%, respectively. At the repetition rate of 20 kHz and pumping power of 90 W, the average output power and pulse duration were 20.4 W and 20.43 ns, respectively. With the pumping power of 112 W, the beam quality M-2 factors in CW operation were measured to be 1.3 in stable direction and 1.6 in unstable direction.

双调Q开关热退偏补偿全固态激光器

为了有效地补偿激光二极管(LD)侧向抽运1000 Hz重复率电光调Q Nd:YAG激光器棒状增益介质内存在的热致双折射损耗，设计了一种新颖的双调Q晶体开关复合谐振腔结构。实验结果表明，设计的双调Q晶体开关结构Nd:YAG激光器输出激光脉冲能量比单调Q晶体开关结构的非补偿腔输出能量提高了56%，当侧面抽运半导体激光器输出功率达到450 W时，激光输出达到30 mJ/pulse，输出光束偏振度优于10:1，激光脉冲宽度约14 ns。并获得6.7%的光-光转换效率。通过对双调Q开光激光谐振腔进行建模，并用求解速

采用国产双包层光纤的声光调Q激光器

实验报道采用我国自行设计的大模场掺镱双包层光纤，利用简单声光调Q装置，成功实现调Q运转；在1－50kHz调制频率下获得了百纳秒的调Q脉冲，其输出光束质量因子大约为2。当重复频率为1kHz时，获得了脉冲宽度为132ns，能量0.93mJ。同时实验中观察到的调Q脉冲常出现一点锁模现象，针对这一现象进行了讨论。

Kilohertz electro-optic Q-switched Nd : YAG ceramic laser

We investigate the lasing characteristics of a laser-diode-array side-pumped electro-optic Q-switched Nd:Y3Al5O12 ceramic laser operating at 1000 Hz pulse repetition rate. Using a YAG poltcrystalline rod with Nd3+ concentration at 1 at.% as the gain medium, pumping with 808 nm laser-diode-arrays, the Q-switched laser output at 1064 nm wavelength with 23 mJ pulse energy and less than 12 ns FWHM pulse width are obtained at a pumping power of about 400 W, the slope efficiency is around 15%, the output beam divergence angle is about 1.2 mrad.

Mode competition in acousto-optically Q-switched planar waveguide lasers

Multi-mode rate equations have been developed to investigate mode competition in high-power acousto-optically Q-switched planar waveguide lasers. The mode competition arises from coupling effects and temporal losses in the transform between guided modes and free-space propagation. Pulse-to-pulse instability and temporal beam distortions are enlarged by mode competition when the laser works in the multi-mode regime. The influence of parasitic oscillation is also discussed. A Nd:YAG planar waveguide laser has been established with a folded hybrid/unstable resonator. A maximum average power of 83 W with a beam propagation factor M-x(2) x M-y(2) = 1.2 x 1.4 is obtained. The theoretical simulation agrees well with the experimental observation. (c) 2006 Elsevier Ltd. All rights reserved.

A silicon-on-insulator-based thermo-optic waveguide switch with low insertion loss and fast response

A silicon-on-insulator-based thermo-optic waveguide switch integrated with spot size converters is designed and fabricated by inductively coupled plasma reactive ion etching. The device shows good characteristics, including low, insertion loss of 8 +/- 1 dB for wavelength 1530-1580 nm and fast response times of 4.6 As for rising edge and 1.9 mu s for failing edge. The extinction ratios of the two channels are 19.1 and 18 dB, respectively.

SOI-based 16x16 thermo-optic waveguide switch matrix

A 16 x 16 thermo-optic wavelenght switch matrix has been designed and febricated on silicon-on-insulator wafer. For reducing device lenght, blocking switch matrix configuration is chosen. The building block of a matix is a 2 x 2 cell with Mach-Zehnder interferometer configuration, where a multi-mode interferometer serves as splitters/combiners. Spot size converters and isolating grooves are integrated on the same chip to reduce loss and power consumption. Average power consumption of the switch cell is 220 mW. The switching time of a switch cell is less than 3 mu s.