A comparison of self-nominated and actual speeds in work zones

Despite significant research on drivers’ speeding behavior in work zones, little is known about how well drivers’ judgments of appropriate speeds match their actual speeds and what factors influence their judgments. This study aims to fill these two important gaps in the literature by comparing observed speeds in two work zones with drivers’ self-nominated speeds for the same work zones. In an online survey, drivers nominated speeds for the two work zones based on photographs in which the actual posted speed limits were not revealed. A simultaneous equation modelling approach was employed to examine the effects of driver characteristics on their self-nominated speeds. The results showed that survey participants nominated lower speeds (corresponding to higher compliance rates) than those which were observed. Higher speeds were nominated by males than females, young and middle aged drivers than older drivers, and drivers with truck driving experience than those who drive only cars. Larger differences between nominated and observed speeds were found among car drivers than truck drivers. These differences suggest that self-nominated speeds might not be valid indicators of the observed work zone speeds and therefore should not be used as an alternative to observed speed data.

Admission control schemes for TCP elastic traffic in class-based networks

En aquesta tesi proposem dos esquemes de xarxa amb control d'admissió per al trànsit elàstic TCP amb mecanismes senzills. Ambdós esquemes són capaços de proporcionar throughputs diferents i aïllament entre fluxos, on un "flux" es defineix com una seqüència de paquets relacionats dins d'una connexió TCP. Quant a l'arquitectura, ambdós fan servir classes de paquets amb diferents prioritats de descart, i un control d'admissió implícit, edge-to-edge i basat en mesures. En el primer esquema, les mesures són per flux, mentre que en el segon, les mesures són per agregat. El primer esquema aconsegueix un bon rendiment fent servir una modificació especial de les fonts TCP, mentre que el segon aconsegueix un bon rendiment amb fonts TCP estàndard. Ambdós esquemes han estat avaluats satisfactòriament a través de simulació en diferents topologies de xarxa i càrregues de trànsit.

Sustainable Air Traffic Management System Development Methodology

As it is defined in ATM 2000+ Strategy (Eurocontrol 2001), the mission of the Air Traffic Management (ATM) System is: “For all the phases of a flight, the ATM system should facilitate a safe, efficient, and expedite traffic flow, through the provision of adaptable ATM services that can be dimensioned in relation to the requirements of all the users and areas of the European air space. The ATM services should comply with the demand, be compatible, operate under uniform principles, respect the environment and satisfy the national security requirements.” The objective of this paper is to present a methodology designed to evaluate the status of the ATM system in terms of the relationship between the offered capacity and traffic demand, identifying weakness areas and proposing solutions. The first part of the methodology relates to the characterization and evaluation of the current system, while a second part proposes an approach to analyze the possible development limit. As part of the work, general criteria are established to define the framework in which the analysis and diagnostic methodology presented is placed. They are: the use of Air Traffic Control (ATC) sectors as analysis unit, the presence of network effects, the tactical focus, the relative character of the analysis, objectivity and a high level assessment that allows assumptions on the human and Communications, Navigation and Surveillance (CNS) elements, considered as the typical high density air traffic resources. The steps followed by the methodology start with the definition of indicators and metrics, like the nominal criticality or the nominal efficiency of a sector; scenario characterization where the necessary data is collected; network effects analysis to study the relations among the constitutive elements of the ATC system; diagnostic by means of the “System Status Diagram”; analytical study of the ATC system development limit; and finally, formulation of conclusions and proposal for improvement. This methodology was employed by Aena (Spanish Airports Manager and Air Navigation Service Provider) and INECO (Spanish Transport Engineering Company) in the analysis of the Spanish ATM System in the frame of the Spanish airspace capacity sustainability program, although it could be applied elsewhere.

Maintenance and construction zone: annotated bibliography. Interim report.

Texas State Department of Highways and Public Transportation, Transportation Planning Division, Austin

Traffic operations control for older drivers. Final report.

Federal Highway Administration, Office of Safety and Traffic Operations Research and Development, McLean, Va.

FAA staffing : challenges in managing shortages in the maintenance work force : report to congressional requesters /

"B-228783"--P. [1].

Benefits of all work and no play: The relationship between neuroticism and performance as a function of resource allocation

The authors evaluate a model suggesting that the performance of highly neurotic individuals, relative to their stable counterparts, is more strongly influenced by factors relating to the allocation of attentional resources. First, an air traffic control simulation was used to examine the interaction between effort intensity and scores on the Anxiety subscale of Eysenck Personality Profiler Neuroticism in the prediction of task performance. Overall effort intensity enhanced performance for highly anxious individuals more so than for individuals with low anxiety. Second, a longitudinal field study was used to examine the interaction between office busyness and Eysenck Personality Inventory Neuroticism in the prediction of telesales performance. Changes in office busyness were associated with greater performance improvements for highly neurotic individuals compared with less neurotic individuals. These studies suggest that highly neurotic individuals outperform their stable counterparts in a busy work environment or if they are expending a high level of effort.

Optimization of adaptive traffic signal control with transit signal priority at isolated intersections using parallel genetic algorithms

Optimization of adaptive traffic signal timing is one of the most complex problems in traffic control systems. This dissertation presents a new method that applies the parallel genetic algorithm (PGA) to optimize adaptive traffic signal control in the presence of transit signal priority (TSP). The method can optimize the phase plan, cycle length, and green splits at isolated intersections with consideration for the performance of both the transit and the general vehicles. Unlike the simple genetic algorithm (GA), PGA can provide better and faster solutions needed for real-time optimization of adaptive traffic signal control. ^ An important component in the proposed method involves the development of a microscopic delay estimation model that was designed specifically to optimize adaptive traffic signal with TSP. Macroscopic delay models such as the Highway Capacity Manual (HCM) delay model are unable to accurately consider the effect of phase combination and phase sequence in delay calculations. In addition, because the number of phases and the phase sequence of adaptive traffic signal may vary from cycle to cycle, the phase splits cannot be optimized when the phase sequence is also a decision variable. A "flex-phase" concept was introduced in the proposed microscopic delay estimation model to overcome these limitations. ^ The performance of PGA was first evaluated against the simple GA. The results show that PGA achieved both faster convergence and lower delay for both under- or over-saturated traffic conditions. A VISSIM simulation testbed was then developed to evaluate the performance of the proposed PGA-based adaptive traffic signal control with TSP. The simulation results show that the PGA-based optimizer for adaptive TSP outperformed the fully actuated NEMA control in all test cases. The results also show that the PGA-based optimizer was able to produce TSP timing plans that benefit the transit vehicles while minimizing the impact of TSP on the general vehicles. The VISSIM testbed developed in this research provides a powerful tool to design and evaluate different TSP strategies under both actuated and adaptive signal control. ^

The Machine Vision Toolbox : A MATLAB Toolbox for vision and vision-based control

The article described an open-source toolbox for machine vision called Machine Vision Toolbox (MVT). MVT includes more than 60 functions including image file reading and writing, acquisition, display, filtering, blob, point and line feature extraction, mathematical morphology, homographies, visual Jacobians, camera calibration, and color space conversion. MVT can be used for research into machine vision but is also versatile enough to be usable for real-time work and even control. MVT, combined with MATLAB and a model workstation computer, is a useful and convenient environment for the investigation of machine vision algorithms. The article illustrated the use of a subset of toolbox functions for some typical problems and described MVT operations including the simulation of a complete image-based visual servo system.

Empirical analysis of freeway traffic oscillation : its safety impact and evolution

Traffic oscillations are typical features of congested traffic flow that are characterized by recurring decelerations followed by accelerations. However, people have limited knowledge on this complex topic. In this research, 1) the impact of traffic oscillations on freeway crash occurrences has been measured using the matched case-control design. The results consistently reveal that oscillations have a more significant impact on freeway safety than the average traffic states. 2) Wavelet Transform has been adopted to locate oscillations' origins and measure their characteristics along their propagation paths using vehicle trajectory data. 3) Lane changing maneuver's impact on the immediate follower is measured and modeled. The knowledge and the new models generated from this study could provide better understanding on fundamentals of congested traffic; enable improvements to existing traffic control strategies and freeway crash countermeasures; and instigate people to develop new operational strategies with the objective of reducing the negative effects of oscillatory driving.

Asphalt concrete surfaces macrotexture determination from still images

Road surface macrotexture is identified as one of the factors contributing to the surface's skid resistance. Existing methods of quantifying the surface macrotexture, such as the sand patch test and the laser profilometer test, are either expensive or intrusive, requiring traffic control. High-resolution cameras have made it possible to acquire good quality images from roads for the automated analysis of texture depth. In this paper, a granulometric method based on image processing is proposed to estimate road surface texture coarseness distribution from their edge profiles. More than 1300 images were acquired from two different sites, extending to a total of 2.96 km. The images were acquired using camera orientations of 60 and 90 degrees. The road surface is modeled as a texture of particles, and the size distribution of these particles is obtained from chord lengths across edge boundaries. The mean size from each distribution is compared with the sensor measured texture depth obtained using a laser profilometer. By tuning the edge detector parameters, a coefficient of determination of up to R2 = 0.94 between the proposed method and the laser profilometer method was obtained. The high correlation is also confirmed by robust calibration parameters that enable the method to be used for unseen data after the method has been calibrated over road surface data with similar surface characteristics and under similar imaging conditions.

An investigation on multi-vehicle motorcycle crashes using log-linear models

Motorcyclists are the most crash-prone road-user group in many Asian countries including Singapore; however, factors influencing motorcycle crashes are still not well understood. This study examines the effects of various roadway characteristics, traffic control measures and environmental factors on motorcycle crashes at different location types including expressways and intersections. Using techniques of categorical data analysis, this study has developed a set of log-linear models to investigate multi-vehicle motorcycle crashes in Singapore. Motorcycle crash risks in different circumstances have been calculated after controlling for the exposure estimated by the induced exposure technique. Results show that night-time influence increases crash risks of motorcycles particularly during merging and diverging manoeuvres on expressways, and turning manoeuvres at intersections. Riders appear to exercise more care while riding on wet road surfaces particularly during night. Many hazardous interactions at intersections tend to be related to the failure of drivers to notice a motorcycle as well as to judge correctly the speed/distance of an oncoming motorcycle. Road side conflicts due to stopping/waiting vehicles and interactions with opposing traffic on undivided roads have been found to be as detrimental factors on motorcycle safety along arterial, main and local roads away from intersections. Based on the findings of this study, several targeted countermeasures in the form of legislations, rider training, and safety awareness programmes have been recommended.

Empirical IEEE 802.11p performance evaluation on test tracks

IEEE 802.11p is the new standard for inter-vehicular communications (IVC) using the 5.9 GHz frequency band; it is planned to be widely deployed to enable cooperative systems. 802.11p uses and performance have been studied theoretically and in simulations over the past years. Unfortunately, many of these results have not been confirmed by on-tracks experimentation. In this paper, we describe field trials of 802.11p technology with our test vehicles. Metrics such as maximum range, latency and frame loss are examined.

Examination of relationships and mediating effects of self-efficacy, locus of control, coping and the practice environment on caring efficacy and job satisfaction in Australian registered nurses

Background to the Problem: Improving nurses' self-efficacy and job satisfaction may improve the quality of nursing care to patients. Moreover, to work effectively and consistently with professional nursing standards, nurses have to believe they are able to make decisions about their practice. In order to identify what strategies and professional development programmes should be developed and implemented for registered nurses in the Australian context, a comprehensive profile of registered nurses and factors that affect nursing care in Australia needs to be available. However, at present, there is limited information available on a) the perceived caring efficacy and job satisfaction of registered nurses in Australia, and b) the relationships between the demographic variables general self-efficacy, work locus of control, coping styles, the professional nursing practice environment and caring efficacy and job satisfaction of registered nurses in Australia. This is the first study to 1) investigate relationships between caring efficacy and job satisfaction with factors such as general self-efficacy, locus of control and coping, 2) the nursing practice environment in the Australian context and 3) conceptualise a model of caring efficacy and job satisfaction in the Australian context. Research Design and Methods: This study used a two-phase cross-sectional survey design. A pilot study was conducted in order to determine the validity and reliability of the survey instruments and to assess the effectiveness of the participant recruitment process. The second study of the research involved investigating the relationships between the socio-demographic, dependent and independent variables. Socio-demographic variables included age, gender, level of education, years of experience, years in current job, employment status, geographical location, specialty area, health sector, state and marital status. Other independent variables in this study included general self-efficacy, work locus of control, coping styles and the professional nursing practice environment. The dependent variables were job satisfaction and caring efficacy. Results: A confirmatory factor analysis of the Brisbane Practice Environment Measure (B-PEM) was conducted. A five-factor structure of the B-PEM was confirmed. Relationships between socio-demographic variables, caring efficacy and job satisfaction, were identified at the bivariate and multivariable levels. Further, examination using structural equation modelling revealed general self-efficacy, work locus of control, coping style and the professional nursing practice environment contributed to caring efficacy and job satisfaction of registered nurses in Australia. Conclusion: This research contributes to the literature on how socio-demographic, personal and environmental variables (work locus of control, general self-efficacy and the nursing practice environment) influence caring efficacy and job satisfaction in registered nurses in Australia. Caring efficacy and job satisfaction may be improved if general self-efficacy is high in those that have an internal work locus of control. The study has also shown that practice environments that provide the necessary resources improve job satisfaction in nurses. The results have identified that the development and implementation of strategies for professional development and orientation programmes that enhance self-efficacy and work locus of control may contribute to better quality nursing practice and job satisfaction. This may further assist registered nurses towards focusing on improving their practice abilities. These strategies along with practice environments that provide the necessary resources for nurses to practice effectively may lead to better job satisfaction. This information is important for nursing leaders, healthcare organisations and policymakers, as the development and implementation of these strategies may lead to better recruitment and retention of nurses. The study results will contribute to the national and international literature on self-efficacy, job satisfaction and nursing practice.

What relationships exist between general self efficacy, locus of control and the nursing practice environment and caring efficacy and job satisfaction?

Research Question: What relationships exist between general self efficacy, locus of control and the nursing practice environment and caring efficacy and job satisfaction? Background: Important characteristics of current nursing practice include nurses having the ability to develop and continue therapeutic relationships with patients, nurses having autonomy and control over the practice environment and nurses having more involvement in decision making. In addition, employee satisfaction is enhanced when organisations offer access to authority. Despite this, nurses continue to complain of feeling powerless in their ability to make decisions. Sample: The study population and criteria for selection included Registered Nurses in Australia who were at the time members of an Australian professional and industrial organisation. Methods: A cross-sectional survey was undertaken. Data analysis was conducted using descriptive and bivariate statistics, and structural equation modeling. Results: The model fit the data well (χ² = 2.3594, χ²/df = 2.3594 and CFI = 0.9987). Twenty four percent of variation in caring efficacy (CE) can be accounted for by general self-efficacy (GSE); work locus of control (WLC) and practice environment (PE) and 62% of the variation in job satisfaction (JS) can be accounted for by GSE, WLC and PE. All pathways were found to be significant except PE to CE. GSE positively explained CE (β = 0.38). WLC was negatively related to CE i.e., as CE scores increased WLC scores decreased (β = -0.23). Further testing of the model found CE was positively related to GSE (βZ = 0.38, p < 0.001) and negatively related to WLC (βZ = - 0.23, p = 0.001). PE was not significantly associated with CE (βZ = - 0.01, p = 0.85). JS was explained by PE, which was positively related (βZ = 0.69, p = < 0.001); GSE which was negatively related (βZ - 0 .09, p < 0.001) and WLC, which was also negatively related (βZ = - 0.20, p < 0.001). Implications for Practice Nursing and organisational leaders should ensure the development of strategies for professional development and orientation programmes which may enhance nurses’ ability to develop caring relationships and express caring behaviours to their patients and as a result improve organisational and patient outcomes. Nursing shortages and turnover rates are associated with job satisfaction and the nursing practice environment. Improving the nursing environment can produce benefits to the health system such as better job satisfaction, improved workforce retention and better patient outcomes.