Estudio del abastecimiento energético para un barrio modelo utilizando cogeneración con pila de combustible

El alcance del proyecto es describir las directrices técnicas, la definición de criterios, y la estrategia de suministro de energía (Electricidad. Calefacción y Agua Caliente Sanitaria (ACS)) a un barrio modelo situado en un entorno urbano. De inicio se estudia los diversos modelos energéticos atendiendo a la normativa y tecnología, que se pueden aplicar en un conjunto residencial, dando como resultado el modelo propuesto de abastecimiento energético, mediante calefacción de distrito, que incorporara el diseño de una planta de producción de energía termo-eléctrica o Central de Energías basada en la tecnología de condensación de baja temperatura para calefacción y A.C.S. incluyendo una cogeneración con pila de combustible. Al mismo tiempo se han calculado y diseñado una serie de chimeneas externas para dar cumplida necesidad técnica y legal al proyecto. Estos estudios nos sirven de punto de partida para analizar la amortización de la inversión y por tanto la rentabilidad y viabilidad del proyecto, comparándose con los costes económicos derivados de la generación por sistemas convencionales. Para finalizar se hace mención a las ventajas medioambientales y a los grados de seguridad en la planta de producción ABSTRACT The scope of this work is the description of an energy supply project ( Electricity, heat and hot water ) to a housing development in a urban neibourhood , including technical criteria in their different options. Initially, several solutions are studied based on available technologies and legal restrictions. The final proposal is based on the district hearing model including electricity production in cogeneration via fuel cell technology as well as heating and hot water produced by low temperature condensation boilers It includes calculations and design criteria of the exhaust gases system and chimeneys in compliance with legal requirement in urban areas. This work also includes an economical model including payback, IRR and VAN analysis and an economical comparaison with the standard solutions. Finally, environmental advantages of the preferred solution over other standards as well as safety issues are also presented.

Modelo para la certificación del coordinador en materia de seguridad y salud basado en sus competencias

La figura del coordinador en materia de seguridad y salud en el sector de la construcción, aparecida en nuestra legislación a través de las trasposiciones de las Directivas Europeas, (en nuestro caso en el RD 1627/97 sobre disposiciones mínimas de seguridad y salud en las obras de construcción), se encuentra identificada, en cuanto a su posible contratación y actuación dentro de este sector, de forma diferente en distintos países de la Unión Europea. La coordinación en materia de seguridad y salud también es un proceso de gestión que requiere de unas competencias, no solamente basadas en la formación técnica o profesional, si no que, considerando el entorno de trabajo, precisan de la aplicación de estrategias y herramientas relacionadas con la experiencia y con las habilidades personales. A través de una primera fase de investigación realizada y considerando la opinión de expertos en la materia, se han detectado cuáles son estas competencias que debe poseer el coordinador en materia de seguridad y salud para fortalecer el cumplimiento de sus obligaciones y así, mejorar su actividad de coordinación. El resultado de los análisis realizados permitirá construir un modelo que sirva de referencia para la certificación de los coordinadores en materia de seguridad y salud basado en sus competencias. Las conclusiones recogidas en esta Tesis doctoral proporcionarán criterios para establecer el diseño de programas formativos y construir metodologías para la selección de los coordinadores en materia de seguridad y salud en base a sus competencias. ABSTRACT The figure of the health and safety coordinator in the construction sector appeared in our legislation through the incorporation of the European Directives. In our case, Royal Decree 1627/97 on the minimum health and safety regulations in construction works. This figure is viewed differently, in terms of recruitment and performance, in different countries of the European Union. The coordination of health and safety issues is a management process that requires certain competencies not only based on technical or professional training. It is also necessary, depending on the work environment, the implementation of strategies and tools that are related to experience and personal skills. The skill requirements for the health and safety coordinator have been defined considering the opinion of experts in this field, gained through the realization of a first phase of research. These competences should be used to strengthen the performance of their duties and thereby improve their coordination activity.

The structure of lean hydrogen-air flame balls

An analysis of the structure of flame balls encountered under microgravity conditions, which are stable due to radiant energy losses from H₂O, is carried out for fuel-lean hydrogen-air mixtures. It is seen that, because of radiation losses, in stable flame balls the maximum flame temperature remains close to the crossover temperature, at which the rate of the branching step H + O₂ -> OH + O equals that of the recombination step H + O₂ + M -> HO₂ + M. Under those conditions, all chemical intermediates have very small concentrations and follow the steady-state approximation, while the main species react according to the overall step 2H₂ + O₂-> 2H₂O; so that a one-step chemical-kinetic description, recently derived by asymptotic analysis for near-limit fuel-lean deflagrations, can be used with excellent accuracy to describe the whole branch of stable flame balls. Besides molecular diffusion in a binary-diffusion approximation, Soret diffusion is included, since this exerts a nonnegligible effect to extend the flammability range. When the large value of the activation energy of the overall reaction is taken into account, the leading-order analysis in the reaction-sheet approximation is seen to determine the flame ball radius as that required for radiant heat losses to remove enough of the heat released by chemical reaction at the flame to keep the flame temperature at a value close to crossover. The results are relevant to burning velocities at lean equivalent ratios and may influence fire-safety issues associated with hydrogen utilization.

Code assessment and modelling for Design Basis Accident Analysis of the European sodium fast reactor design. Part I: System description, modelling and benchmarking

The new reactor concepts proposed in the Generation IV International Forum (GIF) are conceived to improve the use of natural resources, reduce the amount of high-level radioactive waste and excel in their reliability and safe operation. Among these novel designs sodium fast reactors (SFRs) stand out due to their technological feasibility as demonstrated in several countries during the last decades. As part of the contribution of EURATOM to GIF the CP-ESFR is a collaborative project with the objective, among others, to perform extensive analysis on safety issues involving renewed SFR demonstrator designs. The verification of computational tools able to simulate the plant behaviour under postulated accidental conditions by code-to-code comparison was identified as a key point to ensure reactor safety. In this line, several organizations employed coupled neutronic and thermal-hydraulic system codes able to simulate complex and specific phenomena involving multi-physics studies adapted to this particular fast reactor technology. In the “Introduction” of this paper the framework of this study is discussed, the second section describes the envisaged plant design and the commonly agreed upon modelling guidelines. The third section presents a comparative analysis of the calculations performed by each organisation applying their models and codes to a common agreed transient with the objective to harmonize the models as well as validating the implementation of all relevant physical phenomena in the different system codes.

Islanding detection in Microgrids using Harmonic Signature

In recent years, there has been a growing interest in incorporating microgrids in electrical power networks. This is due to various advantages they present, particularly the possibility of working in either autonomous mode or grid connected, which makes them highly versatile structures for incorporating intermittent generation and energy storage. However, they pose safety issues in being able to support a local island in case of utility disconnection. Thus, in the event of an unintentional island situation, they should be able to detect the loss of mains and disconnect for self-protection and safety reasons. Most of the anti-islanding schemes are implemented within control of single generation devices, such as dc-ac inverters used with solar electric systems being incompatible with the concept of microgrids due to the variety and multiplicity of sources within the microgrid. In this paper, a passive islanding detection method based on the change of the 5th harmonic voltage magnitude at the point of common coupling between grid-connected and islanded modes of operation is presented. Hardware test results from the application of this approach to a laboratory scale microgrid are shown. The experimental results demonstrate the validity of the proposed method, in meeting the requirements of IEEE 1547 standards.

GPS-PYMEs: Marco de Gestión de Proyectos para el desarrollo Seguro en PYMEs

En la actualidad no se concibe una empresa, por pequeña que esta sea, sin algún tipo de servicio TI. Se presenta para cada empresa el reto de emprender proyectos para desarrollar o contratar servicios de TI que soporten los diferentes procesos de negocio de la empresa. Por otro lado, a menos que los servicios de TI estén aislados de toda red, lo cual es prácticamente imposible en la actualidad, no existe un servicio o un proyecto que lo desarrolle garantizando el 100% de seguridad. Así la empresa maneja una dualidad entre desarrollar productos/servicios de TI seguros y el mantenimiento constante de sus servicios TI en estado seguro. La gestión de los proyectos para el desarrollo de los servicios de TI se aborda, en la mayoría de las empresas, aplicando distintas prácticas, utilizadas en otros proyectos y recomendadas, a tal efecto, por marcos y estándares con mayor reconocimiento. Por lo general, estos marcos incluyen, entre sus procesos, la gestión de los riesgos orientada al cumplimiento de plazos, de costes y, a veces, de la funcionalidad del producto o servicio. Sin embargo, en estas prácticas se obvian los aspectos de seguridad (confidencialidad, integridad y disponibilidad) del producto/servicio, necesarios durante el desarrollo del proyecto. Además, una vez entregado el servicio, a nivel operativo, cuando surge algún fallo relativo a estos aspectos de seguridad, se aplican soluciones ad-hoc. Esto provoca grandes pérdidas y, en ocasiones, pone en peligro la continuidad de la propia empresa. Este problema, se va acrecentando cada día más, en cualquier tipo de empresa y, son las PYMEs, por su la falta de conocimiento del problema en sí y la escasez de recursos metodológicos y técnicos, las empresas más vulnerables. Por todo lo anterior, esta tesis doctoral tiene un doble objetivo. En primer lugar, demostrar la necesidad de contar con un marco de trabajo que, integrado con otros posibles marcos y estándares, sea sencillo de aplicar en distintos tipos y envergaduras de proyectos, y que guíe a las PYMEs en la gestión de proyectos para el desarrollo seguro y posterior mantenimiento de la seguridad de sus servicios de TI. En segundo lugar, cubrir esta necesidad desarrollando un marco de trabajo que ofrezca un modelo de proceso genérico aplicable sobre distintos patrones de proyecto y una librería de activos de seguridad que sirva a las PYMEs de guía durante el proceso de gestión del proyecto para el desarrollo seguro. El modelo de proceso del marco propuesto describe actividades en los tres niveles organizativos de la empresa (estratégico, táctico y operativo). Está basado en el ciclo de mejora continua (PDCA) y en la filosofía Seguridad por Diseño, propuesta por Siemens. Se detallan las prácticas específicas de cada actividad, las entradas, salidas, acciones, roles, KPIs y técnicas aplicables para cada actividad. Estas prácticas específicas pueden aplicarse o no, a criterio del jefe de proyecto y de acuerdo al estado de la empresa y proyecto que se quiera desarrollar, estableciendo así distintos patrones de proceso. Para la validación del marco se han elegido dos PYMEs. La primera del sector servicios y la segunda del sector TIC. El modelo de proceso ha sido aplicado sobre un mismo patrón de proyecto que responde a necesidades comunes a ambas empresas. El patrón de proceso ha sido valorado en los proyectos elegidos en ambas empresas, antes y después de su aplicación. Los resultados del estudio, después de su aplicación en ambas empresas, han permitido la validación del patrón de proceso, en la mejora de la gestión de proyecto para el desarrollo seguro de TI en las PYMEs. ABSTRACT Today a company without any IT service is not conceived, even if it is small either. It presents the challenge for each company to undertake projects to develop or contract IT services that support the different business processes of the company. On the other hand, unless IT services are isolated from whole network, which is virtually impossible at present, there is no service or project, which develops guaranteeing 100% security. So the company handles a duality, develop products / insurance IT services and constant maintenance of their IT services in a safe state. The project management for the development of IT services is addressed, in most companies, using different practices used in other projects and recommended for this purpose by frameworks and standards with greater recognition. Generally, these frameworks include, among its processes, risk management aimed at meeting deadlines, costs and, sometimes, the functionality of the product or service. However, safety issues such as confidentiality, integrity and availability of the product / service, necessary for the project, they are ignored in these practices. Moreover, once the service delivered at the operational level, when a fault on these safety issues arise, ad-hoc solutions are applied. This causes great losses and sometimes threatens the continuity of the company. This problem is adding more every day, in any kind of business and SMEs are, by their lack of knowledge of the problem itself and the lack of methodological and technical resources, the most vulnerable companies. For all these reasons, this thesis has two objectives. Firstly demonstrate the need for a framework that integrated with other possible frameworks and standards, it is simple to apply in different types and wingspans of projects, and to guide SMEs in the management of development projects safely, and subsequent maintenance of the security of their IT services. Secondly meet this need by developing a framework that provides a generic process model applicable to project different patterns and a library of security assets, which serve to guide SMEs in the process of project management for development safe. The process model describes the proposed activities under the three organizational levels of the company (strategic, tactical and operational). It is based on the continuous improvement cycle (PDCA) and Security Design philosophy proposed by Siemens. The specific practices, inputs, outputs, actions, roles, KPIs and techniques applicable to each activity are detailed. These specific practices can be applied or not, at the discretion of the project manager and according to the state of the company and project that the company wants to develop, establishing different patterns of process. Two SMEs have been chosen to validate the frame work. The first of the services sector and the second in the ICT sector. The process model has been applied on the same pattern project that responds to needs common to both companies. The process pattern has been valued at the selected projects in both companies before and after application. The results of the study, after application in both companies have enabled pattern validation process, improving project management for the safe development of IT in SMEs.

Multiphase Design and Control Techniques Applied to a Forward Micro-Inverter

En la última década la potencia instalada de energía solar fotovoltaica ha crecido una media de un 49% anual y se espera que alcance el 16%del consumo energético mundial en el año 2050. La mayor parte de estas instalaciones se corresponden con sistemas conectados a la red eléctrica y un amplio porcentaje de ellas son instalaciones domésticas o en edificios. En el mercado ya existen diferentes arquitecturas para este tipo de instalaciones, entre las que se encuentras los módulos AC. Un módulo AC consiste en un inversor, también conocido como micro-inversor, que se monta en la parte trasera de un panel o módulo fotovoltaico. Esta tecnología ofrece modularidad, redundancia y la extracción de la máxima potencia de cada panel solar de la instalación. Además, la expansión de esta tecnología posibilitará una reducción de costes asociados a las economías de escala y a la posibilidad de que el propio usuario pueda componer su propio sistema. Sin embargo, el micro-inversor debe ser capaz de proporcionar una ganancia de tensión adecuada para conectar el panel solar directamente a la red, mientras mantiene un rendimiento aceptable en un amplio rango de potencias. Asimismo, los estándares de conexión a red deber ser satisfechos y el tamaño y el tiempo de vida del micro-inversor son factores que han de tenerse siempre en cuenta. En esta tesis se propone un micro-inversor derivado de la topología “forward” controlado en el límite entre los modos de conducción continuo y discontinuo (BCM por sus siglas en inglés). El transformador de la topología propuesta mantiene la misma estructura que en el convertidor “forward” clásico y la utilización de interruptores bidireccionales en el secundario permite la conexión directa del inversor a la red. Asimismo el método de control elegido permite obtener factor de potencia cercano a la unidad con una implementación sencilla. En la tesis se presenta el principio de funcionamiento y los principales aspectos del diseño del micro-inversor propuesto. Con la idea de mantener una solución sencilla y de bajo coste, se ha seleccionado un controlador analógico que está originalmente pensado para controlar un corrector del factor de potencia en el mismo modo de conducción que el micro-inversor “forward”. La tesis presenta las principales modificaciones necesarias, con especial atención a la detección del cruce por cero de la corriente (ZCD por sus siglas en inglés) y la compatibilidad del controlador con la inclusión de un algoritmo de búsqueda del punto de máxima potencia (MPPT por sus siglas en inglés). Los resultados experimentales muestran las limitaciones de la implementación elegida e identifican al transformador como el principal contribuyente a las pérdidas del micro-inversor. El principal objetivo de esta tesis es contribuir a la aplicación de técnicas de control y diseño de sistemas multifase en micro-inversores fotovoltaicos. En esta tesis se van a considerar dos configuraciones multifase diferentes aplicadas al micro-inversor “forward” propuesto. La primera consiste en una variación con conexión paralelo-serie que permite la utilización de transformadores con una relación de vueltas baja, y por tanto bien acoplados, para conseguir una ganancia de tensión adecuada con un mejor rendimiento. Esta configuración emplea el mismo control BCM cuando la potencia extraída del panel solar es máxima. Este método de control implica que la frecuencia de conmutación se incrementa considerablemente cuando la potencia decrece, lo que compromete el rendimiento. Por lo tanto y con la intención de mantener unos bueno niveles de rendimiento ponderado, el micro-inversor funciona en modo de conducción discontinuo (DCM, por sus siglas en inglés) cuando la potencia extraía del panel solar es menor que la máxima. La segunda configuración multifase considerada en esta tesis es la aplicación de la técnica de paralelo con entrelazado. Además se han considerado dos técnicas diferentes para decidir el número de fases activas: dependiendo de la potencia continua extraída del panel solar y dependiendo de la potencia instantánea demandada por el micro-inversor. La aplicación de estas técnicas es interesante en los sistemas fotovoltaicos conectados a la red eléctrica por la posibilidad que brindan de obtener un rendimiento prácticamente plano en un amplio rango de potencia. Las configuraciones con entrelazado se controlan en DCM para evitar la necesidad de un control de corriente, lo que es importante cuando el número de fases es alto. Los núcleos adecuados para todas las configuraciones multifase consideradas se seleccionan usando el producto de áreas. Una vez seleccionados los núcleos se ha realizado un diseño detallado de cada uno de los transformadores. Con la información obtenida de los diseños y los resultados de simulación, se puede analizar el impacto que el número de transformadores utilizados tiene en el tamaño y el rendimiento de las distintas configuraciones. Los resultados de este análisis, presentado en esta tesis, se utilizan posteriormente para comparar las distintas configuraciones. Muchas otras topologías se han presentado en la literatura para abordar los diferentes aspectos a considerar en los micro-inversores, que han sido presentados anteriormente. La mayoría de estas topologías utilizan un transformador de alta frecuencia para solventar el salto de tensión y evitar problemas de seguridad y de puesta a tierra. En cualquier caso, es interesante evaluar si topologías sin aislamiento galvánico son aptas para su utilización como micro-inversores. En esta tesis se presenta una revisión de inversores con capacidad de elevar tensión, que se comparan bajo las mismas especificaciones. El objetivo es proporcionar la información necesaria para valorar si estas topologías son aplicables en los módulos AC. Las principales contribuciones de esta tesis son: • La aplicación del control BCM a un convertidor “forward” para obtener un micro-inversor de una etapa sencillo y de bajo coste. • La modificación de dicho micro-inversor con conexión paralelo-series de transformadores que permite reducir la corriente de los semiconductores y una ganancia de tensión adecuada con transformadores altamente acoplados. • La aplicación de técnicas de entrelazado y decisión de apagado de fases en la puesta en paralelo del micro-inversor “forward”. • El análisis y la comparación del efecto en el tamaño y el rendimiento del incremento del número de transformadores en las diferentes configuraciones multifase. • La eliminación de las medidas y los lazos de control de corriente en las topologías multifase con la utilización del modo de conducción discontinuo y un algoritmo MPPT sin necesidad de medida de corriente. • La recopilación y comparación bajo las mismas especificaciones de topologías inversoras con capacidad de elevar tensión, que pueden ser adecuadas para la utilización como micro-inversores. Esta tesis está estructurada en seis capítulos. El capítulo 1 presenta el marco en que se desarrolla la tesis así como el alcance de la misma. En el capítulo 2 se recopilan las topologías existentes de micro-invesores con aislamiento y aquellas sin aislamiento cuya implementación en un módulo AC es factible. Asimismo se presenta la comparación entre estas topologías bajo las mismas especificaciones. El capítulo 3 se centra en el micro-inversor “forward” que se propone originalmente en esta tesis. La aplicación de las técnicas multifase se aborda en los capítulos 4 y 5, en los que se presentan los análisis en función del número de transformadores. El capítulo está orientado a la propuesta paralelo-serie mientras que la configuración con entrelazado se analiza en el capítulo 5. Por último, en el capítulo 6 se presentan las contribuciones de esta tesis y los trabajos futuros. ABSTRACT In the last decade the photovoltaic (PV) installed power increased with an average growth of 49% per year and it is expected to cover the 16% of the global electricity consumption by 2050. Most of the installed PV power corresponds to grid-connected systems, with a significant percentage of residential installations. In these PV systems, the inverter is essential since it is the responsible of transferring into the grid the extracted power from the PV modules. Several architectures have been proposed for grid-connected residential PV systems, including the AC-module technology. An AC-module consists of an inverter, also known as micro-inverter, which is attached to a PV module. The AC-module technology offers modularity, redundancy and individual MPPT of each module. In addition, the expansion of this technology will enable the possibility of economies of scale of mass market and “plug and play” for the user, thus reducing the overall cost of the installation. However, the micro-inverter must be able to provide the required voltage boost to interface a low voltage PV module to the grid while keeping an acceptable efficiency in a wide power range. Furthermore, the quality standards must be satisfied and size and lifetime of the solutions must be always considered. In this thesis a single-stage forward micro-inverter with boundary mode operation is proposed to address the micro-inverter requirements. The transformer in the proposed topology remains as in the classic forward converter and bidirectional switches in the secondary side allows direct connection to the grid. In addition the selected control strategy allows high power factor current with a simple implementation. The operation of the topology is presented and the main design issues are introduced. With the intention to propose a simple and low-cost solution, an analog controller for a PFC operated in boundary mode is utilized. The main necessary modifications are discussed, with the focus on the zero current detection (ZCD) and the compatibility of the controller with a MPPT algorithm. The experimental results show the limitations of the selected analog controller implementation and the transformer is identified as a main losses contributor. The main objective of this thesis is to contribute in the application of control and design multiphase techniques to the PV micro-inverters. Two different multiphase configurations have been applied to the forward micro-inverter proposed in this thesis. The first one consists of a parallel-series connected variation which enables the use of low turns ratio, i.e. well coupled, transformers to achieve a proper voltage boost with an improved performance. This multiphase configuration implements BCM control at maximum load however. With this control method the switching frequency increases significantly for light load operation, thus jeopardizing the efficiency. Therefore, in order to keep acceptable weighted efficiency levels, DCM operation is selected for low power conditions. The second multiphase variation considered in this thesis is the interleaved configuration with two different phase shedding techniques: depending on the DC power extracted from the PV panel, and depending on the demanded instantaneous power. The application of interleaving techniques is interesting in PV grid-connected inverters for the possibility of flat efficiency behavior in a wide power range. The interleaved variations of the proposed forward micro-inverter are operated in DCM to avoid the current loop, which is important when the number of phases is large. The adequate transformer cores for all the multiphase configurations are selected according to the area product parameter and a detailed design of each required transformer is developed. With this information and simulation results, the impact in size and efficiency of the number of transformer used can be assessed. The considered multiphase topologies are compared in this thesis according to the results of the introduced analysis. Several other topological solutions have been proposed to solve the mentioned concerns in AC-module application. The most of these solutions use a high frequency transformer to boost the voltage and avoid grounding and safety issues. However, it is of interest to assess if the non-isolated topologies are suitable for AC-module application. In this thesis a review of transformerless step-up inverters is presented. The compiled topologies are compared using a set benchmark to provide the necessary information to assess whether non-isolated topologies are suitable for AC-module application. The main contributions of this thesis are: • The application of the boundary mode control with constant off-time to a forward converter, to obtain a simple and low-cost single-stage forward micro-inverter. • A modification of the forward micro-inverter with primary-parallel secondary-series connected transformers to reduce the current stress and improve the voltage gain with highly coupled transformers. •The application of the interleaved configuration with different phase shedding strategies to the proposed forward micro-inverter. • An analysis and comparison of the influence in size and efficiency of increasing the number of transformers in the parallel-series and interleaved multiphase configurations. • Elimination of the current loop and current measurements in the multiphase topologies by adopting DCM operation and a current sensorless MPPT. • A compilation and comparison with the same specifications of suitable non-isolated step-up inverters. This thesis is organized in six chapters. In Chapter 1 the background of single-phase PV-connected systems is discussed and the scope of the thesis is defined. Chapter 2 compiles the existing solutions for isolated micro-inverters and transformerless step-up inverters suitable for AC-module application. In addition, the most convenient non-isolated inverters are compared using a defined benchmark. Chapter 3 focuses on the originally proposed single-stage forward micro-inverter. The application of multiphase techniques is addressed in Chapter 4 and Chapter 5, and the impact in different parameters of increasing the number of phases is analyzed. In Chapter 4 an original primary-parallel secondary-series variation of the forward micro-inverter is presented, while Chapter 5 focuses on the application of the interleaved configuration. Finally, Chapter 6 discusses the contributions of the thesis and the future work.

Aircraft accident report : collision with trees and crash short of the runway, Corporate Airlines flight 5966, BAE systems BAE-J3201, N875JX, Kirksville, Missouri, October 19, 2004 /

On October 19, 2004, about 1937 central daylight time, Corporate Airlines (doing business as American Connection) flight 5966, a BAE Systems BAE-J3201, N875JX, struck trees on final approach and crashed short of runway 36 at the Kirksville Regional Airport (IRK), Kirksville, Missouri. The flight was operating under the provisions of 14 Code of Federal Regulations Part 121 as a scheduled passenger flight from Lambert-St. Louis International Airport, in St. Louis, Missouri, to IRK. The captain, first officer, and 11 of the 13 passengers were fatally injured, and 2 passengers received serious injuries. The airplane was destroyed by impact and a post impact fire. Night instrument meteorological conditions (IMC) prevailed at the time of the accident, and the flight operated on an instrument flight rules flight plan. The National Transportation Safety Board determines that the probable cause of the accident was the pilots' failure to follow established procedures and properly conduct a nonprecision instrument approach at night in IMC, including their descent below the minimum descent altitude (MDA) before required visual cues were available (which continued unmoderated until the airplane struck the trees) and their failure to adhere to the established division of duties between the flying and nonflying (monitoring) pilot. Contributing to the accident was the pilots' failure to make standard callouts and the current Federal Aviation Regulations that allow pilots to descend below the MDA into a region in which safe obstacle clearance is not assured based upon seeing only the airport approach lights. The pilots' unprofessional behavior during the flight and their fatigue likely contributed to their degraded performance. The safety issues in this report focus on operational and human factors issues, including the pilots' professionalism and sterile cockpit procedures, nonprecision instrument approach procedures, flight and duty time regulations, fatigue, and flight data/image recorder requirements.

Viscosupplementation for the treatment of osteoarthritis of the knee (Review)

Background Osteoarthritis (OA) is the most prevalent chronic joint disorder worldwide and is associated with significant pain and disability. Objectives To assess the effects of viscosupplementation in the treatment of OA of the knee. The products were hyaluronan and hylan derivatives (Adant, Arthrum H, Artz (Artzal, Supartz), BioHy (Arthrease, Euflexxa, Nuflexxa), Durolane, Fermathron, Go-On, Hyalgan, Hylan G-F 20 (Synvisc Hylan G-F 20), Hyruan, NRD-101 (Suvenyl), Orthovisc, Ostenil, Replasyn, SLM-10, Suplasyn, Synject and Zeel compositum). Search strategy MEDLINE (up to January (week 1) 2006 for update), EMBASE, PREMEDLINE, Current Contents up to July 2003, and the Cochrane Central Register of Controlled Trials (CENTRAL) were searched. Specialised journals and reference lists of identified randomised controlled trials (RCTs) and pertinent review articles up to December 2005 were handsearched. Selection criteria RCTs of viscosupplementation for the treatment of people with a diagnosis of OA of the knee were eligible. Single and double-blinded studies, placebo-based and comparative studies were eligible. At least one of the four OMERACT III core set outcome measures had to be reported (Bellamy 1997). Data collection and analysis Each trial was assessed independently by two reviewers for its methodological quality using a validated tool. All data were extracted by one reviewer and verified by a second reviewer. Continuous outcome measures were analysed as weighted mean differences (WMD) with 95% confidence intervals (CI). However, where different scales were used to measure the same outcome, standardized mean differences (SMD) were used. Dichotomous outcomes were analyzed by relative risk (RR). Main results Seventy-six trials with a median quality score of 3 (range 1 to 5) were identified. Follow-up periods varied between day of last injection and eighteen months. Forty trials included comparisons of hyaluronan/hylan and placebo (saline or arthrocentesis), ten trials included comparisons of intra-articular (IA) corticosteroids, six trials included comparisons of nonsteroidal anti-inflammatory drugs (NSAIDs), three trials included comparisons of physical therapy, two trials included comparisons of exercise, two trials included comparisons of arthroscopy, two trials included comparisons of conventional treatment, and fifteen trials included comparisons of other hyaluronans/hylan. The pooled analyses of the effects of viscosupplements against 'placebo' controls generally supported the efficacy of this class of intervention. In these same analyses, differential efficacy effects were observed for different products on different variables and at different timepoints. Of note is the 5 to 13 week post injection period which showed a percent improvement from baseline of 28 to 54% for pain and 9 to 32% for function. In general, comparable efficacy was noted against NSAIDs and longer-term benefits were noted in comparisons against IA corticosteroids. In general, few adverse events were reported in the hyaluronan/hylan trials included in these analyses. Authors' conclusions Based on the aforementioned analyses, viscosupplementation is an effective treatment for OA of the knee with beneficial effects: on pain, function and patient global assessment; and at different post injection periods but especially at the 5 to 13 week post injection period. It is of note that the magnitude of the clinical effect, as expressed by the WMD and standardised mean difference (SMD) from the RevMan 4.2 output, is different for different products, comparisons, timepoints, variables and trial designs. However, there are few randomised head-to-head comparisons of different viscosupplements and readers should be cautious, therefore, in drawing conclusions regarding the relative value of different products. The clinical effect for some products, against placebo, on some variables at some timepoints is in the moderate to large effect-size range. Readers should refer to relevant tables to review specific detail given the heterogeneity in effects across the product class and some discrepancies observed between the RevMan 4.2 analyses and the original publications. Overall, the analyses performed are positive for the HA class and particularly positive for some products with respect to certain variables and timepoints, such as pain on weight bearing at 5 to 13 weeks postinjection. In general, sample-size restrictions preclude any definitive comment on the safety of the HA class of products; however, within the constraints of the trial designs employed no major safety issues were detected. In some analyses viscosupplements were comparable in efficacy to systemic forms of active intervention, with more local reactions but fewer systemic adverse events. In other analyses HA products had more prolonged effects than IA corticosteroids. Overall, the aforementioned analyses support the use of the HA class of products in the treatment of knee OA.

Numerical modeling of 11.1 T MRI of a human head using MoM/FDTD methods

In a recent study, severe distortions in the proton images of an excised, fixed, human brain in an 11.1 Tesla/40 cm MR instrument have been observed, and the effect modeled on phantom images using a finite difference time domain (FDTD) model. in the present study, we extend these simulations to that of a complete human head, employing a hybrid FDTD and method of moments (MoM) approach, which provides a validated method for simulating biological samples in coil structures. The effect of fixative on the image distortions is explored. importantly, temperature distributions within the head are also simulated using a bioheat method based on parameters derived from the electromagnetic simulations. The MoM/FDTD simulations confirm that the transverse magnetic field (B,) from a ReCav resonator exhibits good homogeneity in air but strong inhomogeneity when loaded with the head with or without fixative. The fixative serves to increase the distortions, but they are still significant for the in vivo simulations. The simulated signal intensity (SI) distribution within the sample confirm the distortions in the experimental images are caused by the complex interactions of the incident electromagnetic fields with tissue, which is heterogeneous in terms of conductivity and permittivity. The temperature distribution is likewise heterogeneous, raising concerns regarding hot spot generation in the sample that may exceed acceptable levels in future in vivo studies. As human imaging at 11.1 T is some time away, simulations are important in terms of predicting potential safety issues as well as evaluating practical concerns about the quality of images. Simulation on a whole human head at 11.1 T implies the wave behavior presents significant engineering challenges for ultra-high-field (UHF) MRI. Novel strategies will have to be employed in imaging technique and resonator design for UHF MRI to achieve the theoretical signal-to-noise ratio (SNR) improvements it offers over lower field systems. (C) 2005 Wiley Periodicals, Inc.

Type 2 diabetes:assessing the relative risks and benefits of glucose-lowering medications

The selection of appropriate pharmacologic therapy for any disease requires a careful assessment of benefit and risk. In the case of type 2 diabetes, this decision typically balances the benefits accrued from improved glycemic control with the risks inherent in glucose-lowering medications. This review is intended to assist therapeutic decision-making by carefully assessing the potential benefit from improved metabolic control relative to the potential risks of a wide array of currently prescribed glucose-lowering agents. Wherever possible, risks and benefits have been expressed in terms of absolute rates (events per 1000 patient-years) to facilitate cross-study comparisons. The review incorporates data from new studies (Action in Diabetes and Vascular Disease: Preterax and Diamicron Modified Release Controlled Evaluation, Action to Control Cardiovascular Risk in Diabetes, and the Veterans Affairs Diabetes Trial), as well as safety issues associated with newer glucose-lowering medications. © 2010 Elsevier Inc. All rights reserved.

Formulation and characterisation of cationic microparticles for the delivery of DNA vaccines

The aim of this research was to formulate a novel biodegradable, biocompatible cationic microparticle vector for the delivery of DNA vaccines. The work builds upon previous research by Singh et al which described the adsorption of DNA to the surface of poly (D,L-lactide-co-glycolide) (PLG) microparticles stabilised with the surfactant cetyltrimethyl ammonium bromide (CT AB). This work demonstrated the induction of antibody and cellular immune responses to HIV proteins encoded on plasmid DNA adsorbed to the particle surface in mice, guinea pigs and non-human primates (Singh et aI, 2000; O'Hagan et aI, 2001). However, the use of surfactants in microparticle formulations for human vaccination is undesirable due to long term safety issues. Therefore, the present research aim was to develop an adsorbed DNA vaccine with enhanced potency and increased safety compared to CTAB stabilised PLG microparticles (PLG/CTAB) by replacement of the surfactant CTAB with an alternative cationic agent. The cationic polymers chitosan and poly (N- vinylpyrrolidone/2-dimethylaminoethyl methacrylate), dimethyl sulfate quaternary (PVP-PDAEMA) were investigated as alternative stabilisers to CTAB. From a variety of initial formulations, the most promising vector(s) for DNA vaccination were selected based on physicochemical data (chapter 3) and in vitro DNA loading and release characteristics (chapter 4). The chosen formulation(s) were analysed in greater depth (chapters 3 and 4), and gene expression was assessed by in vitro cell transfection studies using 293T kidney epithelial and C2C12 myoblast non-phagocytic cell lines (chapter 5). The cytotoxicity of the microparticles and their constituents were also evaluated in vitro (chapter 5). Stability and suitability of the formulation(s) for commercial production were assessed by cryopreparation and lyophilisation studies (chapters 3 and 4). Gene expression levels in cells of the immune response were evaluated by microparticle transfection of the dendritic cell (DC) line 2.4 and primary bone marrow derived DCs (chapter 6). In vivo, mice were injected i.m. with the formulations deemed most promising on the basis of in vitro studies and humoral and cellular immune responses were evaluated (chapter 6).

Editorial : which weight loss diet?

Full editorial: A recent study evaluating the long-term (2 yr) weight reducing efficacy of different types of diets – high or low in carbohydrates (CHOs), protein or fat - confirmed that it is calorie deficit not dietary composition that determines the loss and maintenance of body weight.1 Is there any advantage in following a specific weight loss diet? Short-term use of nutritionally complete commercially available (very) low calorie diets has benefited people with diabetes when  supported by education programmes.2 Initial weight loss has been encouraging with some fad diets eg the Atkins and the South Beach diets, but these diets are difficult to maintain and there are safety issues regarding their short- and long-term use – especially in people with diabetes.3 The types of macronutrients consumed can have a considerable impact on glycaemic control and energy metabolism. Although a low CHO diet additionally enhances initial weight loss by reducing cellular water content, if fat is not proportionally reduced the diet may not benefit the lipid profile for vascular disease risk. High fat and high protein diets – which are simultaneously low in CHOs – increase vulnerability to hypoglycaemia in people taking insulin secretagogues or on insulin therapy, and may promote excess fat metabolism and ketogenesis, particularly in people vulnerable to lack of insulin. Very low protein diets are not recommended as lean body mass tends to be reduced in diabetes. Altering the macronutrient balance has implications for the micronutrient mix: deficiencies are higher if more foods are excluded and conversely specific micronutrient excess can occur with some fad diets. The altered nutrient mix affects intestinal fauna and flora, and gut motility and glycaemic control are influenced by the quantity and type of fibre consumed. Support programmes help individuals achieve long term weight loss and there is mounting evidence that community schemes which educate and promote lifestyle changes may stem the rising tide of obesity and consequent type 2 diabetes.4 Consuming smaller portions of a balanced diet (and adjusting antidiabetic medications accordingly) will create an energy deficit to promote healthy weight loss. Increased movement/exercise will enhance this energy deficit. Knowledge (eg 1g fat has 2.25 times more energy than 1g CHO) allows sensible food choices and compensation for inclusion of small volumes of  ‘naughty but nice’ foods. Ultimately weight control requires self control. References 1. Sacks FM, Bray GA, Carey VJ et al. Comparison of weight-loss diets with different compositions of fat, protein, and carbohydrates. N Engl J Med 2009;360:859–73. 2. Bennett P. Obesity, diabetes and VLCD. Br J Diabetes Vasc Dis 2004;4:328–30. 3. Baldwin EJ. Fad diets in diabetes. Br J Diabetes Vasc DIs 2004;4:333–7. 4. Romon M, Lommoz A, Tafflet M et al. Downward trends in the prevalence of childhood overweight in the setting of 12-year school- and community-based programmes. Public Health Nutr 2008; Dec 28, 1–8 [Epub ahead of print].

Developing accurate models of the human airways

Objectives Particle delivery to the airways is an attractive prospect for many potential therapeutics, including vaccines. Developing strategies for inhalation of particles provides a targeted, controlled and non-invasive delivery route but, as with all novel therapeutics, in vitro and in vivo testing are needed prior to clinical use. Whilst advanced vaccine testing demands the use of animal models to address safety issues, the production of robust in vitro cellular models would take account of the ethical framework known as the 3Rs (Replacement, Reduction and Refinement of animal use), by permitting initial screening of potential candidates prior to animal use. There is thus a need for relevant, realistic in vitro models of the human airways. Key findings Our laboratory has designed and characterised a multi-cellular model of human airways that takes account of the conditions in the airways and recapitulates many salient features, including the epithelial barrier and mucus secretion. Summary Our human pulmonary models recreate many of the obstacles to successful pulmonary delivery of particles and therefore represent a valid test platform for screening compounds and delivery systems.

A probabilistic approach to assess hydrate formation and design preventive measures

Formation of hydrates is one of the major flow assurance problems faced by the oil and gas industry. Hydrates tend to form in natural gas pipelines with the presence of water and favorable temperature and pressure conditions, generally low temperatures and corresponding high pressures. Agglomeration of hydrates can result in blockage of flowlines and equipment, which can be time consuming to remove in subsea equipment and cause safety issues. Natural gas pipelines are more susceptible to burst and explosion owing to hydrate plugging. Therefore, a rigorous risk-assessment related to hydrate formation is required, which assists in preventing hydrate blockage and ensuring equipment integrity. This thesis presents a novel methodology to assess the probability of hydrate formation and presents a risk-based approach to determine the parameters of winterization schemes to avoid hydrate formation in natural gas pipelines operating in Arctic conditions. It also presents a lab-scale multiphase flow loop to study the effects of geometric and hydrodynamic parameters on hydrate formation and discusses the effects of geometric and hydrodynamic parameters on multiphase development length of a pipeline. Therefore, this study substantially contributes to the assessment of probability of hydrate formation and the decision making process of winterization strategies to prevent hydrate formation in Arctic conditions.