Plant availability of phosphorus in four superphosphate fertilizers varying in water-insoluble phosphate compounds

There is concern that the use of lower quality phosphate rock can result in elevated amounts of Fe-Al-P water-insoluble compounds in fertilizers and, consequently, low agronomic effectiveness. Therefore, studies were conducted to evaluate the effect of some of these compounds on plant growth. Four commercial superphosphates varying in chemical composition (two single and two triple superphosphates) were selected for the study. Fertilizer impurities were collected as water-insoluble residues by washing each P source with deionized water. A modal analysis, based primarily on elemental chemical analysis and x-ray diffractometry, was used to estimate the chemical composition of each P source. Water-soluble monocalcium phosphate (MCP) and the water-leached fertilizer residues were prepared to give a range of fertilizers in terms of water-soluble phosphorus (WSP) (0-100% of the available P as MCP). The water-leached fractions, MCP, and the mixtures of MCP with water-leached fractions were applied to supply 40 mg available P kg(1) to a thermic Rhodic Kanhapludult with pH values of 5.2 +/- 0.05 (unlimed) and 6.4 +/- 0.08 (limed). Wheat (Triticum aestivum L.) grown in a greenhouse for 101 d served as the test crop. The requirement for WSP was source and pH dependent. At a soil pH of 5.2, the fertilizers required 73 to 95% WSP to reach the maximum dry-matter yield, while they required 60 to 86% WSP at pH 6.4. To reach 90% of the maximum yield, all superphosphate fertilizers required <50% WSP. These results show that it is not always necessary to have high water solubility as required by legislation in many countries.

Valorization of grape pomace through hot compressed water extraction/hydrolysis

The world energy consumption is expected to increase strongly in coming years, because of the emerging economies. Biomass is the only renewable carbon resource that is abundant enough to be used as a source of energy Grape pomace is one of the most abundant agro-industrial residues in the world, being a good biomass resource. The aim of this work is the valorization of grape pomace from white grapes (WWGP) and from red grapes (RWGP), through the extraction of phenolic compounds with antioxidant activity, as well as through the extraction/hydrolysis of carbohydrates, using subcritical water, or hot compressed water (HCW). The main focus of this work is the optimization of the process for WWGP, while for RWGP only one set of parameters were tested. The temperatures used were 170, 190 and 210 °C for WWGP, and 180 °C for RWGP. The water flow rates were 5 and 10 mL/min, and the pressure was always kept at 100 bar. Before performing HCW assays, both residues were characterized, revealing that WWGP is very rich in free sugars (around 40%) essentially glucose and fructose, while RWGP has higher contents of structural sugars, lignin, lipids and protein. For WWGP the best results were achieved at 210 °C and 10 mL/min: higher yield in water soluble compounds (69 wt.%), phenolics extraction (26.2 mg/g) and carbohydrates recovery (49.3 wt.% relative to the existing 57.8%). For RWGP the conditions were not optimized (180 °C and 5 mL/min), and the values of the yield in water soluble compounds (25 wt.%), phenolics extraction (19.5 mg/g) and carbohydrates recovery (11.4 wt.% relative to the existing 33.5%) were much lower. The antioxidant activity of the HCW extracts from each assay was determined, the best result being obtained for WWGP, namely for extracts obtained at 210 °C (EC50=20.8 μg/mL; EC50 = half maximum effective concentration; EC50 = 22.1 μg/mL for RWGP, at 180 ºC).

Effect of water and citrate solubility on agronomic effectiveness of acidulated phosphates in three consecutive corn crops

In the process of phosphate rock acidulation, several impure P compounds may be formed along with the desirable Ca and NH4 phosphates. Such compounds normally reduce the content of water-soluble P and thus the agronomic effectiveness of commercial fertilizers. In order to study this problem, a greenhouse experiment consisting of three consecutive corn crops was conducted in samples of a Red-Yellow Latosol (Typical Hapludox) in a completely randomized design (6 x 2 x 2), with four replicates. Six commercial fertilizers were added to 2 kg of soil at a rate of 70 mg kg-1 P, based on the content of soluble P in neutral ammonium citrate plus water (NAC + H2O) of the fertilizers. Fertilizer application occurred either in the original form or leached to remove the water-soluble fraction, either by mixing the fertilizer with the whole soil in the pots or with only 1 % of its volume. The corn plants were harvested 40 days after emergence to determine the shoot dry matter and accumulated P. For the first crop and localized application, the elimination of water-soluble P from the original fertilizers resulted in less bioavailable P for the plants. For the second and third crops, the effects of P source, leaching and application methods were not as evident as for the first, suggesting that the tested P sources may have similar efficiencies when considering successive cropping. The conclusion was drawn that the water-insoluble but NAC-soluble fractions of commercial P fertilizers are not necessarily inert because they can provide P in the long run.

Catalytic gasification of glycerol in supercritical water

The conversion of glycerol in supercritical water (SCW) was studied at 510-550 °C and a pressure of 350 bars using both a bed of inert and non-porous ZrO2 particles (hydrothermal experiments), and a bed of a 1% Ru/ZrO2 catalyst. Experiments were conducted with a glycerol concentration of 5 wt% in a continuous isothermal fixed-bed reactor at a residence time between 2 and 10 s. Hydrothermolysis of glycerol formed water-soluble products such as acetaldehyde, acetic acid, hydroxyacetone and acrolein, and gases like H2, CO and CO2. The catalyst enhanced the formation of acetic acid, inhibited the formation of acrolein, and promoted gasification of the glycerol decomposition products. Hydrogen and carbon oxides were the main gases produced in the catalytic experiments, with minor amounts of methane and ethylene. Complete glycerol conversion was achieved at a residence time of 8.5 s at 510 °C, and at around 5 s at 550 °C with the 1 wt% Ru/ZrO2 catalyst. The catalyst was not active enough to achieve complete gasification since high yields of primary products like acetic acid and acetaldehyde were still present. Carbon balances were between 80 and 60% in the catalytic experiments, decreasing continuously as the residence time was increased. This was attributed partially to the formation of methanol and acetaldehyde, which were not recovered and analyzed efficiently in our set-up, but also to the formation of carbon deposits. Carbon deposition was not observed on the catalyst particles but on the surface of the inert zirconia particles, especially at high residence time. This was related to the higher concentration of acetic acid and other acidic species in the catalytic experiments, which may polymerize to form tar-like carbon precursors. Because of carbon deposition, hydrogen yields were significantly lower than expected; for instance at 550 °C the hydrogen yield potential was only 50% of the stoichiometric value.

Pressurized hot water flow-through extraction of birch wood

Effective processes to fractionate the main compounds in biomass, such as wood, are a prerequisite for an effective biorefinery. Water is environmentally friendly and widely used in industry, which makes it a potential solvent also for forest biomass. At elevated temperatures over 100 °C, water can readily hydrolyse and dissolve hemicelluloses from biomass. In this work, birch sawdust was extracted using pressurized hot water (PHWE) flow-through systems. The hypothesis of the work was that it is possible to obtain polymeric, water-soluble hemicelluloses from birch sawdust using flow-through PHW extractions at both laboratory and large scale. Different extraction temperatures in the range 140–200 °C were evaluated to see the effect of temperature to the xylan yield. The yields and extracted hemicelluloses were analysed to obtain sugar ratios, the amount of acetyl groups, furfurals and the xylan yields. Higher extraction temperatures increased the xylan yield, but decreased the molar mass of the dissolved xylan. As the extraction temperature increased, more acetic acid was released from the hemicelluloses, thus further decreasing the pH of the extract. There were only trace amounts of furfurals present after the extractions, indicating that the treatment was mild enough not to degrade the sugars further. The sawdust extraction density was increased by packing more sawdust in the laboratory scale extraction vessel. The aim was to obtain extracts with higher concentration than in typical extraction densities. The extraction times and water flow rates were kept constant during these extractions. The higher sawdust packing degree decreased the water use in the extractions and the extracts had higher hemicellulose concentrations than extractions with lower sawdust degrees of packing. The molar masses of the hemicelluloses were similar in higher packing degrees and in the degrees of packing that were used in typical PHWE flow-through extractions. The structure of extracted sawdust was investigated using small angle-(SAXS) and wide angle (WAXS) x-ray scattering. The cell wall topography of birch sawdust and extracted sawdust was compared using x-ray tomography. The results showed that the structure of the cell walls of extracted birch sawdust was preserved but the cell walls were thinner after the extractions. Larger pores were opened inside the fibres and cellulose microfibrils were more tightly packed after the extraction. Acetate buffers were used to control the pH of the extracts during the extractions. The pH control prevented excessive xylan hydrolysis and increased the molar masses of the extracted xylans. The yields of buffered extractions were lower than for plain water extractions at 160–170 °C, but at 180 °C yields were similar to those from plain water and pH buffers. The pH can thus be controlled during extraction with acetate buffer to obtain xylan with higher molar mass than those obtainable using plain water. Birch sawdust was extracted both in the laboratory and pilot scale. The performance of the PHWE flow-through system was evaluated in the laboratory and the pilot scale using vessels with the same shape but different volumes, with the same relative water flow through the sawdust bed, and in the same extraction temperature. Pre-steaming improved the extraction efficiency and the water flow through the sawdust bed. The extracted birch sawdust and the extracted xylan were similar in both laboratory and pilot scale. The PHWE system was successfully scaled up by a factor of 6000 from the laboratory to pilot scale and extractions performed equally well in both scales. The results show that a flow-through system can be further scaled up and used to extract water-soluble xylans from birch sawdust. Extracted xylans can be concentrated, purified, and then used in e.g. films and barriers, or as building blocks for novel material applications.

Modification d'acides biliaires à l'aide de polymères pour en moduler les propriétés d'agrégation

Les polymères amphiphiles sont largement utilisés pour les applications biomédicales et pharmaceutiques. Afin d’améliorer les chances de biocompatibilité des nouveaux polymères que nous voulons développer, nous avons utilisé des composés naturels, les acides biliaires, comme produits de départ dans la synthèse de ces polymères. De nouveaux polymères anioniques amphiphiles dérivés de l’acide cholique ont été préparés par polymérisation radicalaire par transfert d’atomes. Par un contrôle rigoureux des conditions de polymérisation, des bras de poly(acide acrylique) de différentes longueurs ont été greffés sur le squelette de l’acide cholique. L’architecture moléculaire des polymères a été étudiée par spectroscopie 1H RMN et par spectrométrie de masse. Ces polymères en étoile formés par l’acide biliaire modifié sont capables de s’agréger dans l’eau même si les groupements hydroxyles ont été remplacés par des segments plus volumineux. Il a été observé que les liaisons ester entre le polymère et le cœur d’acide cholique sont sensibles à l’hydrolyse en solution aqueuse. Pour remédier au problème de stabilité en solution aqueuse et pour avoir, en même temps, des bras hydrophiles non ioniques et biocompatibles, de l’oxyde d’éthylène a été polymérisé sur l’acide cholique par polymérisation anionique. Les liaisons éther formées entre le polymère et les groupements hydroxyles de l’acide biliaire sont plus stables que les liaisons ester sur le polymère de poly(acide acrylique). Les conditions de réaction de la polymérisation anionique ont été optimisées et ont donné des polymères aux architectures et aux masses molaires contrôlées. Les nouveaux polymères forment des agrégats sphériques tel qu’observé par microscopie électronique à transmission avec des échantillons préparés par la méthode de fracture à froid. Leur morphologie est différente de celle des agrégats cylindriques formés par les acides biliaires. Avec la méthode optimisée pour la polymérisation anionique, l’éther d’allyle et glycidyle a été polymérisé sur un dérivé d’acide cholique, suivi par une thiolation des liaisons doubles pour introduire l’amine ou l’acide sur la chaîne polymère. Cette addition radicalaire est efficace à plus de 90%. Les polymères qui en résultent sont solubles dans l’eau et s’agrègent à une certaine concentration critique. Il est particulièrement intéressant d’observer la thermosensibilité des polymères ayant des groupements amine, laquelle peut être modulée en acétylant partiellement les amines, donnant des points nuages entre 15 et 48°C.

Exploring the Factors Affecting the Solubility of Chitosan in Water

We explore the role of crystallinity and inter- or intramolecular forces in chitosan for its solubility in water and demonstrate the expansion of its solubility to a wider pH range. Due to its semicrystalline nature, derived mainly from inter- and intramolecular hydrogen bonds, chitosan is water-soluble only at pH < 6. In acidic conditions, its amino groups can be partially protonated resulting in repulsion between positively charged macrochains, thereby allowing diffusion of water molecules and subsequent solvation of macromolecules. We show that chemical disruption of chitosan crystallinity by partial re-acetylation or physical disruption caused by the addition of urea and guanidine hydrochloride broadens the pH-solubility range for this biopolymer.

Selective catalytic oxidation of alkylaromatic molecules by nanosize water droplets containing Co2+ species in supercritical carbon dioxide fluid

Stabilized nano-sized water droplet carrying water-soluble Co2+ species is employed as a new catalyst system for the oxidation of the alkyl aromatics in the presence of a fluorinated surfactant. This stable system contains no labile C-H structure and can facilitate excellent mixing of catalytic Co(II)/NaBr species, hydrocarbon substrates and oxygen in supercritical carbon dioxide fluid, which is demonstrated to be an excellent alternative solvent system to acetic acid or nitric acid for air oxidation of a number of alkyl aromatic hydrocarbons using Co(II) species at mild conditions. As a result, potential advantages of this 'greener' catalytic method including safer operation, easier separation and purification, higher catalytic activity with selectivity and without using corrosive or oxidation unstable solvent are therefore envisaged.

CERAMIC MATERIAL FROM SEWAGE SLUDGE AS SUPPORT MATERIAL SUPPLY WATER FILTRATION

This study shows a possibility of using municipal sewage sludge after thermal treatment in the production of a filtering material to water treatment. Due to the fast urbanization and implementation of high standards for effluent in many countries in recent years, the sewage sludge is being produced in an ever increasing amount. Therefore, the use of sludge is a suitable solution for the expected large quantity of sludge. Dehydration of sludge was performed by controlled heating at temperatures of 1100 degrees C, 850 degrees C, 650 degrees C, 350 degrees C for 3 hours. After thermal treatment the sludge was characterized by X-ray fluorescence, TG/DTG/DTA, residue solubilization and residue lixiviation tests. The aim of the present work was to observe, thought the characterization techniques, if the treated sewage sludge is or not adequate to be used as filter material to water treatment. It will be verified which treatment temperature of the sludge offer possibility to its use in water treatment without carrying pollutants in concentrations out of the standards.

The effect of sodium chloride on the formation of W/O microemulsions in soy bean oil/surfactant/water systems and the solubilization of small hydrophilic molecules

Partial pseudoternary phase diagrams were constructed for soy bean oil (SBO)/surfactant/NaCl aqueous solution systems, at 25 degrees C, using the anionic sodium bis(2-ethylhexyl) sulfosuccinate (ACT) and zwiterionic phosphatidylcholine (PC) or mixtures of these surfactants. The isotropic single phase of water-in-oil (W/O) microemulsions (MEs) is shown in the phase diagram and their viscosity reported. ME samples containing small amount of surfactant exhibit slightly higher viscosity than pure SBO, and were used in the solubilization of small water soluble molecules. NaCl enhances the area of the ME phase and MEs with different surfactant composition exhibit different induction time as obtained from tests of oxidative stability, and so are the MEs enriched with ascorbic acid, folic acid and FeSO4, with the latter exhibiting lower stability. The so prepared enriched soy bean oil has potential application in food industry since the surfactants are food grade. (C) 2007 Elsevier B.V. All rights reserved.

Development and characterization of biocompatible isotropic and anisotropic oil-in-water colloidal dispersions as a new delivery system for methyl dihydrojasmonate antitumor drug

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Oil-in-water biocompatible microemulsion as a carrier for the antitumor drug compound methyl dihydrojasmonate

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Silicon oxide nitride (sion) films per applicazioni fotovoltaiche

La ricerca, negli ultimi anni, si è concentrata sullo studio di materiali con energy gap più ampio del silicio amorfo a-Si per ridurre gli assorbimenti parassiti all'interno di celle fotovoltaiche ad eterogiunzione. In questo ambito, presso l'Università di Costanza, sono stati depositati layers di silicon oxynitride amorfo a-SiOxNy. Le promettenti aspettative di questo materiale legate all'elevato optical gap, superiore ai 2.0 eV, sono tuttavia ridimensionate dai problemi intrinseci alla struttura amorfa. Infatti la presenza di una grande quantit a di difetti limita fortemente la conducibilita e aumenta gli effetti di degradazione legati alla luce. In quest'ottica, nella presente tesi, sono stati riportati i risultati di analisi spettroscopiche eseguite presso il Dipartimento di Fisica e Astronomia di Bologna su campioni di silicon oxynitride nanocristallino nc-SiOxNy, analisi che hanno lo scopo di osservare come la struttura nanocristallina influisca sulle principali proprieta ottiche e sulla loro dipendenza da alcuni parametri di deposizione.

Polimeri tiofenici funzionali e loro applicazioni nel fotovoltaico

Recentemente, sempre più attenzione è stata rivolta all' utilizzo di coloranti organici come assorbitori di luce per la preparazione di strati fotoattivi in celle solari organiche (OPV). I coloranti organici presentano un'elevata abilità nella cattura della luce solare grazie all'elevato coefficiente di estinzione molare e buone proprietà fotofisiche. Per questi motivi sono eccellenti candidati per l'incremento della conversione fotoelettrica in OPV. In questa tesi viene descritta una nuova strategia per l'incorporazione di derivati porfirinici in catena laterale a copolimeri tiofenici. Gli studi svolti hanno dimostrato che poli(3-bromoesil)tiofene può essere variamente funzionalizzato con idrossitetrafenilporfirina (TPPOH), per l'ottenimento di copolimeri utilizzabili come materiali p-donatori nella realizzazione di OPV. I copolimeri poli[3-(6-bromoesil)tiofene-co-(3-[5-(4-fenossi)-10,15,20-trifenilporfirinil]esil tiofene] P[T6Br-co-T6TPP] contenenti differenti quantità di porfirina, sono stati sintetizzati sia con metodi non regiospecifici che regiospecifici, con lo scopo di confrontarene le proprietà e di verificare se la strutture macromolecolare che presenta una regiochimica di sostituzione sempre uguale, promuove o meno il trasporto della carica elettrica, migliorando di conseguenza l'efficienza. E' stato inoltre effettuato un ulteriore confronto tra questi derivati e derivati simili P[T6H-co-T6TPP] che non contengono l'atomo di bromo in catena laterale con lo scopo di verificare se l'assenza del gruppo reattivo, migliora o meno la stabilità termica e chimica dei film polimerici, agendo favorevolmete sulle performance dei dispositivi fotovoltaici. Tutti i copolimeri sono stati caratterizzati con differenti tecniche: spettroscopia NMR, FT-IR e UV-Vis, analisi termiche DSC e TGA, e GPC. Le celle solari Bulk Heterojunction, preparate utilizzando PCBM come materiale elettron-accettore e i copolimeri come materilai elettron-donatori, sono state testate utilizzando un multimetro Keithley e il Solar Simulator.

Film di silicon oxinitride (sion) per applicazioni fotovoltaiche, studio di transizioni ottiche.

I materiali per applicazioni fotovoltaiche hanno destato un interesse crescente nella comunità scienti�ca negli ultimi decenni. Le celle HIT (Het- erojunction Intrinsic Thin Layer ) sono dispositivi di ultima generazione che hanno raggiunto e�cienza elevata mantenendo bassi i costi di pro- duzione, e impiegano silicio amorfo (a-Si) come strato emettitore per il suo buon assorbimento della luce e silicio cristallino come regione attiva. La struttura amorfa del silicio presenta però una bassa conducibilità, oltre ad e�etti di degradazione che limitano considerevolmente la durevolezza di una cella. Per questo motivo si stanno cercando possibili alternative al silicio amorfo, in particolare strutture multifase e composti di silicio, ossigeno ed azoto. In questo lavoro sono esposti i risultati dell'analisi di sottili lay- er di Silicon Oxynitride ossigenato (SiOx Ny :H), in forma microcristallina, deposti tramite PECVD (P lasma-Enhanced Chemical Vapor Deposition) su vetro presso l'università di Costanza. La forma microcristallina è una distribuzione di agglomerati cristallini dell'ordine di grandezza di un mi- crometro in una matrice di silicio amorfo, e attualmente le sue proprietà ottiche ed elettroniche non sono ancora state studiate in maniera appro- fondita. Nonostante ciò, è invece evidente che la fase microstallina non presenta tanti difetti intrinseci come la forma amorfa e ne è quindi una val- ida alternativa. In questa ottica, si è svolto uno studio sperimentale delle proprietà ottiche di layers in forma microcristallina di SiOx Ny :H, quali la misura del gap energetico. I risultati sperimentali, volti a trovare la dipen- denza delle caratteristiche dai parametri di deposizione dei layers, hanno mostrato una riduzione del gap energetico con la concentrazione di N2 O, uno dei gas precursori utilizzati nella deposizione dei layers in camera di processo. In conclusione si può dire che il μc−SiOx Ny :H ha le buone carat- teristiche tipiche dei semiconduttori cristallini, che unite alla possibilità di regolare il valore del gap energetico in base alle scelte in fase di deposizione, gli conferisce buone prospettive per applicazioni in celle fotovoltaiche, come emettitore in celle ad eterogiunzione.