Determination of chemical elements in africanized Apis mellifera (Hymenoptera: Apidae) honey samples from the State of Piauí, Brazil

Honey is a food used since the most remote times, appreciated for its characteristic flavor, considerable nutritional value and medicinal properties; however, little information exists about the presence of chemical elements in it. The objectives of this work were to determine the chemical elements present in 38 honey samples, collected directly from beekeepers from the State of Piauí, Brazil and to verify whether they presented any contamination. The chemical elements were determined by means of Total Reflection X-ray Fluorescence. The means of three replicates were: K (109.671 ± 17.487), Ca (14.471 ± 3.8797), Ti (0.112 ± 0.07), Cr (0.196 ± 0.11), Mn (0.493 ± 0.103), Fe (1.722 ± 0.446), Co (0.038), Ni (0.728 ± 0.706), Cu (0.179 ± 0.0471), Zn (0.967 ± 0.653), Se (not detected), Br (not detected), Rb (0.371 ± 0.097), Sr (0.145 ± 0.45), Ba (11.681), Hg (not detected), and Pb (0.863) µg g-1.

Separation and preconcentration of copper in environmental samples on Amberlite XAD-8 resin after complexation with a carbothioamide derivative

A new solid phase extraction (SPE) method has been developed for the selective separation and preconcentration of Cu (II) ions in food and water samples prior to its flame atomic absorption spectrometry determination. The method is based on the adsorption of the Cu(II) - 2-{[4-Amino-3-(4-methylphenyl-5-oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl]acetyl}-N-phenyl hydrazinecarbothioamide complex on Amberlite XAD-8 resin. The metal complex retained on the resin was eluted with 7.5 mL of 2.0 mol L-1 HCl in acetone. The optimum conditions for the SPE of Cu(II) ions were investigated, and the method was subsequently applied to sea water, stream water, rice, tea, and tobacco samples for the determination of Cu(II) levels.

Spectrophotometric determination of Sudan Blue II in environmental samples after dispersive liquid-liquid microextraction

A dispersive liquid-liquid microextraction procedure coupled to spectrophotometry is described for the determination of the trace levels of Sudan Blue II. Analytical parameters, such as pH, volume of extraction solvent (carbon tetrachloride), volume of dispersant (ethanol), volume of sample, and extraction time, were optimized. Matrix effects were also investigated. Preconcentration factor was found to be 200. Detection limit and relative standard deviation (RSD) were 0.55 µg L-1 and 3.9%, respectively. The procedure was successfully used for the determination of trace levels of Sudan Blue II in food, ink, antifreeze, and industrial waste-water samples.

Aflatoxin M1 in samples of "minas" cheese commercialized in the city of Belo Horizonte - Minas Gerais/Brazil

Milk products such as cheeses may be contaminated by aflatoxin M1 when dairy cattle have consumed feeds contaminated with aflatoxin B1. Samples of "Minas" cheeses (fresh, canastra and standard) were collected by the Inspection Service in the Mercado Central in Belo Horizonte city, Minas Gerais - Brazil. A purified extract was obtained by extraction with dichloromethane followed by a washing with n-hexane and immunoaffinity column purification. The quantification of aflatoxin M1 was done by high performance liquid chromatography (HPLC) using a fluorescence detector. Recoveries were about 75%. In 56 of the 75 samples (74.7%), the presence of aflatoxin M1 was detected in concentrations ranging between 0.02 and 6.92ng/g of cheese. In the positive cases ( > or = 0.02ng/g) the mean contamination level of aflatoxin M1 was 0.08ng/g in fresh cheese, 0.36ng/g in canastra cheese and 0.62ng/g in standard cheese. No aflatoxin M1 maximum tolerance level in cheese has been established in Brazil.

Distribution of aflatoxin contamination in maize samples

The distribution of the aflatoxin contamination was studied among four maize fractions, separated according to Brazilian grading rules for maize. The fraction that contained fermented, moldy, heated and sprouted grains normally had the highest levels of aflatoxin. However, the fraction contribution to the whole sample contamination level took into account the contamination fraction level and its weight to the whole sample. Considering this, the fraction that contained insect damaged, hollow, up to ¼ fermented and grains damaged by other causes was normally the fraction responsible for the total contamination level in the samples. Nevertheless, the fraction contributions were variable from sample to sample. Therefore, in conclusion, it was not possible to establish a standard behavior for grain fraction-type contribution for different maize lots. The Brazilian grading by qualitative types applied to samples did not show statistic correlation with aflatoxin contamination levels (P<0.05). Two type-1 samples (the best quality type) presented contamination of 380 and 146ng/g. The number of samples with contamination levels above those allowed by Brazilian law (20ng/g) was the same for qualitative types 2, 3, and BS (Below Standard).

Natural radiation levels in powdered milk samples

The control and monitoring of radioactive elements in foodstuffs is fundamental for human health maintenance. This work presents procedures to measure radioactivity levels in powdered milk samples and also a brief discussion of radionuclide transference from the environment to mankind. The measurements were performed utilizing a high-resolution gamma-ray spectrometer using an HPGe detector. The results allowed the quantification of 40K, 137Cs and 208Tl radionuclides. For 40K the average activity was 482 ± 37 Bq/kg and for 137Cs and 208Tl the lower level of detection was, respectively, 3.7 ± 1.1 and 0.5 ± 0.2 (Bq/kg). The results obtained for the milk samples were compared to data found in the literature and to the limits established by the Brazilian National Commission of Nuclear Energy (CNEN) to assure its safety to human consuption.

Detection and quantification of Roundup Ready® soybean residues in sausage samples by conventional and real-time PCR

The increasing presence of products derived from genetically modified (GM) plants in human and animal diets has led to the development of detection methods to distinguish biotechnology-derived foods from conventional ones. The conventional and real-time PCR have been used, respectively, to detect and quantify GM residues in highly processed foods. DNA extraction is a critical step during the analysis process. Some factors such as DNA degradation, matrix effects, and the presence of PCR inhibitors imply that a detection or quantification limit, established for a given method, is restricted to a matrix used during validation and cannot be projected to any other matrix outside the scope of the method. In Brazil, sausage samples were the main class of processed products in which Roundup Ready® (RR) soybean residues were detected. Thus, the validation of methodologies for the detection and quantification of those residues is absolutely necessary. Sausage samples were submitted to two different methods of DNA extraction: modified Wizard and the CTAB method. The yield and quality were compared for both methods. DNA samples were analyzed by conventional and real-time PCR for the detection and quantification of Roundup Ready® soybean in the samples. At least 200 ng of total sausage DNA was necessary for a reliable quantification. Reactions containing DNA amounts below this value led to large variations on the expected GM percentage value. In conventional PCR, the detection limit varied from 1.0 to 500 ng, depending on the GM soybean content in the sample. The precision, performance, and linearity were relatively high indicating that the method used for analysis was satisfactory.

Optimization and validation of a methodology to determine total arsenic, As(III) and As(V), in water samples, through graphite furnace atomic absorption spectrometry

The Graphite furnace atomic absorption spectrometry (GF AAS) was the technique chosen by the inorganic contamination laboratory (INCQ/ FIOCRUZ) to be validated and applied in routine analysis for arsenic detection and quantification. The selectivity, linearity, sensibility, detection, and quantification limits besides accuracy and precision parameters were studied and optimized under Stabilized Temperature Platform Furnace (STPF) conditions. The limit of detection obtained was 0.13 µg.L-1 and the limit of quantification was 1.04 µg.L-1, with an average precision, for total arsenic, less than 15% and an accuracy of 96%. To quantify the chemical species As(III) and As(V), an ion-exchange resin (Dowex 1X8, Cl- form) was used and the physical-chemical parameters were optimized resulting in a recuperation of 98% of As(III) and of 90% of As(V). The method was applied to groundwater, mineral water, and hemodialysis purified water samples. All results obtained were lower than the maximum limit values established by the legal Brazilian regulations, in effect, 50, 10, and 5 µg.L-1 para As total, As(III) e As(V), respectively. All results were statistically evaluated.

Effect of soaking and cooking on phytate concentration, minerals, and texture of food-type soybeans

The increasing consumption of soybeans due to its bioactive compounds has attracted interest in describing the grain's constituents and variation during processing. Phytate has been the aim of much research since it chelates essential minerals but also has beneficial antioxidant effects. This study evaluated the variation of phytate, calcium, zinc, and iron during soaking and cooking of soybeans. The phytate: Zn and phytate: Fe molar ratios were determined in order to estimate the bioavailability of these minerals. Six food-type varieties were used: BR 36, BRS 213, BRS 216, BRS 232, BRS 155, and Embrapa 48. The samples were soaked in water 3:1 (w/w) for 12 hours at room temperature and cooked. Cooking time was determined by modeling the softening of each variety using fractional conversion. Water content, phytate, and minerals were determined in raw, soaked and cooked samples. The water content of raw grains for all varieties was 9.9 g.100 g-1 increasing to a range of 58.1-63.7 g.100 g-1 after soaking and 63.1-66.0 g.100 g-1 after cooking. Soaking caused a significant reduction in phytate (23-30%), but cooking caused no additional reduction. The phytate: Zn molar ratio was 20 indicating that zinc absorption could be impaired, while the phytate: Fe molar ratio was 8, below the level of compromising absorption

Pre-treatment of thermoduric spores in CO2 modified atmosphere and their survivability during food extrusion

The aim of this experiment was to evaluate how susceptible spores become to mechanical damage during food extrusion after being submitted to CO2. B. stearothermophilus spores sowed to corn and soy mix were submitted to 99% CO2 for 10 days and extruded in a single-screw extruder. The treatments were: T1 - spore-containing samples, extruded at screw rotational speed of 65 rpm and barrel wall temperature of 80 °C; T2 - as T1, except for screw rotational speed of 150 rpm; and T3 - as T2, except that samples were submitted to the modified atmosphere. The results for cell viability, minimum and maximum residence times, and static pressure were T1 - 19.90 ± 3.24%, 123.3 ± 14.50 seconds; 203.3 ± 14.05 seconds; 2.217 ± 62 kPa; T2 - 21.42 ± 8.24%, 70.00 ± 5.77 seconds; 170.00 ± 4.67 seconds; 2.310 ± 107 kPa; and T3 - 11.06 ± 2.46%, 86.00 ± 7.23 seconds; 186.00 ± 7.50 seconds; 2.403 ± 93 kPa, respectively. It was concluded that the extrusion process did reduce the cell count. However, screw rotational speed variation or CO2 pre-treatment did not affect cell viability.

Comparison of methodologies for moisture determination on dried bee pollen samples

Bee pollen moisture value is one of the quality parameters for this product. Some countries such as Argentina, Brazil, Bulgaria, Poland and Switzerland have bee pollen regulations on quality parameters, but these are not clear regarding which method should be used for moisture determination. The aim of this paper was to compare six methods of moisture determination in dried bee pollen samples. The methods were: conventional oven at 100 °C, vacuum oven at 70 °C, desiccator with sulfuric acid, drying out process with infrared light at 85 °C, lyophilization and Karl Fisher's method. Based on the results, the best methods for moisture determination of bee pollen were the drying process with infrared and the lyophilization, since these have shown lower moisture values.

Searching to combine technologies for safer food attainment

Campylobacteriosis is an infection frequently acquired through the consumption of animal origin products. Chicken can be considered the main responsible cause in the transmission chain of this disease. Ionizing radiation was used to verify the reduction of the microbiological load of Campylobacter jejuni present in chicken liver, which, in natura, can present contamination in up to 100% of the cases. The doses of irradiation used were: 0.20 kGy, 0.27 kGy, 0.30 kGy and 0.35 kGy. The samples of chicken liver were acquired in aviaries, local supermarkets and large chain supermarkets. The samples were analyzed for Campylobacter at FIOCRUZ. Irradiation was performed at COPPE/UFRJ, using a Gamma Cell Irradiator with a 60Co gamma source. Only the frozen sample acquired at the local supermarket did not contain the bacterium. Campylobacter sp. was present in all other samples, even when using procedures and technologies that aimed at the impediment of the presence of this bacterium in food and, consequently, at the protection of human health. On the whole, the results were satisfactory; nevertheless, it is known that the bacterial growth conditions required by this bacterium are uncommon when compared to other enteropathogenic bacteria.

Cassava starch in the Brazilian food industry

Cassava starch is a valued raw material for producing many kinds of modified starches for food applications. Its physicochemical properties, as well as its availability, have made it an interesting and challenging ingredient for the food industry. In the present work, food grade modified cassava starches were purchased from producers and analyzed for selected physicochemical characteristics. Samples of sour cassava starch were included, as well as one sample of native cassava starch. Results showed that almost all modified starches were resistant to syneresis, produced pastes more stable to stirred cooking, and some of them were difficult to cook. The sour cassava starches presented high acidity and resulted in clear and unstable pastes during stirred cooking, susceptible to syneresis.

Detection of enterotoxins produced by B. cereus through PCR analysis of ground and roasted coffee samples in Rio de Janeiro, Brazil

Coffee is one of the most appreciated drinks in the world. Coffee ground is obtained from the fruit of a small plant that belongs to the genus Coffea. Coffea arabica and Coffea canephora robusta are the two most commercially important species. They are more commonly known as arabica and robusta, respectively. Two-thirds of Coffea arabica plants are grown in South and Central America, and Eastern Africa - the place of origin for this coffee species. Contamination by microorganisms has been a major matter affecting coffee quality in Brazil, mainly due to the harvesting method adopted. Brazilian harvests are based on fruits collected from the ground mixed with those that fall on collection cloths. As the Bacillus cereus bacterium frequently uses the soil as its environmental reservoir, it is easily capable of becoming a contaminant. This study aimed to evaluate the contamination and potential of B. cereus enterotoxin genes encoding the HBL and NHE complexes, which were observed in strains of ground and roasted coffee samples sold in Rio de Janeiro. The PCR (Polymerase Chain Reaction) results revealed high potential of enterotoxin production in the samples. The method described by Speck (1984) was used for the isolation of contaminants. The investigation of the potential production of enterotoxins through isolates of the microorganism was performed using the B. cereus enterotoxin Reverse Passive Latex Agglutination test-kit (BCET-RPLA, Oxoid), according to the manufacturer's instructions. The potential of enterotoxin production was investigated using polymerase chain reaction (PCR) methods for hblA, hblD and hblC genes (encoding hemolysin HBL) and for nheA, nheB and nheC genes (encoding non-hemolytic enterotoxin - NHE). Of all the 17 strains, 100% were positive for at least 1 enterotoxin gene; 52.9% (9/17) were positive for the 3 genes encoding the HBL complex; 35.3% (6/17) were positive for the three NHE encoding genes; and 29.4% (5/17) were positive for all enterotoxic genes.

Microbial flora in organic honey samples of africanized honeybees from Parana river islands

The purpose of this study was to verify and compare the main contamination sources and the hygienic/sanitary conditions of organic honey samples of Apis mellifera from Parana River islands. Thirty-three (33) samples were analyzed between January 2005 and August 2006. Eleven (11) samples were collected by beekeepers and twenty-two (22) samples were collected and processed in accordance with ideal personal hygiene norms and good manufacturing practices. The samples underwent microbiological analysis in search of coliforms at 35 ºC and 45 ºC, as well as fungi enumeration analysis. As for fungi counting, the samples harvested by beekeepers showed values above the maximum established by Resolution nº 15/94 of Common Market Group - Mercosul. The results showed that secondary contamination sources are responsible for the reduction of organic honey quality.