Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

Public-private partnership in marine litter waste management

Marine litter is an international environmental problem that causes considerable costs to coastal communities and the fishing industry. Several international and national treaties and regulations have provisions to marine litter and forbid disposal of waste into the sea. However, none of these regulations state a responsibility for public authorities to recover marine litter from the sea, like they do for marine litter that washes up on public beaches. In a financial evaluation of a value chain for marine litter incineration it was found out that the total costs of waste incineration are approximately 100 ─ 200 % higher than waste fees offered by waste contractors of ports. The high costs of incineration are derived from the high calorific value of marine litter and therefore a high incineration cost for the waste, and long distances between ports that are taking part in a project for marine litter recovery from the sea and an Energy-from-Waste (EfW) facility. This study provides a possible solution to diverting marine litter from landfills to more environmentally sustainable EfW use by using a public-private partnership (PPP) framework. PPP would seem to fit as a suitable cooperative approach for answering problems of current marine litter disposal in theory. In the end it is up to the potential partners of this proposed PPP to decide whether the benefits of cooperation justify the required efforts.

Current status of the waste-to-energy chain in the County of North Savo, Finland

The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

Physical and chemical characterization of the pulp of different varieties of avocado targeting oil extraction potential

The aim of this study was to evaluate the physicochemical properties of avocado pulp of four different varieties (Avocado, Guatemala, Dickinson, and Butter pear) and to identify which has the greatest potential for oil extraction. Fresh avocado pulp was characterized by moisture, protein, fat, ash, carbohydrates and energy contents were determined. The carotenoids and chlorophyll contents were determined by the organic solvent extraction method. The results showed significant differences in the composition of the fruit when varieties are compared. However, the striking feature in all varieties is high lipid content; Avocado and Dickinson are the most suitable varieties for oil extraction, taking into account moisture content and the levels of lipids in the pulp. Moreover, it could be said that the variety Dickinson is the most affected by the parameters evaluated in terms of overall quality. Chlorophyll and carotenoids, fat-soluble pigments, showed a negative correlation with respect to lipids since it could be related to its function in the fruit. The varieties Avocado and Dickinson are an alternative to oil extraction having great commercial potential to be exploited thus avoiding waste and increasing farmers’ income.

Chemical characterization of the flour of peel and seed from two papaya cultivars

Papaya is among the currently most important tropical fruits grown in Brazil and in the world. The fruit is mainly consumed fresh although it offers many industrial products. The processing of this fruit, as well as its fresh consumption, results in large amounts of waste, such as peels and seeds. Papaya consumption is one of the causes of significant loss of food value; therefore, new aspects on the use of its waste as by-products, or in the production of food additives, or even the incorporation of its flour in food have aroused great interest because these are products of high nutritional value, and their use may be economically viable. The objective of this study was to produce and characterize peel and seed flours from two papaya cultivars (Havai and Calimosa) for their chemical constituents focusing on possible use in foods. The proximate and mineral composition, titratable acidity, soluble solids, pH, contents of vitamin C, and phenolic compounds were determined. According to the results obtained, the papaya peel and seed flours had high contents of protein and fiber and therefore can be used as alternative sources of nutrients and can also be added in foods avoiding waste and adding value to the fruit.

Physicochemical and sensory characteristics of snack made with minced Nile tilapia

Nile tilapia is one of the major fish species cultivated worldwide and in Brazil. The tilapia fillet yield is between 30-35%, thus around 70% of waste is generated. A portion of this waste can be used to obtain minced fish, and the resulting product can be used as meat raw material to prepare fish snacks. The aim of this study was to produce fish snacks containing different inclusion levels (20, 30, and 40%) of minced fish obtained from Nile tilapia processing waste and evaluate their physicochemical characteristics and sensory acceptance. Protein content, ash, water activity, and hardness increased with increasing inclusion of minced fish. The scores obtained in the sensory evaluation were: flavor acceptance (from 7.2 to 5.7), texture (from 7.4 to 5.3), overall acceptance (from 7.1 to 5.9), and willingness to purchase (from 4.0 to 3.1). This study demonstrates that the inclusion of 20 to 40% of minced fish of Nile tilapia in snacks is well accepted and improves their nutritional value without affecting the physicochemical properties.

A point-prevalence survey of antimicrobial utilisation within New Brunswick hospitals to focus antimicrobial stewardship efforts and decrease low-value care.

Introduction: Il est important de minimiser le gaspillage et les risques associés aux soins sans valeur. La gestion de l’utilisation des antimicrobiens vise à optimiser leur emploi et doit être adaptée au milieu et à sa population. Objectifs: Évaluer les profiles d’utilisation actuels des antimicrobiens et fixer des objectifs pour les interventions en matière de gestion des antimicrobiens. Méthode: Vingt-et-un hôpitaux du Nouveau-Brunswick offrant des soins de courte durée en médecine générale, en chirurgie et en pédiatrie ont pris part à une enquête sur la prévalence ponctuelle. Tous les patients admis aux hôpitaux participants et ayant reçu au moins un antimicrobien systémique ont été inscrits à l’étude. Les principaux critères d’évaluation étaient le profil d’utilisation, selon l’indication et l’antimicrobien prescrit, le bienfondé de l’utilisation et la durée de la prophylaxie chirurgicale. Des statistiques descriptives et un test d’indépendance 2 furent utilisés pour l’analyse de données. Résultats: L’enquête a été menée de juin à août 2012. Un total de 2244 patients ont été admis pendant la durée de l’étude et 529 (23,6%) ont reçu un antimicrobien. Au total, 691 antimicrobiens ont été prescrits, soit 587 (85%) pour le traitement et 104 (15%) pour la prophylaxie. Les antimicrobiens les plus souvent prescrits pour le traitement (n=587) étaient des classes suivantes : quinolones (25,6%), pénicillines à spectre étendu (10,2%) et métronidazole (8,5%). Les indications les plus courantes du traitement étaient la pneumonie (30%), les infections gastro-intestinales (16%) et les infections de la peau et des tissus mous (14%). Selon des critères définis au préalable, 23% (n=134) des ordonnances pour le traitement étaient inappropriées et 20% (n=120) n’avaient aucune indication de documentée. Les domaines où les ordonnances étaient inappropriées étaient les suivants : défaut de passage de la voie intraveineuse à la voie orale (n=34, 6%), mauvaise dose (n=30, 5%), traitement d’une bactériurie asymptomatique (n=24, 4%) et doublement inutile (n=22, 4%). Dans 33% (n=27) des cas, les ordonnances pour la prophylaxie chirurgicale étaient pour une période de plus de 24 heures. Conclusions: Les résultats démontrent que les efforts de gestion des antimicrobiens doivent se concentrer sur les interventions conventionnelles de gestion de l’utilisation des antimicrobiens, l’amélioration de la documentation, l’optimisation de l’utilisation des quinolones et la réduction au minimum de la durée de la prophylaxie chirurgicale.

Selection of Marine Yeasts for the Generation of Single Cell Protein from Prawn-shell Waste

Marine yeasts (33 strains) were isolated from the coastal and offshore waters off Cochin. The isolates were identified and then characterized for the utilization of starch, gelatin, lipid, cellulose, urea, pectin, lignin, chitin and prawn-shell waste. Most of the isolates were Candida species. Based on the biochemical characterization, four potential strains were selected and their optimum pH and NaCI concentration for growth were determined. These strains were then inoculated into prawn-shell waste and SCP (single cell protein) generation was noted in terms of the increase in protein content of the final product.

Analytical methodologies based on X-Ray Fluorescence Spectrometry (XRF) and Inductively Couple Plasma Spectroscopy (ICP) for the assessment of metal dispersal around mining environments

La investigació que es presenta en aquesta tesi es centra en l'aplicació i millora de metodologies analítiques existents i el desenvolupament de nous procediments que poden ser utilitzats per a l'estudi dels efectes ambientals de la dispersió dels metalls entorn a les zones mineres abandonades. En primer lloc, es van aplicar diferents procediments d'extracció simple i seqüencial per a estudiar la mobilitat, perillositat i bio-disponibilitat dels metalls continguts en residus miners de característiques diferents. Per altra banda, per a estudiar les fonts potencials de Pb en la vegetació de les zones mineres d'estudi, una metodologia basada en la utilització de les relacions isotòpiques de Pb determinades mitjançant ICP-MS va ser avaluada. Finalment, tenint en compte l'elevat nombre de mostres analitzades per a avaluar l'impacte de les activitats mineres, es va considerar apropiat el desenvolupament de mètodes analítics d'elevada productivitat. En aquest sentit la implementació d'estratègies quantitatives així com l'aplicació de les millores instrumentals en els equips de XRF han estat avaluades per a aconseguir resultats analítics fiables en l'anàlisi de plantes. A més, alguns paràmetres de qualitat com la precisió, l'exactitud i els límits de detecció han estat curosament determinats en les diverses configuracions de espectròmetres de XRF utilitzats en el decurs d'aquest treball (EDXRF, WDXRF i EDPXRF) per a establir la capacitat de la tècnica de XRF com a tècnica alternativa a les clàssiques comunament aplicades en la determinació d'elements en mostres vegetals.

Towards effective water reuse: drivers, challenges and strategies shaping the organisational management of reclaimed water in Jordan

Treated wastewater or reclaimed water is gaining recognition as a valuable water resource around the world. To assess why, where and how water reuse takes place in Jordan, semi-structured interviews were conducted with representatives of 29 key organisations in 2008. The analysis reveals that water scarcity is a key driver for water reuse. However, despite such recognition, reuse was described positively by only a small proportion of the interviewees (n = 6). Negative and neutral perceptions regarding reuse dominated and the research found that this was related to two underlying challenges: (i) the requirement for more intensive management when using reclaimed water compared with freshwater and (ii) concern over societal acceptance of water reuse. These factors were found to be associated with the risks posed to humans and their environments, combined with negative emotional and cultural responses to human waste and its applications. Numerous strategies are identified that are employed by organisations to overcome these challenges. Wastewater treatment, regulation, monitoring, the mixing of treated effluent with freshwater and limited public discussion of water reuse are all employed to achieve maximum use of reclaimed water. Each strategy presents benefits of sort, but some may paradoxically also inhibit optimal use of reclaimed water. Careful modifications to the existing strategies of Jordanian agencies, such as more open discussion of reuse, could lead to greater social, economic and environmental gains.

Discerning policy and drivers for sustainable facilities management practice

Due to the changing nature of the facilities management (FM) profession, facilities managers are increasingly engaged with the evolving sustainability agenda in the UK and the development or uptake of sustainability policies within their organisations. This study investigates how facilities managers are engaging with the sustainability agenda and the drivers, policy issues and information they use to improve their sustainability performance management. A web based self-administered questionnaire survey of facilities managers in the UK was conducted to identify drivers and issues that influence and support good sustainable practices. A total of 268 facilities managers responded. The results indicate that legislation is the most important driver for the implementation of sustainable practices. Corporate image and Organisational ethos are also recognised. However demand for efficient monitoring, management and reporting on environmental impact is not highly rated even though the top three issues of sustainability managed by facilities managers are energy management, waste and recycling management and carbon footprint. In addition, facilities managers are expected to take ownership of activities assigned to the reduction of carbon emission. Government industries and organisation with high turnover are more likely to have a sustainability policy. Financial constraints are the main barriers while legislations are the main driver for implementing sustainability. For non-profit organisations and the charitable sector, financial constraints are no hindrance to implementing a sustainability policy. The conclusion drawn is that sustainability agendas continue to be influenced by regulated environmental issues rather than a balanced approach which takes into consideration the wider social and economic aspects of sustainability. While this scenario is far from ideal, the expectation is that the organisation will trust FM to take a vital role in delivering a comprehensive sustainability policy due to the rising tide of legislation, public scrutiny, as well as the needed business case for genuinely embracing sustainability. However, as the integration of sustainability with core business strategies is continuously evolving the emphasis on different drivers will vary from organisation to organisation as well as the responsibilities of facilities managers.

Food geographies I: relational foodscapes and the busy-ness of being more-than-food

The study of foodscapes has spread throughout geography at the same time as food scholarship has spearheaded post-disciplinary research. This report argues that geographers have taken to post-disciplinarity to explore the ways that food is ‘more-than-food’ through analyses of the visceral nature of eating and politics and the vital (re)materializations of food’s cultural geographies. Visceral food geographies illuminate what I call the ‘contingent relationalities’ of food in the critical evaluation of the indeterminate, situated politics of ‘feeling food’ and those of the embodied collectivities of obesity. Questions remain, however, about how a visceral framework might be deployed for broader critiques within foodscapes and the study of human geography. The study of food’s vital materialisms opens up investigation into the practices of the ‘makings’ of meat, food waste and eating networks. Analysis of affect, embodiment and cultural practices is central to these theorizations and suggests consideration of the multiple materialisms of food, space and eating. There is, I contend, in the more radical, ‘post-relational’ approaches to food, the need for a note of caution. Exuberant claims for the ontological, vital agency of food should be tempered by, or at least run parallel to, critical questions of the real politik of political and practical agency in light of recent struggles over austerity, food poverty and food justice.

A study of the chemical and physical properties of cashew nut shell ash for use in cement materials.

A study of the chemical and physical properties of cashew nut shell ash for use in cement materials. Ash occupies a prominent place among agro-industrial wastes, as it is derived from energy generation processes. Several types of ash have pozzolanic reactivity, and might be used as replacement material for cement, resulting in less energy waste and lower cost. This work aimed to investigate the physical and chemical properties of the cashew nut shell ash (CNSA), by performing the following measurement tests: chemical analysis, bulk density, specific mass, leaching and solubilization process, X-ray diffraction (XrD), specific surface area (BET) and pozzolanicity analysis with cement and lime. The results indicate a low reactivity of CNSA and the presence of heavy metals, alkalis and phenol.