A Mechanism for the Occurrence of Ions in Distilled Water

Solar distillation can be used to produce potable water from contaminated water. However, studies show that ions such as F(-) and NO(3)(-) occur in distillates from solar stills. In order to understand the reasons for this behavior, imaging and distillation experiments were conducted. White dots were seen in the vapor space above the interface of hot water poured into containers. The concentrations of various ions such as F(-) and SO(4)(2-) in the distillates from thermal and solar distillation experiments were roughly comparable when the feed consisted of deionized water and also solutions having fluoride concentrations of 100 and 10 000 mg/L. These observations suggest that aerosols enter the distillation setup through leaks and provide nuclei for the condensation of water vapor. The water-soluble component of aerosols dissolves in the drops formed, and some of the drops are transferred to the distillate by buoyancy-driven convection.

Influence Of Free Surface Curvature Of A Liquid Layer On The Critical Marangoni Convection

The Pearson instability was suggested to discuss the onset of Marangoni convection in a liquid layer of large Prandtl number under an applied temperature difference perpendicular to the free surface in the microgravity environment. In this case, the temperature distribution on the curved free surface is nonuniform, and the thermocapillary convection is induced and coupled with the Marangoni convection. In the present paper the effect of volume ratio of the liquid layer on the critical Marangoni convection and the corresponding spatial variation of the convection structure in zero-gravity condition were numerically investigated by two-dimensional model. (C) 2008 Elsevier Ltd. All rights reserved.

Computer Simulation Of Random Sphere Packing In An Arbitrarily Shaped Container

Most simulations of random sphere packing concern a cubic or cylindric container with periodic boundary, containers of other shapes are rarely studied. In this paper, a new relaxation algorithm with pre-expanding procedure for random sphere packing in an arbitrarily shaped container is presented. Boundaries of the container are simulated by overlapping spheres which covers the boundary surface of the container. We find 0.4 similar to 0.6 of the overlap rate is a proper value for boundary spheres. The algorithm begins with a random distribution of small internal spheres. Then the expansion and relaxation procedures are performed alternately to increase the packing density. The pre-expanding procedure stops when the packing density of internal spheres reaches a preset value. Following the pre-expanding procedure, the relaxation and shrinking iterations are carried out alternately to reduce the overlaps of internal spheres. The pre-expanding procedure avoids the overflow problem and gives a uniform distribution of initial spheres. Efficiency of the algorithm is increased with the cubic cell background system and double link data structure. Examples show the packing results agree well with both computational and experimental results. Packing density about 0.63 is obtained by the algorithm for random sphere packing in containers of various shapes.

Attractor crisis and bursting in a fluid flow with two no-slip directions

Characteristic burtsing behavior is observed in a driven, two-dimensional viscous flow, confined to a square domain and subject to no-slip boundaries. Passing a critical parameter value, an existing chaotic attractor undergoes a crisis, after which the flow initially enters a transient bursting regime. Bursting is caused by ejections from and return to a limited subdomain of the phase space, whereas the precrisis chaotic set forms the asymptotic attractor of the flow. For increasing values of the control parameter the length of the bursting regime increases progressively. Passing another critical parameter value, a second crisis leads to the appearance of a secondary type of bursting, of very large dynamical range. Within the bursting regime the flow then switches in irregular intervals from the primary to the secondary type of bursting. Peak enstrophy levels for both types of bursting are associated to the collapse of a primary vortex into a quadrupolar state.

Comparison of Torpedograss and Pickerelweed Susceptibility to Glyphosate

Torpedograss (Panicum repens L.) is one of the most invasive exotic plants in aquatic systems. Repeat applications of (N-phosphonomethyl) glycine (glyphosate) herbicides provide limited control of torpedograss; unfortunately, glyphosate often negatively impacts most non-target native species that grow alongside the weed. This experiment studied the effect of glyphosate on pickerelweed (Pontederia cordata L.), a native plant that shares habitats with torpedograss. Actively growing plants of torpedograss and pickerelweed were cultured in 8-liter containers and sprayed to wet with one of four rates of glyphosate: 0%, 0.75%, 1.0%, or 1.5%. Each treatment included a surfactant to aid in herbicide uptake and a surface dye to verify uniform application of the treatments. All herbicide treatments were applied with a backpack sprayer to intact plants and to cut stubble of both species. Four replicates were treated for each species-rategrowth combination during each of two experiment periods. Plant dry weights 8 weeks after herbicide application suggest that torpedograss was effectively controlled by the highest rate of glyphosate applied to cut stubble. Pickerelweed was unaffected when the highest rate of glyphosate was applied as a cut-and-spray treatment. These data suggest that a cut-and-spray application of a 1.5% solution of glyphosate may be an effective strategy to control torpedograss without deleteriously affecting pickerelweed. (PDF contains 4 pages.)

Der Haftwasseranteil bei Heringsanlandungen über Bandwaagen

In 2004 the fish processing company Euro-Baltic Fischverarbeitungs GmbH Mukran, went into operation on the Isle of Rügen at the Baltic coast of Germany. About 20 % of the herring landed there is discharged from the cutters into the processing plant by pipes, driven by pumps, in case that the landed volume exceeds 10 t fresh weight. In such case the herring is transported in water suspension by means of a pressure-vacuum suction pump system into containers and further transported via conveyer belt to a flowscale. During this process most of the water runs off. It is however unknown how much water remains with the fish and is eventually weighted as fish. To estimate this proportion the mixture of water and fish was stored in special transport containers, which allow the measurement of the run-off. As a result the study shows that on average 2 % of weight measured by the tape scale is water. Along with this factors were determined which influence the variability of the proportion of water.

Der Anteil Transportwasser bei Heringsanlandungen mittels Vakuumsauganlage in Großraumbehältern

Estimation of the water content of herring landings caused by pressure-vacuum double tank pumps and using of multi purpose transport containers About 80 % of herring that is landed in the fish processing company Euro-Baltic Fischverarbeitungs GmbH Mukran, on the Isle of Rügen at the Baltic coast is transported from the cutter into the processing plant by pumping. For this purpose 700 l-Euro-size polyethylene tubs (containers) are filled with herring by means of a pressure-vacuum pump-systems during the unloading of the cutter. To be able to pump the fish from the hold on board it is kept floating in water (transport water). At the end of the pumping/transporting process the fish ends in a dewatering box before reaching the tub, where the transport water is separated from the fish. Then, the not completely dewatered fish is slipped into the transport containers. The amount of transport water reaching the containers depends on the type of PV-equipment and on the amount of transport water in the fish holds of the different cutters. Methodologically the mixture of fish and water must be weighed together. For the experiments specially designed transport container were used which allow the measurement of the run-off of the water to be quantified and thus to measure the proportion of water remaining with the fish. Based on 30 experiments it could be shown that on average 6 % of remaining weight of the mixture is water. Furthermore, factors were detected which influence the variability of the proportion of water.

Qualitätsveränderung von rohen Fischfilets bei Kühlschrank-Lagerung

Raw fillets of saithe, red fish and salmon were stored over a period of 2 days at 6 to 9 °C before preparing by frying, deep-frying or cooking in a microwave oven. The raw and prepared fillets were tested for bacterial loads, TVBN (total volatile basic nitrogene) and for the sensorial status. It was shown that saithe and red fish started more rapidly to spoil under these conditions than salmon. The fillets showed growing bacterial populations and produced high amounts of TVBN. Sensory changes, especially in flavour and odour, took place but the scores kept in an acceptable range. The investigations indicated that it is possible to store raw fillets for 1 or even 2 days in refrigerator but due to the loss of quality it is recommended to use only really fresh fillets stored in very clean containers. It was further shown that it is very important to heat fillets sufficiently during cooking or frying in order to destroy all microorganisms and to obtain safe and stable meals.

Growth response and survival of F1 hybrid fry of Heterobranchus longifilis and Clarias gariepinus reared in glass aquaria and plastic basins

The growth response of F1 hybrid fry of female Heterobranchus longifilis and male Clarias gariepinus were investigated under laboratory conditions in glass aquaria glass tanks and plastic basins. The larvae were produced artificially after inducement with Ovarptim. The hatching percentage was very high. Weekly mean length and weight were monitored for 6 weeks. The average length increase was higher in aquaria glass tanks than in plastic basins. However, there were depressed and irregular weight increases in both types of rearing troughs while significant weight increase (P<0.05) was recorded at week 6 in the plastic basin. Generally, the growth rate and survival in both containers were not significantly different

Emprego da técnica de emissão por fluorescência de ultravioleta no monitoramento de inibidores de corrosão em água produzida

Para aumentar os volumes de extração de petróleo, resolver e prevenir problemas nas operações de produção são utilizados diversos produtos químicos, dentre os quais se destacam os inibidores de corrosão, que são utilizados em toda cadeia produtiva do petróleo visando proteger o sistema da deterioração por corrosão. Os sais de amônio quaternário são uma das classes de inibidores mais utilizadas pela indústria do petróleo devido a sua grande eficiência. Entretanto, sua solubilidade em água faz com que estejam presentes na água produzida representando um risco para contaminação ambiental, visto que possuem baixa biodegrabilidade e potencial de bioacumulação. Como se encontram misturados a outros produtos químicos e sob efeitos das variações do ambiente em que são aplicados, definir um método de análise confiável e viável para monitoramento em linha representa um desafio para os laboratórios de campos de produção. Neste trabalho, foi estudado o emprego da fluorescência de ultravioleta na quantificação de um inibidor de corrosão do tipo sal de amônio quaternário em água. Foram obtidos espectros de emissão do produto comercial em água, além do estudo de variáveis instrumentais e interferentes presentes na água produzida. A comparação com padrões de sal de amônio quaternário permitiu identificar como principal fluorófilo, um sal alquil-aril de amônio quaternário. Estudos de estabilidade revelaram que a adsorção do inibidor de corrosão nas superfícies dos frascos plásticos provoca a queda do sinal fluorescente e que a adição de isopropanol reduz este efeito de 40 para 24%. Foram obtidas curvas de calibração com a formulação comercial e com o cloreto de 2-metil-4-dodecil-benzil-trimetil amônio com uma boa correlação. Amostras sintéticas do inibidor foram determinadas com um erro relativo de 2,70 a 13,32%. O método de adição padrão foi avaliado usando uma amostra de água produzida, e os resultados não foram satisfatórios, devido à interferência, principalmente, de compostos orgânicos aromáticos presentes

Desarrollo de sistemas constructivos de aplicación al edificio industrial del futuro: su adaptabilidad a los sistemas de producción.

[EN]In this project are going to be defined some needs of the industry, now and in the future, and, then, an analysis of the solutions is going to be done, creating a small guide of design. Firstly, is going to be defined what the modern industry is and then, and using that definition, the needs of the new industry are going to be defined. Secondly, different examples of modern industrial buildings will be analyzed taking into account the needs of the industry previously defined. This project could help anyone to understand better the importance of the buildings in the new industry and how are them changing because the evolution of the containers is, at least, the evolution of the industry.

Contribution à l'étude de la croissance de la fougère aquatique Salvinia molesta (Mitchell), Salviniaceae

The growth of the primary and the tertiary forms of the water fern Salvinia molesta was studied during 60 days in 0.06 m2 glass containers containing fresh water. The growth of this plant as a function of time is exponential. The two forms have growth rates statistically identical. The main daily growth rate, expressed in number of leaves, is equal to 6.40% per day for primary forms and 5.90% per day for tertiary form, with doubling time of 10.78 + 1.08 days and 11.64 + 0.15 days.

Reproduction et fécondité du machoiron Chrysichthys nigrodigitatus en élevage

Different rearing facilities (concrete tanks, pens and ponds) were tested for suitability as spawning environments. The concrete tanks and the pens in the lagoon gave the best results as to the number of spawns obtained. Of the three types of spawning devices tested, containers with a 150 mm opening at one of the two ends were preferably used by the fish. The brooders in the spawning facilities spontaneously entered the spawning containers to deposit their eggs without external human intervention. Actual fecundity estimates ranged from 9805 to 40597.

Avaliação ergonômica do processo de separação de materiais recicláveis utilizando um sistema modular estudo de caso em uma cooperativa de catadores do Estado do Rio de Janeiro.

O setor de separação (triagem) de materiais recicláveis de uma cooperativa localizada no estado do Rio de Janeiro foi o objeto deste estudo que teve como objetivo realizar uma avaliação ergonômica do processo de separação de resíduos recicláveis, executado por catadoras, utilizando um sistema modular. Os procedimentos metodológicos consistiram em pesquisa bibliográfica com levantamento do estado da arte, observações de campo utilizando a Análise Ergonômica do Trabalho (AET) e modelos esquemáticos da engenharia de métodos, e a realização de dois experimentos (posto-rampa e posto-bancada), utilizando a estratégia para montagem de ciclogramas proposta na Análise por Decomposição em Etapas (ADE). As análises obtidas através dos resultados de duas situações permitiram constatar que o processo atual de separação na rampa é deficitário, demorado e cansativo, deixa os catadores com dores nas costas e na coluna, além de existirem muitas perdas de tempo por transporte de materiais não agregando valor aos produtos, por conta da distância em que ficam os recipientes para o acondicionamento do material separado. O módulo bancada indicou ser a melhor alternativa para o arranjo físico da separação, encurtando as distâncias percorridas, suprimindo algumas movimentações do corpo (rotações e flexões de tronco), reduzindo os riscos de lesão na coluna vertebral. Diferente do arranjo físico atualmente adotado, o posto-bancada possibilita reduzir a duração média do ciclo e a frequência das Atividades Extra Ciclo (AECs). As recomendações para a melhoria da atividade na organização estudada visam preservar a saúde e elevar a produtividade. Elas foram elaboradas, considerando o arranjo físico, método de trabalho e qualificação dos trabalhadores.

Transfering pike to Lancaster Canal, March 1950

Two fishermen transfering pike using metal containers to the Lancaster Canal, North West of England, UK. This photo is part of a Photo Album that includes pictures from 1935 to 1954.