Optimum Design of Bridge Abutments under Seismic Conditions: Reliability-Based Approach

The paper focuses on the reliability-based design optimization of gravity wall bridge abutments when subjected to active condition during earthquakes. An analytical study considering the effect of uncertainties in the seismic analysis of bridge abutments is presented. Planar failure surface has been considered in conjunction with the pseudostatic limit equilibrium method for the calculation of the seismic active earth pressure. Analysis is conducted to evaluate the external stability of bridge abutments when subjected to earthquake loads. Reliability analysis is used to estimate the probability of failure in three modes of failure viz. sliding failure of the wall on its base, overturning failure about its toe (or eccentricity failure of the resultant force) and bearing failure of foundation soil below the base of wall. The properties of backfill and foundation soil below the base of abutment are treated as random variables. In addition, the uncertainties associated with characteristics of earthquake ground motions such as horizontal seismic acceleration and shear wave velocity propagating through backfill soil are considered. The optimum proportions of the abutment needed to maintain the stability are obtained against three modes of failure by targeting various component and system reliability indices. Studies have also been made to study the influence of various parameters on the seismic stability.

Multi-Tone Testing of Linear and Nonlinear Analog Circuits using Polynomial Coefficients

A method of testing for parametric faults of analog circuits based on a polynomial representation of fault-free function of the circuit is presented. The response of the circuit under test (CUT) is estimated as a polynomial in the applied input voltage at relevant frequencies in addition to DC. Classification or Cur is based on a comparison of the estimated polynomial coefficients with those of the fault free circuit. This testing method requires no design for test hardware as might be added to the circuit fly some other methods. The proposed method is illustrated for a benchmark elliptic filter. It is shown to uncover several parametric faults causing deviations as small as 5% from the nominal values.

Analysis of Energy Quantization Effects on Single-Electron Transistor Circuits

In this paper, the effects of energy quantization on different single-electron transistor (SET) circuits (logic inverter, current-biased circuits, and hybrid MOS-SET circuits) are analyzed through analytical modeling and Monte Carlo simulations. It is shown that energy quantizationmainly increases the Coulomb blockade area and Coulomb blockade oscillation periodicity, and thus, affects the SET circuit performance. A new model for the noise margin of the SET inverter is proposed, which includes the energy quantization effects. Using the noise margin as a metric, the robustness of the SET inverter is studied against the effects of energy quantization. An analytical expression is developed, which explicitly defines the maximum energy quantization (termed as ``quantization threshold'') that an SET inverter can withstand before its noise margin falls below a specified tolerance level. The effects of energy quantization are further studiedfor the current-biased negative differential resistance (NDR) circuitand hybrid SETMOS circuit. A new model for the conductance of NDR characteristics is also formulated that explains the energy quantization effects.

Vibration characteristics and damage detection in a suspension bridge

Suspension bridges are flexible and vibration sensitive structures that exhibit complex and multi-modal vibration. Due to this, the usual vibration based methods could face a challenge when used for damage detection in these structures. This paper develops and applies a mode shape component specific damage index (DI) to detect and locate damage in a suspension bridge with pre-tensioned cables. This is important as suspension bridges are large structures and damage in them during their long service lives could easily go un-noticed. The capability of the proposed vibration based DI is demonstrated through its application to detect and locate single and multiple damages with varied locations and severity in the cables of the suspension bridge. The outcome of this research will enhance the safety and performance of these bridges which play an important role in the transport network.

A simple analog controller for single-phase half-bridge rectifier and its application to transformerless UPS

A simple, low-cost, constant frequency, analog controller is proposed for the front-end half-bridge rectifier of a single-phase transformerless UPS system to maintain near unity power factor at the input and zero dc-offset voltage at the output. The controller generates the required gating pulses by comparing the input current with a periodic, bipolar, linear carrier without sensing the input voltage. Two voltage controllers and a single integrator with reset are used to generate the required carrier. All the necessary control operations can be performed without using any PLL, multiplier and/or divider. The controller can be fabricated as a single integrated circuit. The control concept is validated through simulation and also experimentally on an 800W half-bridge rectifier. Experimental results are presented for ac-dc application, and also for ac-dc-ac UPS application with both sinusoidal and nonlinear loads. The simulation and experimental results agree well.

On the performance analysis of a class of neuron circuits

A new performance metric, Peak-Error Ratio (PER) has been presented to benchmark the performance of a class of neuron circuits to realize neuron activation function (NAF) and its derivative (DNAF). Neuron circuits, biased in subthreshold region, based on the asymmetric cross-coupled differential pair configuration and conventional configuration of applying small external offset voltage at the input have been compared on the basis of PER. It is shown that the technique of using transistor asymmetry in a cross-coupled differential pair performs on-par with that of applying external offset voltage. The neuron circuits have been experimentally prototyped and characterized as a proof of concept on the 1.5 mu m AMI technology.

On the performance analysis of a class of neuron circuits

A new performance metric, Peak-Error Ratio (PER) has been presented to benchmark the performance of a class of neuron circuits to realize neuron activation function (NAF) and its derivative (DNAF). Neuron circuits, biased in subthreshold region, based on the asymmetric cross-coupled differential pair configuration and conventional configuration of applying small external offset voltage at the input have been compared on the basis of PER. It is shown that the technique of using transistor asymmetry in a cross-coupled differential pair performs on-par with that of applying external offset voltage. The neuron circuits have been experimentally prototyped and characterized as a proof of concept on the 1.5 mu m AMI technology.

Language and the Circuits of Power in a Merging Multinational Corporation

We argue in this paper that corporate language policies have significant power implications that are easily overlooked. By drawing on previous work on power in organizations (Clegg, 1989), we examine the complex power implications of language policy decisions by looking at three levels of analysis: episodic social interaction, identity/subjectivity construction, and reconstruction of structures of domination. In our empirical analysis, we focus on the power implications of the choice of Swedish as the corporate language in the case of the recent banking sector merger between the Finnish Merita and the Swedish Nordbanken. Our findings show how language skills become empowering or disempowering resources in organizational communication, how these skills are associated with professional competence, and how this leads to the creation of new social networks. The case also illustrates how language skills are an essential element in the construction of international confrontation, lead to a construction of superiority and inferiority, and also reproduce post-colonial identities in the merging bank. Finally, we also point out how such policies ultimately lead to the reification of post-colonial and neo-colonial structures of domination in multinational corporations.

Language and the circuits of power in a merging multinational corporation

We argue in this paper that corporate language policies have significant power implications that are easily overlooked. By drawing on previous work on power in organizations (Clegg, 1989), we examine the complex power implications of language policy decisions by looking at three levels of analysis: episodic social interaction, identity/subjectivity construction, and reconstruction of structures of domination. In our empirical analysis, we focus on the power implications of the choice of Swedish as the corporate language in the case of the recent banking sector merger between the Finnish Merita and the Swedish Nordbanken. Our findings show how language skills become empowering or disempowering resources in organizational communication, how these skills are associated with professional competence, and how this leads to the creation of new social networks. The case also illustrates how language skills are an essential element in the construction of international confrontation, lead to a construction of superiority and inferiority, and also reproduce post-colonial identities in the merging bank. Finally, we also point out how such policies ultimately lead to the reification of post-colonial and neo-colonial structures of domination in multinational corporations.

Low Power continuous time common mode sensing for common mode feedback circuits

Continuous common mode feedback (CMFB) circuits having high input impedance and low distortion are proposed. The proposed circuits are characterized for 0.18 mu m CMOS process with 1.8 V supply. Simulation results indicate that the proposed common mode detector consumes no standby power and CMFB circuit consumes 27-34% less power than previous high swing CMFB circuits.

Ratio transformer bridge for the measurement of dielectric constant of lossy liquids

A three-terminal capacitance bridge is developed for the measurement of the dielectric constant of lossy liquids. Using this modified ratio transformer bridge, the capacitance shunted by a resistance as low as 50 Omega is measured at 10 kHz. The capacitance error associated with the inductance of the connecting wire is compensated using the novel method of introducing an additional transformer to the existing ratio transformer bridge. Other sources of capacitance errors, such as the non-zero output impedence of the ratio transformer and the shield capacitances of the cables, are discussed.

Al/SiC carriers for microwave integrated circuits by a new technique of pressureless infiltration

Materials with high thermal conductivity and thermal expansion coefficient matching with that of Si or GaAs are being used for packaging high density microcircuits due to their ability of faster heat dissipation. Al/SiC is gaining wide acceptance as electronic packaging material due to the fact that its thermal expansion coefficient can be tailored to match with that of Si or GaAs by varying the Al:SiC ratio while maintaining the thermal conductivity more or less the same. In the present work, Al/SiC microwave integrated circuit (MIC) carriers have been fabricated by pressureless infiltration of Al-alloy into porous SiC preforms in air. This new technique provides a cheaper alternative to pressure infiltration or pressureless infiltration in nitrogen in producing Al/SiC composites for electronic packaging applications. Al-alloy/65vol% SiC composite exhibited a coefficient of thermal expansion of 7 x 10(-6) K-1 (25 degrees C-100 degrees C) and a thermal conductivity of 147 Wm(-1) K-1 at 30 degrees C. The hysteresis observed in thermal expansion coefficient of the composite in the temperature range 100 degrees C-400 degrees C has been attributed to the presence of thermal residual stresses in the composite. Thermal diffusivity of the composite measured over the temperature range from 30 degrees C to 400 degrees C showed a 55% decrease in thermal diffusivity with temperature. Such a large decrease in thermal diffusivity with temperature could be due to the presence of micropores, microcracks, and decohesion of the Al/SiC interfaces in the microstructure (all formed during cooling from the processing temperature). The carrier showed satisfactory performance after integrating it into a MIC.

Impact of energy quantisation in single electron transistor island on hybrid complementary metal oxide semiconductor-single electron transistor integrated circuits

For the first time, the impact of energy quantisation in single electron transistor (SET) island on the performance of hybrid complementary metal oxide semiconductor (CMOS)-SET transistor circuits has been studied. It has been shown through simple analytical models that energy quantisation primarily increases the Coulomb Blockade area and Coulomb Blockade oscillation periodicity of the SET device and thus influences the performance of hybrid CMOS-SET circuits. A novel computer aided design (CAD) framework has been developed for hybrid CMOS-SET co-simulation, which uses Monte Carlo (MC) simulator for SET devices along with conventional SPICE for metal oxide semiconductor devices. Using this co-simulation framework, the effects of energy quantisation have been studied for some hybrid circuits, namely, SETMOS, multiband voltage filter and multiple valued logic circuits. Although energy quantisation immensely deteriorates the performance of the hybrid circuits, it has been shown that the performance degradation because of energy quantisation can be compensated by properly tuning the bias current of the current-biased SET devices within the hybrid CMOS-SET circuits. Although this study is primarily done by exhaustive MC simulation, effort has also been put to develop first-order compact model for SET that includes energy quantisation effects. Finally, it has been demonstrated that one can predict the SET behaviour under energy quantisation with reasonable accuracy by slightly modifying the existing SET compact models that are valid for metallic devices having continuous energy states.

A Hybrid Multilevel Inverter Topology for an Open-End Winding Induction-Motor Drive Using Two-Level Inverters in Series With a Capacitor-Fed H-Bridge Cell

In this paper, a new five-level inverter topology for open-end winding induction-motor (IM) drive is proposed. The open-end winding IM is fed from one end with a two-level inverter in series with a capacitor-fed H-bridge cell, while the other end is connected to a conventional two-level inverter. The combined inverter system produces voltage space-vector locations identical to that of a conventional five-level inverter. A total of 2744 space-vector combinations are distributed over 61 space-vector locations in the proposed scheme. With such a high number of switching state redundancies, it is possible to balance the H-bridge capacitor voltages under all operating conditions including overmodulation region. In addition to that, the proposed topology eliminates 18 clamping diodes having different voltage ratings compared with the neutral point clamped inverter. On the other hand, it requires only one capacitor bank per phase, whereas the flying-capacitor scheme for a five-level topology requires more than one capacitor bank per phase. The proposed inverter topology can be operated as a three-level inverter for full modulation range, in case of any switch failure in the capacitor-fed H-bridge cell. This will increase the reliability of the system. The proposed scheme is experimentally verified on a four-pole 5-hp IM drive.

Bridging East and West : The Establishment of the International Institute for Applied Systems Analysis (IIASA) in the United States Foreign Policy of Bridge Building, 1964-1972.

The dissertation examines the foreign policies of the United States through the prism of science and technology. In the focal point of scrutiny is the policy establishing the International Institute for Applied Systems Analysis (IIASA) and the development of the multilateral part of bridge building in American foreign policy during the 1960s and early 1970s. After a long and arduous negotiation process, the institute was finally established by twelve national member organizations from the following countries: Bulgaria, Canada, Czechoslovakia, Federal Republic of Germany (FRG), France, German Democratic Republic (GDR), Great Britain, Italy, Japan, Poland, Soviet Union and United States; a few years later Sweden, Finland and the Netherlands also joined. It is said that the goal of the institute was to bring together researchers from East and West to solve pertinent problems caused by the modernization process experienced in industrialized world. It originates from President Lyndon B. Johnson s bridge building policies that were launched in 1964, and was set in a well-contested and crowded domain of other international organizations of environmental and social planning. Since the distinct need for yet another organization was not evident, the process of negotiations in this multinational environment enlightens the foreign policy ambitions of the United States on the road to the Cold War détente. The study places this project within its political era, and juxtaposes it with other international organizations, especially that of the OECD, ECE and NATO. Conventionally, Lyndon Johnson s bridge building policies have been seen as a means to normalize its international relations bilaterally with different East European countries, and the multilateral dimension of the policy has been ignored. This is why IIASA s establishment process in this multilateral environment brings forth new information on US foreign policy goals, the means to achieve these goals, as well as its relations to other advanced industrialized societies before the time of détente, during the 1960s and early 1970s. Furthermore, the substance of the institute applied systems analysis illuminates the differences between European and American methodological thinking in social planning. Systems analysis is closely associated with (American) science and technology policies of the 1960s, especially in its military administrative applications, thus analysis within the foreign policy environment of the United States proved particularly fruitful. In the 1960s the institutional structures of European continent with faltering, and the growing tendencies of integration were in flux. One example of this was the long, drawn-out process of British membership in the EEC, another is de Gaulle s withdrawal from NATO s military-political cooperation. On the other hand, however, economic cooperation in Europe between East and West, and especially with the Soviet Union was expanding rapidly. This American initiative to form a new institutional actor has to be seen in that structural context, showing that bridge building was needed not only to the East, but also to the West. The narrative amounts to an analysis of how the United States managed both cooperation and conflict in its hegemonic aspirations in the emerging modern world, and how it used its special relationship with the United Kingdom to achieve its goals. The research is based on the archives of the United States, Great Britain, Sweden, Finland, and IIASA. The primary sources have been complemented with both contemporary and present day research literature, periodicals, and interviews.