Mechanism of enhanced corrosion of alumina graphite refractories near slag/metal interface

All refractories show enhanced corrosion near the slag/metal interface due to Marangoni and convective flows. However, in the case of oxide refractories containing graphite flakes, corrosion is severe due to periodic oscillations in the contact angle at the slag/metal interface, resulting in cyclic dissolution of oxide and graphite into the slag and metal, respectively. Alumina--graphite (AG) refractories should be used only where they are not in simultaneous contact with slag (flux) and low carbon steel.

Hybrid Bayesian Classifier for Improved Classification Accuracy

The widely used Bayesian classifier is based on the assumption of equal prior probabilities for all the classes. However, inclusion of equal prior probabilities may not guarantee high classification accuracy for the individual classes. Here, we propose a novel technique-Hybrid Bayesian Classifier (HBC)-where the class prior probabilities are determined by unmixing a supplemental low spatial-high spectral resolution multispectral (MS) data that are assigned to every pixel in a high spatial-low spectral resolution MS data in Bayesian classification. This is demonstrated with two separate experiments-first, class abundances are estimated per pixel by unmixing Moderate Resolution Imaging Spectroradiometer data to be used as prior probabilities, while posterior probabilities are determined from the training data obtained from ground. These have been used for classifying the Indian Remote Sensing Satellite LISS-III MS data through Bayesian classifier. In the second experiment, abundances obtained by unmixing Landsat Enhanced Thematic Mapper Plus are used as priors, and posterior probabilities are determined from the ground data to classify IKONOS MS images through Bayesian classifier. The results indicated that HBC systematically exploited the information from two image sources, improving the overall accuracy of LISS-III MS classification by 6% and IKONOS MS classification by 9%. Inclusion of prior probabilities increased the average producer's and user's accuracies by 5.5% and 6.5% in case of LISS-III MS with six classes and 12.5% and 5.4% in IKONOS MS for five classes considered.

On the k(1)(-1) scaling in sink-flow turbulent boundary layers

Scaling of the streamwise velocity spectrum phi(11)(k(1)) in the so-called sink-flow turbulent boundary layer is investigated in this work. The present experiments show strong evidence for the k(1)(-1) scaling i.e. phi(11)(k(1)) = Lambda(1)U(tau)(2)k(1)(-1), where k(1)(-1) is the streamwise wavenumber and U-tau is the friction velocity. Interestingly, this k(1)(-1) scaling is observed much farther from the wall and at much lower flow Reynolds number (both differing by almost an order of magnitude) than what the expectations from experiments on a zero-pressure-gradient turbulent boundary layer flow would suggest. Furthermore, the coefficient A(1) in the present sink-flow data is seen to be non-universal, i.e. A(1) varies with height from the wall; the scaling exponent -1 remains universal. Logarithmic variation of the so-called longitudinal structure function, which is the physical-space counterpart of spectral k(1)(-1) scaling, is also seen to be non-universal, consistent with the non-universality of A(1). These observations are to be contrasted with the universal value of A(1) (along with the universal scaling exponent of 1) reported in the literature on zero-pressure-gradient turbulent boundary layers. Theoretical arguments based on dimensional analysis indicate that the presence of a streamwise pressure gradient in sink-flow turbulent boundary layers makes the coefficient A(1) non-universal while leaving the scaling exponent -1 unaffected. This effect of the pressure gradient on the streamwise spectra, as discussed in the present study (experiments as well as theory), is consistent with other recent studies in the literature that are focused on the structural aspects of turbulent boundary layer flows in pressure gradients (Harun etal., J. Flui(d) Mech., vol. 715, 2013, pp. 477-498); the present paper establishes the link between these two. The variability of A(1) accommodated in the present framework serves to clarify the ideas of universality of the k(1)(-1) scaling.

Anatomy of Higgs mass in supersymmetric inverse seesaw models

We compute the one loop corrections to the CP-even Higgs mass matrix in the supersymmetric inverse seesaw model to single out the different cases where the radiative corrections from the neutrino sector could become important. It is found that there could be a significant enhancement in the Higgs mass even for Dirac neutrino masses of O(30) GeV if the left-handed sneutrino soft mass is comparable or larger than the right-handed neutrino mass. In the case where right-handed neutrino masses are significantly larger than the supersymmetry breaking scale, the corrections can utmost account to an upward shift of 3 GeV. For very heavy multi TeV sneutrinos, the corrections replicate the stop corrections at 1-loop. We further show that general gauge mediation with inverse seesaw model naturally accommodates a 125 GeV Higgs with TeV scale stops. (C) 2014 The Authors. Published by Elsevier B.V.

Effect of a mesh on boundary layer transitions induced by free-stream turbulence and an isolated roughness element

Streamwise streaks, their lift-up and streak instability are integral to the bypass transition process. An experimental study has been carried out to find the effect of a mesh placed normal to the flow and at different wall-normal locations in the late stages of two transitional flows induced by free-stream turbulence (FST) and an isolated roughness element. The mesh causes an approximately 30% reduction in the free-stream velocity, and mild acceleration, irrespective of its wall-normal location. Interestingly, when located near the wall, the mesh suppresses several transitional events leading to transition delay over a large downstream distance. The transition delay is found to be mainly caused by suppression of the lift-up of the high-shear layer and its distortion, along with modification of the spanwise streaky structure to an orderly one. However, with the mesh well away from the wall, the lifted-up shear layer remains largely unaffected, and the downstream boundary layer velocity profile develops an overshoot which is found to follow a plane mixing layer type profile up to the free stream. Reynolds stresses, and the size and strength of vortices increase in this mixing layer region. This high-intensity disturbance can possibly enhance transition of the accelerated flow far downstream, although a reduction in streamwise turbulence intensity occurs over a short distance downstream of the mesh. However, the shape of the large-scale streamwise structure in the wall-normal plane is found to be more or less the same as that without the mesh.

Fluoranthene derivatives as blue fluorescent materials for non-doped organic light-emitting diodes

In this study, we report synthesis of symmetrically and non-symmetrically functionalized fluoranthene-based blue fluorescent molecular materials for non-doped electroluminescent devices. The solid state structure of these fluorophores has been established by single crystal X-ray diffraction analysis. Furthermore, a detailed experimental and theoretical study has been performed to understand the effect of substitution of symmetric and non-symmetric functional groups on optical, thermal and electrochemical properties of fluoranthene. These materials exhibit a deep blue emission and high PLQY in solution and solid state. The vacuum deposited, non-doped electroluminescent devices with the device structure ITO/NPD (15 nm)/CBP (15 nm)/EML (40 nm)/TPBI (30 nm)/LiF (1 nm)/Al were fabricated and characterized. A systematic shift in the peak position of EL emission was observed from sky blue to bluish-green with EL maxima from 477 nm to 490 nm due to different functional groups on the periphery of fluoranthene. In addition, a high luminance of >= 2000 cd m(-2) and encouraging external quantum efficiency (EQE) of 1.1-1.4% were achieved. A correlation of the molecular structure with device performance has been established.

Solution processed Cu2SnS3 thin films for visible and infrared photodetector applications

The Cu2SnS3 thin films were deposited using an economic, solution processible, spin coating technique. The films were found to possess a tetragonal crystal structure using X-ray diffraction. The film morphology and the particle size were determined using scanning electron microscopy. The various planes in the crystal were observed using transmission electron microscopy. The optimum band gap of 1.23 eV and a high absorption coefficient of 104 cm-1 corroborate its application as a photoactive material. The visible and infrared (IR) photo response was studied for various illumination intensities. The current increased by one order from a dark current of 0.31 mu A to a current of 1.78 mu A at 1.05 suns and 8.7 mu A under 477.7 mW/cm(2) IR illumination intensity, at 3 V applied bias. The responsivity, sensitivity, external quantum efficiency and specific detectivity were found to be 10.93 mA/W, 5.74, 2.47% and 3.47 x 10(10) Jones respectively at 1.05 suns and 16.32 mA/W, 27.16, 2.53% and 5.10 x 10(10) Jones respectively at 477.7 mW/cm(2) IR illumination. The transient photoresponse was measured both for visible and IR illuminations. (C) 2016 Author(s).

Pressure Drop of Bubbly Two-Phase Flow in a Square Channel at Reduced Gravity

A new set of experimental pressure drop data, collected aboard the Russian IL-76MDK, is reported for bubbly airwater two-phase flow in a square channel with a cross-sectional area of 12x 12mm(2). The present data are compared to several frequently used empirical models, e.g. homogeneous model, Lockhart-Martinelli-Chisholm correlation and Friedel's model. It is shown that the predictions of the models mentioned above are generally not satisfied. A new homogeneous model is developed based on the analysis of the characteristics of bubbly two-phase flow at reduced gravity. It is tested with the present data and other data collected by other researchers in circular pipes. Some questions related to the present model are also discussed. (C) 2002 COSPAR. Published by Elsevier Science Ltd. All rights reserved.

Incremento de la productividad de frijol (Phaseolus vulgaris L.) a nivel de finca mediante la inoculación con Rhizobium leguminosarum bv. phaseoli

El efecto de una mezcla de tres cepas de Rhizobium leguminosarum biovar phaseoll (CIAT-613, CR-477 y KIM-5) relacionado con los factores limitantes del suelo (P, Ca, Cu, y Zn) sobre la simbiosis en tres variedades de Phaseolus vulgaris L. (DOR-364, ESTELI-90B y FIEVOLUCION-84) fue estudiado en un suelo Molisol y un Aluvial en las localidades de San Diego (Nandaime) y San Lorenzo (La Trinidad, Estelí), respectivamente, bajo condiciones de labranza convencional para ambas localidades. En la localidad de San Lorenzo se trabajó con las variedades DOR-364 y EST-908 con la corrección del cobre (factor A) y el zinc (factor 8), mientras que en la localidad de San Diego, el trabajo se realizó con las variedades DOR-364 y REVOLUCION-84 y la corrección del calcio (factor A) y el fósforo (factor 8), Ambos estudios se llevaron a cabo en época de postrera de 1994. En los dos ensayos la inoculación se hizo directamente a la semilla. Los tratamientos a evaluar fueron los siguientes: Alto nitrógeno, bajo nitrógeno como testigos (sin inocular), mezcla de inoculantes con (-A,-B), (+A,-B), (-A,+B), y (+A,+B) para un total de seis tratamientos por cada variedad. El diseño usado fue de bloques completos al azar (B.C.A). Las variables evaluadas fueron: Número y peso seco de nódulos, peso de materia seca de la planta en R6, peso de mil granos y rendimiento de grano en R9. Los datos se procesaron usando análisis de varianza (ANDEVA) y se utilizó la prueba de rangos múltiples de DUNCAN (P ≤ 0,05). Se observó a nivel general en ambos experimentos que la variedad introducida mostró un mayor rendimiento y que el mejor rendimiento de grano se obtuvo con el tratamiento en el que se usó alta dosis de nitrógeno y sin inocular. Por otro lado el rendimiento de frijol fue afectado negativamente por las aplicaciones de zinc en el caso del experimento en San Lorenzo. Para la localidad de San Diego se obtuvo respuesta positiva a las aplicaciones de fósforo junto con la mezcla de inoculantes usados. En los dos experimentos no se encontró respuesta significativa con el uso de la mezcla de inoculantes relacionados con los elementos limitantes del suelo comparado con los testigos.

Incremento de la productividad de frijol común (Phaseolus vulgaris L.) a nivel de finca mediante la inoculación con Rhizobium leguminosarum bv. Phaseoli

En el presente trabajo experimental se evaluó la respuesta a la inoculación de dos variedades de frijol común Phaseolus vulgaris L. con el objetivo de incrementar los rendimientos unitarios. Las variedades fueron DOR-364 y EST-90B, inoculadas con tres cepas de Rhizobium leguminosarum biovar phaseoli (CR-477, KIM-5 y CIAT-613) bajo condiciones de labranza convencional en la localidad de San Lorenzo, ubicada a 1O km del municipio de La Trinidad en el departamento de Estelí. Este estudio se realizó en dos etapas, postrera (1993) y primera (1994). En la primera etapa experimental se aplicó el inoculante al suelo al momento de la siembra y en la segunda etapa la inoculación se hizo a la semilla. En la primera etapa se utilizaron dos inoculantes (KIM-5 y CR-477) comparados con dos testigos sin inocular, con bajo nitrógeno (20 kg/ha de N) y el testigo sin inocular y el otro con alto nitrógeno (90 kg/ha de N en forma fraccionada). En la segunda etapa experimental, los tratamientos inoculados (KIM-5, CR-477, CIAT-613 y mezcla de las tres cepas), se compararon siempre con dos testigos sin inocular, uno sin nitrógeno y otro con alto nitrógeno (50 kg/ha de N). El diseño utilizado para ambas fases fue el de parcelas divididas (DPD). En el primer ensayo las variables medidas fueron número y peso seco de nódulos, peso seco de la parte aérea en las etapas R6 y R8 así como el rendimiento de grano. En el segundo ensayo se hicieron las mismas mediciones con la excepción del peso seco de la parte aérea en la etapa R8 del cultivo. En el primer experimento hubo respuesta significativa a la inoculación con las cepas evaluadas en la etapa R8 del cultivo, mientras que en el segundo experimento no hubo respuesta significativa en el peso seco de la parte aérea en esta etapa, en donde el mejor tratamiento fue el fertilizado con alto nitrógeno en el primer ensayo. En la primera fase del estudio, el rendimiento aunque no significativo, se vio favorecido con la fertilización nitrogenada para ambas variedades. En el segundo experimento se observó diferencias significativas en el rendimiento de grano, obteniéndose los más altos rendimientos con el tratamiento CR-477 en ambas variedades. En este estudio los tratamientos fertilizados presentaron menor rendimiento comparado con los tratamientos sin nitrógeno.

碱金属在[110]单轴应力下的理论强度

<正> 我们知道,晶须的强度远远大于大晶体的强度,很可能接近于理想晶体的理论强度.而晶须的轴线则通常平行于晶体的三个主要方向[100],[110]或[111]。因此当计算理想晶体在单轴应力下的理论强度时,也必须考虑不同的应力方向.七十年代,Milstein等人利用Morse势和Born稳定性判据计算了立方晶体分别在[100],[110]和[111]单轴应力下的理论强度.由于有心力近似受到Cauchy关系的限制,我们在文献

地震应力波的传播与岩石的动态响应

本文用 Split-Hopkinson 压力杆装置研究了应力波通过破裂岩石试件的衰减现象。给出了灰砂岩、石灰岩两种岩石动态的破裂强度与应力应变关系.结合受应力作用的岩样切片的微观观察,对应力裂纹、裂纹的动态分叉现象进行了分析讨论.

Distribution, stability, bifurcations and catastrophe of steady rotation of a symmetrical heavy gyroscope with viscous-liquid-filled cavity

The number, the angles of orientation and the stability in Rumyantsev Movchan's sense of oblique steady rotations of a symmetric heavy gyroscope with a cavity completely filled with a uniform viscous liquid, possessing a fixed point 0 on its symmetric axis. are given for various values of the parameters. By taking the square of the upright component of the angular momentum M2 as a control parameter, three types of bifurcation diagrams of the steady rotations, two types of jumps and two kinds of local catastrophes, one being the symmetric reduced cusp type and the other being of the symmetric reduced butterfly type, are obtained. By taking account of the M2-damping owing to the moment of unavoidable faint friction, two different modes for the gyroscope, initially in a stable quasi-steady upright rotation with a nutation angle theta(s) equal to zero, to topple over are found.

[Discurso do Deputado Valério Magalhães : Sessão da Câmara dos Deputados de 26 de setembro de 1963]

Críticas aos movimentos pelo retorno da Capital para o Rio de Janeiro, em que menciona o Deputado Amaral Neto como autor intelectual.