DDES of a supersonic coaxial helium jet

The mixing of a light gas in a scramjet combustion chamber is replicated through the simulation of a supersonic coaxial helium jet. Sensitivities of the RANS method to model constants is presented and the DDES method is employed to try and alleviate this modelling weakness. A significant delay in the shear layer transition is found to occur in the DDES simulation and it is suggested this may be due to the absence of inlet turbulence. The influence of the introduction of inflow turbulence is investigated and computational results are compared to experimental data. The influence of model constants on the DDES results are presented. © 2012 by Peter Cocks.

Effect of laser heating temperature on coating characteristics of Stellite 6 deposited by cold spray

Laser-assisted cold spray (LCS) is a new coating and fabrication process which combines some advantages of CS: solid-state deposition, retain their initial composition and high build rate with the ability to deposit materials which are either difficult or impossible to deposit using cold spray alone. Stellite 6 powder is deposited on medium carbon steels by LCS using N 2 as carrier gas pressure. The topography, cross section thickness, structure of the coatings is examined by SEM, optical microscopy, EDX. The results show that thickness and fluctuation of coating are improved with increased deposition site temperature. Porosity of coating is affected by N 2 and deposition site temperature. In this paper, it presents optimal coating using N 2 at a pressure of 3 MPa and temperature of 450°C and deposition site temperature of 1100°C.

Electroluminescence in Single Layer MoS2

We detect electroluminescence in single layer molybdenum disulphide (MoS2) field-effect transistors built on transparent glass substrates. By comparing absorption, photoluminescence, and electroluminescence of the same MoS2 layer, we find that they all involve the same excited state at 1.8eV. The electroluminescence has pronounced threshold behavior and is localized at the contacts. The results show that single layer MoS2, a direct band gap semiconductor, is promising for novel optoelectronic devices, such as 2-dimensional light detectors and emitters.

Theory of huge tunneling magnetoresistance in graphene

We investigate theoretically the spin-independent tunneling magnetoresistance effect in a graphene monolayer modulated by two parallel ferromagnets deposited on a dielectric layer. For the parallel magnetization configuration, Klein tunneling can be observed in the transmission spectrum but at specific oblique incident angles. For the antiparallel magnetization configuration, the transmission can be blocked by the magneticelectric barrier provided by the ferromagnets. Such a transmission discrepancy results in a tremendous magnetoresistance ratio and can be tuned by the inclusion of an electric barrier.

Orbital magnetization in semiconductors

National Natural Science Foundation of China 60821061 60776061 10604010 60776063

Dependence of intrinsic defects in ZnO films on oxygen fraction studied by positron annihilation

Defects in ZnO films grown by radio-frequency reactive magnetron sputtering under variable ratios between oxygen and argon gas have been investigated by using the monoenergetic positron beam technique. The dominate intrinsic defects in these ZnO samples are O vacancies (V-O) and Zn interstitials (Zn-i) when the oxygen fraction in the O-2/Ar feed gas does not exceed 70% in the processing chamber. On the other hand, zinc vacancies are preponderant in the ZnO Elms fabricated in richer oxygen environment. The concentration of zinc vacancies increases with the increasing (2) fraction. For the oxygen fraction 85%, the number of zinc vacancies that could trap positrons will be smaller. It is speculated that some unknown defects could shield zinc vacancies. The concentration of zinc vacancies in the ZnO films varies with the oxygen fraction in the growth chamber, which is in agreement with the results of photoluminescence spectra.

Novel coupled multi-active region high power semiconductor lasers cascaded via tunnel junction

A novel semiconductor laser structure is put forward to resolve the major difficulties of high power laser diodes. In this structure, several active regions are cascaded by tunnel junctions to form a large optical cavity and to achieve super high efficiency. This structure can solve the problems of catastrophic optical damage of facet, thermal damage and poor light beam quality effectively. Low-pressure metalorganic chemical vapor deposition method is adopted to grow the novel semiconductor laser structures, which are composed of Si:GaAs/C:GaAs tunnel junctions, GaAs/InGaAs strain quantum well active regions. External differential quantum efficiency as high as 2.2 and light power output of 2.5 W per facet (under 2A drive current) are achieved from an uncoated novel laser device with three active regions.

Room temperature mobility above 2100 cm2/Vs in Al0.3Ga0.7N/AIN/GaN heterostructures grown on sapphire substrates by MOCVD

Al0.3Ga0.7N/AlN/GaN HEMT structures with significantly high mobility have been grown by metalorganic chemical vapor deposition (MOCVD) on sapphire substrates. At room temperature (RT) a Hall mobility of 2104 cm(2)/Vs and a two-dimensional electron gas (2DEG) density of 1.1x10(13) cm(-2) are achieved, corresponding to a sheet resistance of 277.8 Omega/sq. The elimination of V-shaped defects were observed on Al0.3Ga0.7N/AlN/GaN HEMT structures and correlated with the increase of 2DEG mobility. (c) 2006 WILEY-VCH Verlag GmbH & Co KGaA, Weinheim.

Influence of A-type Zeolite on Methane Hydrate Formation

The porous medium has an important effect on hydrate formation. In this paper, the formation process and the gas storage capacity of the methane hydrate were investigated with A-type zeolite and Sodium Dodecyl Sulfate (SDS) existing in the system. The results show that A-type zeolite can influence methane hydrate formation. At the temperature of 273.5 K and pressure of 8.3 MPa, the distilled water with A-type zeolite can form methane hydrate with gaseous methane in 12 hours. The formation process of the system with A-type zeolite was quite steady and the amount of A-type zeolite can influence the gas storage capacity significantly. The adding of A-type zeolite with 0.067 g.(g water)(-1) into 2 x 10(-3) g.g(-1) SDS-water solution can increase the gas storage capacity, and the maximum increase rate was 31%. Simultaneously the promotion effect on hydrate formation of 3A-type zeolite is much more obvious than that of 5A-type zeolite when the water adding amounts are 0.033 g.g(-1) and 0.067 g.g(-1) at the experimental conditions.

Observation of N-Shaped Negative Differential Resistance in GaAs-Based Modulation-Doped Field Effect Transistor with InAs Quantum Dots

N-shaped negative differential resistance (NDR) with a high peak-to-valley ratio (PVR) is observed in a GaAs-based modulation-doped field effect transistor (MODFET) with InAs quantum dots (QDs) in the barrier layer (QDFET) compared with a GaAs MODFET. The NDR is explained as the real-space transfer (RST) of high-mobility electrons in a channel into nearby barrier layers with low mobility, and the PVR is enhanced dramatically upon inserting the QD layer. It is also revealed that the QD layer traps holes and acts as a positively charged nano-floating gate after a brief optical illumination, while it acts as a negatively charged nano-floating gate and depletes the adjacent channel when charged by the electrons. The NDR suggests a promising application in memory or high-speed logic devices for the QDFET structure.

CFD study of a sudden-expanding coal combustor using Euler-Euler and Euler-Lagrange models

In this study, the Euler-Euler (E-E) and Euler-Lagrange (E-L) models designed for the same chemical mechanism of heterogeneous reactions were used to predict the performance of a typical sudden-expanding coal combustor. The results showed that the current E-E model underestimated the coal burnout rate because the particle temperature fluctuation on char combustion is not adequately considered. A comparison of the E-E and E-L simulations showed the underestimation of heterogeneous chemical reaction rates by the E-E model. (C) 2010 Elsevier Ltd. All rights reserved.

青藏高原青稞淀粉资源的评价

青稞（Hordeum vulgare L.var．nudum Hook．f.），即裸大麦，是兼食用、饲用和酿造于一体的作物，有着重要的利用价值。淀粉是青稞籽粒中含量最多、最重要的碳水化合物，淀粉含量、直支淀粉比将会直接影响淀粉的功能特性，进而影响淀粉的应用领域。我国青藏高原青稞的栽培和食用历史悠久，特色青稞资源极其丰富。目前关于青藏高原青稞淀粉特性的报道还不多见，筛选和培育特色淀粉青稞利于拓展青稞的应用领域, 从而提高其经济价值。 本研究以114份青藏高原青稞品种(系)为实验材料，通过SDS-PAGE对材料的胚乳淀粉颗粒结合蛋白（SGAPs）进行分离，确定各蛋白的分子量大小、组合类型和多态性等。然后按照国标法测试材料的籽粒总淀粉含量和直链淀粉含量，通过微型糊化粘度仪分析相应的淀粉糊化特性，最后使用显微镜观察比较了青稞的淀粉颗粒形态特征。主要结果如下： 1、114种青稞中共分离出20种不同的SGAP条带，条带分子量为35.00～112.39 KDa，分布频率为12.28～97.37%。材料含有的SGAPs条带数从10到14不等，超过一半的材料含11种SGAP条带。20种条带形成16种组合类型，其中西藏地区青稞包含所有16个组合类型，四川地区青稞包含其中12个组合类型。青藏高原青稞籽粒淀粉颗粒结合蛋白的差异很大，遗传多样性丰富。 2、114份青稞的总淀粉含量、直链淀粉含量、直支淀粉比、峰值粘度、糊化温度和峰值温度的变幅分别为51.26～66.70%、14.64～29.74%、0.17～0.42、194～1135BU、58.8～65.2℃和81.4～92.4℃，相应的平均值分别为59.82%、23.60%、0.31、722.30BU、62.1℃和88.8℃。群体在总淀粉含量、直链淀粉含量、直支淀粉比、峰值粘度、糊化温度和峰值温度上的分布具有明显的正态性；所有胚乳淀粉体的淀粉粒都呈复粒结构。对西藏和四川的材料进行了分组比较， 两地区的青稞在直链淀粉含量和直支淀粉比上的差异达到显著水平。 3、筛选出18份具有特殊淀粉特性的青稞品种，其中5份材料的总淀粉含量超过65%，包括NB63-1、NB67、甘孜白六棱、98221-1和NB63；3份材料的直链淀粉含量大于29%，包括藏青85、藏青3号和喜马拉6号；8份材料的直支淀粉比小于0.25，包括99033-6、春青稞、阿坝330、Jan-03、米麦114、396、NB63-1和92013；7份材料的糊化温度低于60℃，同时材料的峰值粘度大于1000BU,并且峰值温度低于90℃，包括足捉春、Jan-03、阿坝330、米麦114、春青稞、20003和阿青5号。 4、各淀粉特性间存在高度相关性。直链淀粉含量和直支淀粉比与糊化温度成极显著正相关，与峰值粘度成极显著负相关，与A型淀粉粒数量和大小呈负相关。不同SGAPs组合的品种之间，淀粉含量和淀粉糊化特性间差异均达显著水平。SGAP2、SGAP5、SGAP6和SGAP7可能对籽粒直链淀粉含量、直支淀粉比和糊化温度有正向效应；SGAP3、SGAP9∼SGAP20可能对峰值粘度有正向效应。 本研究对青藏高原青稞淀粉资源进行了较为全面的评价，对该区青稞淀粉特性有了系统的认识。研究筛选出的特殊青稞品种可作为青稞育种和青稞淀粉工业应用的潜在资源，淀粉特性差异巨大的众多青稞品种也为拓宽青稞应用领域提供了丰富的资源保障。本研究对部分SGAPs在性质上的鉴定和功能上的初步推断为青稞材料的筛选提供了指导，也为品质育种提供了理论参考。 Hulless barley (naked barley, Hordeum vulgare L.) is a short- season, early maturing crop with a wide range of adaptation. It has been attracting more and more attention due to its superior nutrition and extensive industrial applications. Starch is the main ingredient in hulless barley seeds which makes up 65 percent of hulless barley’s dry weight. The ratio of the amylose/amylopectin and the size, shape, distribution of starch granules can affect the physico-chemical and functional properties of starch, which may turn affect its utilizations. The Qinghai-Tibet Plateau, which is located in southwestern China, is a typical area of vertical agricultural ecosystem and one of the barley origin centers with abundant hulless barley resources. There are little reports about hulless barley in Qinghai-Tibet Plateau at present. To screen and cultivate some characteristic hulless barley can improve its value. An improved SDS-PAGE was used to identify SGAPs combination of 114 hulless barley varieties. Starch content (total starch and amylose starch) was determined according to the standard methods GB5006-85 and GB/T 15683 using PerkinElmer M341 Precision Automatic Polarimeter and UV spectrophotometer 755B respectively. The pasting properties were measured by BRABENDER Micrio Visco-Amylo- Graph 803201. The morphology of starch granules were observed and compared with Axioplan 2 Imaging light microscopy. The following were the results obtained: 1. There were 20 major SGAPs presented in 114 varieties, with the molecular weight ranged from 35.00 to 112.39 KDa, and the frequencies ranged from 12.28% to 97.37%. The number of SGAP bands in each accession varied from 10 to 14, more than half of the population had 11 bands. There were 16 distinct SGAP patterns in the 114 varieties, the Tibet hulless barley had all of the 16 types and the Sichuan hulless barley had 12 types. The results indicated the Qinghai-Tibet Plateau hulless barley had a polymorphism of the SGAPs. 2. The ranges of the total starch content, amylose content, Am/Ap, peak viscosity, pasting temperature and peak temperature of the 114 hulless barley were 51.26～66.70%,14.64～29.74%,0.17～0.42,194～1135BU,58.8～65.2 and 81.4℃～92.4, with an average of ℃59.82%, 23.60%, 0.31, 722.30BU, 62.1 and 88.8,℃℃ respectively. The distributions of the total starch content, amylose content, Am/Ap, peak viscosity, pasting temperature and peak temperature were visibly normal school. All of the amyloplasts in endosperm of varieties showed bimodal size distributions.The main starch properties of hulless barley from Tibet and Sichuan were separated and compared, the differences on amylose content and Am/Ap were obvious. 3. Eighteen accessions which had special starch properties were screened out. Five accessions with total starch content beyond 65%, including NB63-1, NB67, Ganzibailiuleng, 98221-1 and NB63; three accessions, Zangqing85, Zangqing3 and Ximala6, with the highest amylose content (>29%); five accessions with Am/Ap less than 0.25, including 99033-6, Chun Qingke, A Ba 330, Jan-03, Mi Mai114, 396, NB63-1 and 92013; seven accessions had a pasting temperature under 60, ℃meanwhile their peak viscosity beyond 1000BU and their peak temperature under 90℃，including Zu Cuochun, Jan-03, A Ba 330, Mi Mai 114, Chun Qingke, 20003 and A Qing 5. 4. There were high correlations between starch properties. Amylose content and Am/Ap were positively correlated to pasting temperature, negatively correlated to peak viscosity, negatively correlated to the number and granule size of A-type granule. Different SGAP combinations caused significant diversities in starch content and pasting properties. SGAP2, SGAP5, SGAP6 and SGAP7 may have positive effect on amylose content, Am/Ap and pasting temperature; SGAP3, SGAP9∼SGAP20 may have positive effect on peak viscosity. Our research made a comprehensive evaluation on the hulless barley starch from the Qinghai-Tibet Plateau, we can get a systemic understanding. Some special accessions were screened out can be used on the hulless barley breeding lines and industries utilization.The combination of the SGAPs may become a criterion to evaluate the hulless barley endosperm starch quality. Consequently, the results will be good information for further studies on the hulless barley.

CO selective oxidation in a microchannel reactor for PEM fuel cell

It is indispensable to remove CO at the level of less than 50ppm in H-2-rich feed gas for the proton exchange membrane (PEM) fuel cells. In this paper, catalyst with high activity and selectivity, and a microchannel reactor for CO preferential oxidation (PROX) have been developed. The results indicated that potassium on supported Rh metal catalysts had a promoting effect in the CO selective catalytic oxidation under H-2-rich stream, and microchannel reactor has an excellent ability to use in on-board hydrogen generation system. CO conversion keeps at high levels even at a very high GHSV as 500 000 h(-1), so, miniaturization of hydrogen generation system can be achieved by using the microchannel reactor. (C) 2004 Elsevier B.V. All rights reserved.

Mass transfer resistance in the production of high impact polypropylene

Mass transfer resistance in the production of high impact polypropylene (hiPP) produced by a two-stage slurry/gas polymerization was investigated by field-emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. It is found that the formation of ethylene-propylene copolymer (EPR) phases in polypropylene (iPP) particle produced in the first stage slurry polymerization exhibits a developing process from exterior to interior

Effect of Copolymerization Time on the Microstructure and Properties of Polypropylene/Poly(ethylene-co-propylene) In-Reactor Alloys

Three Polypropylene/Poly(ethylene-co-propylene) (PP/EPR) in-reactor alloys produced by a two-stage slurry/gas polymerization had different ethylene contents and mechanical properties, which were achieved by controlling the copolymerization time. The three alloys were fractionated into five fractions via temperature rising dissolution fractionation (TRDF), respectively. The chain structures of the whole samples and their fractions were analyzed using high-temperature gel permeation chromatography (GPC), Fourier transform infrared (FT-IR), C-13 nuclear magnetic resonance (C-13 NMR), and differential scanning calorimetry (DSC) techniques. These three in-reactor alloys mainly contained four portions: ethylenepropylene random copolymer (EPR), ethylene-propylene (EP) segmented and block copolymers, and propylene homopolymer. The increased copolymerization time caused the increased ethylene content of the sample. The weight percent of EPR, EP segmented and block copolymer also became higher.