Impact of sample preparation on mineralogical analysis of zero-valent iron reactive barrier materials

Permeable reactive barriers (PRBs) of zero-valent iron (Fe⁰) are increasingly being used to remediate contaminated ground water. Corrosion of Fe⁰ filings and tbe formation of precipitates can occur when the PRB material comes in contact with ground water and may reduce the lifespan and effectiveness of the barrier. At present, there are no routine procedures for preparing and analyzing the mineral precipitates from Fe⁰ PRB material. These procedures are needed because mineralogical composition of corrosion products used to interpret the barrier processes can change with iron oxidation and sample preparation. The objectives of this study were (i) to investigate a method of preparing Fe⁰ reactive barrier material for mineralogical analysis by X-ray diffraction (XRD), and (ii) to identify Fe mineral phases and rates of transformations induced by different mineralogical preparation techniques. Materials from an in situ Fe⁰ PRB were collected by undisturbed coring and processed for XRD analysis after different times since sampling for three size fractions and by various drying treatments. We found that whole-sample preparation for analysis was necessary because mineral precipitates occurred within the PRB material in different size fractions of the samples. Green rusts quickly disappeared from acetone-dried samples and were not present in air-dried and oven-dried samples Maghemite/magnetite content increased over time and in oven-dried samples, especially after heating to 105°C. We conclude that care must be taken during sample preparation of Fe⁰ PRB material, especially for detection of green rusts, to ensure accurate identification of minerals present within the barrier system.

Mechanochemical preparation of Ag catalysts for the n-octane-SCR de-NOx reaction: Structural and reactivity effects

Mechanochemical preparation of Ag/Al2O3 catalysts used for the selective catalytic reduction of NOx using hydrocarbons has been shown to substantially increase the activity of the catalyst in comparison with Ag/Al2O3 prepared by wet impregnation. The effect of using different ball-milling experimental parameters on both the structure of the material as well as the catalyst activity has been investigated and the optimum conditions established. A phase transition from γ- to α-alumina was observed milling at high speeds which was found to result in lower catalyst activities. At lower milling speeds both fracturing and agglomeration of the alumina support can be observed depending on the grinding time. However, due to ball-milling, a general enhancement in the NOx reduction activity was observed for all catalysts compared with the conventionally prepared catalysts irrespective of the reductant used. Transient DRIFTS-MS experiments were performed to investigate the effect of H2 in the absence and presence of water on the SCR reaction over catalysts prepared by both ball milling and wet impregnation. In-situ DRIFTS-MS analysis revealed significant differences in both gas phase and surface species. Most notably, isocyanate species were formed significantly more quickly and at higher surface concentration in the case of the mechanochemically prepared catalyst.

Synthesis by extrusion: continuous, large-scale preparation of MOFs using little or no solvent

Grinding solid reagents under solvent-free or low-solvent conditions (mechanochemistry) is emerging as a general synthetic technique which is an alternative to conventional solvent-intensive methods. However, it is essential to find ways to scale-up this type of synthesis if its promise of cleaner manufacturing is to be realised. Here, we demonstrate the use of twin screw and single screw extruders for the continuous synthesis of various metal complexes, including Ni(salen), Ni(NCS)(2)(PPh3)(2) as well as the commercially important metal organic frameworks (MOFs) Cu-3(BTC)(2) (HKUST-1), Zn(2-methylimidazolate)(2) (ZIF-8, MAF-4) and Al(fumarate)(OH). Notably, Al(fumarate)(OH) has not previously been synthesised mechanochemically. Quantitative conversions occur to give products at kg h(-1) rates which, after activation, exhibit surface areas and pore volumes equivalent to those of materials produced by conventional solvent-based methods. Some reactions can be performed either under completely solvent-free conditions whereas others require the addition of small amounts of solvent (typically 3-4 mol equivalents). Continuous neat melt phase synthesis is also successfully demonstrated by both twin screw and single screw extrusion for ZIF-8. The latter technique provided ZIF-8 at 4 kg h(-1). The space time yields (STYs) for these methods of up to 144 x 10(3) kg per m(3) per day are orders of magnitude greater than STYs for other methods of making MOFs. Extrusion methods clearly enable scaling of mechanochemical and melt phase synthesis under solvent-free or low-solvent conditions, and may also be applied in synthesis more generally.

Characterization of a reference material for BCR-ABL (M-BCR) mRNA quantitation by real-time amplification assays:towards new standards for gene expression measurements

Monitoring of BCR-ABL transcripts has become established practice in the management of chronic myeloid leukemia. However, nucleic acid amplification techniques are prone to variations which limit the reliability of real-time quantitative PCR (RQ-PCR) for clinical decision making, highlighting the need for standardization of assays and reporting of minimal residual disease (MRD) data. We evaluated a lyophilized preparation of a leukemic cell line (K562) as a potential quality control reagent. This was found to be relatively stable, yielding comparable respective levels of ABL, GUS and BCR-ABL transcripts as determined by RQ-PCR before and after accelerated degradation experiments as well as following 5 years storage at -20 degrees C. Vials of freeze-dried cells were sent at ambient temperature to 22 laboratories on four continents, with RQ-PCR analyses detecting BCR-ABL transcripts at levels comparable to those observed in primary patient samples. Our results suggest that freeze-dried cells can be used as quality control reagents with a range of analytical instrumentations and could enable the development of urgently needed international standards simulating clinically relevant levels of MRD.

Preparation of new materials by heterogeneous modification of cellulose

O presente trabalho teve como principal objectivo estudar a modificação química heterogénea controlada de fibras de celulose com diferentes reagentes de modo a alterar as suas propriedades de superfície, em especial em termos da criação de um carácter hidrofóbico e lipofóbico, preservando, sempre que possível, as suas propriedades mecânicas e, consequentemente, abrindo novas perspectivas de aplicação. O desenvolvimento do trabalho envolveu três abordagens principais, envolvendo, em cada caso, o estudo de diferentes condições reaccionais. Na primeira abordagem foram utilizados como reagentes de modificação compostos perfluorados, nomeadamente o anidrido trifluoroacético (TFAA), o cloreto de 2,3,4,5,6-pentafluorobenzoílo (PFBz) e o cloreto de 3,3,3- trifluoropropanoílo (TFP), para promover a acilação heterogénea da superfície das fibras. A segunda estratégia usada consistiu na preparação de híbridos de celulose do tipo orgânico-inorgânico classe-II, através da modificação das fibras de celulose com o (3-isocianatopropil)trietoxissilano (ICPTEOS), um reagente organossilano bifuncional. A ligação às fibras de celulose foi efectuada através das funções isocianato e, posteriormente, os grupos etoxissilano foram sujeitos a tratamentos de hidrólise ácida, como tal ou na presença de outros siloxanos, nomeadamente o tetraetoxissilano (TEOS) e o 1H,1H,2H,2Hperfluorodeciltrietoxissilano (PFDTEOS). Finalmente, a última abordagem foi baseada na modificação das fibras com triclorometilssilano (TCMS), através de uma reacção gás-sólido, que dispensou assim o uso de solventes orgânicos. A ocorrência de modificação química foi em cada caso confirmada por Espectroscopia de Infravermelho com Transformada de Fourier e Reflectância Total Atenuada (FTIR-ATR), Análise Elementar (EA) e determinação de ângulos de contacto. Adicionalmente, e dependendo de cada caso específico, diversas outras técnicas foram empregues na caracterização aprofundada dos materiais preparados, nomeadamente Ressonância Magnética Nuclear CPMAS no Estado Sólido (RMN), Espectroscopia de Difracção de Raios-X (XRD), Análise Termogravimétrica (TGA), Espectrometria de Massa de Iões Secundários com Análise de Tempo de Vôo (ToF-SIMS), Espectroscopia Fotoelectrónica de Raios-X (XPS) e Microscopia Electrónica de Varrimento (SEM). Relativamente à acilação das fibras de celulose com reagentes perfluorados, o sucesso da reacção foi comprovado por FTIR-ATR, EA, XPS e ToF-SIMS. Neste contexto, obtiveram-se fibras modificadas possuindo graus de substituição (DS) compreendidos entre 0.006 e 0.39. Verificou-se por XRD que, em geral, mesmo para os valores de DS mais elevados, a cristalinidade das fibras não foi afectada, indicando que a modificação foi limitada às camadas mais superficiais das mesmas ou a regiões amorfas das suas camadas mais internas. Adicionalmente, observou-se por ToF-SIMS que a distribuição dos grupos perfluorados à superfície das fibras foi, de facto, bastante heterogénea. Todos os derivados de celulose perfluorados apresentaram elevada hidrofobicidade e lipofobicidade, tendo-se atingido ângulos de contacto com água e diiodometano de 126º e 104º, respectivamente. Um aspecto interessante relativo a estes materiais é que a elevada omnifobicidade foi observada mesmo para valores de DS muito reduzidos, não se mostrando significativamente afectada pelo aumento dos mesmos. Em consonância, verificou-se por XPS que a cobertura da superfície das fibras de celulose com grupos perfluorados aumentou apenas ligeiramente com o aumento do DS, apontando para a esterificação de camadas mais internas das fibras, associada, neste caso, predominantemente aos seus domínios amorfos. No que diz respeito à estabilidade hidrolítica destes derivados, obtiveram-se dois tipos distintos de comportamento. Por um lado, as fibras de celulose trifluoroacetiladas são facilmente hidrolisáveis em meio neutro, e, por outro, as fibras pentafluorobenzoiladas e trifluoropropanoiladas mostram-se bastante resistentes face a condições de hidrólise em meio neutro e ácido (pH 4), podendo, contudo, ser facilmente hidrolisadas em meio alcalino (pH 9 e 12, para derivados do PFBz e do TFP, respectivamente). Na segunda abordagem verificou-se a ocorrência de reacção por FTIR-ATR e EA. Em geral, a modificação química com ICPTEOS ocorre predominantemente nas zonas mais superficiais das fibras de celulose ou em regiões amorfas. Contudo, em condições reaccionais mais severas (maior quantidade de reagente e tempo de reacção), esta atingiu também regiões cristalinas, afectando, consequentemente, a estrutura cristalina das fibras, como verificado por XRD. Por RMN de 29Si observou-se que após reacção com o ICPTEOS já existiam indícios de alguma hidrólise dos grupos etoxissilano, e que a sua subsequente condensação parcial tinha levado à formação de uma película inorgânica em redor das fibras (verificado por SEM), constituída maioritariamente por estruturas lineares, com uma contribuição mais modesta de estruturas “diméricas” e outras mais ramificadas. Consequentemente, este revestimento inorgânico transformou as fibras de celulose em materiais híbridos com elevada hidrofobicidade (ângulos de contacto com água entre 103-129º). A hidrólise ácida dos restantes grupos etoxissilano, como tal ou na presença de TEOS, originou híbridos de celulose com elevada hidrofilicidade, sendo impossível medirem-se os ângulos de contacto com água dos produtos finais, devido à presença maioritária de grupos silanol (Si-OH) e ligações Si-O-Si à superfície, os quais contribuíram para o consequente aumento de energia de superfície. No entanto, quando a hidrólise foi realizada na presença de PFDTEOS, obtiveram-se materiais híbridos com elevada hidrofobicidade e lipofobicidade (ângulos de contacto com água e diiodometano de 140º e 134º, respectivamente), devido à combinação da presença de grupos perfluorados e micro- e nano-rugosidades na superfície das fibras de celulose, conforme confirmado por SEM. Finalmente, a última abordagem permitiu preparar materiais derivados de celulose altamente hidrofóbicos e lipofóbicos (ângulos de contacto com água e diiodometano de 136º e 109º, respectivamente) por um processo simples, envolvendo tempos de tratamento tão curtos como 0.5 min. Este comportamento omnifóbico foi gerado pelo efeito sinergético entre a diminuição de energia de superfície das fibras, devido à presença de grupos metilo dos resíduos de TCMS ligados a estas, e a condensação dos resíduos de TCMS na forma de micro- e nano-partículas inorgânicas, que levou à criação de um revestimento rugoso à superfície das fibras, conforme observado por RMN de 29Si e SEM, respectivamente. A pré-humidificação das fibras de celulose demonstrou desempenhar um importante papel de “acelerador” dos processos de hidrólise e condensação das moléculas de TCMS. Nestas condições, o tempo de tratamento foi um dos parâmetros mais relevantes, pois para tempos de tratamento muito curtos (0.5 min) os materiais resultantes não apresentaram quaisquer diferenças a nível de propriedades físico-químicas em relação ao substrato de partida (a humidade em excesso consumiu todo o TCMS antes que este conseguisse reagir com os grupos hidroxilo das fibras de celulose), possuindo, por exemplo, valores de ângulos de contacto com água idênticos. Para tempos de tratamento mais longos, como 30 min, os materiais finais apresentaram a maior quantidade de componentes inorgânicos, tal como verificado por EA e TGA. Assim, o controlo da humidade das fibras é imperativo para se poder moldar as propriedades finais dos produtos. Esta última abordagem é particularmente promissora uma vez que tem como base um sistema simples e “verde” que pode ser facilmente implementado. Em conclusão, este trabalho permitiu demonstrar que a modificação química heterogénea controlada das fibras de celulose representa uma iniciativa promissora para a preparação de novos materiais obtidos a partir de recursos renováveis, com propriedades interessantes e passíveis de ser potencialmente aplicados em diferentes áreas. Para além do mais, as estratégias de modificação estudadas podem também ser precursoras de novos estudos que possam vir a ser desenvolvidos dentro do mesmo âmbito.

Pomegranate liquor preparation and analysis

The pomegranate (Punica granatum L.) liquor has been produced for several centuries in the south of Portugal, mainly in the mountain areas. The “Assaria” variety is the preferred cultivar due to its organoleptic properties and high arils to peel ratio. Wild pomegranates are also widely distributed but, despite the health benefits that have been associated to the fruits, they continue to be unappreciated for consumption. Liquor preparation is a very good alternative for wild pomegranate fruits. We prepared pomegranate liquors by following a maceration procedure using the arils or juice of Assaria and wild pomegranate fruits. Strawberry tree (Arbutus unedo L.) fruit spirits were used to prepare the liquors. At the end of the maceration time 5 day as minimum sugar syrup was added. The maturation period was three months or longer. The obtained liquors showed a very attractive pink colour. The colour and the total polyphenol, as well as the anthocyanin and ellagitannin profiles, were measured at the end of the maceration and maturation times. Wild pomegranates gave rise liquors with more intense pink colour and higher polyphenol contents than the prepared using Assaria fruits. The anthocyanin and ellagitannin profiles also indicated higher contents of polyphenols for liquors prepared using wild pomegranate fruits. When juice is used instead of complete arils during the maceration period punicalin is not present and the consequently total polyphenols is low. The main anthocyanins identified in the liquors were delphinidin-3,5-diglucoside, cyaniding-3,5-diglucoside, delphinidin–3-glucoside, cyaniding–3-glucoside, pelargonidin–3–glucoside; the main ellagitannins were punicalagin and punicalin.

Perturbing the impulse activity of a single identified neuron augments the formation of long-term memory in a molluscan semi-intact preparation /

The aim of this study was to investigate the neural correlates of operant conditioning in a semi-intact preparation of the pond snail, Lymnaea stagnalis. Lymnaea learns, via operant conditioning, to reduce its aerial respiratory behaviour in response to an aversive tactile stimulus to its open pneumostome. This thesis demonstrates the successful conditioning of na'ive semiintact preparations to show learning in the dish. Furthermore, these conditioned preparations show long-term memory that persists for at least 18 hours. As the neurons that generate this behaviour have been previously identified I can, for the first time, monitor neural activity during both learning and long-term memory consolidation in the same preparation. In particular, I record from the respiratory neuron Right Pedal Dorsal 1 (RPeD 1) which is part of the respiratory central pattern generator. In this study, I demonstrate that preventing RPeDl impulse activity between training sessions reduces the number of sessions needed to produce long-term memory in the present semi-intact preparation.

Preparation, Characterisation And Microwave Dielectric Properties Of Anbn-1o3n (N=5,6,8) Type Perovskite Compounds

The present study on the preparation , characterization and microwave dielectric properties of AnBn-1O3n (N=5,6,8) type perovskite compounds. The explored ceramics show dielectric constant between 11 and 54,quality factor in the range 2400 to 88900 GHz and Tf in the range -73 to +231ppm/0C.Most of the investigated cation deficient hexagonal perovskites show intermediate dielectric constant with high quality factors. This study gives a general introduction about material, scientific and technological aspects of DRs.Three important ,€r ,Q and Tf, used for the DR characterization are described. The relationship of the above parameters with the fundamental material characteristics is discussed. Different modes are excited when a DR is excited with suitable microwave spectrum of frequencies .A description of analytical determination of frequencies and construction of mode charts used for sample design and mode identification are also discussed. In this study several ceramics are developed for DR purposes, very little attention has been paid to grow the single crystals. It might be due to the fact that the difficulties and time involved in the growth of single crystals, big enough to function as microwave resonators make them expensive .However single crystals of these materials may have very high Q values. It is also possible that a better understanding of the dielectric properties in relation to the structure can be arrived using single crystals. Hence one of the future directions of dielectric resonator research should be to grow good quality single crystals of the above materials.

Preparation of sub-micrometre thick CulnSe2 films using sequential evaporation technique for device fabrication

In this work. Sub-micrometre thick CulnSe2 films were prepared using different techniques viz, selenization through chemically deposited Selenium and Sequential Elemental Evaporation. These methods are simpler than co-evaporation technique, which is known to be the most suitable one for CulnSe2 preparation. The films were optimized by varying the composition over a wide range to find optimum properties for device fabrication. Typical absorber layer thickness of today's solar cell ranges from 2-3m. Thinning of the absorber layer is one of the challenges to reduce the processing time and material usage, particularly of Indium. Here we made an attempt to fabricate solar cell with absorber layer of thickness

Preparation and characterization of micro and nano fiber reinforced natural rubber composites by latex stage processing

Use of short fibers as reinforcing fillers in rubber composites is on an increasing trend. They are popular due to the possibility of obtaining anisotropic properties, ease of processing and economy. In the preparation of these composites short fibers are incorporated on two roll mixing mills or in internal mixers. This is a high energy intensive time consuming process. This calls for developing less energy intensive and less time consuming processes for incorporation and distribution of short fibers in the rubber matrix. One method for this is to incorporate fibers in the latex stage. The present study is primarily to optimize the preparation of short fiber- natural rubber composite by latex stage compounding and to evaluate the resulting composites in terms of mechanical, dynamic mechanical and thermal properties. A synthetic fiber (Nylon) and a natural fiber (Coir) are used to evaluate the advantages of the processing through latex stage. To extract the full reinforcing potential of the coir fibers the macro fibers are converted to micro fibers through chemical and mechanical means. The thesis is presented in 7 chapters

An investigation on the preparation and properties of some transparent conducting oxides and lead selenide thin films”

The investigation of physical properties of matter has progressed so much during the last hundred years. Today physics is divided in to a large distinct group of special branches. These branches are distinguished by the particular area studied, method of investigation and so on. An independent and important branch that has developed is the physics ofthin films.Any object in solid or liquid form with one of its dimensions very much smaller than that of the other two may be called a thin film. It is having only one common property, namely, one of their dimensions is very small, though all their physical properties may be different. Thin layers of oil, floating on the surface of water, with their fascinating colours, have attracted men’s curiosity from time immemorial. The earliest application of thin films was the protective coatings in the form of paints. A thin layer of tin has been used from ancient times to protect copper utensils from corrosion. Indium thin films are used in certain applications on account of their good lubricating property. Relay contacts are coated with thin films of rare earth metals in order to prevent burning due to arcing. Hard coatings are also available using diamond like carbon (i-carbon). The basic properties of thin films are of considerable interest because of their potential applications in various fields of science and technology

The first preparation of beta-lactones by radical cyclization

beta-Lactones have, for the first time, been prepared by 4-exo-trig radical cyclization. Thus, alpha-ethenoyloxy radicals react in the presence of tributylstannane in a photothermal process to give beta-lactones. Highest yields were obtained when groups capable of stabilizing a carboncentered radical were present at the 3-position of the alkenoate acceptor.

Viability of Salmonella enterica subsp. enterica during the preparation and cold storage of Egyptian soft cheeses and ice-cream

Changes occurring in the viability of Salmonella enterica subsp. enterica during the preparation and cold storage of Domiati cheese, Kariesh cheese and ice-cream were examined. A significant decrease in numbers was observed after whey drainage during the manufacture of Domiati cheese, but Salmonella remained viable for 13 weeks in cheeses prepared from milks with between 60 and 100 g/L NaCl; the viability declined in Domiati cheese made from highly salted milk during the later stages of storage. The method of coagulation used in the preparation of Kariesh cheese affected the survival time of the pathogen, and it varied from 2 to 3 weeks in cheeses made with a slow-acid coagulation method to 4-5 weeks for an acid-rennet coagulation method. This difference was attributed to the higher salt-in-moisture levels and lower pH values of Kariesh cheese prepared by the slow-acid coagulation method. A slight decrease in the numbers of Salmonella resulted from ageing ice-cream mix for 24 h at 0degreesC, but a greater reduction was evident after one day of frozen storage at -20degreesC. The pathogen survived further frozen storage for four months without any substantial change in numbers.

Preparation and magnetic properties of La–Mn and La–Co doped barium hexaferrites prepared via an improved co-precipitation/molten salt method

LaMn and LaCo doped barium hexaferrites of formula Ba(1-x)LaxFe(12-x)MxO19 (M=Mn, Co) (x=0.05 to 0.40) were prepared with an improved co-precipitation/molten salt method. For the synthesis, aqueous solutions of the appropriate metal chlorides were prepared in the ratio required except that the initial mole ratio of Fe and dopants to Ba was chosen to be 11:1, and then mixed with excess Na2CO3. The solutions were then cooled, filtered off, dried, then mixed with KCl flux, and heated at 450 degrees C and for 2 h. The temperature was then raised to 950 degrees C and kept for 4 h, then cooled. This new synthesis method, which employs a lower temperature and shorter reaction time, gives products with improved crystallinity and purity while the saturation magnetization and coercivity values are comparable with those synthesized via the high temperature method.

Efficiency and purity control in the preparation of pure and/or aluminum-doped barium ferrites by hydrothermal methods using ferrous ions as reactants

The synthesis of hexagonal barium ferrite (BaFe12O19) was studied under hydrothermal conditions by a method in which a significant amount of ferrous chloride was introduced along side ferric chloride among the starting materials. Though all of the Fe2+ ions in the starting material were converted to Fe3+ ions in the final product, Fe2+ was confirmed to participate differently from the Fe3+ used in the conventional method in the mechanism of forming barium ferrite. Indeed the efficiency of the synthesis and the quality of the product and the lack of impurities such as Fe2O3 and BaFe2O4 were improved when Fe2+ was included. However, the amount of ferrous ions that could be included to obtain the desired product was limited with an optimum ratio of 2:8 for FeCl2/FeCl3 when only 2h of reaction time were needed. It was also found that the role of trivalent Fe3+ could be successfully replaced by Al3+. Up to 50% of their on could be replaced by Al3+ in the reactants to produce Al- doped products. It was also found that the ratio of Fe2+/M3+ could be increased in the presence of Al3+ to produce high quality barium ferrite.