Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Wastewater Treatment and Deinking Sludge Utilization Possibilities for Energy and Material Recovery in the Leningrad Region

Operation of pulp and paper mills generates waste including wastewater treatment sludge and deinking sludge. Both sludge types are generated in large amounts and are mainly disposed of in landfills in the Leningrad Region resulting in environmental degradation. The thesis was aimed at seeking new sustainable ways of sludge utilization. Two paper mills operating in the Leningrad Region and landfilling their sludge were identified: “SCA Hygiene Products Russia” and “Knauf”. The former generates 150 t/day of deinking sludge, the latter – 145 t/day of secondary sludge. Chemical analyses of deinking sludge were performed to assess applicability of sludge in construction materials production processes. Higher heating value on dry basis of both sludge types was determined to evaluate energy potential of sludge generated in the Leningrad Region. Total energy output from sludge incineration was calculated. Deinking sludge could be utilized in the production process of “LSR-Cement” or “Slantsy Cement Plant Cesla” factories, and “Pobeda” and “Nikolsky” brick mills without exceeding current sludge management costs.

Polyphenoloxidase and peroxidase in avocado pulp (Persea americana Mill.)

The aim of the present investigation was to evaluate the enzymatic activity of polyphenoloxidase and peroxidase in avocado pulps, from the Northwest area of Paraná-Brazil, in order to compare the varieties on their enzymatic activity for both, minimum and industrial processing. Enzymatic extracts were prepared from avocado pulp of Choquete, Fortuna and Quintal varieties, in green and ripe maturation stage. Thermal treatment was applied with temperatures 60, 65, 70, 75 and 80 °C. The enzymatic activities were determined by using spectrophotometer. A decline of polyphenoloxidase activity was observed in all of the varieties when both, temperature and time increased. Total inactivation of enzymes was not observed in the largest temperature. Fortuna and Choquete variety showed the lowest polyphenoloxidase activity in the ripe stage. Soluble peroxidase showed activity in the green stage, whereas, ionically bound peroxidase activity increased with the change from green to ripe maturation stage in Choquete variety.

Identification and characterisation of phenolic compounds extracted from Moroccan olive mill wastewater

Olive mill wastewater, hereafter noted as OMWW was tested for its composition in phenolic compounds according to geographical areas of olive tree, i.e. the plain and the mountainous areas of Tadla-Azilal region (central Morocco). Biophenols extraction with ethyl acetate was efficient and the phenolic extract from the mountainous areas had the highest concentration of total phenols' content. Fourier-Transform-Middle Infrared (FT-MIR) spectroscopy of the extracts revealed vibration bands corresponding to acid, alcohol and ketone functions. Additionally, HPLC-ESI-MS analyses showed that phenolic alcohols, phenolic acids, flavonoids, secoiridoids and derivatives and lignans represent the most abundant phenolic compounds. Nüzhenide, naringenin and long chain polymeric substances were also detected. Mountainous areas also presented the most effective DPPH scavenging potential compared to plain areas; IC50 values were 11.7 ± 5.6 µg/ml and 30.7 ± 4.4 µg/ml, respectively. OMWW was confirmed as a rich source of natural phenolic antioxidant agents.

Record of pre-conference of the Pacific Coast local unions affiliated with the International Brotherhood of Pulp, Sufphite & Papermill Workers, the International Brotherhood of Paper Makers, May 21, 1942 to May 25, 1942, Portland Oregon /

"O.E.U., union label, # 16821."

The Influence Of The Buffering Capacity On The Production Of Organic Acids And Alcohols From Wastewater In Anaerobic Reactor.

Some bacteria common in anaerobic digestion process can ferment a broad variety of organic compounds to organic acids, alcohols, and hydrogen, which can be used as biofuels. Researches are necessary to control the microbial interactions in favor of the alcohol production, as intermediary products of the anaerobic digestion of organic compounds. This paper reports on the effect of buffering capacity on the production of organic acids and alcohols from wastewater by a natural mixed bacterial culture. The hypothesis tested was that the increase of the buffering capacity by supplementation of sodium bicarbonate in the influent results in benefits for alcohol production by anaerobic fermentation of wastewater. When the influent was not supplemented with sodium bicarbonate, the chemical oxygen demand (COD)-ethanol and COD-methanol detected in the effluent corresponded to 22.5 and 12.7 % of the COD-sucrose consumed. Otherwise, when the reactor was fed with influent containing 0.5 g/L of sodium bicarbonate, the COD-ethanol and COD-methanol were effluents that corresponded to 39.2 and 29.6 % of the COD-sucrose consumed. Therefore, the alcohol production by supplementation of the influent with sodium bicarbonate was 33.6 % higher than the fermentation of the influent without sodium bicarbonate.

Technological advances and mechanistic basis for fungal biopulping

Biopulping fundamentals, technology and mechanisms are reviewed in this article. Mill evaluation of Eucalyptus grandis wood chips biotreated by Ceriporiopsis subvermispora on a 50-tonne pilot-plant demonstrated that equivalent energy savings can be obtained in lab- and mill-scale biopulping. Some drawbacks concerning limited improvements in pulp strength and contamination of the chip pile with opportunist fungi have been observed. The use of pre-cultured wood chips as inoculum seed for the biotreatment process minimized contamination problems related to the use of blended mycelium and corn-steep liquor in the inoculation step. Alkaline wash restored part of the brightness in biopulps and marketable brightness values were obtained by one-stage bleaching with 5% H2O2 when bio-TMP pulps were under evaluation. Considering the current scenario, the understanding of biopulping mechanisms has gained renewed attention because more resistant and competitive fungal species could be selected with basis on a function-directed screening project. A series of studies aimed to elucidate structural changes in lignin during wood biodegradation by C. subvermispora had indicated that lignin depolymerization occurs during initial stages of wood biotreatment. Aromatic hydroxyls did not increase with the split of aryl-ether linkages, suggesting that the ether-cleavage-products remain as quitione-type structures. On the other hand, cellulose is more resistant to the attack by C subvermispora. MnP-initiated lipid peroxidation reactions have been proposed to explain degradation of non-phenolic lignin substructures by C subvermispora, while the lack of cellobiohydrolases and the occurrence of systems able to suppress Fenton`s reaction in the cultures have explained non-efficient cellulose degradation by this biopulping fungus. (C) 2007 Elsevier Inc. All rights reserved.

Metsäteollisuuden jätevedenpuhdistamon lietteiden vaihtoehtoiset käsittelymenetelmät.

Työ on tehty osana ympäristöklusterin tutkimusohjelmaa "Materiaalivirrat ja energiankäyttö metsäteollisuusintegraatissa ja niihin liittyvät toimintastrategiat ympäristövaikutuslähtöisesti". Juha Räsänen on tehnyt metsäteollisuuden sivuainevirroista projektissa perusselvityksen, joka on tämän työn pohjana. Työn tavoitteena on ollut selvittää neljän itäsuomalaisen metsäteollisuusintegraatin tapauksissa vaihtoehtoisten lietteenkäsittelymenetelmien tekninen ja taloudellinen soveltuvuus nykyiseen käsittelyyn verrattuna. Tutkimuksessa hyödynnettiin aikaisempia tutkimustuloksia ja eri laitevalmistajien ja metsäteollisuusintegraattien kokemuksia. Työssä esitettäviä arvioita voidaan hyödyntää myös sektoritasolla. Metsäteollisuuden jätevedenpuhdistamon lietteistä käsiteltävyyden kannalta vaativin on bioliete, jonka osuuden kasvaessa perinteinen mekaaninen puristaminen ja poltto vaikeutuvat useilla tehtailla merkittävästikin nykyään ja lähivuosina. Polton ongelmat ja niistä aiheutuva ajoittainen aumakompostointitarve voivat puoltaa joko sekalietteen termistä tai biotermistä kuivausta ennen polttamista. Toinen tapa ratkaista lieteongelma on käsitellä bio- ja primäärilietteet erikseen. Biolietteen lipeälinjakäsittelyssä liete lingotaan, käsitellään mustalipeällä, haihdutetaan ja poltetaan soodakattilassa. Bioliete voidaan myös mädättää ja käsitellä sen jälkeen perinteisessä mekaanisessa puristuksessa. Kaikki käsitellyt menetelmät ovat teknisesti toteutettavissa, kunhan tietyt prosessireunaehdot täyttyvät. Vaihtoehtoiset käsittelymenetelmät vähentävät lietteen jäteluonnetta, mutta vastaavasti kustannukset lisääntyvät usein merkittävästi. Menetelmien käytöstä aiheutuvat integraatin puhdistamolietteen käsittelyn kokonaiskustannukset laskettiin työn osana olevalla taulukkolaskentasovelluksella laitetoimittajien budjettitarjouksia hyödyntäen. Biolietteen poltto soodakattilassa tarjoaa kustannusten kannalta houkuttelevimman ratkaisun. Työhön sisältyvää laskentamenettelyä voidaan soveltaa periaatteessa minkä tahansa metsäteollisuusintegraatin tapaukseen.

Testing and Monitoring Mill Connection Messages

Tarve tälle työlle on noussut sanomapalvelinsoveluksissa (servers) esiintyvistä ongelmista. Sanomapalvelinsovelluksia käytetään lähettämään ja vastaanottamaan sanomia paperiteollisuuden myynnin ja jakelun järjestelmässä maantieteellisesti erillään olevista paperiteollisuuden tehtaista. Sanomapalvelinsovelusten kunnollinen toimivuus on tärkeää koko järjestelmän toimivuuden kannalta, koska nämä palvelimet käsittelevät päivittäin tuhansia sanomia, jotka sisältävät merkityksellistä järjestelmätietoa. Tässä työssä on tutkittu mahdollisia toteutustekniikoita ja näihin tutkimuksiin pohjautuen toteutettu työkalut sanomapalvelinsovellusten testaukseen ja valvontaan. Sovellus-arkkituuritekniikoita tutkittaessa tutkimus rajattiin 3-tasoarkkitehtuuritekniikkaan, erityisesti TUXEDOTM -järjestelmätekniikkaan, koska toteutettavaa sovellusta käytetään hajautetussa sovellusympäristössä. Sovellusasiakkaan (client) toteutusta varten tutkittiin ja vertailtiin XML-tekniikkaa ja Microsoft Visual C++ -tekniikkaa käytettynä Tieto-Enatorin Phobos Interaktiivisen C++ -luokkakirjaston kanssa. XML-tekniikoita sekä Visual C++ ja Phobos-luokkakirjasto –tekniikkaa tutkittiin niiltä osin, mitä tarvittiin sanomamerkkijonojen katseluun. XML-tietokantatekniikoita tutkittiin mahdollisena vaihtoehtona tietokanta ja sovelluspalvelintekniikalle. Työn ensimmäisenä tavoitteena oli toteuttaa työkalu sanomapalvelinsovellusten testaamiseen. Toisena tavoitteena oli toteuttaa työkalu sanomien sisällön oikeellisuuden valvontaan. Kolmantena tavoitteena oli analysoida olemassaolevaa sanomavirheiden valvontasovellusta ja kehittää sitä eteenpäin. Diplomityön tuloksena toteutettiin sovellus sanomapalvelinsovellusten testaamiseen ja valvontaan. Tutkituista asiakassovelustekniikoista valittiin toteutus-tekniikaksi MS Visual C++ käytettynä Phobos Interaktiivisen C++ luokkakirjaston kanssa tekniikan tunnettavuuden vuoksi. 3-taso TUXEDOTM-tekniikka valittiin sovelluksen arkkitehtuuriksi. Lisäksi löydettiin parannuksia olemassa oleviin sanoma-virheiden valvontatoimintoihin. Tutkitut toteutustekniikat ovat yleisiä ja niitä voidaan käyttää, kun toteutetaan samanlaisia sovelluksia samanlaisiin sovellusympäristöihin.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Improving the Supply Chain Performance Management System in a Finnish paper mill

This Master’s Thesis studies performance management system and its benefits, risks and costs. Objective of the thesis is to describe and evaluate currently used supply chain performance management system (SCPMS) in a Finnish paper mill and its interfaces with its business unit’s SCPMS. As a result, the host company has improvement road map for improving its SCPMS. Used SCPMS in the host company and its interfaces to business unit’s SCPMS are described based on interviews held in the host company and the business unit. Evaluation of the host company’s SCPMS is based on literature study. For improvement road map, three areas in need of improvements are chosen. The study shows the need of high level top management commitment in successful performance management system implementation and usage, especially when the system is deployed to lower levels in the organization.