Comparison of Q-factors between TE and TM modes in 3-D microsquares by FDTD simulation

Mode characteristics of three-dimensional (3-D) microsquare resonators are investigated by finite-difference time-domain (FDTD) simulation for the transverse electric (TE)-like and the transverse magnetic (TM)-like modes. For a pillar microsquare with a side length of 2 pin in air, we have Q-factors about 5 X. 103 for TM-like modes at the wavelength of 1550 run, which are one order larger than those of TE-like modes, as vertical refractive index distribution is 3.17/3.4/3.17 and the cororresponding center layer thickness is 0.2 mu m. The mode field patterns show that TM-like modes have much weaker vertical radiation coupling loss than TE-like modes. TM-like modes can have high Q-factors in a microsquare with weak vertical field confinement.

Electrically Driven InAs Quantum-Dot Single-Photon Sources

Electrically driven single photon source based on single InAs quantum dot (QDs) is demonstrated. The device contains InAs QDs within a planar cavity formed between a bottom AlGaAs/GaAs distributed Bragg reflector (DBR) and a surface GaAs-air interface. The device is characterized by I-V curve and electroluminescence, and a single sharp exciton emission line at 966nm is observed. Hanbury Brown and Twiss (HBT) correlation measurements demonstrate single photon emission with suppression of multiphoton emission to below 45% at 80K

TEMPERATURE EFFECT ON POROUS SILICON LUMINESCENCE

A theoretical surface-state model of porous-silicon luminescence is proposed. The temperature effect on the PhotoLuminescence (PL) spectrum for pillar and spherical structures is considered, and it is found that the effect is dependent on the doping concentration, the excitation strength, and the shape and dimensions of the Si microstructure. The doping concentration has an effect on the PL intensity at high temperatures and the excitation strength has an effect on the PL intensity at low temperaturs. The variations of the PL intensity with temperature are different for the pillar and spherical structures. At low temperatures the PL intensity increases in the pillar structure, while in the spherical structure the PL intensity decreases as the temperature increases, at high temperatures the PL intensities have a maximum for both models. The temperature, at which the PL intensity reaches its maximum, depends on the doping concentration. The PL spectrum has a broader peak structure in the spherical structure than in the pillar structure. The theoretical results are in agreement with experimental results.

Formation and modeling of disinfection by-products in drinking water of six cities in China

Funding and support for this project was provided by NSFC (Grant No. 40771015), and Key International Science and Technology Cooperation Projects (Grant No. 22007DFC20180). The authors also gratefully acknowledge the support of Key Projects in the National Science & Technology Pillar Program in the Eleventh Five-year Plan Period (Grant No. 2006BAD01B06-02). The authors thank the CDCs of Daqing, Beijing, Tianjin, Zhengzhou, Changsha and Shenzhen cities for field and laboratory technical support.

Changes in individual plant traits and biomass allocation in alpine meadow with elevation variation on the Qinghai-Tibetan Plateau

Plant traits and individual plant biomass allocation of 57 perennial herbaceous species, belonging to three common functional groups (forbs, grasses and sedges) at subalpine (3700 m ASL), alpine (4300 m ASL) and subnival (>= 5000 m ASL) sites were examined to test the hypothesis that at high altitudes, plants reduce the proportion of aboveground parts and allocate more biomass to belowground parts, especially storage organs, as altitude increases, so as to geminate and resist environmental stress. However, results indicate that some divergence in biomass allocation exists among organs. With increasing altitude, the mean fractions of total biomass allocated to aboveground parts decreased. The mean fractions of total biomass allocation to storage organs at the subalpine site (7%+/- 2% S.E.) were distinct from those at the alpine (23%+/- 6%) and subnival (21%+/- 6%) sites, while the proportions of green leaves at all altitudes remained almost constant. At 4300 m and 5000 m, the mean fractions of flower stems decreased by 45% and 41%, respectively, while fine roots increased by 86% and 102%, respectively. Specific leaf areas and leaf areas of forbs and grasses deceased with rising elevation, while sedges showed opposite trends. For all three functional groups, leaf area ratio and leaf area root mass ratio decreased, while fine root biomass increased at higher altitudes. Biomass allocation patterns of alpine plants were characterized by a reduction in aboveground reproductive organs and enlargement of fine roots, while the proportion of leaves remained stable. It was beneficial for high altitude plants to compensate carbon gain and nutrient uptake under low temperature and limited nutrients by stabilizing biomass investment to photosynthetic structures and increasing the absorption surface area of fine roots. In contrast to forbs and grasses that had high mycorrhizal infection, sedges had higher single leaf area and more root fraction, especially fine roots.

Analysis of arable land loss and its impact on rural sustainability in Southern Jiangsu Province of China

Rapid urbanization and industrialization in southern Jiangsu Province have consumed a huge amount of arable land. Through comparative analysis of land cover maps derived from TM images in 1990, 2000 and 2006, we identified the trend of arable land loss. It is found that most arable land is lost to urbanization and rural settlements development. Urban settlements, rural settlements, and industrial park-mine-transport land increased, respectively, by 87 997 ha (174.65%), 81 041 ha (104.52%), and 12 692 ha (397.99%) from 1990 to 2006. Most of the source (e.g., change from) land covers are rice paddy fields and dryland. These two covers contributed to newly urbanized areas by 37.12% and 73.52% during 1990-2000, and 46.39% and 38.86% during 2000-2006. However, the loss of arable land is weakly correlated with ecological service value, per capita net income of farmers, but positively with grain yield for some counties. Most areas in the study site have a low arable land depletion rate and a high potential for sustainable development. More attention should be directed at those counties that have a high depletion rate but a low potential for sustainable development. Rural settlements should be controlled and rationalized through legislative measures to achieve harmonious development between urban and rural areas, and sustainable development for rural areas with a minimal impact on the ecoenvironment. (C) 2009 Elsevier Ltd. All rights reserved.

Biofunctionalization of CeF3 : Tb3+ nanoparticles

CeF3: Tb3+ nanoparticles (short pillar-like morphology with an average length and width of 11 and 5 nm, respectively) were successfully prepared by a polyol process using diethyleneglycol (DEG) as solvent. After being functionalized with a SiO2-NH2 layer, these CeF3: Tb3+ nanoparticles can be conjugated with biotin molecules (activated by thionyl chloride) and further with avidin. The as-formed CeF3: Tb3+ nanoparticles, CeF3: Tb3+ nanoparticles functionalized with amino groups, biotin conjugated amino-functionalized CeF3: Tb3+ nanoparticles and biotinylated CeF3: Tb3+ nanoparticles bonded with avidin were characterized by x-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), UV/vis absorption spectra and luminescence spectra, respectively. The biofunctionalization of the CeF3: Tb3+ nanoparticles has less effect on their luminescence properties, i.e. they still show strong green emission (from Tb3+, with D-5(4) - F-7(5) at 543 nm as the most prominent group), indicative of the great potential for these CeF3: Tb3+ nanoparticles to be used as biological fluorescence probes.

Embryology of Crawfurdia delavayi (Gentianaceae) and its systematic value

The embryological characters of Crawfurdia delavayi Frabnch. are described and the systematic relationships of Crawfurdia discussed. Anthers are tetrasporangiate. The development of anther walls conforms to the Dicotyledonous type. The tapetum is of single origin. The development of the tapetum with uninucleate cells is of the glandular type. The tapetal cells on the connective side show radial elongation or periclinal division and intrude into the anther locule. The epidermis of anther walls persists and its cells become pillar and fibrous, and the endothecium degenerates. The ovary is bicarpellary and unilocular. The placentation is typically parietal with 8 rows of anatropous ovules. The development of embryo sac is of the polygonum type. Before fertilization, two polar nuclei fuse into a secondary nucleus. Three antipodal cells persist. Flowers are protandrous. Fertilization is porogamous. The development of the endosperm is of the nuclear type. The embryogeny corresponds to the solanad type physalis II variation. The embryological data indicate that it is better to separate Crawfurdia from Gentiana as an independent genus.

岩体力学参数及稳定性能量判据研究

There are two major problems that have been concerned all the times, which are the mechanics characters of joint rock mass and the criterion for stability of engineering rock. Aim at the two problems, several works were conducted as follow: (1) Firstly, the mechanics characters of rock mass was studied by means of the Distinct Element Code. Subsequently, it was studied that the sensibility of joint surface roughness, strength of joint wall, joint stiffness ( i.e. tangential and normal stiffness) on the rock mass strength. (2) Based on the experimental rock mass classification methods of RMR and GSI, the program of “Parameters Calculation of the Rock Mass ” was developed. It has realized the rapid choice of rock mass parameters. (3) The concept of Representive Element Volume was induced based on the study of dimensional effect of rock mass. The Representive Element Volume of the horizontal and vertical pillar (ab. Two Pillars ) in the 2nd zone of Jinchuan mine were gained by the Geology Statistic Method and the Distinct Element Code. And then, the strength and deformatiom parameters of rock mass of the Two Pillars were obtained through numerical experiment. (4) From the confining depressure after thriaxial compression test of rock sample, it was concluded that the failure of rock is caused mainly by the lateral deformation and energy release happened during the confining depressure processure. The criterion of plastic energy catastrophe of rock engineering failure was proposed and validated. Subsquently, the stability of the horizontal pillar and Qianjiangping landslide in Three Gorges was judged by means of above-mentioned method. (5) Based on the fact there is a phenomenon of increasing energy concentration while the rock mass was compressed, rock information entropy (i.e. energy distribution entropy) was proposed. And it was revealed that there was change of energy distribution entropy while the rock mass was compressed to failure.

Getting Constitutional Theory into Proportion: A Matter of Interpretation?

Gibbs, N., Getting Constitutional Theory into Proportion: A Matter of Interpretation?, Oxford Journal of Legal Studies, 27 (1), 175-191. RAE2008

Rola unijnych państw neutralnych w procesie budowy architektury bezpieczeństwa w Europie

Wydział Nauk Politycznych i Dziennikarstwa: Stosunki Międzynarodowe

DOŚWIADCZENIE PRZESTRZENI W PAMIĘCI O HOLOCAUŚCIE

This paper analyzes different experiences of space by which memory of Holocaust could be passed on. The Memorial for the murdered Jews of Europe in Berlin gives visitors the feeling of insecurity and overwhelms them with monumentality. For that reason it is criticized as reflecting the other side of German memory: The Third Reich’s megalomania and dream about power. The Hamburger memorial against fascism designed in 1986 by conceptual artists Jochen and Esther Gerz offers quite an opposite experience of space. A twelve-meter-high pillar has been established for visitors to sign on it. Once the area was covered by signature it was lowered into the ground till it completely disappeared. The intention of the artists was to put memory not into the monument but into people. Pozdrowienia z Alej Jerozolimskich (Greetings from the Jerusalem Avenue, 2002) by Joanna Rajkowska – a fifteen-meter tall artificial palm tree installed in the centre of Warsaw – is an attempt to infuse with Israel's scenery a Warsaw's street whose name and history sends the observer to the history of the Jews in Poland. In another work called Dotleniacz (Oxygenator, 2007) Rajkowska created an artificial lake with oxygen concentrators, gold fish, flowers and banks. Again, the installation was placed in a very meaningful place – Grzybowski Square – which is strongly connected with Jewish life in Poland as well as Polish anti-Semitism. The synagogue in Poznan was transformed during the Nazi occupation into a swimming pool which it has remained until the present day. This fact ( just like the building) seems to be invisible for most citizens. In 2003 Rafał Jakubowicz changed the fact by projecting a Hebrew inscription הייחש-תכירב (swimming pool) on the façade of the former synagogue. In Berek (The Game of Tag, 1999) by Artur Żmijewski a group of naked men and women of various age play tag. The artist filmed them in two rooms: in a symbolically neutral space and in a gas chamber of a former Nazi death camp. The film is an attempt at breaking the spell of this horrifying and paralysing space.

Percepções dos profissionais de farmácia sobre os conhecimentos na área da Homeopatia

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Ciências Farmacêuticas

Reflections on the transformation of my meaning making to support the organic growth of a firm

The objective of my Portfolio is to explore the working hypothesis that the organic growth of a firm is governed by the perspectives of individuals and such perspectives are governed by their meaning-making. The Portfolio presents explorations of the transformation of my meaning making and in adopting new practices to support the organic growth of a firm. I use the work of other theorists to transition my understanding of how the world works. This transition process is an essential tool to engage with and understand the perspectives of others and develop a mental capacity to “train one’s imagination to go visiting” (Arendt, 1982; p.43). The Portfolio, therefore, is primarily located in reflective research. Using Kegan’s (1994) approach to Adult Mental Development, and Sowell’s (2007) understanding of the visions which silently shape our thoughts I organise the developments of my meaning making around three transformation pillars of change. In pillar one I seek to transform an unthinking respect for authority and break down a blind pervasiveness of thought within my reasoning process arising from an instinct for attachment and support from others whom I trust. In pillar two I seek to discontinue using autocratic leadership and learn to use the thoughts and contributions of a wider team to make improved choices about uncertain future events. In pillar three I explore the use of a more reflective thinking framework to test the accuracy of my perceptions and apply a high level of integrity in my reasoning process. The transformation of my meaning making has changed my perspectives and in turn my preferred practices to support the organic growth of a firm. I identify from practice that a transformative form of leadership is far more effective that a transactional form of leadership to stimulate the trust and teamwork required to sustain the growth a firm. Creating an environment where one feels free to share thoughts and feelings with others is an essential tool to build a team to critique the thoughts of one other. Furthermore, the entrepreneurial wisdom to grow a firm must come from a wider team, located both inside and outside the boundaries of a firm. No individual or small team has the mental capacity to provide the entrepreneurship required to drive the organic growth of a firm. I address my Portfolio to leaders in organisations who have no considered framework on the best practices required to lead a social organisation. These individuals may have no sense of what they implicitly believe drives social causation and they may have no understanding if their meaning making supports or curtails the practices required to grow a firm. They may have a very limited capacity to think in a logical manner, with the result they are using guesses from their ‘gut’ to make poor judgements in the management of a firm.

Analysis of the structural characteristics of an intermediate rail vehicle and their effect on vehicle crash performance

In the current paper, the authors present an analysis of the structural characteristics of an intermediate rail vehicle and their effects on crash performance of the vehicle. Theirs is a simulation based analysis involving four stages. First, the crashworthiness of the vehicle is assessed by simulating an impact of the vehicle with a rigid wall. Second, the structural characteristics of the vehicle are analysed based on the structural behaviour during this impact and then the structure is modified. Third, the modified vehicle is tested again in the same impact scenario with a rigid wall. Finally, the modified vehicle is subjected to a modelled head-on impact which mirrors the real-life impact interface between two intermediate vehicles in a train impact. The emphasis of the current study is on the structural characteristics of the intermediate vehicle and the differences compared to an impact of a leading vehicle. The study shows that, similar to a leading vehicle, bending, or jackknifing is a main form of failure in this conventionally designed intermediate vehicle. It has also been found that the location of the door openings creates a major difference in the behaviour of an intermediate vehicle. It causes instability of the vehicle in the door area and leads to high stresses at the joint of the end beam with the solebar and shear stresses at the joint of the inner pillar with the cantrail. Apart from this, the shapes of the vehicle ends and impact interfaces are also different and have an effect on the crash performance of the vehicles. The simulation results allow the identification of the structural characteristics and show the effectiveness of relevant modifications. The conclusions have general relevance for the crashworthiness of rail vehicle design