Fabrication and analysis of self-assembled photonic crystals structures

This paper presents the fabrication and analysis of a three-dimensional FCC photonic crystal (PhC) based on a self-assembly synthesis of monodispersive latex spheres. Experimental optical characterization, achieved by measurements of the specular reflectance under variable angles, indicated the clear presence of a Bragg diffraction pattern. Results are further explored by theoretical calculations based on the Finite Difference Time Domain (FDTD) method to determine the full PhC band structure.

The effect of ZnO on the sintering and stabilization of ZrO2 center dot MgO system

The sintering of ZrO2. MgO . ZnO powder has been investigated by TMA (Thermal Mechanical Analyser) and its phases analysed by XRD (X-ray diffraction pattern). The data obtained from sintering was studied by the Bannister equation and its dominant sintering mechanism was calculated. It was observed that the ZnO addition in the ZrO2. MgO solid solution lead to increased zirconia stabilization, According to the vacancies model, the ZnO addition did not lead to zirconia phases stabilization (PSZ). An analysis of the rate control in the initial stage of the sintering (region I) showed a mechanism of volume diffusion type. In other regions (regions II and III), the grain growth did lead to the Bannister equation deviation, which was observed by SEM (Scanning Electron Microscopy). These results were different from those demonstrated by other authors who studied the ZrO2. Y2O3 solid solution and obtained a mechanism of grain boundary diffusion type. (C) 1999 Published by Elsevier B.V. Ltd and Techna S.r.l. All rights reserved.

Iron(II) djenkolate: synthesis and properties

Djenkolate complex of iron, [Fe(C(7)H(12)N(2)O(4)S(2))]. H(2)O, has been synthesized by the reaction of potassium djenkolate with Fe(SO(4)). 7H(2)O under nitrogen atmosphere. X-Ray diffraction pattern has been indexed in orthorhombic system with lattice parameters: a=11.24 Angstrom, b=7.50 Angstrom and c=6.96 Angstrom. According to IR spectroscopy, coordination is performed through COO(-) and NH(2) groups. An octahedral geometry for Fe ion is suggested by UV-Vis and Mossbauer spectroscopies. Thermal decomposition leads to the formation of Fe(2)O(3) (hematite). The compound shows poor solubility in water and in common organic solvents. (C) 2000 Elsevier B.V. S.A. All rights reserved.

Drude's model calculation rule on electrical transport in Sb-doped SnO2 thin films, deposited via sol-gel

The evaluation of free carrier concentration based on Drude's theory can be performed by the use of optical transmittance in the range 800-2000 nm (near infrared) for Sb-doped SnO2 thin films. In this article, we estimate the free carrier concentration for these films, which are deposited via sol-gel dip-coating. At approximately 900 mn, there is a separation among transmittance curves of doped and undoped samples. The plasma resonance phenomena approach leads to free carrier concentration of about 5 x 1020 cm(-3). The increase in the Sb concentration increases the film conductivity; however, the magnitude of measured resistivity is still very high. The only way to combine such a high free carrier concentration with a rather low conductivity is to have a very low mobility. It becomes possible when the crystallite dimensions are taken into account. We obtain grains with 5 nm of average size by estimating the grain size from X-ray diffraction data, and by using line broadening in the diffraction pattern. The low conductivity is due to very intense scattering at the grain boundary, which is created by the presence of a large amount of nanoscopic crystallites. Such a result is in accordance with X-ray photoemission spectroscopy data that pointed to Sb incorporation proportional to the free electron concentration, evaluated according to Drude's model. (c) 2006 Elsevier Ltd. All rights reserved.

Collagen-hydroxyapatite films: piezoelectric properties

In this paper we report a study of the physicochemical, dielectric and piezoelectric properties of anionic collagen and collagen-hydroxyapatite (HA) composites, considering the development of new biomaterials which have potential applications in support for cellular growth and in systems for bone regeneration. The piezoelectric strain tensor element d(14), the elastic constant s(55) and the dielectric permittivity 8(11), were measured for the anionic collagen and collagen-HA films. The thermal analysis shows that the denaturation endotherm is at 59.47 degreesC for the collagen sample. The collagen-HA composite film shows two transitions, at 48.9 and 80.65 degreesC. The X-ray diffraction pattern of the collagen film shows a broad band characteristic of an amorphous material. The main peaks associated to the crystalline HA is present in the sample of collagen-HA. In the collagen-HA composite, one can also notice the presence of other peaks with low intensities which is an indication of the formation of other crystalline phases of apatite. The scanning electron photomicrograph of anionic collagen membranes shows very thin bundles of collagen. The scanning electron photomicrography of collagen-HA film also show deposits of hydroxyapatite on the collagen fibers forming larger bundles and suggesting that a collagenous structure of reconstituted collagen fibers could act as nucleators for the formation of apatite crystal similar to those of bone. The piezoelectric strain tensor element d(14) was measured for the anionic collagen, with a value of 0.062 pC N-1, which is in good agreement compared with values reported in the literature obtained with other techniques. For the collagen-HA composite membranes, a slight decrease of the value of the piezoelectricity (0.041 pC N-1) was observed. The anionic collagen membranes present the highest density, dielectric permittivity and lowest frequency constant f.L. (C) 2001 Elsevier B.V. B.V. All rights reserved.

Photoluminescence in amorphous PLZ

Amorphous and crystalline powder of PLZ was prepared by using the polymeric precursor method. TGA-DSC (Thermal analysis and Differential Scanning Calorimetry) shows the decomposition of polymeric resin, an amorphous phase and the crystallization of powder. Raman scattering of powder shows an amorphous and semicrystalline phase at 450 and 550 degreesC, respectively. XRD (X-ray diffraction pattern) of powder shows high crystallinity at 700 degreesC/3 h. PL (Photoluminescence) analysis of powder at 300 degreesC/3 h shows a broad asymmetric peak at 585 nm and increases of calcining time led to intense peaks of PL at 300 degreesC/6 h. This emission could be attributed to Zr --> O from the oxygen-2p orbitals to the zirconate-3d orbitals. (C) 2003 Elsevier Ltd and Techna S.r.l. All rights reserved.

Efficient Dye-Sensitized Solar Cells Based on the Combination of ZnO Nanorods and Microflowers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da hidrólise enzimática do amido de mandioquinha-salsa (Arracacia xanthorrhiza): efeito do tamanho dos grânulos

Pós-graduação em Engenharia e Ciência de Alimentos - IBILCE

Reação de redução de oxigênio sobre perovskitas La1-xSrxFeyCo1-yO3-δ, para células a combustível de óxido sólido (SOFC)

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Estudo das características estruturais de amidos: efeito do 'annealing', da hidrólise ácida e da hidrólise enzimática

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Geração de segundo harmônico em vidros teluritos TeO2 – LiNbO3

Pós-graduação em Ciência dos Materiais - FEIS

Estabilidade térmica da zeólita A sintetizada a partir de um rejeito de caulim da Amazônia

Zeólita A foi calcinada nas temperaturas de 200, 400, 600, 800 e 1000 °C/2 h para estudar sua estabilidade térmica. A síntese foi feita a partir de um rejeito de beneficiamento de caulim para a produção de papel de uma empresa mineradora localizada na região Amazônica. A caracterização da zeólita A calcinada nas diferentes temperaturas foi realizada por difração de raios X e microscopia eletrônica de varredura. A zeólita A permaneceu estável até 600 °C, havendo apenas variações nas intensidades dos picos em função da temperatura. A 800 °C o padrão de difração apresentado pelo material continuava sendo da zeólita A mas com ausência de alguns picos. A 1000 °C foi constatado que o produto de calcinação era constituído de nefelina, mulita e provavelmente sodalita. Essa zeólita também foi aquecida em mais duas temperaturas, 900 e 950 °C, com o objetivo de confirmar os dois picos exotérmicos observados em curva de análise térmica diferencial. Os produtos de calcinação nessas temperaturas eram constituídos de nefelina, sodalita e mulita.

Titanate nanotubes produced from microwave-assisted hydrothermal synthesis: Photocatalytic and structural properties

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudos estruturais com a importina-α do fungo Neurospora crassa e sequências de localização nuclear

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Physicochemical and structural characteristics of rice starch modified by irradiation

This work evaluated the physicochemical and structural properties of rice starch of the cultivars IAC 202 and IRGA 417 modified by irradiation. Starch samples were irradiated by (60)Co in doses 1, 2 and 5kGy, on a rate of 0.4kGy/h. A control not irradiated was used for comparison. The granule morphology and A-type X-ray diffraction pattern were not altered by irradiation. There was an increase in amylose content, carboxyl content and acidity with irradiation. Gamma radiation did not affect the thermal properties of IAC202, but increased gelatinization temperature of IRGA417, in the higher dose (5kGy). The number of long chains of amylopectin was reduced and short chains were increased for IAC202, whereas for IRGA 417, the opposite was observed, probably due to cross-linking of starch chains. Starches had their physicochemical and structural properties modified by irradiation differently.